PIX V6.2 of lists of access and authentication

Similar Questions

• Orchestrator device access and authentication of the rights on the workflow

  Hey all,.

  I had a strange problem with the last device Orchestrator:

  Sign-ON the value in the device, I can see the vCO server in the web client, can start the flow of work, all good. But when I try to change a worklof access rights in the vCO client, I open the switch, push enter the filter field or a substring to find a group, but the selector only say loading and is never showing all groups.

  So, I tried to set the AD authentication. Now, I can see my ad groups in the selector window. But I can no longer see the vCO server in the web client and see not all workflows.

  I checked the site configuration vCO, my user is part of the group admin vCO. I also checked the registration of the Oct on the vCenter server. I can see the extension of vCO beeing is properly registered in the CROWD.

  Also workflows are running and are able to run on the vCenter server. I just do not see and cannot run from the vSphere client.

  If anyone has any idea why

  (a) I see no groups in the access rights selector add when SSO authentication? It worked only once in the past

  or

  (b) why I can't see the vCO server and workflow in the web client even if my user is part of the group admin vco?

  Thank you!

  Tim

  Which SSO/vCO/Web Client versions/versions do you use?

  I remember there were bugs related to the AD Setup mode of windows authentication integrated (supposed to be fixed at some point). You can try to add your ad as a type of Server LDAP identity source just to check if the groups will appear in the user interface?

• Excel, Access and Word can't be my program list in the start menu

  Excel, Access and Word do not appear in the list of programs on the start menu or anywhere else. The only way I can use them is by opening a file that uses. It's on a pc bought last summer, using the latest version of Windows, installed programs Microsoft etc. How can I make it appear?

  Matt C

  Hello

  Follow the steps below. It can help to solve the problem
  1. open the Start Menu.
  2. in the area of the white line (search), type regedit and press ENTER.
  3. click on continue in the UAC prompt.
  4. in regedit, go to

  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advance

  5. in the right pane, right-click on StartMenuInit and click on modify.

  NOTE: If you do not StartMenuInit, then click on New, and DWORD (32-bit) value. Type StartMenuInit and press ENTER.
  6 type 3, and then click OK.
  7. close regedit.

  8 disconnect and logon or restart the computer to apply the changes

  EDITING REGISTRY WARNING:

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

• How can I get my list of sites and FTP access, password etc... (old win 7 on an external drive)

  Hello, this is not considered a regular registered sites export (I have many)... and it's a mistake.

  In short, after computer out, I got the hard drive I have USB (old win 7 pro on an external drive)

  How can I get my list of sites and FTP access, password etc...

  they are encrypted in the registry if I'm not mistaken?

  any idea?

  Thank you.

  (Google translation)

  proceedings found:

  Just do an export of the new common/site .reg file and the modifier with the values of the old and then importing, everything works

  Thank you

• Why Game Center on my device is unable to access the list of friends and the list of games

  Game Center do not work.

  The only thing that works is the home screen.

  

  I can't change my message of player.

  For a list of friends and the list of games, there is a message saying that there are problems with the network.

  

  

  What can I do?

  Try going into settings > game Center. Disable the options for the recommendation of a friend, and then go back to the options you want.

  TT2

• NAT 0-list of access

  NAT with NAT Timeout values 0

  A server outside the firewall starts a session on the server inside. The server stores the session via the IP address and the Source port inside this connection must remain open, but if there is no communication after the time specified in the timeout xl, it is demolished... then, outside server initiates a new session with a source port different... Once this happens several times, the service on the internal server dies.

  If I use:

  notimeout list allowed access host ip 10.10.10.4 255.255.255.255 any

  NAT (outside) 0-list of access notimeout

  As the pix don't build an xlate array, it will bypass the timeout for the xlate? Once 10.10.10.4 allows a connection to a host on the otherside of the pix, will he be able to be idle indefinitely?

  Thank you

  Of course, but you have some problems of syntax. Refer to the following:

  PIX #(config) access-list no.-Timeout allowed ip 10.10.10.1 host 172.16.1.1

  PIX #(config) nat (inside) - No.-Timeout 0 access list

  PIX #(config) conn timeout 0:0:0

  * No need for 255 mask all when you specify host. And you want to apply the NAT inside interface. Translations when using a nat ACL 0 device still can be built from the less secure interface. And your timeout on the conn will be global. I do not recommend the use of what it can cause side effects. Each conn that is left in an open incorrectly state never fade conn PIX table. This can cause memory exhaustion over time, so if you're going to do this, please check the "County conn hs' and"sh conn detail"often of output and make sure that you don't have many & open on the PIX. It may require manual intervention you clear the & or reload the PIX.

