port high pass / low... connected on new access point...

Similar Questions

• Could you let me know on 3850 catalyst to connect to the access point status?

  Dear experts,

  The 3850 catalyst to connect the Access Point.
  I checked the OCC, but I don't know to connect the access point directly or indirectly...
  Is that it must connect the Access Point to the 3850 catalyst directly?

  Could you let me know on 3850 catalyst to connect to the access point status?
  I want to know the ORC page on this subject.
   
  Best regards
  Takuro

  Hello

  See below

  http://www.Cisco.com/c/en/us/products/collateral/switches/catalyst-3850-series-switches/qa_c67-722110.html

  Q. does the Cisco Catalyst 3850 in charge of indirectly connected access points?
  A. No. switch Cisco Catalyst 3850 will always take the CAPWAP tunnel locally. Pass-through or indirectly connected access point mode is not supported at this time. Note that a model SFP Cisco Catalyst 3850-12 or 24 channels can be a good choice to act as controller of mobility for a stack of switches Cisco Catalyst 3850 ending CAPWAP tunnels locally.
  HTH
  Rasika
  Pls note all useful responses *.

• With the help of new access points with old WLC 4100; LWAPP layer 2 switching 3-tier

  Hi all

  We currently use two solutions Wiresless LAN - a 10 AP1230 access points-based autonomous (5 years) and a solution based on a Cisco WLC 4100 (4112, running 3.2) with 12 AP1010 LWAPP access points.

  First thing, we are considering to replace the stand-alone solution with the WLC one. However, I'm not sure if we can use the new access points such as the LAP1041N or the LAP1252G with our current 4100 WLC. Access reported data sheets 'Cisco Unified Wireless Network Software Release 7.0 or later version' 'software '. Does this mean that these access points can only be used with controllers running 7.0 or later?

  If we are unable to use the new access points with our current WLC and need to buy a new controller: can we use access points AP1010 current with a new WLC as the Cisco 4402?

  Second thing, it is that we want to expand the networks configured on the WLC 4100 to another site that is connected via VPN wireless. Wireless Setup guide indicates that the LWAPP mode can be changed from Layer 2 to 3 layers so that the access points can be configured with an IP address, which allows you to place access points basically anywhere as long as IP connectivity exists between the AP and the WLC.

  Y does it as described in a document with the change of mode LWAPP layer 2 to 3 layers? Or ist just the following steps (if I understand correctly):

  -Change the Mode of Transport LWAPP on the controller of layer 2 to 3 layers

  -Creation of a PA-manager interface with an IP address in the same subnet as the management interface (tried that, without changing LWAPP mode transport first and not was not possible - error)

  With regard to different sites:

  -Configure option DHCP 43 with the IP address of the WLC or DNS with CISCO-LWAPP - CONTROLLER.localdomain

  -Make sure that the interface ap - manager can reach points on the different site

  Is it really just as simple as that? All information about it is very appreciated!

  / edit: I would also like to know if the 1260 series access point are backward compatible with 802. 11B. Whereas it is stated in 1040 and 1250 for example series data sheets, it is not particularly mentioned in 1260 data sheet.

  Thank you

  Michael

  Well, let's start with the simple question/answer

  With regard to different sites:

  -Configure option DHCP 43 with the IP address of the WLC or DNS with CISCO-LWAPP - CONTROLLER.localdomain

  -Make sure that the interface ap - manager can reach points on the different site

  Yes, it's as simple as that.

  As for other issues, looks like you would be better served with a forklift upgrade.  New controllers and new AP.

  Now, the AP 1230/1240/1250. all work on the 4.2, 1140 code starts with 5.2 and 1040/3500/1260 are 7.0

  The AP 1000 series is not supported after 4.2 code.

  Refer to here for the complete list of the AP and taken codes supported:

  http://www.Cisco.com/en/us/docs/wireless/controller/release/notes/crn7.0.html#wp610751

  From what I see, the 4100 is not supported after the train of 3.2.

  So, it really depends on what you are trying to accomplish with the upgrade.  If you are looking for a 80.211n support, you really want to be 5.2 or better, we had some problems with MRR + 40 Mhz channels, 4.2, 5 GHz band only.

• Cannot connect to Internet access point except on a Jetpack from Verizon.

  I am running Window 7 Home Premium. I can connect to the Internet using my Verizon Jetpack and nothing else. I tried to use my Verizon phone as a hotspot, I have a router Belkon 4. 1A and we tried through other points of access. It connects to the access point according to the plan, but it is XE offline to the Internet. I tried to update my drivers for wireless devices, and it is said that they are already updated.  I can connect when I'm wired. When I check properties properties IPv4 and IPv6 are shoddy outside. Install is the only thing not frayed on. When click on install, I get an error: cannot add the requested feature. the error is: these data are incorrect.  My wireless adapter is Realtek RTL8187SE Wireless LAN PCIE network adapter. Please help me I am so frustrated.

