PIX 501 and THE, 3DES, AES

For a version newly produced PIX 501,

(1) are DES, 3DES and AES activation keys all pre-installed?

(2) how I can find on which of them is pre-installed on my PIX 501?

(3) when I create a server VPN (on the PIX 501), I see that all three OF THEM, 3DES and AES are available in the drop-down list of the PDM configuration screen. Does that mean my PIX 501 have all three of them (FROM THE, 3DES and AES)? -If the answer is no, assume that only is preinstalled on PIX 501, then why/how can appear in the drop-down list the 3DES and AES?

Thank you for helping.

Scott

Should be integrated already. depends on the way the news is your PIX 501.

To be sure to log in to the console and type:

See the version

See the example output version:

See the pixfirewall version (config) #.

Cisco PIX Firewall Version 6.2 (3)

Cisco PIX Device Manager Version 2.0 (1)

Updated Thursday April 17 02 21:18 by Manu

pixdoc515 up to 9 days 3 hours

Material: PIX - 515, 64 MB RAM, Pentium 200 MHz processor

I28F640J5 @ 0 x 300 Flash, 16 MB

BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

0: ethernet0: the address is 0050.54ff.3772, irq 10

1: ethernet1: the address is 0050.54ff.3773, irq 7

2: ethernet2: the address is 00d0.b792.409d, irq 11

Features licensed:

Failover: enabled

VPN - A: enabled

VPN-3DES: enabled

Maximum Interfaces: 6

Cut - through Proxy: enabled

Guardians: enabled

URL filtering: enabled

Internal hosts: unlimited

Throughput: unlimited

Peer IKE: unlimited

Serial number: 480221353 (0x1c9f98a9)

Activation key running: 0x36df4255 0x246dc5fc 0x39d2ec4d 0x09f6288f

Modified configuration of enable_15 to 12:15:28.311 UTC Wednesday, may 1, 2002

pixfirewall (config) #.

Here, you should see if THE or 3DES, AES encryption is active or not. If you have just SOME so you can use the following link and get for free a new activation key that allows 3DES and AES.

https://Tools.Cisco.com/swift/licensing/JSP/formGenerator/Pix3DesMsgDisplay.jsp

sincerely

Patrick

Tags: Cisco Security

Similar Questions

  • PIX 501 and VPN Linksys router (WRV200)

    I inherited a work where we have a Cisco PIX 501 firewall to a single site and Linksys WRV200 Router VPN on two other

    sites. Asked me to connect these routers Linksys firewall PIX via the VPN.

    According to me, the Linksys vpn routers can only connect via IPSec VPN, I'm looking for help on the configuration of the PIX 501 for the linksys to connect with the following, if possible.

    Key exchange method: Auto (IKE)

    Encryption: Auto, 3DES, AES128, AES192, AES256

    Authentication: MD5

    Pre Shared Key: xxx

    PFS: Enabled

    Life ISAKMP key: 28800

    Life of key IPSec: 3600

    The pix, I installed MDP and I tried to use the VPN wizard without result.

    I chose the following settings when you make the VPN Wizard:

    Type of VPN: remote VPN access

    Interface: outside

    Type of Client VPN device used: Cisco VPN Client

    (can choose customer of Cisco VPN 3000, MS Windows Client by using the client MS Windows using L2TP, PPTP)

    VPN clients group

    Name of Group: RabyEstates

    Pre Shared Key: rabytest

    Scope of the Client authentication: disabled

    Address pool

    Name of the cluster: VPN - LAN

    Starter course: 192.168.2.200

    End of row: 192.168.2.250

    Domain DNS/WINS/by default: no

    IKE policy

    Encryption: 3DES

    Authentication: MD5

    Diffie-Hellman group: Group 2 (1024 bits)

    Transform set

    Encryption: 3DES

    Authentication: MD5

    I have attached the log of the VPN Linksys router VPN.

    This is the first time that I have ever worked with PIX so I'm still trying to figure the thing to, but I'm confident with the CCNA level network.

