Portege 3490CT - inputs/outputs
I have a problem caused by drivers being removed from the machine according to me. I can't input/output using the external remote diskette, CD Rom, or USB port.
How can I install new drivers without internet access?
Hi Thom,
If you have isolated your notebook all your i/o devices, your only way to restore access will restore your full operating system of your recovery disks.
However, before I do something drastic, that you can try to start in safe mode to see if this will allow you to access your external devices, or you can try to restore your system to a previous restore point (assuming you are using XP) before your drivers has been removed.
HTH
Tags: Toshiba
Similar Questions
-
Portege 3490CT - how to install Windows XP?
I have a portege 3490CT and I want to install Windows xp, but the laptop cannot boot from my external USB cdrom drive. I tried to install Windows on the hard disk on another computer (it works), but if I put the disk in the laptop it does not start.
So, how can I install windows?
Please write back.
Thank you.Hi michaelnachname,
Here you can already find a thread on installation of Windows XP Portege 3490CT:
http://forums.computers.Toshiba-euro...D=16411䀛As you can read, you must format the HARD drive and copy the folder the XP disc on HARD drive i386. Then, you can start Setup from the HARD drive without a CD player. :)
-
Portege 3490CT - turn off problem
My Portege 3490CT began to fade after between 1 and 15 minutes from powering it. It now has a damaged operating system because Windows Update was not able to complete an automatic update. Of course, I cannot locate a recovery CD and do not have a CD Player for her in any case.
Y at - it an easy solution for this problem of sleep and no one know where I can source a W2K recovery disk?
Thanks in advance.
Hi Stuart,
This type of unexpected shutdown is usually related to overheat probably so heatsink CPU having dirty upward with the dust and debris sucked into the cooling fans. It can be cured by clean dust accumulation.
The recovery CD copies are available from any Agent of Service authorized Toshiba.
Kind regards
-
Portege 3490CT - how to remove the hard drive?
Hello
I have a problem with my Portege 3490CT. It is completely dead (won't start not or read from USB floppy to use recovery discs). I would like to remove the hard drive to try to recover the information about it. Can someone tell me how to get out? I already have access to it, but I don't want to damage it in progress...
Thank you
Hello PNVS
You can check this page
http://www.servj.com/PC/Note/hdinstall/Good bye
-
Portege 3490CT: unable to set the brightness of the screen
Hello
I recently acquired a Portege 3490CT and have installed Windows XP on it. Everything works fine except that I can't adjust the BRIGHTNESS of the screen. I believe that this can be done via the software, which does not support Windows XP.
Does anyone have any suggestions? I can adjust the BRIGHTNESS in the BACK using TSETUP, but Windows seems to get around any setting that I'm doing here.
Thnaks in advance.
Hello
To use this feature, you must in particular drivers.
This device has not been delivered with Win XP and I also found this driver in particular on the Toshiba driver page.
I guess, if you want to use the WinXP renounce this function. -
Definition of screen Portege 3490CT
Hi, I am unable to use the full screen on my Portege 3490CT that there is a white border, approximately 1 inch in width, all around. I guess it could be a driver problem and tried to reinstall it but noavail. Any ideas?
see you soon
Ian.Hi Ian,
You can try to reinstall the graphics driver! The current version is available at https://eu.computers.toshiba-europe.com - Driver download.
Bye Bob
-
No sound on Portege 3490CT with Windows XP Home edition
Hello
I bought a Portege 3490CT on eBay. Everything works fine except there is no sound available. I use WinXP SP2. I know there is a problem with the service packs, but the same problem exists after installation of Windows XP without service pack: it seems to be, that there is no audio devices available. The Windows Device Manager indicates only something a device "legacy". I think that it does not find the real device of Yamaha.
Install the new driver of Toshiba homepage gives only a "driver not installed" error message.
In the BIOS there is no option to disable the sound equipment.
It is perhaps damaged?I hope someone has an idea...
Thank you and best regards
MirkoUsually the legacy term device is used to refer to any device that is not Plug and Play compatible.
I can only suggest why it doesn't and I think it s a driver problem.
The sound card that is installed on this laptop is compatible with Sound Blaster Pro and Windows Sound System.
The computer uses a YMF744B. The YMF744B integrates master audio bus PCI, 64 optical interface of synthesis wavetable, AC-2 interface and control AC97 CODEC.
In case you would recommend for Yamaha YMF752 or the driver that supports the chip YMF752 you are looking for the most recent driver.Check this box:
http://www.softwarepatch.com/utilities/Yamaha-acxg-driver.html -
Focusrite scarlett 2i4 unable to use as audio input/output device
I just bought a Scarlett 2i4 hoping that time would have been solved compatibility problems. However, I'm unable to use it as an input/output device. Site Web Focus rite has a class compatible mode download that is supposed to solve this problem. And I installed it three times without success. Has anyone else had this problem and found a workaround. Thank you! I have a macbook pro mid 2012, el capitan 10.11.3.
Don't know if this will help.