  Hi Sylvia,.

  I imagine the inconvenience that you are experiencing.

  Here are some ways you can follow to resolve the problem:

  Method 1:

  Check out the link and follow the steps in the article:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 2:

  Flush the DNS and request a new IP address of your ISP server by following these steps.
  a. click on start
  b. click on run
  (c) in the Run dialog box type cmd.exe and click OK
  d. in the command prompt, type the following.

  e. ENTER after each new line.
  ipconfig/flushdns
  ipconfig/release
  ipconfig / renew
  output

  Method 3:

  This problem may be caused by incorrect DNS settings. following these steps and check:

  a. click "Start", enter "NCPA. CPL"(without the quotes) and press ENTER.

  b. right-click on the connection you use for the local connection, and then click "Properties".

  c. Click to select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.

  d. in the Internet Protocol window, we will change the "Preferred DNS server" to 208.67.222.222

  e. click 'OK' twice to complete the change.

  If the problem persists, please repeat the steps and change the "Preferred DNS server" to 208.67.220.220.

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• Satellite A210-171 - unable to connect to any access point or router

  Hello. I don't know that this is the right forum. Not something I do normally but since I am desperate to solve this problem, I'll give it a shot.

  So I bought a Toshiba Satellite A210-171 nearly a year ago. It has a built-in wireless driver.

  The problem is, however, I can't seem to connect to any access point or router. What I end up getting most of the time are so a message saying that I am connected but with limited connectivity which means I can't access the internet. At other times, the network in range will appear in my network list, (with a signal strength excellent), but once I have select a message appears saying that the connection attempt has failed. And at other times my laptop detects the network connection and functions smoothly.

  I do not understand of course. So if someone could explain to me why my laptop selects and selects Wireless connections, that it connects and how I can solve this problem, I would be grateful!

  Thanks in advance

  Have you tried to update the driver on your laptop?
  Check the Toshiba site for an update:

  http://EU.computers.Toshiba-Europe.com > support & downloads-download drivers online

  And if you are already on this site check for a BIOS update.

• Unable to connect to the access point.

  Original title: Wireless list - refresh time

  Hello

  I have a question. Due to my company some Access Points located to everywhere, and all use same SSID and network key, so that we can connect to the network without a problem.

  But when my computer to move from one place to another, then it will connect to other Access Point, but it will take a lot of time to re - connect to the second APs. When I click on the "Refresh" to update the list of network, it can connect immediately to the nearest AP. can I know y at - it a setting I can put so that PC capable of scanning wireless network every second or every minute?

  Help, please...

  Hi Swee,

  I suggest you to post the question on the link below. This is the link from TechNet Support for networking. This team is the team dedicated to the issue that you are facing. They will help you better.

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Feel free to write us if you encounter problems with Windows.

• After running Thinkvantage System Update, unable to connect the wireless access point

  I've recently performed Thinkvantage System update for updating various programs/drivers on my T61p.  I've updated the V5.12 access connections.  In addition to this I was required to update driver V1.52 power management and functionality of the shortcut key for

  V2.10.0002 (two of them were the most recent available).

  After these updates, I can connect is no longer to any access point wireless that worked before this update.  I have tried to reinstall earlier versions of Access Connections, but still couldn't connect to wireless access points.

  ANY help would be appreciated.

  OK, problem solved.  I found that when I ran last weekend system update downloaded and installed an incorrect driver for my wireless hardware.  I installed the correct driver and now the connection to a wireless access point works.

  Certainly, I don't understand how/why not update system would be to download and install an incorrect driver.  VERY FRUSTRANT and TEDIOUS!

• Power Save Polling (PSP) leads to problems in connection with some access points

  Symptoms:
  The following symptoms may be seen if an access point Wi - Fi (AP) or router Wi - Fi broadband does not properly support the Power Save Polling (PSP) feature:

  • Intermittent loss of Wi - Fi
  • Unable to open a connection Wi - Fi
  • Poor Wi - Fi connection data performance

  These symptoms may be more pronounced when on battery.

  Cause:
  The PSP mode is a feature that provides the long battery life for laptops. It requires coordination between the AP or router and the Wi - Fi adapter. Intel has discovered that some APs or routers may not implement the feature correctly or completely.