    Thanks for your help!

    Hello

    Everything looks fine for me, try to have a computer in every network and ping between them. Check the newspapers/debug and fix them.

    Let me know.

    See you soon,.

    Daniel

  • PIX 501 in the firewall of the Web server

    Hello

    At the suggestion of a colleague, we bought a firewall PIX 501 to protect our new Win2003 web server and a UNIX/Oracle DB server.

    I've never worked with before firewalls.

    Our servers are located in a cage at the ISP and belong to us. There are only two servers providing web site. I have read the documentation in the Getting Started book and it does not answer my question.

    We have 2 web sites with different IP numbers on our web server. Let's say 140.5.5.4 and 140.5.5.5. I understand that I have will redefine the numbers with the firewall (192,...) but I do not understand how the routers at the ISP will be able to route requests for two websites to the firewall when it has one IP number, say 140.5.5.1?

    Any help is appreciated.

    Thank you, Jerry

    Jerry,

    what you are referring is called port forwarding. Whether you a PIX with a public IP address 12.1.1.1 and your web servers are respectively and 12.1.1.2 12.1.1.3. Port forwarding is really a 2 step process:

    * a static translation of the public IP address of the PIX (12.1.1.1) at the address of the web server (12.1.1.2)...

    static (inside, outside) tcp 12.1.1.1 12.1.1.2 www www netmask 255.255.255.255 0 0

    * an intermediate statement basically "all web requests should be allowed in the pix outside of the interface"...

    driving permit tcp host 12.1.1.1 eq www everything

    Here is a link that will help you to clarify this point:

    www.Cisco.com/warp/Customer/707/28.html

    This should help you get started. Regarding the basic configuration, it takes config examples on the Cisco site, if you have access CCO.

    Let me know if it helps.

    Rob H.

  • Problems with PIX 501 and Server MS Cert

    Hi all

    I have two problems with my PIX 501:

    1. registration works well. The pix has a certificate and use it with SSL and VPN connections. But after a refill, the pix certificate is lost and it has regenerated again self-signed certificate!

    Yes, I wrote mem and ca records all!

    2. at the request of ca CRL , I get the following debugging:

    Crypto CA thread wakes!

    CRYPTO_PKI: Cannot be named County ava

    CRYPTO_PKI: transaction GetCRL completed

    Crypto CA thread sleeps!

    CI thread wakes!

    And the CRL is empty.

    Does anyone have any idea?

    Bert Koelewijn

    Not sure about 1, but 2 is usually caused by the COP (Point of Distribution of CRL, basically the situation where the PIX can download the Revocation list from) listed in cert CA is in a format the PIX does not, generally an LDAP URL.

    Check the following prayer:

    Open the administration tool of CA (Certification Authority) then

    (1) right click on the name of CA and choose 'properties '.

    2) click on the tab "Policy Module".

    3) click on the button "configure."

    4) click on the tab "X.509 extensions".

    > From there, it can display the list of the "CRL Distribution Points".

    Turn off everything that isn't HTTP.

    You need to reinstall the CERT in the PIX, I think, but then it should be able to download the CRL through HTTP instead of LDAP.

  • L2L pix 501 and remote access VPN

    Hi, I'm working on an old 501 PIX w / Software 6.3 (5), he already have access to remote VPN configuration and works very well, but now he needs a L2L implemented. One thing I try to do all the work remotely via VPN or ssh to the machine. I don't know what's on the other end, but they swear that it is set up and maybe my problem is when I start putting in orders for the other VPN it breaks the remote VPN access. One thing that I have to do is NAT a host on the inside to appear as another host on the end. I use these commands and I think it works cannot be said.