  If you are in a situation where the connection must remain open indefinetly between these machines, you may be better of the location of these two hosts on the same segment so as not to take these measures. Just a thought.

  Scott

• PIX: Allowing servers in the DMZ access inside Server

  Hello

  I'm building a PIX 520 from scratch using 6.2 (2) and PDM 2.1 (1). I have 3 interfaces:

  outdoors (sec0) - xx.xx.xx.xx

  inside (sec100) - 10.100.1.0/24

  DMZ (sec10) - 172.16.254.0/24

  All was well with the modules until I started the task to allow the dmz hosts access internal hosts. I'm having problems as soon as I create an access for example rule:

  access-list permits dmz_access_in tcp host 172.16.254.20 host 10.100.1.35 eq ldap

  Problem 1:

  PDM alerts must be a static translation for 10.100.1.35 between the inside network and the DMZ. I would like the 172.16.254.20 server to the access server to the 10.100.1.35 using his real address of 10.100.1.35. Can I just give these commands:

  static (inside, dmz) 10.100.1.0 10.100.1.0 netmask 255.255.255.0 0 0

  dmz_inbound_nat0_acl ip access list allow any 10.100.1.0 255.255.255.0

  NAT (dmz) 0-list of access dmz_inbound_nat0_acl outside

  and then:

  access-list permits dmz_access_in tcp host 172.16.254.20 host 10.100.1.35 eq ldap

  Access-group dmz_access_in in dmz interface

  .. .will this work without problems?

  Problem 2:

  The rule of implicit outbound traffic to DMZ is broken - why? I need servers DMZ in order to access the internet without any discomfort.

  When I try and insert another rule to this effect, the following is inserted in the PIX config:

  dmz_access_in ip 172.16.254.0 access list allow 255.255.255.0 any

  This command now allows any server DMZ access all devices on my internal network! How can I solve this?

  I hope someone can help... Thanks in advance,

  Tariq.

  A problem 1, you don't need the nat statement 0 and correospnding-access list. The static method is sufficient.

  Problem 2: as you apply an access list to the DMZ interface, you must expand to include Internet access as well. If this is what you need, I would try something like this:

  access-list permits dmz_access_in tcp host 172.16.254.20 host 10.100.1.35 eq ldap

  access-list permits dmz_access_in tcp host 172.16.254.30 host 10.100.1.35 eq ldap

  ...

  ...

  etc. to allow the required access to the Interior.

  deny the dmz_access_in of the ip access list any 10.0.0.0 255.0.0.0

  dmz_access_in ip access list allow a whole

  Of course, you want to settle this as requires it.

• Problems with the side of accessibility and shortcuts computer locking

  Sony laptop Vaio Model: VGN-N21E/W

  My Toddler has managed to activate the shortcuts as follows:

  When I press the button 'u' when entering my password at the start of the menu the menu of accessibility and the only way to go beyond, it is to select something from the menu and then choose No.  I know I could reset my password, but I would like to get the problem sorted.

  Once access to Windows Vista is done, whenever I press the key 'L', the computer locks and I have to enter my password again, and then displays the menu of accessibility.

  It would be an understatement to say that it makes me crazy.  I had to copy the l and paste whenever necessary!

  Any help would be much appreciated

  Thank you

  It seems that your a young hit just the right combination of keys to activate the access keys.

  Click on the Start button and type > 'turn on' > and select enable easy keys for quick access in the list.

  Uncheck all the options and select 'Apply', and then click OK.

  What do have?

  Please let us know

  Mark <> Microsoft Partner

• Uninstalled program is still listed under "programs and features".

  Original title: a program is listed in programs and features. It was uninstalled and deleted directories. Yet, it still shows in the list programs and features. How can I remove it?

  I had installed this program before. I thought I had uninstalled. I tried to re-install this program, but cannot. I checked the list of programs, and it is still in the list, after being uninstalled. How do I remove it from the list?

  Hi n4ctf,

  Take a look at this link http://support.microsoft.com/kb/314481

  Edit the registry to remove an entry. This link refers to Windows XP but I checked with Windows 7 and it works so it should work with Vista.

  Once you have access to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall you will see a list of numbers. You will need to go through each of these numbered editions to find the program you want to remove. Click on a number in the left column, for example {08D605B4-DCD1-451F-ABD7-52E6BB868E4E} and you will see then the details is in the right column of the registry editor. See the 'full name' so check to see what the numbers program refers to.