  Socorro

  Heard different things people try, depending on their wireless adapter.

  Start, control panel, device, netowrk, their adapter, power management Manager. Clear the checkbox to allow windows to turn off this device to save power

  Start, control panel, device, netowrk, their adapter, advanced management. Looking for antenna diversity. Some cards have it and others don't. Replace the Auto antenna by supply diversity

  Some have disabled Wireless N of their card and achieved good results.

  Some Wireless N adapters operate ONLY on the 2.4 GHz frequency.

  Using these parameters of the recommended wireless router I use channel 11, have GREAT results. I usually recommend creating a new SSID to make the connection easier. Wireless devices also needs to connect to the NEW network.

  Rick

• Droid Turbo could not connect the Cisco access point

  Greetings.

  Since the upgrade to a droid turbo, I was unable to connect to the network without wire of my work. I work in the it Department, but my experience with Cisco technologies and wireless is limited, so I tried to understand why. My previous bike x worked fine. We have a network of all the access points managed by a controller Cisco 4402 running version 7.0.98 of the BONES. I was able to connect to another wireless network that I could meet outside of work, and I am able to connect to the network of my work if I connect it is unsecured guest SSID. Only connections to our 4 secure networks fail. The controller reports that my phone cannot all simply to authenticate. The controller is configured for WPA2 / AES using a key 284 on the particular network, that I am trying to connect. I entered this key manually both via copy and paste. As far as my phone goes, I only tried to withdraw and time networks like tent to start it in safe mode without success. I read on various forums android that maybe it's a problem related to Kit Kat and this kind of problem has appeared on other handsets from other manufacturers, but nothing definite.

  Any suggestions would be much appreciated.

  -Josh

  Let me direct you to two other discussions here on the Droid Turbo forum and the other from Cisco which may help.

  Unable to connect to company wifi

  https://forums.Motorola.com/posts/af633eb3e4

  DROID WiFi Turbo questions

  https://forums.Motorola.com/posts/06a2f3c5ca

  Connectivity issues with Cisco and Moto X (Gen 2) allowed RMC controllers (probably related)

  https://supportforums.Cisco.com/discussion/12331486/connectivity-issues-Cisco-controllers-and-PMF-enabled-Moto-x-Gen-2

  I hope this helps!

• Cannot connect Blackberry mobile access point using Windows computer.

  Original title: connection problem

  I use windows 8 on my hp15 and also a cell phone blackberry q10... I noticed that the hotspot from my phone does not appear on the windows network. but hotspot of the else phone shows and connects perfectly well and my q10 hotspot shows and connects on their own computer... any idea on what could be the problem?

  Hi Adam,

  Thanks for posting the query on Microsoft Community.

  If I understand correctly, you are unable to connect the mobile access using Windows computer point. Don't worry, we will help you with the question. It could be matter of settings.

  Manage the network and other utilities mentioned in the link below and check if it helps.

  Why can't connect me to a network? :

  http://Windows.Microsoft.com/en-us/Windows/cant-connect-to-network#1TC=Windows-8

  Also try the other steps in the link below.

  Mobile broadband from end to end:

  http://Windows.Microsoft.com/en-us/Windows-8/mobile-broadband-from-start-to-finish

  For reference:

  http://BTSC.webapps.BlackBerry.com/BTSC/ViewDocument.do?externalId=KB31857&sliceId=2&DOCTYPE=KC&noCount=true

  http://docs.BlackBerry.com/en/smartphone_users/deliverables/55574/mes1342811963579.jsp

  I hope this helps to solve the issue. If the problem persists, get back to us. We will be happy to help you.

• "The connection between your access point router or modem cable, and the internet is broken"

  It is a constant frustration for me sorce. My office gives me this error at least once per hour. I changed the wireless pci card (old one finally died but managed to stay in line!) to a usb dongle, and then to the diffenert pci card, and now I'm in a usb port, which is the same brand as the map oringal that worked. As it is, I can be online long enough to get hope and then... Poof nothing.  I do clean boots, refreshed earworm, did the whole ' IVF it ' was bound to him on a previous post, the netsh command reset. Nothing did. I know that's not the router because all other computers in the House including my laptop can connect.  What Miss me?

  Any help would be loved!

  Hey Tyler,

  Thanks for the reply and keeping the status updated. I appreciate the troubleshooting that you tried it on the computer.

  The issue could be a conflict of others on the computer.

