Portege 2000 cannot start after suspend

Similar Questions

• Mac cannot start after el captain

  Cannot start after updating mac

  Safe Mode boot removes the system caches that can help after an OS X day or level.

  Follow these steps to start in safe mode.

  1. Start or restart your Mac.
  2. As soon as you hear the startup tone, hold down the SHIFT key.
  3. Release the SHIFT key when you see the logo Apple appears on the screen.

  After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

  To leave safe mode, restart your computer without pressing any keys during startup.

  Try safe mode if your Mac does not end commissioning

• Portege Z930 cannot start with installed RAM module

  My laptop Toshiba Portege Z930-108 has stopped booting with any module of RAM installed in the support.

  If I remove RAM module, laptop computer starts and works fine, but if I install any module of RAM (4 GB 1600 original or a new 4 1600 CL9 or 1600 8 CL11) the computer cannot start.

  The screen stays black and power led flashing two green and two orange and a few seconds later, 3G indicator also on blue.

  This is the only problem I have with this computer, but it's strange.

  I updated the BIOS to the latest version and the problem is not resolved.

  I tried to reset the hardware (http://aps2.toshiba-tro.de/kb0/TSB3B03J90000R01.htm), also I tried to reset the equipment with power button 30 seconds without battery but button without success.

  Any idea on this problem of strage?

  Kind regards
  Lito.

  I guess you used bad RAM or not fully compatible modules.
  It's the only plausible explanation.

  I recommend you to order the RAM modules recommended by Toshiba that are:

  4 GB DDR3 - 1600 PA5037U-1M4G

  2 GB DDR3 - 1600 PA5037U-1M2G

• 'Comfort Curve Keyboard 2000' cannot start (code 10)

  Hi, my laptop cannot detect my external keyboard. The keyboard is the 'Comfort Curve Keyboard 2000'. Laptop is an ACER ASPIRE 5738 G running Windows 7, 64-bit, the publishing house.

  When I plug in the keyboard, Windows says it can't find a driver for the device and if I manually select HID keyboard driver, Windows indicates that the device cannot start (code 10).

  I already tried to uninstall all USB devices and restart the system, but it did not work.

  Any suggestion?

  Hi Stefano,

  If the device has a FailReasonString value in its hardware key, that string is displayed in the error message. The driver or enumerator places this registry string value there. If there is no FailReasonString in the hardware key, you receive the following error message.

  Explanation of error codes generated by Device Manager in Windows XP Professional

  http://support.Microsoft.com/kb/310123

  Follow the steps to solve the problem of hardware in the computer:

  Method 1: Run the fixit to solve hardware problems:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 2: Check the boot to find that there is no conflict applications/programs:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: When the diagnosis is complete do not forget to reset the computer to a normal startup.

  Please contact the Microsoft Hardware support:

  http://www.Microsoft.com/hardware/en-IE/p/comfort-curve-keyboard-2000#support

  Let us know the result.

• Cannot start after the blue screen "page in the nonpaged area failure."

  My sons laptop has got to me.  There the error page blue to come with "failure page in the nonpaged area." There is a chain of technical info of numbers, but this changes a little at each attempt.

  I tried all F8 options, without success.  I did a restore disk from the laptop of my other son (which is the same) and that has not worked and I also downloaded a file of system restore on the internet who do not.  I ran diagnostics memory on the scope option and who found nothing.

  No matter what I try, always the fails to start after the first screen with Microsoft Corporation at the bottom and the small lights of scrolling!

  I would be grateful for any suggestions that anyone can have.  I wondered if I should try to borrow a disc of Windows Vista from someone and try from there?

  Read the messages and follow the procedures established by the MVP of the spirit in the following thread on the Blue Screen of Death.  They should help you solve your problem. http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/8cd8362e-7d06-46fb-afd7-84d54b6a8ea7.

  I hope this helps.

  Good luck! Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Code 10 device cannot start after Windows update.

  Original title: had this application update 26509 operation message

  I hope that I chose the right place for this question

  By PAD so I give you all the unusual things that have occurrred recently

  When I clicked shut off (to turn off the computer) last night I received a message something like this but this isn't verbaitim.

  -apply the updates do not turn off or disable... Let him go was not a thing then it shuts

  This morning from my computer (windows 7) I see a lot of numbers flight by update of something... Finally he stayed still long enough to read this message

  ' application operation update 26509 26509 (\Registry\Mach...) . who took about 90 dry

  then the screen changed to say prepare to set up windows (while I was getting a large piece of paper to write it down in my computer I went back to what is normal for my computer open) he says treatment auto - VGA - the screen is black for 2 seconds and my office is open and functional.