I have a 2i2. When I got it, a few BONES in there, I couldn't make it work. I went back and forth with tech support Scarlett. They really tried, even sent several beta drivers. Nothing works.
Then I uninstalled all the software of Scarlett and restarted - and it works.
-
Portege 3490CT: operating system cannot detect the wireless network card
Hello
Portege 3490CT with windows XPProblem: Try to install the wireless lan card. Windows is not able to detect the new hardware.
Details of LAN card are NETGEAR 54 Mbps, model WG511v2Specifications for lan card
It is 16-bit PCMCIA and CardBus 32-bit compatible and works in any available PCMCIA or
Location CardBus. IEEE 802.11 g and b standard wireless technology.Specification for laptop Portege
PC card slot supports two Type II or Type III PC cards; R2.01 PCMCIA, CardBus, PC Card16all tracks on this will be very useful
Best regards
AshwaniHello
What the BIOS has been installed on your laptop?
If you use the Toshiba BIOS so there could be an option called configuration of the device.
(it s is available on my Satellite)You change the option for all devices, you will be able to change the PC Card controller mode. I think you should play a little with this option.
In other cases, the user was able to resolve a similar issue by changing this option.Please report if you re successful because it would be very interesting for me.
Good bye
-
How to upgrade output during input/output synchronized?
Hello
We use an input/output series card m PCI-6289 to provide participants sound while recording the EEG.
Our inputs and outputs are synchronized using the diagram that is attached.
To date our output audio segments have been relatively short. However, now we want to output sounds which last a long time. I've run into shortages of memory by using the current diagram.
Could someone suggest how I could update the audio output, regularly with pieces short 1 sec, in the loop in the diagram attached?
I tried to move the DAQmx Write.vi (point 4 on the diagram) inside the loop, but the output signal was not correct.
Thank you very much for your advice!
Frenk
Hi Frenk,
Can you be more specific about the error that you are experiencing?
Have you heard of the regeneration of analog output? It can be used with a property DAQmx writing node.
Regeneration is the repetition of the data already in the buffer. Standard regeneration is when the PC buffer data are continually downloaded on the FIFO to write. If the data buffer is smaller than the size of the FIFO, it is copied as many times as possible in the FIFO before the start of the generation. This is done to reduce the risk of errors of bandwidth by transferring is not the new data down to the FIFO fairly quickly. Once started, the generation of the copies of the data are no longer manufactured to fill the buffer. New data can be written in the buffer of PC at any time without interrupting the output.
You can also use the FIFO regeneration. With regeneration of the FIFO, the entire buffer is downloaded on the FIFO and regenerated from there. Once the data is uploaded, new data cannot be written to the FIFO. To use the FIFO regeneration, the whole buffer must fit within the size of the FIFO. The advantage of using the FIFO regeneration is that it requires no communication with memory primary host after the operation started, thus avoiding any problems that arise due to the excessive movement of buses.
Take a look at this link which travels with the regeneration: http://www.ni.com/product-documentation/3874/en/
-
Lack of analog input/output range
Hello!
I LV 8.6 installed on my PC with XP OS and my card is 6024E. I noticed that the analog input/output palette is not appearing or missing. I tried searching but no luck. NOR-Daq traditional 7.4.4 currently installed.
Try reinstalling the device driver CD/DVD and make sure you have selected traditional DAQ.
Say you you installed NOR-DAQ 7.4.4. But if it was made before you install LabVIEW, LabVIEW and then see.
-
OR 9403: Digital Input/Output slows timed loop?
Hi all
I use a loop timed sample of 7 current channels (NI 9023), 3-channel (NI 9025) voltage at 1000 Hz in scan mode and it works fine. However, when I add for 8 output channels of the input/output module digital module NI 9403 for timed loop, CAPAS sampling cannot exceed 1000 Hz. According with time stamp data I wroten in file, it seems that I have in all ten milliseconds, I missed a miliseconds.
I would like to ask is there a reason for this? The digital I/o module affect the timed loop?
Thank you much in advance.
I'm not familiar with the FPGA code, so I can't comment there. However, I noticed that you call writing to text file twice in the timed loop. Can you only collect data and then write the files after the time loop? This would save a lot of time. For each entry, the program needs to access the hard disk, find the end of the file, add him and return to write on the hard drive. A lot of your time, especially since the files are getting bigger.
-
Configuration of the inputs/outputs of NI9401 in labview FPGA
Hello
I am very new to Labview FPGA. In fact, I'm implementing the very first example introduced by OR for learning Labview FPGA. I need to connect an entry of a NI9401 on one exit from the other.
However, when I drag and drop the input/output units, the two act as inputs:
I also changed the propties one of the NI9401 to act as output. But the problem persists.
It is the example that I am building.
I'd appreciate any suggestions.
https://www.YouTube.com/watch?v=mv112V-P030&index=1&list=PLbCk9hRe-ziECXQjE--fN29C_kcx7CHnA
Right-click on the output node, and then select "change to write."
-
Mathematical functions with input/output error
Please refer to the attached picture. Where do you find these mathematical functions with input/output error? I saw these in response to a message.
