Ping local IP devices

Similar Questions

• 871W wired connect/ping with wireless devices

  Hello

  I have a 871W giving me fits.  I've been troubleshooting this for some days now and may not know what I am doing wrong.  My wired clients cannot communicate with wireless devices.  My wireless devices are unable to communicate with each other.  However, my wireless devices CAN connect to a wired device!  I know because I have a local webmail server on the side wired can be achieved wireless.  All devices, wired and wireless, are on VLAN 1, which is be the only vlan configured.

  My configuration file properly disinfected is attached.

  When I try to ping from a wired device to a wireless device, I get the following error:

  ~ $ ping 172.27.44.27
  PING 172.27.44.27 (172.27.44.27) 56 (84) bytes of data.
  From 172.27.44.3 icmp_seq = 1 Destination Host Unreachable
  From 172.27.44.3 icmp_seq = 2 Destination Host Unreachable
  From 172.27.44.3 icmp_seq = 3 Destination Host Unreachable
  From 172.27.44.3 icmp_seq = 4 Destination Host Unreachable
  From 172.27.44.3 icmp_seq = 5 Destination Host Unreachable
  From 172.27.44.3 icmp_seq = 6 Destination Host Unreachable

  -172.27.44.27 - ping statistics
  8 packets transmitted, 0 received, + 6 errors, 100% of time packet loss 7051ms
  pipe 3

  ~$

  Wireless devices simply timeout trying to ping each other.

  Thank you for your help.

  Chris

  Is there a firewall on the host wireless?

  Do you have wiresharked any traffic to see if it is to hit the dest host?

  Look at the config looks ok. Some additional ACL that I've not seen it used is here.

  Can ping wireless and wired a public IP address?

• Cannot ping local interface after last criticism of microsoft update

  I just bought a Satellite Pro A200.
  When I upgraded to the latest critical updates from Microsoft Update, I found that I could ping is no longer my local IP address. This has happened to the card NETWORK LAN RJ45 and the wireless network card.
  I reinstalled the operating system using the recovery CD, and I could ping to the IP address of the local interfaces.
  But when I again once downloaded and installed the latest critical updates from Microsoft, I can't ping the local IP address.
  Anyone has any idea why?
  Thank you

  Hey Buddy,

  WHERE´s the problem? I know that the updates are the system destroy it when they are buggy, but that's normal with microsoft. I have almost the same problems also! Thhoughts WGAnotify.exe, I was a software pirate and restricted my access to 'zero' access.
  "Yes, Sir, I bought a windows and it s stolen... well... OK... :(."
  Yes, noone except microsoft (who would be the point where I could say "you are in the wrong forum" ;)) knows why it s happening.)
  These days, you should do the following: find update is the cause of this error. You can do this by going in "Add / Remove Programs" in your "Control Panel" and click on the top of the window the button "see the updates.
  Then begin to uninstall the last installed update and check if your ping works. Otherwise, proceed to the next update and uninstall it and so on...
  I know it's a long and boring process, but since there is NO problem of toshiba, you must accept it and try my method to remove the update that is causing your error.

  Welcome them

• found wireless local access device has no fa internet access

  Hello friends please help I have Sony model led tv KDL-32EX520 wifi ready I have brought a UWA BR100 for WIFI, IT DETECTS my wifi but it says:

  found wireless device
  local access failed
  Internet access failed

  Pls help me pls!

  Thank you for your post and welcome to the forums.

  Please click on the link and follow the troubleshooting steps:

  https://us.en.KB.Sony.com/app/answers/detail/A_ID/32464

• ACS 4.0 Local firewall devices

  All,

  I just read a message labeled "ACS 4.0 firewall" and he talked about opening 2004 for 5000 ports to access the ACS server that is behind the firewall. My question is this same range of ports apply if you try to access and authenticate on a device that is behind a firewall. When I try to access one of my devices located behind the firewall I can't authenticate via the GBA so I find myself using the local username and password. Can someone tell me what are the ports I need to open the firewall to allow the authetication return to the ACS server. Thank you

  Hello

  GANYMEDE + authentication service between network devices and AAA server is running on TCP 49. The port 2004-5000 range applies only if you need to access the ACS server (for the purposes of management) from the outside / internet. In your case, if you want to access your devices behind the firewall from external network, what you need is to map your internal network with the public IP devices and open the port of ddesired service, for example SSH (tcp 22) on your Firewall outside interface ACL to allow incoming access.

  For your internal devices, you must have the configuration appropriate AAA that point to ACS (e.g. GANYMEDE +). In your GBA, set these devices as customer AAA and set up appropriate IP, key secret and using GANYMEDE +.

