Port mirroring for the uplink of 10 GB of PowerConnect 6224
I need to take a copy of the traffic over a 10G fiber link. The amount of traffic on this link is less than 1 Gbps.
I am considering using the mirror port on a PowerConnect 6224 for this function. However, I don't know if port mirroring also works on the links to the top of the switch.
Anyone know if a port 10G uplink on the 6224 can be mirrored on one of the 24 Gigabit Ethernet ports?
I've been the mirror of able port of a fibre port with an Ethernet port, following the instructions on page 333 of the owner's manual.
http://support.Dell.com/support/eDOCS/network/PC62xx/en/UCG/ucg_en.PDF
He took it and did not return any errors. But I see potential for some issues if the fiber port went above 1 Gbps.
Keep us updated and let us know what are your conclusions.
Thank you.
Tags: Dell Switches
Similar Questions
-
Consolidation and failover for the uplink on the Distributed switch port group
Hello
I have a problem with the implementation of a distributed switch, and I don't know I'm missing something!
I have a few guests with 4 of each physical cards. On the host eash I configured 2 virtual switches (say A and B), with 2 physical network by vSwitch using etherchannel adapter. Everything works fine for etherchannel and route based on the hash of the IP for the latter.
Recently, I decided to create two distributed switches and move the respective physical ports of virtual switches to this distributed switches. Once again, I want to configure etherchannel and route based on the hash of the IP. But when I open the settings for the uplink port group, aggregation and failover policies are grayed out and cannot be changed. Apparently they inherit configuration also but I don't know where!
Chantal says:
Once again, I want to configure etherchannel and route based on the hash of the IP. But when I open the settings for the uplink port group, aggregation and failover policies are grayed out and cannot be changed. Apparently they inherit configuration also but I don't know where!
You must set the card NIC teaming policy on trade in reality and not on the uplink group more expected.
-
Error: Could not find the WSDL port defined for the Service
Hello
I am facing error below when calling the partner WSDL:
Oracle.Fabric.Common.FabricInvocationException: Cannot find the WSDL port defined for the service.
Can someone guide me what could be the exact problem?
* I can't ping this host.
Thank you
Richa
Puneet salvation,
I am able to access from the WSDL browser and value of the location in composite.xml is correct.
Kind regards.
-
Port forwarding for the suddenly closed Linksys router
I have a 54G wireless router... correctly port forwarded a request of a CPU (server)... but after no connection made by the user on the server... it suddenly close the application... so what I did is to reboot the router in order to refresh the connection...
Are there other ways to fix this sudden closure of ports? so that I would more restarts on my router
I appreciate a lot of help...
As directed by your statement the port that you have passed on the closed router without any connection to the server is unusual. Please make sure that you have configured an IP address static (outside the range of the router DHCP) on your server and put the same IP address for the specific port port forwarding tab.
In addition, reduce the MTU size on the router to 1400. See the link below on how to make the changes in the MTU size.
-
printing image mirror for the HPphotosmart 7525
Help!
I have a HP photosmart 7525 on a PC using windows 7... for the life of me I can not understand how to document & print (t-shirt) of him... Have tried everything I know and nothing works so far. any suggestions?
Hello
Its pilot, many do not support flip. Many software programs allow you to rotate the image before printing. Please check step #8 of the following article:
or try the following method (does not work on all printers):
http://support.HP.com/us-en/document/bpu02032
Kind regards.
-
change port number for the mobile server after installation
Jin
I use windows 2003 server release 2, Server Oracle 11 g R2 and oracle database lite 10g R3. I installed successfully the mobile server with port 80, but when I start the mobile server I get an error message indicating that port 80 is already in use. Now, I need to change the port number of the mobile server. can someone tell me the solution.If the Oracle Lite installation type is INDEPENDENT, then to change the port number of Olite in any other available free port number, you must edit the file by default-web - site.xml or site.xml - web-http file present in $OLITE_HOME/mobile_oc4j/j2ee/mobileserver/config directory.
You can at any time change the port in the file http web - site.xml and bounce services, the new port will take effect.
-
Tool for mirroring for the direct Selection in Photoshop tool?
Hello
I'm working on a new logo, it will be a shield.
I used the custom shape tool and changed the shield in the way that I like (on one side, with the direct Selection tool).
