PIX firewall Image issue

Similar Questions

• Access list ID # on a PIX firewall

  Is anyone know what of the identifier access list on a pix firewall?

  Standard IOS = 1-99

  Extended IOS is 100-199.

  SW = PIX?

  There is no "limit" by Word to say in the Pix. These limits are in IOS because they define what 'type' of acl, it's IE APPLETALK, IPX, IP etc etc. Pix IP is therefore not necessary for this type of identification.

  access-list 100000000000000; 1 items

  allow line of the access list 1 100000000000000 ip any a (hitcnt = 0)

  Jason

• Cisco ACS and Pix Firewall

  I have configured the aaa authentication in the pix firewall to see the ACS RADIUS Server for verification of the user. If the ACS server becomes unavailable, then I could not connet the pix firewall.

  In the router, I have the configuration option

  AAA authentication login default group Ganymede + local

  that tells the router first looking for a radius server and if is not available connect through the local database.

  Is there an option in the Cisco pix firewall to connect using local information if ACS is not available?

  Thanks in advance

  Hello

  PIX back up method to entered the unit in the event of server failure aaa works on 6.3.4 code and above. In the codes plus late 6.3.4 If the RADIUS server fails it is impossible to get in unless password recovery. "However if we have not configured for console aaa authentication than user name: pix and password: cisco" works by default.

  Kind regards

  Mahmoud Singh

• PIX firewall problem

  I have two servers, one in pix inside and the other in the demilitarized zone. I wanted to set them up so that they can communicate with routers and switches

  Located outside the pix firewall.

  My inner Server works fine, able to go Internet and able to comminicate with all devices located outside the Pix Firewall. Here is reference configuration

  of insideserver.

  outside_acl list extended access allowed host x.223.188.0 255.255.255.0 172.28.32.50 ip

  outside_acl list extended access permit ip host host x.219.212.217 172.28.32.50

  access-list extended sheep permit ip host 172.28.32.50 host x.219.212.217

  access-list extended sheep permit ip host 172.28.32.50 x.223.188.0 255.255.255.0

  inside_acl list extended access permit ip host 172.28.32.50 all

  But my DMZ server does not work. However, I made the same configuration with respect to the server on the inside. Not able to communicate with outside DMZ server

  network.

  outside_acl list extended access allowed host x.223.188.0 255.255.255.0 172.28.92.72 ip

  outside_acl list extended access permit ip host host x.219.212.217 172.28.92.72

  access-list extended sheep permit ip host 172.28.92.72 host x.219.212.217

  access-list extended sheep permit ip host 172.28.92.72 x.223.188.0 255.255.255.0

  dmz_acl list extended access permit ip host 172.28.92.72 all

  If I create a static entry for your DMZ SNMP server.

  static (edn, external) 172.28.92.72 172.28.92.72 netmask 255.255.255.255

  He starts to communicate with external devices, but stops Internet run on this server. same configuration

  works with the server on the inside, but not with dmz server.

  NAT (inside) 0 access-list sheep

  NAT (inside) 3 172.28.32.0 255.255.255.0

  NAT (dmz) 3 172.28.92.0 255.255.255.0

  Global interface 3 (external)

  Your static entry is bypassing your nat (dmz) 3 entry. You can do NAT exemption instead, as you do to your home

  1. remove the static entry (followed by clear xlate)

  Add - nat 0 access-list sheep (dmz)

  I suggest to use two acl different sheep, one for each interface.

  Ex: nonat_inside

  nonat_dmz

• PIX firewall software

  Hi guys,.

  I am looking to download IOS ver 4,0000 for PIX 515E, but can't seem to find anywhere in the downloads/security section. The only version they have is 8.0.4.

  Anyone know where I could find all earlier versions?

  Thank you very much

  Elena

  Elena, when you go to download box, choose any version 8.0, then window right side you will see a text saying previous software release click on this hyperlink and it will take you to all versions including 7.x

  http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=8.0.4&mdfid=277072390&sftType=PIX+Firewall+Software&optPlat=&nodecount=2&edesignator=ED&modelName=Cisco+PIX+515E+Security+Appliance&treeMdfId=268438162&treeName=Security&modifmdfid=&imname=&hybrid=Y&imst=N&lr=Y

  but here's the direct link

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX

  Concerning

• Allowing L2TP to pass through PIX Firewall

  Hi all

  Can someone help me on how to allow inbound l2tp connection on a pix? Behind the pix firewall, there is an ISA server as a vpn l2tp server. I can't allow l2tp on the pix.

  Thank you very much!

  Please use this doc as a guide-

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080094a5a.shtml

  Jon

• How can I clear counters access-list on a pix firewall

  How can I erase the hitcounts on an on a pix firewall access list without resetting the pix?

