PIX 501 - VPN - based

Similar Questions

• Adding a pix 501 VPN 2

  Hello.. I am beginner in this kind of things cisco...

  I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...

  Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:

  Outside_map map (ERR) crypto set peer 200.20.10.3

  WARNING: This encryption card is incomplete

  To remedy the situation even and a list of valid to add this encryption card

  Hi garcia

  for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...

  for configuration, you can go through the URL below... It has all the details on IPSEC config:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• Customer Cisco PIX 501 VPN connects but no connection to the local network

  Hi all:

  I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.

  I have attached the PIX configuration.

  Advice will be greatly appreciated.

  ********************

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxxx

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool ippool 192.168.2.1 - 192.168.2.5

  location of PDM 192.168.2.0 255.255.255.0 outside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup vpn3000 ippool address pool

  vpngroup vpn3000 Server dns 68.87.72.130

  vpngroup vpn3000-wins 192.168.1.100 Server

  vpngroup vpn3000 split tunnel 101

  vpngroup vpn3000 downtime 1800

  password vpngroup vpn3000 *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:xxxx

  ****************

  The DNS server is the one assigned to me by my ISP.

  My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5

  "isakmp nat-traversal 20" can do the trick.

• pix 501 vpn problem

  Can connect, I see not all network resources.

  The Vpn Client, worm: 5.0.01, is running on an xp machine.

  It connects to the network is behind a 6.3 (5) pix501-worm.

  When the connection is established the remote client gets an address assigned to the pool 192.168.2.10 vpn - 192.168.2.25:

  The vpn client log shows:

  Line: 45 18:07:27.898 12/08/09 Sev = Info/4 CM / 0 x 63100034

  The virtual card has been activated:

  IP=192.168.2.10/255.255.255.0

  DNS = 0.0.0.0 0.0.0.0

  WINS = 0.0.0.0 0.0.0.0

  Area =

  Split = DNS names

  It is followed by these lines:

  46 18:07:27.968 12/08/09 Sev = WARNING/2 CVPND/0xE3400013

  AddRoute cannot add a route: code 87

  Destination 192.168.1.255

  Subnet mask 255.255.255.255

  Gateway 192.168.2.1

  Interface 192.168.2.10

  47 18:07:27.968 12/08/09 Sev = WARNING/2 CM/0xA3100024

  Failed to add the route. Network: c0a801ff, subnet mask: ffffffff, Interface: c0a8020a Gateway: c0a80201.

  48 18:07:28.178 12/08/09 Sev = Info/4 CM / 0 x 63100038

  Were saved successfully road to file changes.

  49 18:07:28.198 12/08/09 Sev = Info/6 CM / 0 x 63100036

  The routing table has been updated for the virtual card

  50 18:07:29.760 12/08/09 Sev = Info/4 CM/0x6310001A

  A secure connection established

  * ...

  I can ping the remote client, on an inside ip behind the same pix

  When I get the 'route add failure' above, but I cannot ping the computer name.

  I activated traversal of NAT using the PDM, but when I connect with this option, I get the error that the "remote endpoint is NOT behind a NAT device this end is behind a NAT device" and ping fails.

  Behind the pix are a few computers with no central server, so I'm failed a WINS server for remote clients.

  I created the vpn with the wizard.

  The configuration file is attached.

  Any suggestion would be appreciated.

  Kind regards

  Hugh

  Hugh, sure you can classify based on the whole conversation, but you don't have to do but be certainly provide assessments.

  To sum up the shrinking global problems, the main objective was to ensure configuration VPN RA on the PIX501 has been corrected.

  1. we have enabled NAT - T on the firewall - even if it wasn't the question, but need it either it should you RA other places - travseral NAT VPN sensitizes the firewall on the other ends NAT devices - here is some good information on NAT - T for reference in the future

  http://www.Microsoft.com/technet/community/columns/cableguy/cg0802.mspx

  2. we fixed the VPN-POOL/28 network as well as the access list and acl to be coherent crypto sheep.

  Here is a link for future reference with many PIX configuration scenarios

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/prod_configuration_examples_list.html

  Finally, your only question remaining, we can say is purely isolated with the customer software vpn and MAC machine.

  You could maybe try a different version of the client in the MAC, or also look at the release notes for the open caveats to avoid cisco cleint managing versions and MAC versions if there are problems.