  --------

  Please lmk if I should post this separately if it is not part of the above problem

  OK not to confuse things and maybe it's not bad but I will also attach additional information... Thank you for your patience.

  Sometimes messages arrive on my screen and went so fast that I don't know what they said and that's what's happening all I saw were collected WAN miniport (ATW) #2. and something that affects the usuage of my computer... I went to the Device Manager and under "Network card" was a green line to see, I opened 2 inputs was the first

  "Intel (R) 82578 DC Gigabite Network Connection" under properties it says that this device does not work correctly

  the second entry "WAN Miniport (ATW) #2 * was a yellow triangle with a point of exclamation and under properties say this device cannot start (Code 10) .

  I'll wait on this case its not important right now with my orogonal above problem

  Thanks again for you time and patience... looking forward to your entry

  Learning to 62 (aka granny)

  Hello

  1. have you successfully install the update?

  2. are you able to connect to the desktop without any problem?

  Was the message you saw before Windows starts, the system applying these updates. This is a normal procedure that Windows takes above all the critical updates are applied. If you were not able to start Windows, then we might have a problem with Windows update.

  Regarding your second yellow exclamation on the wide area network WAN miniport, you need to update the driver for the network adapter.

  The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues. You may need to update the chipset drivers and the network adapter.

  I suggest you run the automated FIXIT from the link below and.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  I would say as update you the driver for network card and check.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• Cannot start after the formatted NTFS partition

  Option to boot OS X suddenly absent after that I formatted the partition NTFS (bootcamp) of Windows installation.

  

  I read many previous question in many Web site and

  I tried to fix it in disk utility, but it cannot go up more.

  user mode single launch I tried, but it does not start.

  already reset NVRAM and SMC.

  Is there not any solution to start again or access my files in the partition mac to back up?

  Thank you.

  Somehow, you managed to format your OS X with making it unusable NTFS volume. I recommend you do the following:

  Clean Install of El Capitan

  Restart the computer. Immediately after the chime, press Command + Option + R until a globe appears.

  The Utility Menu appears in 5 to 20 minutes. Be patient.

  Select disk utility, then click on the continue button.

  When loading disk utility, select the drive (generally, the entry Out-bumpy) in the list aside.

  Click the Partition tab in the main window of disk utility. A panel will fall.

  Set the GUID partition scheme.

  Define the type of Format Mac OS extended (journaled).

  Click on the apply button, then click the fact when it is active.

  Quit disk utility and re-enter the Utility Menu.

  Select reinstall OS X and click on the continue button.

  This should install it the version of Mac OS X that has been previously installed when the computer was new.

• Cannot start after WinXP disk Image resizing

  I am running Fusion 3.0.1 and tried to resize my Windows XP image (actually my main motive was divided into 2 GB files, so I checked this box and move the slider to the top of a few GB).  I started by removing my snapshots.  Everything seemed to go well and it took about 10 minutes to clean files, but after resizing, I can't start (and have of course no snapshots to come back).  I have the hard drive, select as my entry, but merging does not seem to be seeing and seems trying to boot to a network device, and after a few seconds I get a message that "no boot device not could be found.  I always get the resized image of Windows XP with the VMDKMount utility, and everything seems to be intact.

  Any suggestions or advice?

  See you soon,.

  Peter O.

  PeterO2 wrote:

  Now, back to my original goal of trying to divide it into 2 GB files to facilitate backups.  Do you think I should make a backup copy of the image before I try the thing resizing again?

  In general I ever preform at a disk level operations such as resizing without first making a copy of the target computer virtual package with her judgment, not suspended and the merger closed however if you still have the version of Parallels you can always create another import if necessary but if you no longer have the version of Parallels, then I'd do a copy before proceeding.  Also, make sure that you have enough disk space before you start the process.

• Portege 2000, cannot install windows, ide errors

  Any help much appreciated...

  former owner deleted the 20 GB hard drive. Have the Toshiba pcmcia reader. Flashed the latest bios. It will boot xp or 2000 cd without problem, however the two OSs stop initially with bsod (2000 gives inacessible_boot peripheral).

  Tried with ME, but the cdrom driver is not the right one (does not load the cdrom drive). In a situation like this, normally, I remove the drive and install (with hard drive adapter) on a pc to format and copy the OS files and then reinstall the drive and start the installation from the hard drive but it has a 1.8 drive "and I have no adapter.

  Help!

  Mick

  Hey Tyson,

  Sorry, but I'm a little confused about your explanation. If I understand you right, you bought used protégé 200 with Toshiba external CD-ROM device (PCMCIA) and you try to reinstall?

