Port Forwarding issue with HP Photosmart C7250 / Windows 7 / Linksys router

Similar Questions

• port forwarding issues

  I played with port forwarding with my two cams of linksys and other 3 g wireless network web pages on my local network I want to access from the outside world.  I have one to configure them to use other port 8081, but after a few experiments see it as useless.

  I have a router linksys WRT54GL running dd - wrt V23 SP2 firmware and ports 80,81 and 443 (all in the field "port of") transmitted to cam1, cam2 and Western Digital NAS drive respectively. I found that because I'm port forwarding in any case, the two cams can continue to use port 80 and I 80 and 81 in the ' port of "or side defined WAN port 8080 bothers me to my router gui.

  There's the rub for me, it is, I cannot use 80,81 and 443 of the side ports WAN routers forward my port, if I use a different port, I can't access anything whatsoever that is served as a web page. I discovered this when I installed the Transmission torrent client on my NAS drive, it has a web interface as well and uses the port 9091, however when I port transfer it via my router I can't web interface from outside my local network. If I change the WAN or 'port' 80 or 81 and let the 'port' to 9091 I get fine, but I need to disable the port front of webcam that uses this port.

  I was going to get a 3rd and 4th IP Cam but will have the same problem, because it seems that only I can use ports 80, 81 and 443, and they are already exhausted. (I use 443 for secure access to my NAS drive) Change the port number in settings/options to 1024 or anything else works that if I leave it on the side of port forwarding LAN, WAN-side must always be 80 or 81.

  The only way I can see around this is to create a page that will reside on my router or my drive NAS I can show more out of a camera on it - something, I want to do in any case.

  PS. I do not use TZO, but I use dyndns so my dns is myname.dyndns.org.

  Finally understood that there is a problem with blocked ports from my place of work, which is where I tried to connect from. When I connected to the internet with my laptop computer and aircard, I was able to get to ok. My solution when I want to check on the torrents of the work is to connect to my router GUI work, changing the port 80 or 81 and disable the webcam on this address.

• compatibility issue with the software for Windows XP

  When I try to install a program, it says that I need to be runniing in windows XP. I try to install the program in compatibility mode and get the same message, and the program does not load. When I called the technical support for the program they tell me I need to download a donwload of compatibility for microsoft. I find no download for this issue. Thank you for your help.

  You could ask Zoll Medical to be more specific about any download (get a link) that they could help you.

  You are in contact with other users of this equipment you can ask them if they have similar problems and have any alliterative solution.

  Have you tried right clicking on the shortcut to the Setup.exe and choose the option "Run As Administrator"?

• RV110W port forwarding issue and firmware 1.1.0.9

  I saw a reference to the date of issue for firmware 1.1.0.9 (I think it was the number) for the RV110W but if I navigate on the firmware download page I only see 1.0.1.6 available for download.  Is it available somewhere or I I confused and saw a reference to something else?

  I have a RV110W installed on a customer site that must be restarted about once a week because it stops, allowing incoming access to mapped ports.  For example, it stops transfer of connections on Port 25 for the e-mail server of the customer.  I thought for a while there was a problem with the mail server software, but after the elimination of other issues likely days, I rebooted the router and everything was fine.  Now the problem recurrs about once a week and reboot the router always fixed (it's week 3).  Shipping to ports 80, 443 and several others also stop working.

  I was hoping that this has been fixed in a firmware fix, but maybe someone has seen this problem?

  Thank you.

  The 1.1.0.9 firmware image is now available for download here:

  http://www.Cisco.com/Cisco/software/release.html?mdfid=283879340&CATID=268437899&softwareid=282487380&release=1.1.0.9&relind=available&rellifecycle=&RelType=latest

  This version of the firmware will not work with earlier versions of the language pack.  When you upgrade to the 1.1.0.9 firmware version, it is recommended that you check the option "Reset to factory default.

• Compadability issues with fallout 3 and windows 7

  I already tried to go under XP, XP SP2 & 3, Vista, Vista SP1 & 2

  I run it on a laptop with intel core i5 4 x 3GB of ram and geforce gt 520 m, 330 m 1 GB vram
  It worked fine on my old computer laptop amd turion 2 x 4 GB ram ati 3200 m 256 MB vram
  It will work fine on full setting up until I get to where I select my _ while it freezes
  I also tried on minimum settings (set to low temperature preferably windowed 800 x 450) and it always fails at the same place
  My drivers are as up-to-date as possible (nvidia didn't even pilots from the 300 series to the top yet) and I had the cpu running task manager was used only 23% and total of 1.4 GB of ram and video card gets warm barely im wondering if it could be a problem of compadability with the new 300 series?

