Pinout of the SPDIF

Similar Questions

• There the SPDIF on Satellite M100?

  There the SPDIF on M100? If Yes, then how do I turn it on?

  New bad guy!
  The audio line out S/PDIF is not available on the Satellite M100.

  You will not be able to active it too

• Does anyone have a pinout for the UMI OR AKD Drive Cable?

  I make a motion controller with an NI 7350 card with evasion NI UMI-7774.  I connect to the UMI-7774 to a drive Kollmorgan AKD with UMI OR AKD drive cable.  This cable has a terminal of 20 pin block which I believe includes the home and limit switch signals, but I don't have a pinout of the UMI to AKD drive cable to verify this.  Anyone know where I can get this pinout?

  Thank you

  Chris

  Hi Chris,

  Can be found on page 8 of the manual of getting started with the NI 7340/7350 and AKD Servo Drives Motors controllers the pinout of the connector terminal screws 20 pins of the UMI to AKD drive cable. Please do not hesitate to let us know if you have any other questions or is not what you are looking for.

  Thank you

• Pinout of the device from the PCI-6225 in differential Mode of I

  Simple question: where is the pinout of the device for the card PCI-6225 for differential of analog input mode? I looked in the device list of the pins in MAX, in the NI 622 x specifications document and several other places, but I was not able to find it. I found the pinout for referenced asymmetrical measures, but no differential.

  Related issue: most people use devices like the 6225 for no entries analog differential? So why in tarnation do many brand of material OR that upper and lower manuals, looking for the differential input version?

  Thank you!

  «Referring the number of pins would make it impossible to use the same code when you change maps DAQ.»

  I'm not sure I followed here. Can you please explain a little further? Are you referring to the 1-68 0 connector pins and 1-68 pin connector 1? If so, I'm not sure, I followed. A different pinout may not change the code. If I had to replace a 6225 with another equivalent at least DAQmx device as many channels and the device number was the same, then I'd not change all the names of channel in the code, I? It would certainly change the wiring, which is precisely what I'm doing right now.

  I know that the analog input channels look like ai0, ai1, etc.. My concern is later: where the jumps occur when you're in differential mode?

  I have attached exactly what I would like to see in the documentation of ALL analog input device which allows the differential mode, only with the + and - channel names only and not the labels AI0-AI79. I couldn't find this photo any place, but rather had to laboriously calculate this pinout. If you know where to find this photo, I would be very grateful.

  Thanks for the reply.

  

• Z400: Z400 firewire pinout of the connector?

  I noticed that the connector on the front panel 1394 connector 12 pin rather than the standard 10 pin. Does anyone know the pinout? It is not in the maintenance manual. Thank you!

  Here is the pinout of the Z400 J13 1394 header.  Keep in mind that it is looking at the head of the motherboard, and not the connector at the end of the connector to the front panel, which could be a reflection, depending on how you look at the connector.

  The best way to determine the pinout is to use the keyed/missing pins as a refrence.

  

• xw9400: xw9400. Pinout of the need for the connectors of the case (no psu connectors, only those in the case)

  I need the list of pins for various connectors case-Strip pin, especially J24 but other multispindle those too.

  Manual of Tyan S2915 Board for is a different version than that of poor quality that they OEM would be at HP for the 9400 and HP Tech Ref for the 9400 only provides pinouts for connectors well defined including pinout lie anywhere.

  The connector of the Panel before xw9400 J34 (there is no J24) pinout, the mother, is map:

  

  There are 2 key positions (lack of spindle) on pins 10 and 15.  Use these empty pins to help identify the signals.

  The pinout is very similar to other former workstations HP.  A few tips:

  -Pins 1 and 3 are for the harddrive activity led.

  -Terminals 2 and 4 are for the power light.  HP systems have back to back LED connected between these pins.  A green is on and functioning normal and red lights (and flashes error codes) when there are errors.

  -Connect a momentary between pins 5 and 6 switch will turn on the computer and off.

  -Connection of a momemtary between pins 7 and 8 switch will force a system reset.

  -PIN 9 is designated as + 5V, but it is powered by a 100 ohm pullup resistor to + 5V, so it will not provide a lot of power.  FOR INFO.

  -SPKR + and SPKR - are for the internal speaker.

  Most of the other connectors xw9400 follow standards of industry, i.e. the IDE drive and floppy connectors.

  Is there anything else you want to know?

• Pinout of the differential

  I want to use the usb-6225 (screw terminals) in differential mode, but I can't find the pinout. Can you help me? Thank you

  Here is a link to the specification.  The list of the pins are at the end.

  http://sine.NI.com/DS/app/doc/p/ID/DS-10/lang/en

  In differential mode, it works in groups of 16.  A0 is the + and A8 is-, A1 + and A9 - etc.  A16 is + and A24 - etc.

• Pinout of the GPIB

  Can someone help me with the pinout for an old matrix printer cable. The cable must have the HPIB/GPIB 24 centronics pins at one end and the usual printer centronics connector 36 pins to another. I have a DB-25 to centronics 36 cable I will be just cut the DB25 and solder the PIN 24. 8 data pins are not a problem. What I understand, it's where other signals should be terminated. I can't find where I can buy such a cable, so I'll try to build a.

  Thank you

  Jeff

  Thanks for your reply Dennis.

  Now that you have raised this theory, I can't be sure of myself now. I need to watch it, because, the plotter and digitizer are GPIB and the printer of the dam was probably too. It seems quite logical. Now I have to find a way to move forward.