  I understand you correctly?

  As much as I know in original Toshiba Recovery CD there is driver for external "TOSHIBA CD-ROM" (PCMCIA/CARDBUS) and it will be loaded at the beginning of the recovery procedure. If it works with no Toshiba devices is unknown to me. If you want to reinstall the OS without the original CD from Toshiba, you must start the laptop using the startup disk with the right driver for external device.

  As you said that the best solution is to start the installation of the HARD disk. You need a Google around and I'm sure you can find one for you. Please visit this site
  http://www.Addonics.com/products/Saturn/aesed.ASP. He is described as the optional kit 2.5 "converter can be used for the 2.5" or 1.8 "IDE HDD.

• Satellite A30 cannot start after cleaning the heatsink

  I have a problem with my sat a30. It lights for 5 seconds then goes automatically off and on again for 5 times, before finally shutting down completely. all this began after I cleaned the heatsink. can you give me some advice for what to do with this problem?

  Hello

  This path is not easy to say what is the problem, because, who know what did you exactly and how. As you know do something like that on your own is always risky.

  Are there signs of life of the cooling fan? AFAIK the CPU becomes very hot in just seconds after the start, and I presume that CPU is not cooled properly and because of this unit turns off.

• a1720n cannot start after the installation of the DVD from LG GGC-H20L drive

  I installed the unit and connected to the second channel SATA (blue) and the computer would not start.  Disconnected and the system returns to normal operation.  It appeared that the system was able to read a correct reader type in the BIOS.  I couldn't find any instructions online documentation SATA configuration.  I will apprecaite the ideas or the BTDT there!  Thansks!

  Thanks for your quick responses!  I advanced and tried to just connect the drive again and the system booted properly.

  When I said that the system does not boot, it would go beyond the BIOS screen but should restart after trying toload windows.  Subsequently an any a GUI recovery came, ather than aloowing system to restore from an earlier time, I told him to try an automatic recovery.  This process was then several minutes before failing.

• Win7 (Home Premium) cannot start after "important update"

  I just bought a new PC with Windows 7 Home Premium pre-installed. After an update that Win7 launch is no longer, instead the PC reboots from the BIOS. Now, as I write to you from my old XP system, I do that I can't do this post shouldn't indicate that I found a solution. Using the utilities available / suggested at this stage, I can't understand what the 'important' update was so am not able to retrace the steps that may have caused problems. Currently, I run the system recovery, so maybe in a few minutes, I might be able to use the WIN7 PC again. However, I would like to know if anyone else is / has been faced with this problem.

  Hi isamart,

  First of all, I suggest to start the computer in safe mode and see if you can boot to the desktop.

  To boot to the desktop in safe mode keep tapping key F8 during restart. Once you see the option to start in safe mode select and press to enter.

  Access the link to learn more about how to start the computer in safe mode: http://windows.microsoft.com/en-US/windows7/Start-your-computer-in-safe-mode

  If you are able to access safe mode, you can try to check the update installed on your computer and remove it and check if that helps.

  To view and remove the updates installed, follow the steps below.

  1. click on start

  2. in the start search box type appwiz.cpl, and then on enter.

  1. click on view the updates installed in the left pane.

  2. take note of the recently installed update in the list and remove the update.

  3. restart the computer and check if you can start.

  If the steps above fail, you try to perform a system restore on your computer to an earlier date and check if you can boot to the desktop.

  To restore the operating system to an earlier point in time, follow these steps:

  1. Click Start, type system restore in the search box, and then click System Restore in the list programs.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  2. in the System Restore dialog box, click on choose a different restore point and then click Next.

  3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  4. click on finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Access the link below to find more information about the system restore.

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  I hope this helps. Let us know the result.

  Thank you and best regards,

  Srinivas R Microsoft Support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Aspire E3 - 112 cannot start after win10 own attempt installed

  The installation is wrong. He went right through the extract process and install OK but then just went along in a loop to keep reinstalling the usb drive. I changed the bios by promoting usb hdd over windows Boot Manager (in uefi). So I removed the USB drive and restored the order of the bios. But now, when I boot, I get an error window saying "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install windows click OK to restart the computer, and then restart the installation. "It makes no difference if I close the window or click OK, it goes through the same circle.

  Help!

  Thanks for the reply. I tried that. In the end, I found that the solution was to wait for the beginning of the (umpteenth) reinstall the process and then press the power button for a few seconds until the machine stops. Then I powered up while pressing the F2 and is gone in the bios where I restored the original and the machine parameters and then started in the new clean install.