  I suggest you to check the problem in Mode safe mode with networking:

  http://Windows.Microsoft.com/en-us/Windows/Start-computer-safe-mode#start-computer-safe-mode=Windows-7

  If you can't find the problem with Safe Mode with networking, I suggest you perform a clean boot on the computer and check with the question:

  I suggest you follow the link below to find out how to place the computer in a clean boot.

  https://support.Microsoft.com/kb/929135

  Note: Reset the computer in Normal mode once you have completed troubleshooting as a result of the "How to reset the computer to start normally after a boot minimum troubleshooting" section of this article.

  Just reply with the results. I'll be happy to help you.

• Windows 7 or 8 shows the wireless client connected to the access point, but the wireless icon displays "no internet connection".

  I saw the same problem with a different providers wireless solution. When I've sniffed the air with OmniPeek and the network that the ap was conducting with WireShark, I see the arp for the gateway request going to the router, the router gateway response is sent to the suspect machine in the air, the acknowledgement of PC than the package but never fills the arp cache. I watched two arp responses in a vs work for lack of scenario, the two packages are the same.

  The only way I could solve it was to disable IP Helper (not start too) services, reboot the machine. I see 3 to 4 drops per day, but since the deactivation of this Service the machines with that I tested have not seen the question once again.

  IP Helper:
  Provides tunnel connectivity using technologies of transition IPv6 (6to4, ISATAP, Teredo, and Port Proxy) and IP-HTTPS. If this service is stopped, the computer will not have the benefits of improved connectivity offered by these technologies.

  Machines tested and fixed:

  Lenovo E540
  Lenovo W540
  Acer Aspire One
  Dell Latitude E6420

  Ip assistance service has been changed about 40 laptops, a dozen of which would fail in about an hour. So far, 0 out of the 40 saw the question since this change and reboot (reset is the key after disable it) laptops. It's been about 5 days.

  Any reason why disable this Service solves the problem? With it I can replicate the problem pretty quickly on a few different types of machines so it seems not to be driver or provider specific wireless network card. I checked through the Event Viewer logs, but nothing seems to be triggered during the show. Using the Troubleshooter or disconnect the wireless service will fix the problem for a short period only.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?filter=AllTypes&sort=lastpostdesc&brandIgnore=true

  Hope this information is useful.

• Error IRQL_NOT_LESS_THAN_OR_EQUAL when I try to connect to wireless access points

  I get this error IRQL_NOT_LESS_THAN_OR_EQUAL whenever my wireless adapter is turned on or I re - enable after I disabled it to stop the BSOD happen at startup.

  Here are the scenarios in which it happens:
  (1) when I turn on the laptop and the wireless adapter is enabled; It gives the blue screen and restarts.
  (2) once it has been restarted since the first scenario, I have trying to move from a point of wireless access to the other.
  (3) the wireless adapter was disabled before closing, when I turn on a connection attempt, but it shows all the available connections and I try to solve problems, blue screen back again.

  Other information:
  I do not have any material change. I use the Windows 8 operating system. I use the HP Envy m4.

  Also, when it starts later, my screen remains black at any time from 1 to 5 minutes.

  I find that I use my PC because of the frustration of the far less.

  EF

  These accidents were related to the corruption of memory (probably caused by Kaspersky).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You need not run memtest again unless you want to.

  If you are overclocking anything reset by default before running these tests.
  In other words STOP! If you don't know what it means that you're probably not  
  
  
  
  
  1-Driver Verifier (for full instructions, see our wiki here)
  
  2-Memtest. (You can learn more about running memtest here)

  
  

• The connection between your access point, router or cable modem and the Internet is broken...

  -router

  connection internet dropmy every 20 minutes and again after one minute everything is as before... pls help has me... mb my router is a waste

  Wire? Wireless? Status of other computers (if any)? Router? Network devices? Type of Internet connection?

  Have you other computers can connect to the Internet using the same network hardware?

  You have any kind of 3rd party Network Manager installed, like Hello, Netmagic and the likes?

  Do you have the "Fancy" 3rd part security suits, or as the hybrid of nVidia Firewall Firewall.

  You are using more than one firewall (including native Windows), AV or other security applications active?

  If you use any 3rd part above, try to configure them to work corretly on your network, or get rid of them and see if it helps (RID, means getting rid, not just disable ).

  ------------------

  Assuming that you are connected with the wireless to the router.

  First scan the computer against the viruses and Malwares.

  When you are sure that it is clean.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• My blueray DVD fails to connect to the access point

  I have a blueray player which has wifi.  Whenever I try to connect to the network that it fails.  I see the available network connections and put in the passwords, but it will still not connect.

  Hello

  What is the number and the model of your Blue Ray player?

  I recommend you contact the manufacturer of your Blue Ray player, and I'm sure they will help you solve this problem.