  Before testing ssh access internet/external network, test your SSH access locally. He must succeed in getting AAA to authenticate your request of SSH connection.

  http://www.Cisco.com/en/us/partner/products/sw/secursw/ps2086/products_user_guide_chapter09186a008052e996.html

  I hope this helps.

  Rgds,

  AK

• ESX Server guests and Local USB devices

  Is this possible with ESX Server 3.5 to connect to a guest operating system and load a USB device as a card reader connected to your laptop remotely?  How if possible?

  Is there a device that can be installed for the smart card reader, biometric readears, etc.. ??

  To summarize how ESX allows a remote user to plug in a usb device locally and have ESX assign to the team desired vmware instance?

  Thank you and sorry to be so green!

  Green is in fashion now Kyle - get with the program!

  MNANCE152 - doesn't this sound viable, or do you think you will have to take another route?  I'd be interested to hear what you come in the end, if you don't mind me posting it here.

  Good luck!

• How can I save a pdf file on my local mobile device without using iTunes? [iOS 9 Beta]

  I just know... I can't save a PDF of safari or by e-mail at my iPad...

  I open it... But when I type 'my documents' and try to return back and rename the files... nothing happens...

  
  

  the file I opened is not in my local machine... I can not find...

  going on what?  Help me pls...

  thx a lot

  Hello

  This particular compatibility problem iOS 9 has been fixed in Adobe Reader for iOS version 15.1.0 (released August 11, 2015).

  Open PDF documents from other applications (Mail, Safari) via the function "open in" should now appear in the sections 'Local' and 'Recent '.

  Please try it and let us know if you find other problems with iOS 9 beta.

  Thank you very much for your help!

• ASA VPN cannot ping ip local pool

  Hello

  We have ASA 5510 a device be deployed for a period of time. Everything works fine except customers local VPN cannot ping local customer VPN which get their IP address to the local swimming pool. They can ping anywhere on the local network of company, but not each other. I don't know there's a logical explantion for this because of an ACL but all appreciated the advice...

  Thanks in advance

  Keith

  Hi Keith,

  I think that, in order to allow a customer VPN reach another VPN client, the SAA should turn the VPN traffic (because it will receive the traffic of a VPN tunnel and re - again to send another tunnel.)

  Can you add "same-security-traffic intra-interface permits" and try again?

  Federico.

• Two of us have MacBook and iPhone and you want to share a library on the local hardware. We want to get the photos off the coast of our devices to save memory. Recommendations of the how?

  How can I put any libraries of MacBooks and iPhotos in a single library on a local, external device to give us access and eliminate our cameras?

  An iPhoto Library is a library of unique user. If you try to open different user accounts, you will have problems with the file ownership.

  For iPhoto libraries the workaround is to move the library to an external drive, where the "Ignore ownership on this volume" indicator is on.  The procedure is explained in this document, see the link: iPhoto: sharing libraries among multiple users - Apple Support

  https://support.Apple.com/en-us/HT201517

• NT WS - VPN 3.6.3 Client - Ping problem

  When I install the Client VPN 3.6.3 on an NT Workstation. I ping is no longer the WS NT from other devices on the internal LAN? This is when the VPN client is not yet connected. Everything is fine, but no response to pings locally on the other side of NT?

  ??

  Thank you

  Bob

  You have the stateful firewall "always you" checked. This is a version of the Zonealarm firewall Runtime based on the host. It's 'on' even when you're not connected via VPN client. Great security.

• VPN connects but can't access internal devices

  Thanks in advance for any help that can be provided.

  I use AnyConnect to create a VPN with an ASA 5505.  Once connected, the client needs to access a device behind a router in 1941.

  Internally, (without using VPN), all my itinerary runs correctly.  My VPN client can connect and when I put a route on my router from 1941, I am able to ping this particular device.  But my VPN client cannot appear ping all the remaining devices on the same internal range as the ASA 5505 or whatever happened on 1941.

  Device far router VPN Client ASA 5505 1941 Workstation

  192.168.201.20---> outside IP x.x.x.x / / internal 192.168.101.1 192.168.101.56 192.168.101.2 / / 192.168.8.1 192.168.8.150

  Client connects and get the IP address of the ASA

  Cannot ping it cannot ping

  Can ping the internal IP address of 1941

  * (after creating a static route)

  I was playing with my setup intensively to try to make this work.  Split tunneling is enabled and is required.

