Port Ethernet on X61s

The ethernet on the X61s port does not moored in the ban but only when the ban.

Is this normal? If this is not the case, how do you get the port to work while in the ban?

bhohenstein, welcome to the forum,

It is normal that the ethernet port on the ban is a 'place', as the VGA port and modem port. The system can only support an ethernet port. When you fasten the ethernet on the ban become active port and internal ethernet port becomes disabled. Attach your cable ethernet to the ban and everything should work fine.

Hope this helps

Tags: ThinkPad Notebooks

Similar Questions

  • HP ENVY TS m6 Sleekbook: port Ethernet HP ENVY broken

    Clip of port Ethernet of my computer broke, not the hinge plastic broke.  This is the part that leans down to cut the Ethernet cable to the computer.  If I hold the cable into the Ethernet port on my computer still receives data through it.  Let me know if you are in need of any more details that I have not thought.

    The part broke in the Middle East and must be replaced.

    Here is the Service Manual:

    Link to the manual

    See page 40. The cover is held to the frame with 2 screws inside. It is a replaceable part and is included in the kit of plastic.

    Module RJ45 cover (plastic kit) 727464-001

    HP wants to $55 for her:

    PartSurfer link to coverage of the order

    $ 5 shipped on eBay:

    http://www.eBay.com/ITM/HP-envy-TouchSmart-M6-K000-Ethernet-LAN-RJ45-cover-door-latch-727464-001-/281322149224?PT=LH_DefaultDomain_0&hash=item41801b5568

    If you have a manual with instructions for replacing it and a link to order for $5. If there is nothing else, after return and we can try to help.

    If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  • ENVY Phoenix Desktop - 850-065: Add the port ethernet on the desktop

    I want to add a second ethernet port on the desktop... any recommendations, the Gathas, the various factors to consider... I seem to have three ports of extension on the PCI bus... one of them would be the target (or what)... any recommendations on ethernet brand and model to consider...

    Any wisdom on the subject will be sincerely appreciated...

    Hello

    There are many models/products of ENVY Phoenix Desktop - 850-065 series. In any case, according to your description you can use a normal PCIe 1Gig card. There are a lot of cards around, 1 port, 2 ports or more. Please make sure that there are drivers CD or at least it shows you where to find driver (from the site of the manufacturer).

    Kind regards.

  • Connection cRio 9074 second port ethernet to another device via VISA

    I'm trying to connect a DAQ Yokogawa system to a cRio 9074 via the second ethernet port. I activated the second ethernet port of the cRio with a static IP address on the same subnet as the data acquisition system. I installed the driver NI-VISA and NOR-SERIAL on the cRio. I can compile the code on the cRio and I'm sure that the code works when I connect to the acquisition of data to a PC. I get an error on the open VISA VI.

    Am I missing something or is it not possible to connect the second ethernet port on the cRio in this way?

    Thank you

    Thank you for your response. I found the same information that you provide, but decided to give it a try.

    A few minutes ago, I was able to perform communication between the cRio 2nd access Ethernet DAQ Yokogawa. I managed to do it using the VISA controls. To communicate with the host PC, I get the information of the DAQ with the cRIO as described above and then use shared variables to publish data on the network connected through the first ethernet port.

    If anyone wants to reproduce it just to make sure that the two ethernet ports are configured with IP addresses on different subnets that are configured for TCP communication. If more details are to be simply send me a message.

    Kind regards!

  • M93p - removal of connection network because of the loose port Ethernet - MT M10AA S18G00

    Hello

    A few months ago, we bought 149 new M93p devices for a hardware upgrade. In the new image, we began having a large number of errors and failures. We discovered that the network connection were down when the ethernet cable is touched or moved slightly. Initially, it was suspected that our cables were at the origin of the problem. It was quickly determined that all connection cables, with the exception of a set of very old Cat 5 cables, had the same problem. From what I can tell, it seems that the tolerances to the ethernet jack are loose or the pins are set too low.

    Everyone knows this problem or has had random loss of network connectivity? I was told that this particular model of M93p was a new race. Thanks in advance for any help!

    I had this same problem. After a month or more to work with the resolution of complaints from client Lennovo, turns out be a technical problem with the RJ45 port. The solution? -Lenovo has sent several enlarged RJ45 connector dongles. Problem solved.