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/prod_release_notes_list.html

  Concerning

• PIX 501 VPN

  Hi, I just got my PIX configured based on the clear capability statement, I got one of you this morning. Now, I'm trying to set up the VPN, I looked at the Cisco site (http://cisco.com/en/US/products/hw/vpndevc/ps2030/prod_configuration_examples_list.html#anchor14) but could not understand that we need to follow. Could you please send me the instruction or the link to configure vpn? Also, I don't have the vpn client to test my vpn, how what to do? As you can understand my question, I am new to cisco gear... Thank you.

  Hello

  I'm guessing that you need one of these two virtual private networks.

  -Remote access VPN: where remote allows the Cisco VPN client users to access the resources of the company

  -Site to site VPN: where two systems with IPSEC support establish a VPN tunnel, allowing the internal LAN from different termination points (offices) communicate.

  You can find these two examples on the url you gave.

  If the remote access, I'd watch

  http://Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702992.shtml

  And then also look at how to set up the split tunneling, then the home user can access the resources of the business AND Internet.

  For the site to site VPN, it depends if your device is a PIX / ASA or a router.

  It will be useful,

  Paulo

• PIX 501 & VPN Client unable to ping or encrypt traffic?

  I'm new and I work on my CCNA. I have a Setup pix behind a dsl with NAT router that I can not turn off. I create a pin hole for IPSec traffic to port 500 to my pix off if. I can connect correctly the Client VPN software. I think I establish an IKE and IPSec tunnel very well. I used the wizard to configure the VPN. I have a pool dhcp which issues an IP address correctly, and user group with set password. There is no site-to-site VPN, the network is a network of peers without any DNS or WINS server on the local network. I'm lost, frustrated and tired of 45 minutes of driving on this site whenever I want to try to set up a new configuration. It is essentially a off the pix of the box. There not here all configurations at all really. Here is my config.

  6.3 (1) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password * encrypted

  passwd * encrypted

  hostname pix

  domain ciscopix.com

  clock timezone CST - 6

  clock to summer time recurring CDT

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  names of

  inside_outbound_nat0_acl ip access list allow any 10.10.10.0 255.255.255.240

  outside_cryptomap_dyn_20 ip access list allow any 10.10.10.0 255.255.255.240

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  reset the IP audit attack alarm drop action

  IP local pool pool1 10.10.10.1 - 10.10.10.10

  location of PDM 192.168.12.0 255.255.255.240 outside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 20

  ISAKMP policy 20 3des encryption

  ISAKMP policy 20 md5 hash

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  vpngroup address pool1 pool test

  vpngroup test 1800 idle time

  test vpngroup password *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 15

  VPDN allow outside

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  exec banner prohibited unauthorized access

  connection of the banner prohibited unauthorized access

  Banner motd prohibits unauthorized access

  Cryptochecksum:xxx

  : end

  Thank you...

  Hi gkotlin

  mark the request as a problem solved, so that its not seen by others. The rate of the position, if deemed useful... Thank you

• Pix 501 VPN no internet Assistant

  Via the VPN right front

  The VPN remote access

  Cisco-Client 3.x or later version

  Group & pre-shared key (no cert)

  EECA, Local

  Pool configured VPN

  .. all the standard stuff.

  I can connect but I can't access the internet.

  Issues related to the:

  Why can I not see my network server? I can sort of map a drive by typing in the folder \\myserve\shared

  Why I can't go on the internet when connected to the VPN?

  5.0.07.0410 VPN client

  PDM 3.0.4

  PIX 6.3.5

  Thank you

  Yes, you can change it.

  By the way, here is a good link to MS:

  Troubleshooting the Network Neighborhood from Microsoft after establishing a VPN Tunnel with the Cisco VPN Client

  HTH.

  Portu.

• PAT on IPSEC VPN (Pix 501)

  Hello

  I work to connect a PIX 501 VPN for a 3rd party hub 3015. The hub requires all traffic to come from a single source IP address. This IP address is assigned to me as z.z.z.z. I have successfully built the VPN and tested by mapping staticly internal IP with the IP address assigned, but cannot get the orders right to do with PAT in order to have more than one computer on the subnet 10.x.x.0. This Pix is also a backup for internet routing and NAT work currently as well for this.

