Portege 7020 error message: PXE - E01 PCI vendor and device ID do not match

Similar Questions

• I lost the ability to upload files to a Web site. I transfer files from my computer to a web site and I get an error message "the connection was reset" and the file will not download. I try to transfer the photos and I get the same message.

  I have download a scanned receipt on a Web site and I get the error message "the connection was reset". I downloaded these reception for two years and last week, I had to use a different browser to complete this operation. I log onto the site and make the report, I have to do, but I can no longer download on this site.

  Safe mode does not work. However, when I downloaded Firefox laptop everything worked. Any suggestions as to where I should go now. Thanks Fire Fox works on other sites I work with. The download has started working. I think the problem was the website.

• Equium A100-147 with error message "PXE - E61 Media Test Failure"

  Hi all

  I Equium A100 out of warranty due to the error message "PXE-61 Media Test Failure" I took it to my local computer Lamplighter, told me my Toshiba 60 GB hard drive failed (MG6034GSX) and replaced by another 120 GB model.
  I tried to reload the Toshiba Recovery disk system, reload reached 75%, then the messages come in saying that it does not find a lot of operating system files.
  Thinking the recovery disc was faulty, I got a replacement from Toshiba, and this reload disk gave the same problem.
  I loaded XP Professional on the 120 GB HARD drive and it works OK but I'd like to load original as it came with XP MCE.

  Is my problem the 120 GB HDD which should be as original 60 gb and a HDD for Toshiba genuine to accept the recovery media?

  Does anyone have any ideas, I would really appreciate your help.

  See you soon
  diggermender

  Hello

  Don t think that it is a problem of restore CD is normally impossible
  I think that the problem might be related to the HARD drive.

  First of all, you need to access the BIOS and should set the defaults (don't forget to save it).
  Then try to format the whole HARD drive and also remove the created partitions.

  Then you could try again installing the OS from the recovery CD.
  Usually, this procedure works fine

  Good luck

• Firefox 3.5.1 running Vista has stopped working. No error message. Tried to uninstall and install also the latest version and get a message saying that I must first close Firefox (which of course obviously does not work)

  Firefox 3.5.1 running Vista stopped work, no error message. Tried to uninstall and install the updated version. Download the message that I first need to close Firefox, but it is not obviously executed.

  This has happened

  Don't know how many times

  I restored my system to an earlier date, December 2009

  User Agent

  Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; Dealio Toolbar 3.1.1; .NET CLR 3.5.30729; .NET CLR 3.0.30618; NET4.0C; AskTbWCL/5.8.0.12304)

  Firefox can not run visibly, but is probably running in the background. It is in the Task Manager. To access the Task Manager go to Start and type in taskmgrsearch field. This will open the process task manager. Then go to the tab processes and end firefox.exe. After the end of this process, close the Task Manager and try to re-run the installation/uninstallation.

• After you download El Capitan, I received the following error message when you try to install: the drive is not formatted in MAC OS extended (journaled). Use disk utility to enable logging or reformat the disc. Can anyone help?

  After you download El Capitan, I received the following error message when you try to install: the drive is not formatted in MAC OS extended (journaled). Use disk utility to enable logging or reformat the disc. Can anyone help? (My disk utility shows that she in MAC OS extended (journaled) format.)

  It shows that it is Mac OS extended, not journaled. Click enable logging in the toolbar.

  The thing you read is if you format the drive using the RAID settings you have selected. You have to look at the bottom of the window where it shows the Format.

• We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, its error message that gives as no network device connected. Suggest me!

  Original title: problem in installing FSRM

  We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, open the FSRM in "All programs", its error message that gives as no network device connected.  Suggest me!

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 networking forum.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• I can't access to our private internet connection... I get the error messages like acquiring network address AND identity validation

  problem network address acquisition
  I can't access to our private internet connection... I get error messages like acquiring network address AND validation of identity no matter how long I wait nothing happens... Please help me.

  create a new internet connection or reset TCP/IP socket

• My phone displays an error message on the startup file and it mentions the installation media, how can I solve this problem?