  • How can I configure a port Ethernet NI9792 gateway to communicate with a cRIO CAP?

    Salvation OR engineers,

    I intend to use my gateway NI9792 in the following way:

    1. a single Ethernet port for network connection. That's how I'm developing, download the software and monitor my request through my PC in my office.

    2. the other port to communicate with a cRIO device? If so, how can I do it?

    It seems to be a stupid question, but I really couldn't work this!

    Thanks in advance,

    Luiz

    Good afternoon, Luiz

    Follow the first link to guide the module which can be used and other links to the best part of bore configuration CRIO. For any question, please contact us.

    How to set my time on the NI WSN-9791 or NI 9792 gateway server?

    http://digital.NI.com/public.nsf/allkb/44FA322FAFF8D58D862575BD00591A54?OpenDocument

    Configuration and NI WSN product guide
    http://zone.NI.com/DevZone/CDA/tut/p/ID/8710

    Configure the Ports of double Ethernet on real-time controllers

    http://digital.NI.com/public.nsf/allkb/67F94BB93BCE32CF86257367006B3659?OpenDocument

    video installation and installation CRIO

    http://www.NI.com/SWF/demos/us/cRIO/outofbox/

    Automatic configuration of network for the cRIO-9073 and cRIO-9074 CompactRIO controllers

    http://digital.NI.com/public.nsf/allkb/37C790309A210A748625757000570938?OpenDocument

    Sincerely,

    Mauro Vera.

  • is my function of co-dependency on my removed switched phone modem.no lights on the port, ethernet port net connect.

    Thank you ~ RELLIK ~ for your help check modem switched on the lights. DSL, sr100g.problem now extends to my ethernet port lights not on.some time ago I removed my mod.which of internal phone has been used for DIALUP.it prevented my lap.from start after dell logo splash screen.so I used an external modem QUESTION.IS MY PORT AND LIGHTS CO-DEPENDENCY ON MY OFF DIAL UP TV TELEPHONE MODEM ETHERNET?

    You should stick to a thread, or at least to copy texts from that earlier instead of making people to drive to the top of your thread earlier.

    It would also help greatly if you have formatted your messages using sentences and paragraphs.  It is very difficult to read this single run-on sentence:

    Thank you ~ rellik ~ I got the my dsl phone co.check, sr100g, and on.problem lights came now extends to my lap.port lights don't turn only not on.so here we go again! I will try to clean the pins, eight of them and see, then if it doesn't maybe goinside to check connections. HOWEVER! I ' M A LITTLE MISTIFIED ON ANOTHER TOPIC! I had a phone internal modem.actiontec.mp100mdf2.this to that I used. DIALUP INTERNET.discouvered the modem stopped lapt.from turning on.after dell logo splash screen.desided to disassemble and clean took out and decided, out of curiosity, to turn on the system and it came, I reversed and reconnect, modem usb external bad.bought, worked, BUT very good! COULD YOU ME TELL IF MY ETHERNET CONNECTION IS CODEPENDENT ON MY PHONE DELETED. MODEM? kentempo.

    or, in this case, this one:

    Thank you ~ RELLIK ~ for your help check modem switched on the lights. DSL, sr100g.problem now extends to my ethernet port lights not on.some time ago I removed my mod.which of internal phone has been used for DIALUP.it prevented my lap.from start after dell logo splash screen.so I used an external modem QUESTION.IS MY PORT AND LIGHTS CO-DEPENDENCY ON MY OFF DIAL UP TV TELEPHONE MODEM ETHERNET?

    To answer your question of capital letters: no, the behavior of your Ethernet card, including its lights, has nothing to do with your telephone modems, current or previous.

    • Open the Device Manager (start > run > devmgmt.msc > OK)
    • Click on the + to the left of network adapters to expand the category.
    • What devices are displayed?
    • Y at - it a warning next to your network adapter icon?  If so, double-click on and to report to what appears under the "device status".
    • Close the Device Manager and open the network connections (start > run > ncpa.cpl > OK)
    • You have an icon for "Local Area Connection"?
    • What is written on the line under the title "Local Area Connection"?
    • Right-click on the icon and select Properties
    • In the 'Général' tab there is a window titled "this connection uses the following items" - report anything that is listed in this window.
  • lights of port Ethernet turn only not on dsl port will not turn on.

    just got dsl modem, smart rg model SR100G, after plugging the ethernet cable, of lily for dell inspiron 8100 laptop, no port lights and no computer laptop port lights.when I tried to conect to the notice of the net web incapable of connect.connection tested cable good.presently using the dial upward. CHECKED in the properties of INTERNET PROTOCOL [TCP/IP] and confirmed that the ip address, subnet mask default gateway fields are empty.