  I can redirect traffic to my subnet to the remote subnet via the VPN, but I can't seem to get the right stuff PAT to the VPN using the assigned IP address. If anyone can give me some advice that would be great.

  lines of current config interesting configuration with static mapping:

  --------------------------------------------------------------------------

  access-list 101 permit ip 10.0.0.0 255.255.255.0 y.y.y.0 255.255.255.0

  access-list 102 permit ip y.y.y.0 255.255.255.0 z.z.z.z host

  access-list 103 allow host ip y.y.y.0 255.255.255.0 z.z.z.z

  IP address outside w.w.w.1 255.255.255.248

  IP address inside 10.0.0.1 255.255.255.0

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  public static z.z.z.z (Interior, exterior) 10.x.x.50 netmask 255.255.255.255 0 0

  Route outside 0.0.0.0 0.0.0.0 w.w.w.2 1

  correspondence address card crypto mymap 10 103

  mymap outside crypto map interface

  ISAKMP allows outside

  Thank you!

  Dave

  Dave,

  (1) get rid of static electricity. Use more Global/NAT. The static method will create a permanent

  translation for your guests inside and they will always be this way natted. Use

  NAT of politics, on the contrary, as shown here:

  not static (inside, outside) z.z.z.z 10.x.x.50 netmask 255.255.255.255 0 0

  Global (outside) 2 z.z.z.z netmask 255.255.255.255

  (Inside) NAT 2-list of access 101

  (2) the statement, "nat (inside) access 0 2' list will prevent nat of your valuable traffic."

  Delete this because you need to nat 2 nat/global card. (as a general rule, simply you

  If you terminate VPN clients on your device and do not want inside the traffic which

  is intended for the vpn clients to be natted on the external interface).

  (3) with the instructions of Global/nat 2, all traffic destined for the remote network will be first

  translated into z.z.z.z. Then your card crypto using the ACL 103 will encrypt all traffic which

  sources of z.z.z.z for y.y.y.0 24. This translation wil happen only when traffic is destined for the vpn.

  I hope this helps. I have this work on many tunnels as you describe.

  Jamison

• Help with vpn pix 501

  I'm setting up a cisco pix 501 vpn tunnel but will have questions. The Firewall works although I am able to get out of the internet, but the VPN does not work. On the primary side, I see that the tunnel is up and the traffic is sent but not received.

  Currently I'm sitting at the secondary location but don't know what the problem maybe. Anyone know what I have wrong which could prevent the data to send from this device?

  Here is my config

  Here's my config if it would help

  See the race
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 2KFQnbNIdI.2KYOU encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  hostname ciscofirewall
  domain hillsanddales.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 5
  fixup protocol rtsp 55
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25

  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list 101 permit ip 192.168.80.0 255.255.255.0 192.168.50.0 255.255.255.0
  192.168.80.0 IP Access-list sheep 255.255.255.0 allow 192.168.50.0 255.255.255.0
  in_outside list access permit tcp any host 192.168.50.240
  in_outside list access permit tcp any host 64.90.xxx.xx
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside 66.84.xxx.xx 255.255.255.252
  IP address inside 192.168.80.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  location of PDM 192.168.50.0 255.255.255.0 outside
  location of PDM 192.168.80.2 255.255.255.255 inside
  location of PDM 192.168.50.0 255.255.255.0 inside
  location of PDM 182.168.80.0 255.255.255.255 inside
  location of PDM 0.0.0.0 255.255.255.0 inside
  location of PDM 0.0.0.0 255.255.255.255 inside
  location of PDM 192.168.80.5 255.255.255.255 inside
  location of PDM 192.168.80.7 255.255.255.255 inside
  PDM logging 100 information
  history of PDM activate

  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Route outside 0.0.0.0 0.0.0.0 66.84.xxx.x
  Route inside 192.168.50.0 255.255.255.0 192.168.50.240 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.80.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  <--- more="" ---="">

  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp-3des esp-md5-hmac aptset
  aptmap 10 ipsec-isakmp crypto map
  correspondence address card crypto aptmap 10 101
  card crypto aptmap 10 peers set 64.90.xxx.xx
  card crypto aptmap 10 transform-set aptset
  aptmap interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address 64.90.xxx.xx netmask 255.255.255.255
  ISAKMP identity address
  ISAKMP nat-traversal 20
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 md5 hash
  10 2 ISAKMP policy group
  ISAKMP life duration strategy 10 86400
  Telnet 192.168.80.2 255.255.255.255 inside
  Telnet 182.168.80.0 255.255.255.255 inside
  Telnet 192.168.80.5 255.255.255.255 inside
  Telnet 192.168.80.0 255.255.255.0 inside
  Telnet 192.168.80.7 255.255.255.255 inside
  Telnet timeout 5
  SSH timeout 5
  management-access inside

  Console timeout 0
  dhcpd address 192.168.80.2 - 192.168.80.33 inside
  dhcpd dns 64.90.xxx.xx 64.90.xxx.xx
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:01532689fac9491fae8f86e91e2bd4c0
  : end

  Hello

  At least the NAT0 ACL is not in use

  You should have this added to the configuration

  NAT (inside) 0 access-list sheep

  -Jouni

• VPN with PIX 501

  Help!