  It would be clear access-list on a router counters.

  Thanks in advance

  Steve

  access list counters Clear

• To block P2P traffic on the PIX firewall

  What will be the mechanism, and how we can block the traffic of P2P applications like eDonkey, KaZaa and Imesh etc on the PIX firewall.

  Hello

  You can find the info here:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_tech_note09186a00801e419a.shtml

  I hope this helps.

  Jay

• PIX firewall vpn Sonicwall

  Hello.

  My question is this.

  It is possible to establish a VPN between a PIX Firewall and Sonicwall firewall?.

  To be like that, where I can find documentation on the matter?

  Thanks in advance.

  Dear.

  Both Sonicwall conforms to standards, which they do, then Yes, you can create a VPN between them.

  I don't think we have PIX, Sonicwall example config specifically, but the config on the PIX is still pretty standard, no matter what you connect to.

  SonicWALL has an example here: ftp://ftp.sonicwall.com/pub/info/vpn/CiscoPIX.pdf

• How to limit the ICMP on the PIX firewall.

  Guys good day!

  I have a dilemma with regard to limiting ICMP users browsing to other networks such as other demilitarized interns.

  I know that, to allow ICMP to pass through interfaces, you will need to create an ACL such as below:

  access-list DMZACL allow icmp a whole

  Users require this config ping a server on the DMZ, but it is a security risk.

  To minimize, I have a group of objects created in order to identify hosts and networks is allowed to have access to the echo-replies.

  Again, this is a problem since many host who extended pings just to monitor the connectivity server and its application.

  Do you have other ideas guys?

  As to limiting the echo answers on the PIX. As first 5 echo request succeed with 5 echo-replies and the rest would be removed.

  This could be done?

  Thank you

  Chris

  Hello.. I don't think you can do this by using an ACL on the PIX, however, you might be able to stop the ICMP sweeps by activating CODES signatures using the check ip command you... For more information see the link below

  Guidelines of use Cisco Intrusion Detection System (IDS Cisco) provides the following for IP-based systems:

  ? Audit of traffic. The application of signatures will be audited only as part of an active session.

  ? Apply to the verification of an interface.

  ? Supports different auditing policies. Traffic that matches a signature triggers a range of configurable

  actions.

  ? Disables signature verification.

  ? Always turns the shares of a class of signature and allows IDS (information, attack).

  The audit is performed by looking at IP packets to their arrival at an input interface, if a packet triggers

  a signature and the action configured does not have the package, and then the same package may trigger another

  signatures.

  Firewall PIX supports inbound and outbound audit.

  For a complete list signatures of Cisco IDS supported, their wording and whether they are attacking or

  informational messages, see Messages in Log System Cisco PIX Firewall.

  See the User Guide for the Cisco Secure Intrusion Detection System Version 2.2.1 for more information

  on each signature. You can view the? NSDB and Signatures? Chapter of this guide at the following

  website:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids1/csidsug/SIGs.htm

• Place a server behind a PIX firewall production

  Hi all

  We currently have a web server that is connected to the Internet directly (multiple addressable IPs belonging to 5 different ranges of class C, with a soft firewall).

  There are several Web sites, some of them with their own IP addresses, some of them sharing IPs with other sites.

  We intend to put a server behind a PIX firewall and convert addressable IP addresses to private IPs with the static mapping on the PIX.

  We plan use a PIX with two (2) interfaces.

  You think it of feasible or are there things that I'm on?

  Some things I'm not sure about:

  Since there are several C class IPs assigned to the server and therefore 5 gateways defined on a NIC, one for each class, how that is defined on the PIX? 5 separate roads or...?

  We need to use a kind of "virtual interfaces", one for each class C subnet?

  This is an example of a "final product":

  Web request to the 204.xxx.85.10 IP addressable would be directed to the private IP address: 10.xxx.85.10.

  Web request to the 204.xxx.86.10 IP addressable would go to 10.xxx.86.10 etc etc.

  Any help you could provide in this regard will be GREATLY apprechiated!

  Hello

  Please provide a topology (plain text would work). I can't tell from your description, if you have a perimeter router in front of the Pix. In addition, when you write statements of static road on the Pix, you must include an interface as follows

  Route if_name IPAddress netmask gateway_ip

  Once you post this information, I'll take another reading to better understand your situation.

  Thank you

• Username in the Pix Firewall

  When I do a command 'See logging' in my Cisco Pix Firewall (6.3), I am able to see the message below

  605005: x.x.x.x/33652 for eth1:y.y.y.y/telnet for the user authorized login «»

  In the message above, why the user name is not printed?

  your config has.