I think they appear when you connect a waveform or dynamic data type. Since I rarely use these data types (just give the table!), I'm not positive.
Lynn
-
How to start the view off of the ref cursor Oracle as input/output param
Hello world
We use JDev 11.1.2.3 WL 10.3.6 and Java 7.
We are at the beginning of our transition from Oracle Forms to ADF. We have a very large forms that uses many store procedures that have IN/OUT ref Cursor parameters and tables plsql. I tried to find information on best practices to achieve, but only seemed to find tutorials on SEO of the Oracle ref Cursor return functions. I hope we don't have to rewrite our code of database to work with ADF.
This is an example of a proc currently a block on a form based on directly
The ref cursor parameter is input/output to satisfy the way the form handles this type of paradigm.
ADF we want I hope to reuse these procs existing (without the need to wrap/overload them) on the basis of the display objects.
Example:
/ * my record type which houses the information I want to go back * /.
TYPE rec_hist_vacpac_status IS RECORD)
rec_order NUMBER (5),
rec_rownum NUMBER (5),
return_column SAM_VACPAC.vacpac_status%TYPE,
rec_login_id SAM_VACPAC.ins_user%TYPE,
status_date SAM_VACPAC.status_date%TYPE
);
/ * Sets the ref cursor type * /.
TYPE lcur_hist_vacpac_status IS REF CURSOR;
/ * This is a procedure that would take some info link go / return
Return the ref cursor of this information as an in / out * /.
PROCEDURE prc_myinfo_refcur)
pnum_identify_seq_id in NUMBERS
pcur_myinfo IN OUT lcur_hist_vacpac_status);
Can anyone point me in the right direction on documentation on this?
Thank you!
Hi Cemerson:
See this example:
- 1. create a TYPE as an object
CREATE OR REPLACE
TYPE GOTYOB_EQUI
AS AN OBJECT
(
CDELEM VARCHAR2 (50).
TIELEM VARCHAR2 (2)
);
- 2. create a TABLE TYPE AS
CREATE OR REPLACE
TYPE GOTYTA_EQUI
AS THE GOTYOB_EQUI TABLE;
- 3 create a function, it returns the TYPE of the TABLE
FUNCTION fn_equiposarriba)
pa_cdelem IN VARCHAR2,
pa_nucomp in NUMBERS
pa_anperi in NUMBERS
pa_meperi in NUMBERS
)
Gotyta_equi RETURN PIPELINED IS
CURSOR trae_equimani (va_cdelem VARCHAR2) IS
SELECT cdelem, tielem, cdelempadr,
(SELECT cdequi
Of evm_alim
WHERE anperi = eq.anperi
AND meperi = eq.meperi
AND nucomp = eq.nucomp
AND cdalim = eq.cdalim) cdalim
Of evm_equimani eq
WHERE anperi = pa_anperi
AND meperi = pa_meperi
AND nucomp = pa_nucomp
AND cdelem = va_cdelem
AND cdelempadr <> cdelem
AND tielem <> 'A ';
equimani trae_equimani % ROWTYPE;
va_cdalim VARCHAR2 (100);
BEGIN
-Loading los equipos aguas arriba
WHILE equimani.cdelempadr IS NOT NULL LOOP
OPEN trae_equimani (equimani.cdelempadr);
equimani: = NULL;
SEEK trae_equimani INTO equimani;
CLOSE Trae_equimani;
IF equimani.cdelem IS NOT NULL THEN
PIPE ROW (gotyob_equi (equimani.cdelem, equimani.tielem));
END IF;
END LOOP;
RETURN;
END;
- 4 SQL Query with the help of the function... you can use this SQL in a display object
SELECT
*
Of
TABLE (gopq_eventos.fn_equiposarriba (' F-SCZ-043-103', '))
1,
2013,
6
)
)
Best regards, Marcelo
Maybe you are looking for
-
I have a 2015 retina MacBook Pro with an external display k 4 (Asus PB287Q) and since the update for Sierra yesterday, I can select is more scaling "resolutions" which lie between 1920 x 1080 and 3840 x 2160. HD is far too big, far too small 4K. If y
-
How can I return to the home page to access the box
all my files appear highlighted in blue at the top of the screen next in the tab of the box when I open thunderbird Mozilla to recover email rather than the display of the homepage with box sand tab no file titles don't point blue poster culminating
-
Hello.. I've forgotten the answers to my security questions... I do not have the chance to remember the... What can I do now? No idea how delet old questions and put the new ones? PLEASEEE help me
-
I bought an iPhone on eBay, but it has a lock of activation, I have no way to contact the original owner and the seller had no refund on the sale, please tell me I've just wasted hundreds and hundreds of books on an iPhone, I can't use
-
E-mail client Windows downloaded only the elements of the yahoo email inbox
I have configured my client email Yahoo mail with windows account... -The problem is it has downloaded all the emails and now my Inbox in the server is empty... I can shoot back (this is just in case I don't make use of customer mail later I don't wa