  Unless the OS is nuked, how to perform a clean install is using the settings > update & security > Recovery > restart now and use the boot from usb option. And leave the bios alone.

• HP Pavilion DV4-1125nr cannot start after the update/update BIOS version F.12 to d.55

  System: HP Pavilion DV4-1125nr PC Notebook

  Product #: FR922UAR #AB

  The system board ID: 30F7

  Version of the BIOS (before the update): F.12

  OS: Windows 7
  

  I tried to update the BIOS to d.55 which was provided by HP. After the successful installation the closure of new windows BIOS correctly. I restart the PC, HP Logo appears and then nothing happens. The operating system do not load or start at all.

  I also tried to boot using the Windows 98 Second edition CD (to charge BACK), but it did not work.

  Please help me...

  Fortunately I found a Solution to this problem.

  Here are the summaries (and modified according to my needs) the steps that I've taken of the following thread:

  http://h30434.www3.HP.com/T5/notebook-hardware/dv4-1140GO-won-t-boot-after-flashing-latest-BIOS/m-p/19698#M2730

  1. go to the hp site and download the correct version of your BIOS. In my case it had to F.12. Why not the latest version? Because there is no guarantee that the last one will work for you, know after measures.

  2. go where you downloaded the file and using 7 - Zip (or tool of your choice of course) unzip the contents to a folder of your choice. We'll get to that later, so keep this file open.

  3. use 128 MB or no matter what key-USB USB key (the smallest, you might find, because they said the smaller the better ) and reformatted to FAT or FAT32 click with the right button on the drive by clicking on "format".

  4. now that my USB is ready, go back to the folder where you extracted the file to update the BIOS (always open to the right of the folder?)

  "5. If you have the graphics card Intel integrated like me, copy the ' 30F7F12U. FD"of the key USB and RENAME the file '30F7F12U. FD' at '30F7. BIN ". Remember that this name calling to order "DV4-1125nr. If you have a different motherboard, the system or the BIOS, the name must be determined according to the.

  The next steps are exact 0.0 as follows (the link of a full detailed discussion is provided below), I simply numbered:

  6 unplug the adapter from the laptop.

  7 remove the battery from the laptop.

  8 insert the USB key into one of the USB ports on the laptop.
  Does not seem to matter which.

  9. press the 'Windows' key and the 'B' key

  10. connected to the power adapter.

  11 press the 'Power' button on the laptop.

  12. when the LED is entered, letting go of the power button / stop and the two keys down earlier.

  13. After about 10 seconds the notebook started to read the USB key. While searching for the file, the laptop beeps every seconds.
  The number of beeps varied, depending on what size of the key USB has been and
  the number of files on the USB key, a single beep for many.
  If the file was not found, the laptop will restart and try again.

  14. If the file is found then it took about 12 seconds for the laptop to load. No beeps sound not heard during the loading time.

  15. when it is responsible for the laptop has started flashing, indicated by beeps every 2 seconds. It took about 32 seconds.

  16. about 5 seconds after the ringtone had stopped off the laptop computer.

  First I update my pc with the last BIOS (F.66), but did not work for me (operating system not loaded after HP Logo ). So I decided to go back to the old F.12 (the version that has been shipped when the laptop was purchased) according to the procedure described above. But the problem is where to find version F.12 as HP currently provides links only for the version of the BIOS F.66 to d.55 (in the drivers from the hp support site section)

  Fortunately, I found a direct link to this version F.12 in the next thread.

  http://Forum.NotebookReview.com/HP-Compaq/304332-C700-CQ40-CQ45-dv4-dv5-DV6-hdx18t-Insyde-BIOS-recovery-using-USB-thumbdrive-2.html

  F.12 version:

  FTP://ftp.HP.com/pub/SoftPaq/sp40501-41000/sp40749.exe

  This was F.12 and worked for me. Thank God Almighty I return my PC.

  Thanks to all who contributed in the discussions above.

  Kind regards

  -gmuhammad.

  If you think that this post has helped you, then please give KUDOS *.

  Close the thread (Accept as Solution), if your problem is solved *.

• Cannot start after the running virus scan

  I have anti-virus protection McAfee suite through our cable company.  I got a message from windows, my computer has virus.  I did a scan of McAfee and he said everything was fine.  After rebooting my computer, the monitor is just a white screen.  What can I do?

  Hi kahw,

  ·         Did you try to start in safe mode?

  ·         You receive a message during startup?

  You can check if the following is useful.

  Method 1: Use the last good known Configuration in the Advanced Start menu and check if it helps.

  Method 2: Try to start in safe mode and check the number.

  Just reply with the results.