    access-list 101 permit ip remote_network 255.255.255.0 local_server host

    public static 10.1.0.203 (inside, outside) - access list 101

    then

    access-list 102 permit ip host 10.1.0.203 192.168.50.83
    access-list 102 permit ip host 10.1.0.203 192.168.50.86
    access-list 102 permit ip host 10.1.0.203 192.168.50.50
    access-list 102 permit ip host 10.1.0.203 192.168.50.85

    and use it to match against

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    EMDs-map 10 ipsec-isakmp crypto map
    correspondence address card crypto emds-map 10 102
    card crypto emds-map 10 peers set remote_vpn_server
    card crypto emds-card 10 set of transformation-ESP-3DES-SHA

    then

    ISAKMP key magic_key address remote_vpn_server netmask 255.255.255.255
    ISAKMP identity hostname
    part of pre authentication ISAKMP policy 10
    ISAKMP policy 10 3des encryption
    ISAKMP policy 10 sha hash
    10 1 ISAKMP policy group
    ISAKMP life duration strategy 10 86400

    and that is where it usually breaks the VPN, I don't know if the other VPN works due to not being not able to get to this server to try to ping, I don't really like to try this stuff remotely but I don't have a lot of choice at the moment.

    Any thoughts?

    Thank you

    Jarrid Graham

    Yes, just use the number of different sequence with 1 name of the crypto map. Please also ensure that your dynamic crypto map, which is your vpn client has the sequence down the crypto map (more), because you want to make sure that the static crypto map (for lan-to-lan tunnel has higher sequence number (lower number)).

    The political isakmp sequence number does not match, it is processed from top to bottom (number less than the high number) and also long 1 set of isakmp policy corresponds to the remote peer, it will be negotiated properly.

    Hope that answers your question and please note useful post. Thank you.

  • PIX 501 and pcAnywhere access rules

    Hello

    I'm having a problem with the implementation of pcANywhere remote access Access 2 servers on the inside network. I created 2 static rules and access lists 2 to start, but I can't get thru to the server. These are the settings

    static (inside, outside) 7x.x.x.x 5631 172.16.x.x tcp 5631 255.255.255.255

    static (inside, outside) udp 7x.x.x.x 172.16.x.x 5632 5632 255.255.255.255

    list of allowed inbound tcp access any host 172.16.x.x eq 5631

    list of allowed inbound udp access any host 172.16.x.x eq 5632

    Access-group interface incoming outside

    Version 6.3 of the PIX using

    I also tried access server list terminal server because another method of access, but not go either.

    There are no other rules.

    Any ideas why this would not work?

    TIA

    Vince

    your external ACL must mention the public IP address of your server:

    list of allowed inbound tcp access any host 7x.x.x.x eq 5631

    list of allowed inbound udp access any host 7x.x.x.x eq 5632

  • PIX 501 to allow access to the ftp server

    Hello

    We have a public ip address of the pix 501 and the other, I want to access the ftp server on the internal network from the outside. I tried to configure the PDM by a static nat, which translate to the address of the FTP to the public address, but then none of the stations networks could out - how can I configure it?

    I would also like to know what ports should I open on the acl for access to the ftp server.

    Thank you, daguech

    Yes, sorry... You must use the unique host for addresses command. The access list is applied to your external interface?

    for example, the command would be:

    Access-group acl_out in interface outside

    Also, can you connect to the local ftp server behind a firewall?

  • Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.

    I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.

    .

    The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).

    .

    A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?

    .

    I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?

    .

    Thank you.

    UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.

    The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.

  • L2l IPSec VPN 3000 and PIX 501

    Hello

    I have a remote site that has a broadband internet connection and uses a PIX 501.  We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.

    I followed the following documentation:

    http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml#tshoot

    However the L2L session does not appear on the hub when I check the active sessions.

    The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.

    Any help or advice are appreciated.

    I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.

    For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.

    Here is an example of sample config

    http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

    I hope this helps!

  • QoS is supported on the Cisco PIX 501 or 506th?

    Hello

    There is no mention of QoS in technical for the PIX 501 and 506 records but nothing for the 515. PIX OS 7.x configuration guides do not mention specific material support.

    Does anyone know if QoS is taken care of in the 501 or 506th - I need support lines expectations for VoIP over IPSec.