  Here is my current config:

  hostnameMYHOST

  activate mUUvr2NINofYuSh2 encrypted password

  UNDrnIuGV0tAPtz2 encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  switchport access vlan 7

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.101.1 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.0.0

  !

  interface Vlan7

  prior to interface Vlan1

  nameif DMZ

  security-level 20

  IP 137.57.183.1 255.255.255.0

  !

  passive FTP mode

  clock timezone STD - 7

  DNS domain-lookup outside

  the obj_any_dmz object-group network

  192.168.101.0 IP Access-list extended sheep 255.255.255.0 allow all

  192.168.201.0 IP Access-list extended sheep 255.255.255.0 allow all

  tunneling split list of permitted access standard 192.168.101.0 255.255.255.0

  pager lines 24

  Enable logging

  debug logging in buffered memory

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 DMZ

  mask 192.168.101.125 - 192.168.101.130 255.255.255.0 IP local pool Internal_Range

  IP local pool vpn_pool 192.168.201.20 - 192.168.201.30 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global interface 10 (external)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (DMZ) 10 137.57.183.0 255.255.255.0

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  Route inside 192.168.8.0 255.255.255.0 192.168.101.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  http server enable 64000

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Crypto ca trustpoint ASDM_TrustPoint1

  registration auto

  name of the object CN = MYHOST

  ClientX_cert key pair

  Configure CRL

  string encryption ca ASDM_TrustPoint1 certificates

  certificate 0f817951

  308201e7 a0030201 30820150 0202040f 0d06092a 81795130 864886f7 0d 010105

  05003038 31173015 06035504 03130e41 494d452d 56504e2d 42415455 53311d 30

  1b06092a 864886f7 0d 010902 160e4149 4d452d56 504e2d42 41545553 301e170d

  31333036 32373137 32393335 5a170d32 33303632 35313732 3933355a 30383117

  30150603 55040313 0e41494d 452-5650 4e2d4241 54555331 1d301b06 092 d has 8648

  86f70d01 0902160e 41494d 45 2d56504e 424154 55533081 9f300d06 092 2d has 8648

  86f70d01 01010500 03818d 30818902 00 818100c 9 ff840bf4 cfb8d394 2 c 940430

  1887f25a 49038aa0 1299cf10 bda2a436 227dcdbf f1c5566b c35c2f19 8b3514d3

  4e24f5b1 c8840e8c 60e2b39d bdc0082f 08cce525 97ffefba d42bb087 81b9adb9

  db0a8b2f b643e651 d17cd6f8 f67297f2 d785ef46 c3acbb39 615e1ef1 23db072c

  783fe112 acd6dc80 dc38e94b 6e56fe94 d59d5d02 03010001 300 d 0609 2a 864886

  8181007e f70d0101 05050003 29e90ea0 e337976e 9006bc02 402fd58a a1d30fe8

  b2c1ab49 a1828ee0 488d1d2f 1dc5d150 3ed85f09 54f099b2 064cd 622 dc3d3821

  fca46c69 62231fd2 6e396cd1 7ef586f9 f41205af c2199174 3c5ee887 42b684c9

  7f4d2045 4742adb5 d70c3805 4ad13191 8d802bbc b2bcd8c7 8eec111b 761d89f3

  63ebd49d 30dd06f4 e0fa25

  quit smoking

  crypto ISAKMP allow outside

  crypto ISAKMP policy 40

  preshared authentication

  aes-256 encryption

  sha hash

  Group 5

  life 86400

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 0.0.0.0 0.0.0.0 DMZ

  SSH timeout 10

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1

  SSL-trust outside ASDM_TrustPoint1 point

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image

  enable SVC

  internal ClientX_access group strategy

  attributes of Group Policy ClientX_access

  4.2.2.2 DNS server value

  VPN-tunnel-Protocol svc

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunneling

  access.local value by default-field

  the address value vpn_pool pools

  IPv6 address pools no

  WebVPN

  SVC mtu 1406

  generate a new key SVC time no

  SVC generate a new method ssl key

  username privilege 15 encrypted password ykAxQ227nzontdIh ClientX

  ClientX username attributes

  VPN-group-policy ClientX_access

  type of service admin

  tunnel-group ClientX type remote access

  attributes global-tunnel-group ClientX

  address pool Internal_Range

  Group Policy - by default-ClientX_access

  type tunnel-group SSLClientProfile remote access

  attributes global-tunnel-group SSLClientProfile

  Group Policy - by default-ClientX_access

  type tunnel-group ClientX_access remote access

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:da38065247f7334a5408b7ada3af29ae

  : end

  OK, lets go on... ;-)

  Split tunneling: the ACL must include all the networks you want to join via the VPN:

  tunneling split list of permitted access standard 192.168.101.0 255.255.255.0

  tunneling split list of permitted access standard 192.168.8.0 255.255.255.0

  NAT: Do not use 'everything' in the nat exemption, but specify all the traffic that should not be natted:

  IP 192.168.101.0 allow Access-list extended sheep 255.255.255.0 192.168.201.0 255.255.255.0

  IP 192.168.8.0 allow Access-list extended sheep 255.255.255.0 192.168.201.0 255.255.255.0

  Routing: The 1941 needs a route for the vpn-pool pointing on the SAA (just in case there is no default route to the ASA)

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• Install new ESX hosts.  Cannot Ping.