  I'm trying to set up VPN on my PIX 501. I have no experience of the PIX and have no idea where to start!

  Any help will be greatly appreciated.

  Thank you

  Bennie

  access list allow accord a

  where is the name of the access list that you applied the entrants to your external interface. You may also allow accord coming out, if you have a list of incoming configured access to your inside interface.

• Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.

  I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.

  .

  The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).

  .

  A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?

  .

  I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?

  .

  Thank you.

  UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.

  The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.

• L2l IPSec VPN 3000 and PIX 501

  Hello

  I have a remote site that has a broadband internet connection and uses a PIX 501.  We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.

  I followed the following documentation:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml#tshoot

  However the L2L session does not appear on the hub when I check the active sessions.

  The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.

  Any help or advice are appreciated.

  I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.

  For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.

  Here is an example of sample config

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

  I hope this helps!

• PIX 501 for Cisco 3640 VPN router

  -Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-

  Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.

  What Miss me? I added the configuration for the PIX and the router.

  Here are the PIX config:

  PIX Version 6.1 (1)

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable encrypted password xxxxxxxxxxxxxxxx

  xxxxxxxxxxxxx encrypted passwd

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  Telnet timeout 5

  SSH timeout 5

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXXXXXXXXXXXXXXXX

  : end

  Here is the router config

  Router #sh runn

  Building configuration...

  Current configuration: 6500 bytes

  !

  version 12.2

  no service button

  tcp KeepAlive-component snap-in service

  a tcp-KeepAlive-quick service

  horodateurs service debug datetime localtime

  Log service timestamps datetime localtime

  no password encryption service

  !

  router host name

  !

  start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system

  queue logging limit 100

  activate the password xxxxxxxxxxxxxxxxx

  !

  clock TimeZone Central - 6

  clock summer-time recurring CENTRAL

  IP subnet zero

  no ip source route

  !

  !

  no ip domain-lookup

  !

  no ip bootp Server

  inspect the name smtp Internet IP

  inspect the name Internet ftp IP

  inspect the name Internet tftp IP

  inspect the IP udp Internet name

  inspect the tcp IP Internet name

  inspect the name DMZ smtp IP

  inspect the name ftp DMZ IP

  inspect the name DMZ tftp IP

  inspect the name DMZ udp IP

  inspect the name DMZ tcp IP

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 20

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx

  ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test

  Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT

  !

  dynamic-map crypto dny - Sai 25

  game of transformation-PIXRMT

  match static address PIX1

  !

  !

  static-card 10 map ipsec-isakmp crypto

  the value of x.x.180.133 peer

  the transform-set vpn-test value

  match static address of Hunt

  !

  map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc

  !

  call the rsvp-sync

  !

  !

  !

  controller T1 0/0

  framing ESF

  linecode b8zs

  Slots 1-12 channels-group 0 64 speed

  Description controller to the remote frame relay

  !

  controller T1 0/1

  framing ESF

  linecode b8zs

  Timeslots 1-24 of channel-group 0 64 speed

  Description controller for internet link SBIS

  !

  interface Serial0/0:0

  Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites

  bandwidth 768

  no ip address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  encapsulation frame-relay

  frame-relay lmi-type ansi

  !

  interface Serial0 / point to point 0:0.17

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 17 frame relay interface

  !

  interface Serial0 / point to point 0:0.18

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 18 frame relay interface

  !

  interface Serial0 / point to point 0:0.19

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 19 frame relay interface

  !

  interface Serial0 / point to point 0:0.20

  Description Frame Relay to xxxxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 20 frame relay interface

  !

  interface Serial0 / point to point 0:0.21

  Description Frame Relay to xxxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 21 frame relay interface

  !

  interface Serial0 / point to point 0:0.101

  Description Frame Relay to xxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 101 frame relay interface

  !

  interface Serial0/1:0

  CKT ID 14.HCGS.785383 T1 to ITT description

  bandwidth 1536

  IP address x.x.76.14 255.255.255.252

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  NAT outside IP

  inspect the Internet IP on

  no ip route cache

  card crypto ISCMAP

  !

  interface Ethernet1/0

  IP 10.1.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  interface Ethernet2/0

  IP 10.100.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  router RIP

  10.0.0.0 network

  network 192.168.1.0

  !