  Separated from this thread.

  My phone displays an error message on the startup file and it mentions the installation media, how can I solve this problem?

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  There are several methods to reinstall Vista.

  This can help you (download files and make your own DVDs):

  http://www.heidoc.NET/Joomla/technology-science/Microsoft/57-Windows-Vista-direct-download-links

  And here are instructions on how to burn ISO disk images:

  http://www.SnapFiles.com/get/isorecorder.html

  The download links and information on how to make the ISO file, and then create the Setup DVD above are at this link:

  "How to download a Vista ISO and create a Setup DVD or USB"

  http://www.Vistax64.com/tutorials/301852-Vista-ISO-download-create-installation-DVD-USB.html

  "How to create a USB of Vista Installation key '

  http://www.Vistax64.com/tutorials/181538-USB-bootable-Vista-installation-Flash-thumb-drive.html

  ___________________________________

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  ___________________________________

  And if you have never received a recovery disk when you bought your computer, there should be a recovery on the drive Partition hard reinstall Windows how much you bought your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Them or us ask the right sequence of key.

  ___________________________________

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• I got this error message "winrscmde has stopped working and was closed".

  ERROR WINRSCMDE

  I got this error message "winrscmde has stopped working and was closed".

  Program WINDOWS SECURITY ESSENTIALS download, which found the horse of TROJAN ALUERON in my system. Also, he explains that he keeps duplicating itself and the only way to get rid of it is to download WINDOWS DEFENDER on a CD/DVD or the key to a processor that has the same operating system as the infected CPU offline. I want to know if this Trojan horse attaches to the BIOS? Please tell me the other options...

  Thank you

  Bruce

  Hi Bruce,.
  Your computer is still infected by malicious software. Try the sequence of steps 1 and 2 in this virus/malware removal guide: http://www.selectrealsecurity.com/malware-removal-guide/
  It provides simple instructions on how to remove malware from a computer. If you have any questions, just ask. I hope this helps you.
  Brian

• When I try to delete the message in the "Deleted items" folder I get an error message "some items in the folder"Deleted items"could not be deleted." year error has occurred. Any Suggestions?

  I get to see all the messages that I deleted in my "Deleted items" folder and when I try to delete the message in this folder I get an error message 'some items in the folder "Deleted items" can not be deleted.' an error has occurred.  Also when I try to delete my Inbox it won't move message from 'deleted items '.  Any suggestions?

  This is probably due to a mismatch between what is in the message store and which think that the database is in the message store.  Try to compact and repair the database and see if that fixes the problem.  See www.oehelp.com/WMUtil/

  Steve

• Several installed programs give me error messages that they cannot work properly because I'm not the administrator

  original title: Administrator status

  Several installed programs give me error messages that they cannot work properly because I'm not the administrator.  I double checked with control panel to change my status and I AM ADMINISTRATOR. What is the problem and how to fix this?

  Several installed programs give me error messages that they cannot work properly because I'm not the administrator.  I double checked with control panel to change my status and I AM ADMINISTRATOR. What is the problem and how to fix this?

  Hey Honeybe2

  When you want to use the right click on it and run as administrator

  Walter, the time zone traveller

• "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

  "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

  1. my laptop - acer aspire 5030 - has been having this problem for the last five months.

  2. I tried everything including changing service pack, as we have xp professional, he has recently upgraded to vista business 32-bit with service pack 1.

  3 tried all the methods start the laptop after a few hours, remove the battery, press the power button for half a minute, and so on.

  4. I finally he formatted a couple of times, but the problem is not.

  5. later, I improved the professional system of vista and installed the latest security patches, but the problem remains

  6. now, I started to update its drivers, although the device is identified to be connected, but is not recognized. "the error message" not recognized usb device "appears. I try to reinstall the drivers or upgrade of drivers, it does not. It displays the message "the drivers for this device are to this day.

  7. initially, the connection of the device, the drivers are installed but still the device does not show in Explorer.

  8. I tried to change some registry values by merging a regedit file in the registry - for display devices that are not present; but still, it has failed.