  Normally, I would recommend that you try to reinstall the application rather that tinkering with the registry, but as you have already tried unsuccessfully to re - install, change the registry could be the last option. By the way, before making any changes in the registry, make sure that you back up the registry first. This link of my website will show you how to back up the registry:http://vistasupport.mvps.org/backup_the_registry.htm

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: Web:http://www.winuser.co.uk;  Web: http://xphelpandsupport.mvps.org;  Web: http://vistasupport.mvps.org;  Web: http://www.silversurfer-guide.com

• Windows Media Player is missing in Set Program Access and Computer Defaults

  I recently discovered that when I wanted to install a default media player, Windows Media Player was absent from "Default programs". When I ran a search on this problem, I had the suggestion that I enable access to Windows Media Player with "Set Program Access and Computer Defaults." However, when I tried this, I found that Windows Media Player was also absent from "Set Program Access and Computer Defaults"! Now, what I want to know is, how to restore Windows Media Player in the list of Set Program Access and Computer Defaults?

  Here's a hint: I do not have full access to Windows Media Player via the start menu.

  Brandon Taylor

  Brandon Taylor

  Hello, Brandon Taylor,.

  We will try to reset the Windows Media Player by using the following steps:

  Uninstalling and reinstalling Windows Media Player:
  Step 1.
  Uninstalling Windows Media Player:
  1. go to start and in the search type "Turn Windows willing or not.
  2. click on "Turn Windows features on or off".
  3. search for multimedia and uncheck the brand in the face of Windows Media Player.
  4 restart the computer
   
  Step 2.
  Reinstall Windows Media Player:
  1. go to start and in the search type "Turn Windows willing or not.
  2. click on "Turn Windows features on or off".
  3. find the multimedia functions and place a check mark in front of the Windows Media Player.
  4 restart the computer.

  Now, go to default programs, Windows Media Player is displayed now?

  If please reply back and let us know if this can help, or if you still need help.

  Sincerely,.

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• RV180 need some advice/Suggestion regarding the rules of access and Services

  Hi, I expected to get some advice or suggestion with a RV180 question.  I have a cable modem connection that connects to my port WAN RV180 and we have a single static IP address on the WAN port and everything works great.  We have an internal Exchange Server, so we have a few inbound rules access allowing for ports 443 and 25.  It all works.

  This is the question that I encounter.  We have now another service internal now needs outside inside access on port 443 (https), but I already have this configuration on the router for Exchange and when I have both sense, of course, it won't work correctly because the router just takes the first rules of access and use the one that works very well for traffic Exchange , but not my other service.

  Is there another way to get this job where I can have two internal services on port 443 and the router can forward traffic appropriate to each of them since my first IP? (it doesn't really matter if I had two IP addresses because it always hits the same access list for internal services)

  All advice or suggestion would be great

  Hi, yours is a general networking, not specific to RV180 problem.

  As you have only one IP public (on the WAN port), you only have a single port 443, you can support two services outside-to-inside.

  The cheapest solution is one of the services to another port, if the service permits.

  The most expensive solution is to have public IP addresses.

• Range of ports to be specified in a long list of access

  Is there a way to specify a range of ports at the end of a long list of access on a router. I mean something like ' access-list 101 permit tcp 10.10.10.0 0.0.0.255 20.0.0.0 0.0.0.255 eq 6000-6016'.

  Thank you

  You can do something like...

  myACL extended IP access list

  permit tcp 10.10.10.0 0.0.0.255 20.0.0.0 0.0.0.255 gt 5999

  permit tcp 10.10.10.0 0.0.0.255 20.0.0.0 0.0.0.255 lt 6017

  deny tcp 10.10.10.0 0.0.0.255 20.0.0.0 0.0.0.255

  Come and play with the parameters 'lt' and 'gt '.

• Access and download FTP on VPN problem

  Ok

  Here's my situation, we connect to Cisco ASA 5505 on IPSEC VPN cisco forwards the request to our router Juniper.  What we do on the VPN works exept FTP #1

  Here I am the Cisco config (with personal information removed).

  problem in society is the IP addressing as been IMO butched

  We have 6 guests

  1.0

  2.0

  3.0

  4.0

  5.0

  6.0

  Since most routers use 0,0 1,0 or 2,0 most of our clients cannot connect to the VPN, then my boss set up our Juniper to translate the IP address

  So make us 202,0 access 2.0

  Example if to access a server in 192.168.2.220 in RDP that write us in windows RDP 192.168.202.220 and converts of Juniper data 2,220 and everything works fine

  EXCEPT FTP.