  IP nat inside source list 112 interface Serial0/1: 0 overload

  IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible

  IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible

  IP nat inside source 10.1.3.2 static 209.184.71.140

  IP nat inside source static 10.1.3.6 209.184.71.139

  IP nat inside source static 10.1.3.8 209.184.71.136

  IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible

  IP classless

  IP route 0.0.0.0 0.0.0.0 x.x.76.13

  IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19

  IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18

  IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17

  IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20

  IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21

  IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101

  no ip address of the http server

  !

  !

  PIX1 static extended IP access list

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  IP access-list extended hunting-static

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  extended IP access vpn-static list

  ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255

  access-list 1 refuse 10.0.0.0 0.255.255.255

  access-list 1 permit one

  access-list 12 refuse 10.1.3.2

  access-list 12 allow 10.1.0.0 0.0.255.255

  access-list 12 allow 10.2.0.0 0.0.255.255

  access-list 12 allow 10.3.0.0 0.0.255.255

  access-list 12 allow 10.4.0.0 0.0.255.255

  access-list 12 allow 10.5.0.0 0.0.255.255

  access-list 12 allow 10.6.0.0 0.0.255.255

  access-list 12 allow 10.7.0.0 0.0.255.255

  access-list 112 deny ip host 10.1.3.2 everything

  access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255

  access-list 112 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.2.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.3.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.4.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.5.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.6.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.7.0.0 0.0.255.255 everything

  access-list 120 allow ip host 10.100.1.10 10.1.3.7

  not run cdp

  !

  Dial-peer cor custom

  !

  !

  !

  !

  connection of the banner ^ CCC

  ******************************************************************

  WARNING - Unauthorized USE strictly PROHIBITED!

  ******************************************************************

  ^ C

  !

  Line con 0

  line to 0

  password xxxxxxxxxxxx

  local connection

  Modem InOut

  StopBits 1

  FlowControl hardware

  line vty 0 4

  exec-timeout 15 0

  password xxxxxxxxxxxxxx

  opening of session

  !

  end

  Router #.

  Add the following to the PIX:

  > permitted connection ipsec sysopt

  This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.

• VPN between cisco unified customer 3.6.3 and Pix 501 6.2 (1) with the MS CA server

  Hello

  I have Microsoft CA server with the latest support CEP and pix 501 that gets the digital certificate. I also have the client certificate of Cisco, but VPN doesn't work

  In the IPSec Log Viewer, I constantly "CM_IKE_ESTABLISH_FAIL."

  It worked well prior to Win2k server has been completely updated with the latest patches.

  The pix configuration is identical to that of article http://www.cisco.com/warp/public/471/configipsecsmart.html

  I reinstall the stand-alone CA and support CEP server but not had any luck.

  What could be wrong?

  It looks like IKE implementation problem. Make DH group 2 policy ISAKMP.

  Visit this link:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_v53/IPSec/exvpncl.htm

• Place a FIOS for VPN router behind PIX 501

  I have a Verizon FIOS internet connection and one of their routers wide wireless broadband, and this is a configuration of base completely... their router DHCP and firewalls, and the connection has a dynamic address.  I would put the PIX 501 behind the Verizon router as one of its clients and make the VPN PIX of other PIX 501 at other locations, such as my entire network has access to remote networks.

  Is this possible, and if yes, any who could some suggest configurations (how to address internal and external, static routes ports that may be required somewhere, etc.)?

  Thanks for any help.

  When installing my FiOS, I had already asked that it be installed on the Ethernet cable. Don't know they need to do something for you to spend the coax to Ethernet.

  The best way to test it would be to find the Media Converter (follow the coaxial cable between your FiOS router to the demarc and there should be a box with a coaxial port, some phone Sockets and an Ethernet port). If you unplug the coaxial cable and plug a laptop computer on the Ethernet port, see if your laptop takes a public IP address. If Yes, then you just have to run to your PIX501 Ethernet cable and you should be ready.

  Just to note that Verizon, according to your region, reserved DHCP assignments. This means that you may need to call Verizon and ask them to release the previous assignment of DHCP-MAC addresses. I had this happen recently. They must release the assignment then your PIX will pull a new IP address and they will book your new IP - MAC address assignment. They do this to speed up the connection to a cold start time on the router.

  Basically, they are filtering by MAC address, but rather through a sticky ARP where they clear the entry, and then the next device that connects records his MAC address and then only that device is permitted to connect to this leg of the cable. So there is a bit of work you have to do, but the most difficult part would be sitting on hold waiting for a tech, if you call to Verizon.