But now the shield no longer symmetrical.
(extreme situation of photo)
Is there a function to change (for example), the shield and keep it symmetrical when editing of the shield?
Sorry, my English is not very good =-)
Hello, I don't think that there is. My suggestion is:
-divide the form into two parts, so that you can have half of it. To do this, use the direct Selection tool, select the first high point of the page to the right and remove it
-After you finished your edit, duplicate and mirror of your form. To do this, you can select all your vector illustration with a direct selection tool and press HUMINT + C then Ctrl + V (copy and paste)
-Drag your new shape on the right and mirrored by using path editing/processing / reflects
-Drag the shape of your half on the side of the first.
-
Port number for the switch Cisco 4503
Dear Sir.
When there is a power outage our router to pass link would not come, we must reset switch port all the time, so we are facing a problem as it is a remote site, all the time, that he must go to reset the port. So I hope your kind response to this problem.
Switch - 4503
Router - 3725
The link is layer three.
Best regards
Before the port is reset, which is the full output of the command 'sh interface status error "?
-
Need help with the port forwarding for a XBox remote Streaming
I have a router R6200v2 and need help with port forwarding.
I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere
http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/
I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.
Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?
Hi @varxtis,
You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.
1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)
2. Select the type of service (TCP, UDP or both)
3 entry 5050 times a start external Port and external endpoints.
4. Select the IP address of your XBOX.
5. Select apply.
6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.
Kind regards
Dexter
The community team
-
Hello a good person.
Is a UPC (Unified Port Controller) of the FI 6200 supports multi protocol ports simultaneously?
For example, the second UPC has 1/9-16. Configure the ports like these? 1/9-10 for the server ports, 1/11-12 for the uplink ports, 1/13-14 for FCoE Uplink ports, 1/15 and 16 for the Uplink FC ports and so on. I know that Cisco Documents describe a port can be configured as server port, FC, FCoE... I "don't not interesting in these gross comments."
Thanks in advance.
Paul
In UCS unified configuration of ports is controlled by a scroll bar, as shown here.
There is a fixed configuration for FI ports, then another to the expansion Module. FCoE and Ethernet ports are both type Ethernet from a unified point of view port, CF requires that you select the ports you want to be FC ports.
All ports to the left of the slider bar will be Ethernet, which can also be configured for FCoE, and everything to the right will be CF. So to answer your specific scenario above Yes. BUT with a caveat.
If you have moved the cursor between port 14 and 15 then left would be Ethernet can be configured as a Server Port, Port Uplink or FCoE port and ports 15 and 16 could be configured as FC ports. BUT the downside would be that ports 17-32 would also be FC ports and you couldn't get to the Ethernet ports later. If the port configuration is adjacent to ports on fixed ports, as well as on the extension module.
Best practice is to determine how many FC ports you need and configure each component accordingly.
Here are some details on the guidelines for the unified configuration of Ports.
Hope this helps,
Steve McQuerry
UCS - Technical Marketing
-
Port number for a manually created database
Hi all
I have an original database installed using the installer regular Oracle on the default port 1521.
Then I created the PeopleSoft database by using create database command. I aksed never of port number in this manual steps. Now, im in the process of setting up Enterprise Manager, here I need to enter the port number. IM wondering would it be same as initial database 1521... or? where can I see this information.
Thanks in advance.RamaN says:
Hi allI have an original database installed using the installer regular Oracle on the default port 1521.
Then I created the PeopleSoft database by using create database command. I aksed never of port number in this manual steps. Now, im in the process of setting up Enterprise Manager, here I need to enter the port number. IM wondering would it be same as initial database 1521... or? where can I see this information.Raman,
I think that there is a confusion of a lot of time that you are experiencing. First of all, 1521 is not the port number of the EM (its not supposed to be) but for the listener . So don't really use you it for something else, and just for the listener, and there is a single earpiece only which should be enough for all of the databases, you have. For the initial data, the default port for the EM, is 1158. This can vary according to the configuration you have. There is a file that is created and stores all the ports used in the parties initials, portlist.ini . It would be in your ORacle home. You can see the port number used by the MS of the initial database from there. For the manual creation of the MA, Oracle will ask you the port number for the listener, not where it must run the MS. If you enter 1521 only.