  Hi all

  I'm building a test lab which so far consists of:

  ESX1: 20.1.1.10 255.255.255.0

  vCenter: 20.1.1.100 255.255.255.0

  Openfiler iscsi: 20.1.1.40 255.255.255.0

  I had all these configured devices and can ping throughout (with a little help from you friendly people, of course). I just tried to install my second esx host and I have a few problems to get to communicate with the rest. During installation I assigned an IP address of 20.1.1.80 255.255.255.0 so its on the same network. Rattling of the evil machine returns "destination host unreachable". Ping to it from any other device returns the same. esxcfg-NICS - l is the network card. Route - n shows exactly the same output as my other work esx host.

  This workshop is entirely on its own network. All devices are networked through a simple switch 16-port Dell 2216 with any VLAN or whatever it is.

  I tried all sorts of troubleshooting a layer on my switch ports, including the passage of the cables, and finally pulling up the entire hard drive and put it in a same laptop to rule out a bad network card. I also went into the bios and adapted settings my host to work to avoid any possible problem of allocation of resources.

  One strange thing I noticed. When I run esxcfg-nics command on my network card work esx host is displayed. When I pull on the cable and run the command, it displays down. Plug it in again, almost immediately goes back to the top. However, when I try the same process on this machine of boredom, the NIC appears whether or not the cable is connected some sort of funny business going on here. What Miss me?

  EDIT: I could have taken the lead on this one.  I see now that speed is 0MBPS and is half-duplex.  I gave the esxcfg-NICS-s-100 d full vmnic0 command but esxcfg-NICS-l does not reflect them.  I'll try a reboot, but I think this is probably my problem.

  Faulty network card causes a problem of driver especially problem run miit-tool to check the duplex speed and also his ping locally? stop the firewall during the tests of time and running tcpdump on interface to control icmp traffic.

  ifconfig - a vswif0 control is in place and the correct ip address?

  Thank you

  Pitoux

  -Path to the virtual world.

• Ping target RT

  Hello!

  I have an application that runs on an RT target that must carry out periodic checks on the devices should be plugged on the target subnet.

  It is possible to perform a ping to an RT target?

  Thanks in advance for any suggestion,

  Marco

  Hello!

  I just realized that the same problem has been published here: http://forums.ni.com/t5/LabVIEW/How-to-Ping-a-network-device-from-RT-controller/td-p/1535420

  the solution proposed by BlueCheese seems to work for me.

  Kind regards

  Marco

• Redirection problem strange local drive - white icons

  Someone has seen this before and no one knows the cause/solution?

  What is happening on our test/development configuration and our production environment (vWorkspace 7.1).

  When a user connects to a Windows 7 VDI session local endpoints devices are directed through, as shown here:

  

  But... when the same user connects to a Win2008 R2 RDS session, the redirected folders are missing and you get white icons that are inactive.

  

  The user is using folder redirection to move its profile folders (AppData, etc.) on a network share...

  Endpoints tested 2 with are Windows 7.

  Any ideas why this might be happening?

  See you soon,.

  Dan.

  Possibly a registry hive capturing the issue (or lack thereof).

  On the test in question account, there is no record capturing the policies put in place for the user. I set it up to capture booty HKCU\Software\Microsoft and HKCU\Control Panel.

  The client drives appear now.

  I will tune the registry capturing next week.

  Odd. Don't know if it's an underlying problem of the RDP/RDS but at least theres an autour work.

  I'm going to blame another admin here for now!

  Dan.

• Ping PowerEdge 5324 problem

  We buy a new switch Dell Powerconnect 5324 (24 ports) in order to expand our old Powerconnect 2508 (8 ports) for gigabit connectivity.

  If we connect the new switch, we have the following behaviors: a very small number of machines can not ping IP one and only . For example, the print server can ping all printers except one. A PC can ping all other devices connected to the network, except the IP address of a server. At the same time, all other PCs work fine.

  If I disconnect the new switch the entire network restart to function properly. If I connect the servers to the switch again the network problem appears again.

  There are also 2 amazing things:

  -changes of machines involved (IP)

  -a continuous ping on the affected machine works for a few seconds then stop for a few minutes and then work again for a few seconds and so on

  I use the default configuration, and I think that it is impossible to configure something like this with a managed switch.

  Do you have any suggestions?