  Thanks again,

  Jeff

• Pinout of the SPS224G4

  Does anyone have the list of pins to make a Seraglio of cable to connect a pc to the switch LINKSYS SPS224G4?

  Thank you!

  Hello

  The SPS224 console cable must be the same as the older the SRW series switch

  OK, I took out my multimeter and checked the list of pins on my cable from the console that I use to connect to my SRW2008P.

  My cable SRW2008P console on the two DB9 female connectors pinout is 1 to 1.

  In other words easily DB9 female-female cable available with the following pinout.

  1-------------1

  2-------------2

  3-------------3

  4-------------4

  5-------------5

  6-------------6

  7-------------7

  8-------------8

  9-------------9

  Best regards, Dave

• Satellite P100 (PSPAAE) - SPDIF and helmet is the only audio options

  Interface SPDIF and the helmet is the only options for audio output, if the SPDIF of my sound card? Speakers work when using the webcam, but not now it are disconnected?

  Hi vickylou001,

  Probably, you need to reinstall the audio driver. It might be something wrong with the audio output of the audio driver settings. In order to check the Web from Toshiba site to download the audio driver and reinstall.

  By the way: what OS do you have?

  Did you notice the same problems before installing Logitech webcam software?

• Satellite 1900 305 battery, need the pinout numbers

  I wonder if anyone knows numbers pinout of the details of the connection of the battery from the battery used with the Satellite 1900 305

  Mine has not been used for a few months and the battery is completely flat and is not supported.

  I want to check battery volts and check that there volts at the terminals in the computer.

  Martin

  Hello

  Unfortunately, there isn't any info on battery pin out. These documents are available only for the Toshiba ASP.

  But the battery charging is controlled by a microprocessor to power supply which is mounted on the system board. Power of orders by microprocessor if the accusation is enabled or disabled and detects a full charge when the power adapter and the battery are connected to the computer. The system charges the battery in charging or trickle charge.
  Normal load (power) 8 hours or more
  Fast (power off) charge about 4 hours

  Fast battery charge:
  When the adapter is attached, there are two types of fast charging: charging when the system's power off and normal load when the system is turned on.

  However, if the following occurs, the battery charging process stops.

  1. the battery is fully charged.
  2. the power adaptor or the battery is removed.
  3. the output or battery voltage is abnormal.
  4. the temperature of the battery is abnormal.
  5. battery SMBus communication fails.
  6. the battery cell is bad.

  In your case, it is possible to s that the batteries are dead, and you need a new battery.

• Equium 80 - 132 has PSA87E - the LCD connector pinout

  Can someone help me or direct me to a site (if not here :)) where I can find the pinout of the connector from the motherboard to the LCD from a satellite
  with
  model name: EA80-132
  Model No.PSA87E - 0030069K

  Hello

  I tried to find all the manuals but unfortunately without success. If you search for the connector on the motherboard where you can plug the display cable, it should be placed somewhere in the middle. When the keyboard is removed check connector in the upper mid position (tails).

  Sorry, but I wasn't able to find any nice document with screenshot. In any case I hope that you will be able to find the right connector.

• Qosmio G30: Option unavailable SPDIF in the Audio properties

  Qosmio G30, SigmaTel HD Audio Codec, running XP 2

  I'm looking for audio signal through the built in coaxial to the GPA. No signal. When I go to sounds and Audio devices > advanced > Volume Control Panel /Properties there is no cursor for spdif badette, in the list of things to show in the advanced Panel, or a way to put in operation. Similarly, in sign of SigmaTel there no option to route via spdif.

  In addition, the advanced controls is grayed out in the Volume Control Panel.

  What did I miss? I can't for the life of understand me why there is no signal nor any how to activate spdif in this machine.

  In addition, in the Media control Devices Properties box, it is this list:
  (MCI) Audio CD
  (MCI) Microsoft Video for Windows
  Midi sequencer (MCI)
  Sound (MCI)
  mciqtz32.dll

  Who say that they are functioning normally. Any ideas why I can't find the spdif option?

  Thanks in advance.

  Hello

  The SPDIF socket is supported on the Qosmio G30. It s the same taken as the headphone jack.
  To use this SPDIF you must connect the audio amp with the laptop via a special SPDIF cable.

  What you could do is to start the DirectX using the command; Dxdiag

  There you can check if the SPDIF is available or not.

• Qosmio F60 - 00Y has an optical output of the Audio (toslink\spdif)?

  The Australian model of Toshiba Qosmio F60 has an optical audio output?

  Hello

  I found this page of Toshiba Qosmio F60 - 00Y on:
  http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?MessageID=194743

  Unfortunately, there is nothing on SPDIF and digital output.
  I found some details about the European series F60 and didn t find info on SPDIF

  For me, it seems that the SPDIF is not available but it's just a guess

• Re: Satellite P300-135: No. SPDIF in 'His' Panel after the installation of SP1

  Before this one had speakers, HDMI and SPDIF.
  Now - only speakers and HDMI.

  After all the works of S/PDIF through speakers device, but only in stereo mode.
  I need 5.1 DD!

  Could be another reason for that?

  Hello

  The SPDIF port is certainly available on this laptop.
  I remember that some devices can be hidden, if they are not enabled.

  So maybe you can do a right click in the Panel-> Sound and could mark called options hidden devices and features see the disabled.

  Then the SPDIF should reappear.

  Check it!