  I solved the problem I am running a core i5 520 m and geforce gt 330 m on a toshiba satellite p500-st6844 and it came out of the box with hyper threading enabled (the problem) fallout 3 would not run after a lapse of time or a change of scene sertai, I checked the permissions I even ran it under admin account I've updated to the latest version with a supposed windows 7 total compadability fix made sure I had the last ditectx taken care of by my gfx card, I also made, I got the latest nvidia drivers (nvidia still has not all drivers update for the Witch of the 300 series only makes no sense, because they have the same hardware/software as the 200 series) I finally decided to turn off hyperthreading to see if that had nothing to do with it and I seriously doubt that but to my surprise she has a great even better than my office upstairs with a 8800 gtx, so if you have a gambling problem where the game starts well but crashes after a short period of time or during a change of scene and you have active hyperthreading, that might be your problem

• Compatibility issue with DVD Maker and Windows Media Player

  I was helping a friend with his DVD Maker and after successfully completing a DVD (music and images) using Windows Media Player music on our second attempt, he indicated that there was a compatibility problem with the music that he snatched from Media Player. He said that it would not accept the ".wma" format.  How do fix us the problem?

  I was helping a friend with his DVD Maker and after successfully completing a DVD (music and images) using Windows Media Player music on our second attempt, he indicated that there was a compatibility problem with the music that he snatched from Media Player. He said that it would not accept the ".wma" format.  How do fix us the problem?

  I'm no expert in this area, but I think that you used the wrong application, namely Windows Media Player.
  A month ago, I did 2 DVD with images and music. Here's what I did...
  Open Windows Movie Maker...
  1. I imported images in the timeline.
  2. I imported the music (wma in your case) file to Audio column / music.
  3. I have synced it so that the images and the music would start and end at the same time.
  Note : If you already have the video file with import loan, then simple music video to the timeline and go to step #4.
  4. I clicked on publish on DVD.
  Windows DVD Maker wil pop up. You know the rest of the steps.

  t-4-2

• Having a few issues with the functionality of Windows, need help.

  The question I want to have all started with Windows media player, it kept giving me an error whenever I tried to say something about some dll and she had to be reinstalled so I went in the programs and features Panel and took office and uncontrolled Windows media player in the media tab. I restarted my pc and when I am returned to features to reinstall media player it gave me an error message indicating an error has occurred. Not all features have been changed. Well, I restarted my pc again and it says failure configuration windows updates, returning to the changes before the logon screen appears.

  He did exactly the same thing every time I try to get media player back, gives me this error and is unable to set it up. Need help please, I'm frustrated and don't know what to do as I use media player as my default player. I'm running Windows 7 Ultimate x 64-bit with service pack 1 installed.

  (Moved to programs)

  Personally, if Id had malware on my pc, after a clean analysis Id make sure pictures of data, documents, etc. are saved.

  After that, you can try creating a new account admin test, and if it leaves you then try to install WMP for this account.

  With some malware is hard to know what that its alteration, but it sounds like it may have fiddled with your security access settings.

• m11x r2 issues with car wireless in windows 8

  I upgraded my laptop Windows 8, but I'm having some problems with the wireless card. After a few minutes of use, it will randomly fall the network connection. I have to disable and re-enable the network card to get connected again. Is there an updated driver for the wireless card? I think it's an Intel card, but maybe it's the Dell Wireless card.

  Hi, that give a try.

  Make a left click in the lower right corner and open Device Manager.

  Click network adapters and find your wireless card.

  Right-click on it and open properties.

  Click power management and uncheck the BOX "allow the computer to turn off this device to save power".

  Click OK, and then close all windows.

  You use the native drivers of windows 8 to run your wifi? If so and the solution above doesn't work try to download the correct drivers from the Microsoft or website killer, according to what brand wifi card you have.

• Problems with HP Photosmart C4380 wireless via a router from Cisco RV120W

  We recently purchased a Cisco RV120W wireless router and now we can´t connect our wireless Photosmart C4380 printer.

  During the installation process, we get the message: "the can´t computer communicate with the printer on 192.168.0.216. It can be caused by firewallproblems. Check that the 427 UDP port are not blocked in and out of traffic"(translated from Danish).

  If I remove the USB cable and try again, the installation continues and Announces: 'printer found – connected to the LAN' - but in the end: "Printer installation is not complete" - aurgh!

  The report-network printer looks OK all the way.

  Can someone help us we are frustrated.

  Greetings Jens Ove and Helge

  Sorry, but I'm not familiar with this device.  However, I would search in the areas of networks, VPN and security.

  You want to be sure of not having active VPN and also look for implementing isolation.

  This manual can help: http://www.cisco.com/en/US/docs/routers/csbr/rv120w/administration/guide/rv120w_admin.pdf

• HP photosmart C7250

  When I scan a document with my photosmart C7250 it comes out as a photo and I would like to convert a PDF document, but I can't. What can I try?

  Hello Cal14, welcome to the forums

  I saw your post not being able to scan in PDF format. I took a screenshot to give you an example of what you should see, or similar when you scan with the print screen software. Please send me a screen shot the back of what you see and also let me know which operating system you are running.

  

  Happy Monday!

• LRT224 - Dual WAN port forwarding

  Can you move forward say port 80 1 Wan IP and port 80 from WAN 2 to a different IP address. ?

  Also can you somehow choose TCP & UDP rather large only one or the other?