  9. I then tried to delete the file infcache1.inf in c:\windows\system32\inf, but the problem persists.

  10. Subsequently, I tried to create another registry entry to "disable selective suspend" in HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB by adding DWORD and assigning a binary value of 1.

  11. I tried later also to uninstall all the system devices including USB controllers, drives and the storage controllers, who must still without success.

  12. I tried to see if the drivers in safe mode, which they did not.

  13. I tried to delete the following registry entries =

  HKEY_LOCAL_MACHINES\System\CurrentControlSet\Enum | USB PORT; HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10318 & HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10200.  The computer does not have alow it.

  14. the BIOS indicates device pnp "disabled", which I also look for the BIOS settings, which do not allow me to change to change existing ones.

  15. I have not found the WINDOWS\SYSTEM32\drivers\USBSTOR file. SYS in my driver store. This affects the system?

  16. I also contacted manufacturers pnp devices that provided me with most recent and versions compatible drivers for my devices - namely an apple ipod & Seagate external HARD drive - but even after that the drivers are installed properly and the system rebooted the problem remains. Is this something to do with the updated playing driver registry entries does not after the update? OR is what registry entries are configured to only read the entries at the time of the installation of the OS?

  17. I also contacted local sellers who have suggested to me to change the "motherboard". This will help as a last resort?

  18. in the meantime I had also installed other operating systems to Linux - Fedora and Ubuntu; Full Windows XP - Home & Professional and Vista Edition. All these have been installed successfully but do not solve the problem of usb.

  19. I have also raised the original HARD disk & replaced by another HARD disk. also checked the power of all ihee and ehee usb ports to be at least 5 V. I also disabled the automatic deactivation of devices usb by the system. physical contact, ports and connecting cable is fine. the distribution of power is set at 10% for the ihee ports and 20% for ports ehee, which is what is should be the physical output is also close to 5V for all ports connected.

  20. all professional (hardware or software) should any solution for the problem of the usb ports on my laptop?

  Something that you haven't tried:

  How to fix USB device not recognized in Windows

  http://www.online-tech-tips.com/computer-tips/USB-device-not-recognized/

  I hope I could help

• receive an error message that the cover is open, but it is not, on my deskjet 6980. How can I fix it?

  I have a HP Deskjet 6980.  I recently changed the ink cartridge, but since then have not been able to print. I get an error message indicating that "cover is open", but it is not.  How can I fix?

  Hi Cathy,.

  Please follow the t\s mentioned in the following document.

  http://support.HP.com/us-en/document/c01065334

  Thank you

• error message "Windows cannot access the specified device, file, or the path."

  Whenever I try to open a file even my music internet explore or anything that I get an error message Windows cannot access the specified device, path or file.

  Hi nanditaberi,

  Since when are you facing this problem? What were the changes to the system between the time where everything has worked, and when you noticed the problem?

  This problem may be caused by this security software on the computer, uninstall them might solve the problem.

  Example: AVG, Zone Alarm

  Important:

  O before you uninstall the security software disconnect the computer from the internet. Make sure that the windows firewall is enabled.

  Ø you may need to check with the manufacturer of security software for reinstallation and activation.

  O re - install the security software on the computer.

  Reference:

  Please read the steps provided by, Donna, dated Saturday, January 3, 2009 14:01click here for the post.

  A scanner online for any threat and try to correct

  http://OneCare.live.com/site/en-us/Center/cleanup.htm

   

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP photosmart c309a error message States to remove the usb device because it is not compatible

  no previous problems with printing far... error message States to remove the usb device because it is not compatible with the hp photosmart wireless photosmart c309a c309a printer.the only thing plugged into the printer is power cord... no usb device is or was plugged so I do not understand this error message. I unplugged everything and reset the printer but the printer status is offline with the same error message.

  Jorup, try to run this utility and it must diagnose the State of the printer:

  http://goo.GL/u3jDE

  Also, when you unplug the printer, remove the power cord to the back of the unit and the wall for thirty seconds, then reconnect it.

  I would like to know how it goes!