HTH
Aman... -
Mirroring of the ports on Dell PC 6224
Hello
I'm trying to implement Port Mirroring on a PC 6224.
The Setup Guide, I read 'You can configure several ports as source ports switch and port of a switch as a port of destination.'.
But when I try to add a fifth port source port mirroring, it returns the message "no port source more can be added."
session mode 1 #monitor console (config)
Console (config) #monitor session 1 destination interface 1/g24
Console (config) #monitor session 1 source interface 1/g1
Console (config) #monitor session 1 source interface 1/g2
Console (config) #monitor session 1 source interface 1/g3
Console (config) #monitor session 1 source interface 1/g5
Console (config) #monitor session 1 source interface 1/g6No more of source ports can be added.
Console (config) #.
Someone has experienced the same problem? Is there a limit in the number of source interface?
Thank you
Hello
The number max of ports that can be configured for duplication of port is 4. I am always checking if change the firmware will allow more to be configured & will report once I have this extra info.
Let us know how it goes
-
Question on the uplink ports 4507
Hello
The contractor for the 4507/4510, the 8th, a 8 GB 10 uplinks. Agree these uplinks as access to servers or VMware hosts ports, or are they only for inter switch links?
Thank you
Waqas
Hello
You can use them for what you want. They can connect to the virtual machines, stand-alone server, workstation, inter-switch etc... They can also be access or trunk ports.
HTH
-
stop the ethernet uplink port will cause the port of the unit down
Dear all,
I want to make sure that this kind of network traffic will communicate internal fi.
I've disabled the uplink port and found the path of material has also declined.
Port of the device must road toward uplink port and then back to UCS server?
Thank you for the clarification.
Best regards
Dennis Dai
Expected behavior. By default, if there is no uplinks online & fwd, then all links South (Server binds and the ports of the device) will be used also to the bottom.
See the explanation of Abi here for more information how to change this behavior.
https://supportforums.Cisco.com/thread/2187144?TSTART=0
In short, we must change policy control of the network of the way of the material in the Hardware tab.
Kind regards
Robert
-
4 FC by FI uplink ports. But what a single port to send the addresses of WWPN vHBA?
I have four portis configures as uplink FC by FI and FI woking in end host mode.
I have 24 blades using two vHBA. vHBA0 and vHBA1.
24 address WWPN are saved on the uplink of SAN of only 1 FC uplink.
Same case in the other Brocade.
That is something we don't want.
All FC uplink ports must be used.
We have borcade. Advised not to use the port channel.
I can manually create groups of pin code and balance the load. But do create a lot of model vHBA and tedious work.
Other autour work?
Help, please.
(1) you can only use Port FC channels connecting to Cisco MDS and Nexus or for FC traffic.
(2) on each FI, run the following command:
(nxos) # see the npv flogi-table
You should see the WWPN by connecting to the FIs, or you have problems downstream with your configs vHBA.
Make sure that vHBA0 is mapped to FI - A and vHBA1 is mapped to FI - B and the proper vSAN is assigned to the vHBAs. Also ensure that the FC connections are not crossed the FIS for the brocades.
model vHBA allows very simple, consistent deployments.
Maybe you are looking for
-
How can I disable the onboard sound card in BIOS on the Equium A200
I use an external Creative Sound Blaster sound card, but the recording level is very low and were advised by Creative to disable the onboard sound in the BIOS but there is no option to do this. Can anyone help?
-
Qosmio F30 - installation of Windows XP is not recongize the HARD drive
Hi all, can you help me please? I had a virus on a download tried to get rid, but all not so tried to format the HARD drive and reload XP pro by putting in the disc and the loading, but find no hard drive after many attempts. So I removed the HARD dr
-
Qosmio X 500-116 will not play blue-ray discs
Hello world bit of a newbie on laptops but my Qosmio dvd player won't play Blu - ray movies using the "Toshiba DVD Player", although it will play normal DVD movies no problem. I use the wrong software? search through programs pre-installed, I as ' nt
-
HP pavilion 15-e005so windows 7 drivers bluetooth
I can't find driver controller bluetooth to hp pavilion 15-e005so windows 7 any where can you help?
-
Update KB2572075 product code 80070020
Update KB2572075 product code 80070020. I tried various 'clean' departures and still not get this update to install. I can't ignore it because my security system keeps scolding me. Please notify