  I just replaced 2 routers with LRT 214 and LRT 224 TPLink its all works well. Except port forwarding

  With LRT224, a port forwarding rule is applied to the two WAN ports and two rules are necessary if you want to ship to TCP and UDP to the same internal IP address.

• Implementation of IPSec Port Forwarding on a Windows 2012 with a LRT224 Server

  Hi all I hope someone can help me validate my troubleshooting. I'm deploying a Server Windows 2012 that will server as a server vpn for customers. In place is a LRT224 with 4 VLANS set up. I have enabled port forwarding for IPSec (UDP/500), L2TP (UDP/1701) and L2TP (UDP/4500) to go on the server.

  In my Initial test, I put the LRT224 on the same network as the client of my test and realized the Test Client (10 Windows) to try to connect to the WAN of the LRT224 interface. I get this message:

  

  Thinking it could be the configuration of the server, I then put the client system on the same vlan on the LRT224 server. When I tried to connect to it directly by using the IP address of the server as a destination, he succeeded.  It is leading me to believe that it is the LRT224.

  I confirmed that VPN passthrough is enabled.

  The firmware version is by: v1.0.5.03 (February 22, 2016 10:12:17)

  Currently, the firewall is disabled (I would activate once I'm working)

  If anyone has ideas or notice a fault in my tests, I would really appreciate the feedback.

  If additional information would be useful, please let me know what you want and I can work for it.

  Thanks to all in advance.

  FreeFallFour wrote:

  I then put the client system on the same vlan on the LRT224 server. When I tried to connect to it directly by using the IP address of the server as a destination, he succeeded.  It is leading me to believe that it is the LRT224.

  It does normally not as I KNOW because the VPN in an outside in the process. You should test the VPN connection outside the server's IP subnet.

  You have the server configuration that the DNS server in the router to DHCP with DNS Proxy is disabled?

  Are you doing load balancing Internet connection?

• Photosmart C7250 is incompatibility with windows 8.1 Overview operating system.

  I installed windows 8 pro from form to preview pro 8.1 windows operating system and now the Photosmart C7250 printer I've stopped working.  It seems to need revised drivers.  In addition, the HP Solution Center has stopped loading.  Any ideas when new drivers will be sent?

  Keep watching the web page for new drivers.

• Anyone know of any compatibility issues with Windows 8 and RV series routers?

  I have a small network with a laptop computer, Windows 8, Windows XP desktop computer and a network MyBookLiveDuo storage device. I have sharing enabled between these devices. Everything worked well on a network switch. I replaced the switch with the RV110W VPN Firewall Router to add better security to my network before I have expand it. Since then, I have a laptop Windows 8 intermittent connectivity while the connectivity of the XP desktop computer shows no problem.

  On the laptop Windows 8 I ran network troubleshooting, and he complained that two devices on the network are (NAT) network address translation and the symptoms he describes is what I see. Problem is that I don't have a network Analyzer to look at the network in more depth. I looked online for the RV110W documentation and if NAT is listed as one of the characteristics, there is no discussion in the documentation on how to manage this feature in the router.

  I can connect to the Windows 8 laptop from Office XP and access shared content. I can connect to the Duo since Office XP without difficulty. However, except when they reappear periodically under the heading of my network in Explorer on the laptop Windows 8, I can't access the Office XP or the Duo of the laptop Windows 8. Curiously, however, I have a part of the Duo mapped as a network drive on the laptop Windows 8 and I can access it even when everything else has gone. Also, the interface of management for the Duo appears on the laptop Windows 8 and I can access the Duo to manage. Only, I can't access the shares on the Duo. Then all of a sudden they reappear under network in the file Explorer and I can then access. I think it must have to do with NAT, but I can't find anything out about it.

  If it's something I can turn on the router long enough to see if the problem goes away I would like to try, but I can't find it in the documentation, and I can't find it when I look aroiund in the management interface.

  The fact that I am not having the form of the XP desktop computer problem makes me think that a compatibility issue with Windows 8. Does anyone know if Windows 8 did anything with NAT? I try to get help from Microsoft Technical Support, but their level 1 tech told me to call Tech Support Pro when they open later this morning. Support cat Cisco won't open until Monday at 09:00.

  Also, throughout this connection problem Internet from the laptop through the router is never interrupted. It's strictly connectivity with other devices on the internal network that comes and goes.

  Hi Gregg,

  NAT must not play unless your applications on the internet. The "port Internet" or "WAN port" is a NAT port that converts your public IP address from ISP to your LAN subnet addresses. NAT allows multiple computers on a network to use 1 public IP address.

  If your devices are connected to the Ether "LAN ports" they are not affected by NAT unless they are Web applications. 4 'LAN ports"are 2 layer switch ports. This means that all local requests are forwarded by the switch ports.

  This device did replace exactly? The XP computers, DUET and window 8, make these products using the static IP address or you allow the RV110 to assign an IP address automatically? What IP address you are using on the LAN of the RV110?

  -Tom
  Please mark replied messages useful

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team