  Console telnet AAA authentication GANYMEDE + | RAY | LOCAL '?

• PIX firewall Security Guide

  Hi guys, I noticed that there is a document on the setting of the Cisco routers on cisco.com

  Is there than a best practices similar document type for Secure PIX firewall? or even a general firewall best practices guides?

  I searched, but did not really find anything. Any help would be great!

  Hi Nathan,

  So far, there is no specific doc, but you can get the idea of documentation PIX / ASA itself. This is probably due to the nature 'trust' of the firewall itself (everybody knows that it was not 100% sure).

  Anyway, there is a document on "Best practices of firewall" at http://www.principlelogic.com.

  Others are:

  http://www.Security.FSU.edu/firewall.cfm

  http://SearchSecurity.TechTarget.com/originalContent/0, 289142, sid14_gci838230, 00.html

  Personally, I think the recommendations are very good and can be applied generally to fix most of the firewall products.

  I hope this helps.

  Rgds,

  AK

  WARNING: -.

  The post above is not intended to promote the services/tools/products on behalf of a person or organizations. This is simply about & information sharing.

• Issue of ARP and PIX firewall

  I have a PIX 515, which is the static NAT translations (using the static entries and alias). I have a remote access server running Citrix. We had some problems connecting to this server internally. I found that when I ping, 9 out of ten trials is expires after the first attempt. When I do a "arp / has" my workstation it is back with the MAC address of the internal interface of my PIX. If I try to ping and manually, disable my arp cache after ten or more attempts is correctly will ping the right device - and then go immediately to the MAC of PIX address. This configuration is a fairly standard for us. What could be wrong?

  Looks like the PIX meets MAC address ARP queries the Citrix servers. Turn off the proxy ARP on the PIX inside interface with:

  > sysopt noproxyarp inside

• Recording of images issues

  Hi all

  I am new to Java, Blackberry and Eclipse so please forgive my lack of knowledge on what may be the simple understanding.  I have just a few little random basic questions.

  I use Eclipse with the JDE 4.7 plugin and development for the storm.  I use the Simulator for development.

  I was instructed to write an application that needs to record 2 different pieces of information.  The application must save an array of bool, so it can be accessed on the next time the application is loaded.   For this method, I use persitant store.

  First question:

  Persistent would consider a good method, or should I be save this data in another case?

  Now on the my main concern.  Our application has a bunch of files for a game. After that part of the game is finished, we want the user to then be able to take a picture of the game and store it on the phone so that the user can then select as wallpaper.

  For this method, I've been through a code and I promise you, I searched high and low and have not found a solution that I understand very well.

  I noticed people using a "connector" to open a path to the file system/or create it.  However, I am having a hard time understanding how the Simulator affects its filepath and how the real phone its filepath.

  If someone could help point me in the right direction on how to save a file of our application on the phone, so it can be used as wallpaper, I would be very happy.

  Here's a piece of how I'm saving my code.  I get an exc of IO.  But for an IO exc references claim that the firewall does not allow a connection.  I'm not connect through a firewall, then, how is this possible?

  m_filename = the path to a file in our application.

  The code in bold is were the exception is thrown.

  Thank you in advance for anyone of help.

  Bitmap _bitmap = Bitmap.getBitmapResource(m_filename);PNGEncodedImage _pngEncodedImage = PNGEncodedImage.encode(_bitmap);
  
  try{    String fileDir = System.getProperty("fileconn.dir.memorycard");    if (fileDir == null)    {  Dialog.alert("ERROR:  fileDir = null");    }    else    }        Dialog.alert("fileDir = " + fileDir);    }    FileConnection fc = (FileConnection)    Connector.open( fileDir + m_filename,Connector.READ_WRITE);
  
      if(!fc.exists())    fc.create();    OutputStream oStream = fc.openOutputStream();    oStream.write(_pngEncodedImage.getData());    oStream.flush();    oStream.close();     fc.close();     }    catch(Exception e){    Dialog.alert("EXC in saving image.  EXC = "+e);}
  

  The solution to the half of my problem was this:

  First, I created a directory with a separate connector.  Then I closed this connector and set up a second for the image.

  Then I saved my image in the new directory.

  The call of "connector.open" () looks like this for the two respective calls:

  // to create a directoryConnector.open("file:///SDCard/BlackBerry/pictures/myDirectory/",Connector.READ_WRITE);
  
  // to save myFile in the directoryConnector.open("file:///SDCard/BlackBerry/pictures/myDirectory/myFile.png", Connector.READ_WRITE);
  

  I will mark this as comprehensive and open a new thread to store petrol issues I've had.  That way I hope that someone will learn something.

  If anyone has questions, feel free to post it here or private message me and I hopefully will be able to explain what I did better.