    Thank you

    Chris

    QoS is supported in 7.x code, you would have to level 501/506 to 7.x code, but this is not supported on these two models, the next logical solution would be to upgrade your PIX 501/506 to asa5505s.

    Rgds

    Jorge

  • Customer Cisco PIX 501 VPN connects but no connection to the local network

    Hi all:

    I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.

    I have attached the PIX configuration.

    Advice will be greatly appreciated.

    ********************

    6.3 (5) PIX version

    interface ethernet0 car

    interface ethernet1 100full

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    enable password xxxx

    passwd xxxxx

    pixfirewall hostname

    domain ciscopix.com

    fixup protocol dns-length maximum 512

    fixup protocol ftp 21

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol http 80

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol sip 5060

    fixup protocol sip udp 5060

    fixup protocol 2000 skinny

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol tftp 69

    names of

    access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

    access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

    pager lines 24

    Outside 1500 MTU

    Within 1500 MTU

    IP address outside dhcp setroute

    IP address inside 192.168.1.1 255.255.255.0

    alarm action IP verification of information

    alarm action attack IP audit

    IP local pool ippool 192.168.2.1 - 192.168.2.5

    location of PDM 192.168.2.0 255.255.255.0 outside

    PDM logging 100 information

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) - 0 102 access list

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    Timeout xlate 0:05:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

    H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

    Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    AAA-server GANYMEDE + 3 max-failed-attempts

    AAA-server GANYMEDE + deadtime 10

    RADIUS Protocol RADIUS AAA server

    AAA-server RADIUS 3 max-failed-attempts

    AAA-RADIUS deadtime 10 Server

    AAA-server local LOCAL Protocol

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

    Crypto-map dynamic dynmap 10 transform-set RIGHT

    map mymap 10-isakmp ipsec crypto dynamic dynmap

    mymap outside crypto map interface

    ISAKMP allows outside

    ISAKMP identity address

    part of pre authentication ISAKMP policy 10

    encryption of ISAKMP policy 10

    ISAKMP policy 10 md5 hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    vpngroup vpn3000 ippool address pool

    vpngroup vpn3000 Server dns 68.87.72.130

    vpngroup vpn3000-wins 192.168.1.100 Server

    vpngroup vpn3000 split tunnel 101

    vpngroup vpn3000 downtime 1800

    password vpngroup vpn3000 *.

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd address 192.168.1.2 - 192.168.1.33 inside

    dhcpd lease 3600

    dhcpd ping_timeout 750

    dhcpd outside auto_config

    dhcpd allow inside

    Terminal width 80

    Cryptochecksum:xxxx

    ****************

    The DNS server is the one assigned to me by my ISP.

    My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5

    "isakmp nat-traversal 20" can do the trick.

  • Reseting ipsec on PIX 501

    Hi all. Just a quick question. I can't seem to find how to reset ipsec on PIX 501 and force her to negotiate again and I also want to reset statistics for ipsec his. I know that I saw somewhere, orders, but now can't seem to find the commands from anywhere.

    Thanks in advance for any help.

    Hello...

    Config mode...

    ISAKMP crypto claire his

    - and -

    clear crypto ipsec his

    PS. You can find the commands on the PIX by entering the configuration mode by typing...

    PIX01 (config) # clear cry?

    Hope the above helps and please note messages!

  • PIX 501 will ios ver 6.2 come to him, with only 16ram 8flash? Thank you

    Wanted to load pdm 2.1.1 firewall and VPN. Found 501 takes ver 6.2 but not to enother ram.

    Thank you

    Phil

    From http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_62/relnotes/pixrn622.htm#xtocid4 :

    "The PIX 501 has 16 MB of RAM and will work correctly with Version 6.2, while all other PIX firewall platforms continue to require at least 32 MB of RAM (and are therefore also compatible with Version 6.2 or newer).