  The FTP server is 192.168.2.19

  So if I write in IE or Firefox (ps file zilla does not work)

  FTP://192.168.2.19  I get the list of files. but when I click on a folder or file, I get a time-out error.

  so that if I do ftp://192.168.202.19 I don't even no initial registration.

  If I look in the Juniper I can see data entry

  So the problem seems to be coming back from the Juniper or cisco.

  The FTP server is also part 3, so when I called the company to see if it is active or passive.  They said that it is both.

  I guess that the problem comes from the Juniper but still take a chance

  ASA Version 8.2 (1)
  !
  Terminal width 250
  router host name
  activate the encrypted password
  encrypted passwd
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.192.2 255.255.255.252
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP x.x.x.x 255.255.255.248
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  grp_outside_in tcp service object-group
  Description Ports require for internal transfer
  EQ smtp port object
  EQ port ssh object
  access list inside-out extended ip allowed any one
  access list inside-out extended permit icmp any one
  permit no_nat to access extended list ip 192.168.0.0 255.255.0.0 10.250.128.0 255.255.255.0
  list access tunnel extended split ip 192.168.0.0 255.255.0.0 allow 10.250.128.0 255.255.255.0
  access-list 101 extended allow ip 10.250.128.0 255.255.255.0 192.168.201.0 255.255.255.0
  access-list 101 extended allow ip 10.250.128.0 255.255.255.0 host 192.168.202.19
  access-list 102 extended allow ip 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0
  access-list 102 extended allow ip 10.250.128.0 255.255.255.0 192.168.2.0 255.255.255.0
  access-list 103 extended allow ip 10.250.128.0 255.255.255.0 host 192.168.202.19
  access-list 103 extended allow ip 10.250.128.0 255.255.255.0 192.168.203.0 255.255.255.0
  104 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.204.0 255.255.255.0
  104 extended access-list allow ip 10.250.128.0 255.255.255.0 host 192.168.202.19
  105 extended access-list allow ip 10.250.128.0 255.255.255.0 host 192.168.202.19
  105 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.205.0 255.255.255.0
  106 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.206.0 255.255.255.0
  106 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0
  114 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.214.0 255.255.255.0
  114 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.201.0 255.255.255.0
  114 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0
  114 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.203.0 255.255.255.0
  114 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.204.0 255.255.255.0
  114 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.205.0 255.255.255.0
  114 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.206.0 255.255.255.0
  access-list 200 scopes allow ip 10.250.128.0 255.255.255.0 192.168.203.0 255.255.255.0
  access-list 200 scopes allow ip 10.250.128.0 255.255.255.0 192.168.204.0 255.255.255.0
  access-list 200 scopes allow ip 10.250.128.0 255.255.255.0 192.168.205.0 255.255.255.0
  access-list 200 scope allow ip 10.250.128.0 255.255.255.0 host 192.168.202.19
  400 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.201.0 255.255.255.0
  400 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0
  400 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.203.0 255.255.255.0
  400 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.204.0 255.255.255.0
  400 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.205.0 255.255.255.0
  400 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.206.0 255.255.255.0
  400 extended access-list allow ip 10.250.128.0 255.255.255.0 192.168.214.0 255.255.255.0
  access-list 201 extended allow ip 10.250.128.0 255.255.255.0 192.168.201.0 255.255.255.0
  access-list 201 extended allow ip 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0
  access-list 201 extended allow ip 10.250.128.0 255.255.255.0 192.168.206.0 255.255.255.0
  extended access-list of 500 permit tcp 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0 eq ftp
  extended access-list of 500 permit tcp 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0 eq ftp - data
  extended access-list of 500 permit tcp 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0 gt 1024

  pager lines 34
  Enable logging
  timestamp of the record
  debug logging in buffered memory
  recording of debug trap
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool mobilepool 10.250.128.100 - 10.250.128.130 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 621.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access no_nat
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
  Route inside 192.168.2.0 255.255.255.0 192.168.192.1 1
  Route inside 192.168.201.0 255.255.255.0 192.168.192.1 1
  Route inside 192.168.202.0 255.255.255.0 192.168.192.1 1
  Route inside 192.168.203.0 255.255.255.0 192.168.192.1 1
  Route inside 192.168.204.0 255.255.255.0 192.168.192.1 1
  Route inside 192.168.205.0 255.255.255.0 192.168.192.1 1
  Route inside 192.168.206.0 255.255.255.0 192.168.192.1 1
  Route inside 192.168.214.0 255.255.255.0 192.168.192.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  Enable http server
  http 192.168.2.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac floating
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dyn1 1 set transform-set floating
  Crypto-map dynamic dyn1 1jeu reverse-road
  mobilemap 1 card crypto ipsec-isakmp dynamic dyn1
  mobilemap interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH 192.168.2.0 255.255.255.0 inside
  SSH 192.168.192.0 255.255.224.0 inside
  SSH 10.0.128.0 255.255.255.0 inside
  SSH timeout 5
  SSH version 2
  Console timeout 0
  dhcpd outside auto_config
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal mobilegroup group policy
  internal mobile_policy group policy
  attributes of the strategy of group mobile_policy
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel

  (User with the access restrictions section list)

  type tunnel-group mobilegroup remote access
  tunnel-group mobilegroup General-attributes
  address mobilepool pool
  Group Policy - by default-mobile_policy
  mobilegroup group of tunnel ipsec-attributes
  pre-shared key
  !
  Global class-card class
  match default-inspection-traffic
  inspection of the class-map
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:4d936450878b9803a1fdde1c7f0fd807
  : end

  I saw Application Layer Gateway (ALG of Juniper) give a problem with the FTP flow. Check to see if it is activated and flip on (or off) and try again your ftp.

  ScreenOS 6 + (Netscreen firewall), the command is 'get alg '. For ScreenOS 5.4 or lower is a hidden command ' get the registry nat vector | I FTP ".

  For the Juno (SRX Firewall) is to "see the alg decision."

• How to display the list of temporary and free sites that we use?

  Adobe Web Host - Free Sites.

  How to display the list of temporary and free sites that we use?

  When you're connected creative cloud, we used to be able to view the temporary and lots of 5 free sites that we use hoe.

  Could not find a list on my creative cloud account or when the link to 'Manage' in the Muse.

  No mention of the free sites in the FAQ. Is there a change in policy? Are always included in the subscription of the free sites?

  - Adobe Muse help | Adobe Muse / Common Questions .

  When I publish in Adobe Muse CC, must I pay for hosting with Adobe?

  Adobe Muse CC allows you to publish your Web site temporary on the platform Adobe of accommodation free of charge for a trial period of 30 days. This gives you the ability to send a direct URL to your client for review. All sites with Adobe trial mode will include the field "businesscatalyst.com" in it. If you decide to take the live site by paying for monthly hosting, you can transfer your domain name and delete the subdomain businesscatalyst.com. Or you can export the HTML and host the final site with a host of your choice.

  //

  Yes, don't know why they took out of the cloud interface.

  But if you go to http://www.businesscatalyst.com/partnerportal and you connect with your ID cloud you will have access to all your cloud sites and many other features.

• Why is my iPhone 5 number listed as 'unknown' and not listed in iMessage and FaceTime?

  I am a customer of StraightTalk. Originally, I had an iPhone CDMA 5 purchased directly from this company. After three years, the battery swelled and I came out of the Apple Store on Thursday with a replacement. After inserting a SIM to speak directly into the device and setting up, I can make calls, send text messages, use the cell data, etc.

  However, my phone number in the settings is listed as 'unknown', and it is not listed at the top of the contacts screen. I can't send messages in my phone number iMessage, because it is not even listed as an option. Ditto for FaceTime. After several hours on the phone with Straight Talk, they determined that my phone service is configured properly, and it is a phone number.

  Does anyone have a solution for this? It is incredibly frustrating that the iPhone 5 does every thing I need to do, and I prefer to keep my phone from replacement $ 75 for three years before moving on to an iPhone SE.

  Hello, smirza!

  Thank you for using communities of support from Apple!  What I understand in your post, you got a replacement iPhone 5 and have found that your phone number is not listed in settings > phone and iMessages/FaceTime.  Your number should certainly be in all those places, so I'm happy that you came here, then we can help you understand what is happening together.  Check with your mobile provider was a big first step.  I have other ideas for you as well:

  1. It seems that you already have the latest version of iOS (9.3.4), but we will also check your carrier settings are up to date: iOS: update your carrier settings
  2. If you haven't already done so, save your iPhone on iCloud or iTunes: How to backup your iPhone, iPad and iPod touch
  3. On your iPhone, go to settings > Contacts > My Info and make sure that your personal contact (with your iPhone phone number) card is selected.
  4. Go to settings > phone > my number and see if you are able to manually, enter your number and save it.
  5. If none of these steps work, try to restore your phone from the backup that you made: restore your iPhone, iPad or iPod touch from a backup
  6. If you still don't see your issue, try restoring your phone as a new and see if your number is: use iTunes on your Mac or PC to restore the iPhone, iPad or iPod to factory settings

  Have a fantastic week!