    Seems that the problem is with the modem. Contact the manufacturer of the modem or your ISP.

  • Problems with ports ethernet E4200

    I have problems with my ethernet ports on my router E4200 V1.  I do not get on flow rate of 12 Mbps on a single connected wired computer.  If I replace it with a simple switch 5 port I get 60 Mbit/s using the same cables.  I looked through the creation and cannot come up with any solution.

    Any help would be greatly appreciated.

    Thank you

    Mike

    OK I tore across the network.  Started from scratch and found the problem.  It is quite strange, but everything works fine!

    I discovered through the process of elimination that the cisco router did not like my Panamax Lan UTP.  Cisco is apparently more strict with the signal than the simple switch or refurbished netgear router.  I had the protection on the power strip 6 Max near the iMac.  The totally weird part is that slowed down the entire network.  Streaming is now pending on 60Mbps at each connection to the local network.

    Thank you all for your time I walked through this weird problem.

    Mike

  • Adding additional Ports Ethernet to the router EA6300

    Friends,

    I have a setup of typical network with a cable modem in progress of execution to an EA6300 wireless router. The EA6300 also has a cable ports but I have 4 of those filled and I would like to extend it. I have an older Linksys ethernet hub, but it does seem like one of the entries EA6300 to plug in the supply plate works. Is there a way that it works, or do I need another piece of equipment?

    Greg

    But of course the without wire in this particular book didn't work for a long time, so I had to revisit this issue and found out that the ethernet hub works very well except for port 1. I am logged in ports 4 & 5 and all is well. This solution should work perfectly for the foreseeable future and thank you for all the support and assistance with this!

  • Ports Ethernet in router wireless set up as access point

    If I set up a wireless router as a wireless access point, can I still connect to the Ethernet ports on the router?

    Yes.

  • Ports ethernet on my new Linksys E1500

    I bet dumb question, but I was not able to find an answer elsewhere, so I thought I would ask here.

    If I connect to a computer for my new E1500 via its ethernet ports will get the same speed as if I was directly connected via an ethernet cable from my modem? In short, these ports work around the appearance of the router wireless and connect directly to the modem? Ideally from a computer is located next to the router I this and only use wireless for the other computers in the House.

    Everywhere I read, I read that wireless is going to give me a slower connection that I have with my computer connected directly to the modem.

    Thank you.

    John

    Did you mean Mbps Mbps not? If Yes, then you should be good .

  • WAP610N Port Ethernet speed

    What is the speed of the Ethernet port that connects the WAP610N to the local network. Why is it not mentioned on the box or the manuals? I guess it would be 1 GB because what is the meaning of facilitate a 802.11n wireless network when the speed of the connection to the cable network is anything but 1 Gb, I am mistaken?

    The speed of the Ethernet port is 10 / 100 Mbps.

    http://Linksys.custhelp.com/cgi-bin/Linksys.cfg/php/enduser/std_adp.php?p_faqid=19927

  • Laptop HP Pavilion 15-n004tx: damaged Port Ethernet

    One of the pins in the Ethernet port on my laptop has been damaged, and since then I can not connect to any LAN network. The port is replaceable? If Yes, what is replacement cost? My laptop warranty has expired.

    thnx

  • Ports Ethernet on PIX-4FE-66

    Hello

    I just inserted a PIX-4FE-66 ethernet card in my pix 515 firewall. In addition to eth0 eth1 en, I now see another inf2 interface. Wasn't supposed to see 4 additional ethernet ports? Ho I candy card. also I do not know which port is

    or E2, E3 etc can someone enlighten us in this for me please.

    Thank you.

    Greg, you need allow PIX-515-SW-R-UR = manufacturer, to convert the restricted (R) to HEART.

    Please evaluate the useful messages

    Rgds

    Jorge

Maybe you are looking for