    In addition, all units except the PIX 501 and PIX 506/506E require 16 MB of Flash memory to boot. (The 501 PIX and PIX 506/506E have 8 MB of Flash memory, which works correctly with Version 6.2) »

    PIX firewall model... Flash memory required in point 6.2

    PIX 501 .......................... 8 MB

    Steve

  • Place a FIOS for VPN router behind PIX 501

    I have a Verizon FIOS internet connection and one of their routers wide wireless broadband, and this is a configuration of base completely... their router DHCP and firewalls, and the connection has a dynamic address.  I would put the PIX 501 behind the Verizon router as one of its clients and make the VPN PIX of other PIX 501 at other locations, such as my entire network has access to remote networks.

    Is this possible, and if yes, any who could some suggest configurations (how to address internal and external, static routes ports that may be required somewhere, etc.)?

    Thanks for any help.

    When installing my FiOS, I had already asked that it be installed on the Ethernet cable. Don't know they need to do something for you to spend the coax to Ethernet.

    The best way to test it would be to find the Media Converter (follow the coaxial cable between your FiOS router to the demarc and there should be a box with a coaxial port, some phone Sockets and an Ethernet port). If you unplug the coaxial cable and plug a laptop computer on the Ethernet port, see if your laptop takes a public IP address. If Yes, then you just have to run to your PIX501 Ethernet cable and you should be ready.

    Just to note that Verizon, according to your region, reserved DHCP assignments. This means that you may need to call Verizon and ask them to release the previous assignment of DHCP-MAC addresses. I had this happen recently. They must release the assignment then your PIX will pull a new IP address and they will book your new IP - MAC address assignment. They do this to speed up the connection to a cold start time on the router.

    Basically, they are filtering by MAC address, but rather through a sticky ARP where they clear the entry, and then the next device that connects records his MAC address and then only that device is permitted to connect to this leg of the cable. So there is a bit of work you have to do, but the most difficult part would be sitting on hold waiting for a tech, if you call to Verizon.

  • sick of frustration... 501 and ACL

    Hey all, what gives.

    I worked on a pix 501 and I can't get the ACL to save my life. I'm new on this and obviously missing something. I have a 501 connected to a cable broadband account is public ip through DHCP. I want to limit all traffic going out to 80, 110 and 53.

    I add the following commands.

    access-l 125 permit tcp any any eq 80

    access-l 125 permit tcp any any eq 53

    access-l 125 permit tcp any any eq 110

    access-l 125 deny ip any one

    access-g 125 in interface inside

    everything falls to the interface I think. I am able to browse the net, Kazaa, sof2 throughout the day if I use the default configuration provided by the firewall. I posted this before and actually got it to work once. I tried to repeat the process, but failed.

    any help is GREATLY appreciated

    humbly yours

    MB

    Add

    > access-l 125 permit udp any how any eq 53

    DNS searches with UDP, TCP not. You will find probably your DNS resolution does not work, so when you navigate to a web server by name it will fail, because the first thing that your PC will do is a name search.

Maybe you are looking for

  • PSC 1315, not paper feeding

    recently reinstalled my psc 1315 and installed new ink cartridges.  It is "sounds of printing", but the paper does not feed.

  • How to play episodes I bought on iTunes?

    Hi all I recently bought an entire season of a series, and whenever I try to play the first episode it is not working properly. I don't know how to actually play the entire episode and whenever I click on it, he plays just 30 second clip, a preview.

  • The FEP Server alert notifications do not display the correct time zone

    Time stamps FEP report When I receive my FEP Server alert notifications timestamps are far away. Nobody knows how to set the correct time zone, so the report will be accurate?  I think that the default time is UTC.

  • Decommissioning of Windows 10

    I have recently switch to window 10 and I saw the problem of blue screen every time I do something so I downgrade to my original window and I discovered that my product key is not more authenticcan I know how to fix this problem?

  • I can't create partitions in unallocated space when trying to install Windows.

    problem installing Windows I tried to install windows 7, then the hard drive selection window, it shows 2 spaces unallocated and I can't delete or create a new partition of them and niether I am able to install windows .please help