Portege A200 wireless on off does not work

Similar Questions

• Wireless communication switch does not work - Satellite A200 - 23 c

  The laptop has been included, and both a WI - Fi connection stopped working.
  Wireless communication switch does not work. Do not ask is it possible to do?

  Your English confuses me a bit little, but can you please tell me what model of laptop you have and what is the problem here?

  Wireless network card is enabled correctly in Device Manager?

• Wireless network adapter does not work on my Satellite A200

  Hello

  My wireless network adapter does not work under Vista. If I press FN + F8 nothing happens. Wireless communication is always offline.

  What can I do?

  Details:
  Typ: Atheros AR5008X Version: 7.2.0.164
  Laptop Satellite 200
  PSAE6E

  Please help me!
  Thanks in advance!

  Phil

  BIOS bug? I don t think so

  First of all, you must make sure that this isn't a hardware problem. In this case, insert the Toshiba Recovery CD and reinstall the operating system of this device. This will outline the laptop to factory settings. Notes; This would format the whole HARD drive.

  After the new installation, you must activate the WLan switch on the side of books, and you can then use the switch button FN + F8 to select the WiFi network.

  I assume that you have already configured your Wlan router. So the same settings such as the SSID, encryption of WLan, etc. must be defined on the laptop too.

• HP 7612: I have a 7612 Officejet from HP that worked wireless but now does not work. When I try to

  I have a 7612 Officejet from HP that worked wireless but now does not work.  When I try to open the Network Setup Wizard a message indicating "wireless communication has been disabled. Can someone please?

  Thank you!

  hhmenar

  Hey @hlhmenar,

  Welcome to the Forums of HP Support!

  I understand that you are experiencing some problems with the wireless settings is disabled on your Officejet Wide Format e-all-in-one printer. I can help you with that.

  I'll send you some instructions describing how to do a factory reset on your printer. If you check your Inbox of forum you should see happens shortly.

  Please let me know the results after following the above. If you can run the wireless setup, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Update my wireless network device does not work after installation of Software Distribution Service 3.0

  After the installation of Software Distribution Service 3.0 update my wireless network camera does not work how do I uninstall Software Distribution Service 3.0

  How did you receive the update?

  Was it via Windows Update or Microsoft Update?

  Before the changes are made to your computer, the system restore points are made. This is so that you can go back in case an update causes problems.

  Follow these steps:

  1. click on the Start button

  2. click on accessories

  3. click on system tools

  4. click on system restore

  5. click on next

  6. in the calendar that appears, select the one which refers to Software Distribution Service 3.0 and click Next

  After the collection of certain data, the computer will restart, and the update will be gone.

  Hope this helps

  Post back if necessary

  ___________________________________________________________

  If this post can help solve your problem, please click the 'bookmark' or 'Yes' to this message button. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Portege M800 - Exposed sensitive Touchkeys does not work

  I am owner of the Toshiba Portege M800-105. Everything done his work. After 2 months working on it, my sensitive touchkeys exposed next to the POWER button does not work. After that I uninstalled 'Vista-value-added-package' everything works correctly. Why? Now my FN keys do not work or are disabled. Why?
  Before uninstalling the package, the first button next to the power button had to function to turn off the backlight of the Logo, the touchkeys senitive one of my touchpad. NOW he cut the sound! Weired fairy if you aks me. How do I challenge my buttons up to factory settings and make function keys FN?

  I reinstalled the value added package again, and have the backup problem as before: the first two buttons next to the power button does not work!
  Unter the Application: Thoshiba Button supports, for the first two buttons there are no keys depositd/marked so that I can change the configuration here.
  FN keys work after installation of the package, but not the sensitive keys! Please who can help me?

  Value added package has small programs. One of them is the Toshiba button Support. Walker I have uninstall it everything works. When I install it, nothing works.

  Thank you for the help on [email protected]

  Post edited by: Togan_1

  Hello guys

  This is really strange. I put t really know what happen on your laptops. The fact is that these buttons are controlled by the software. If I remember well he called support Button or a button control and she is part of the package of added value.

  VAP contains several different tools and utilities. When you remove the VAP, it will be removed the responsible application of the functionality of FN (Flashcards), and this is the reason why the FN doesn't work anymore.

  So, theoretically everything should be OK when you install PPV again. Again theoretically. Why you still have this problem I put t know and I don t believe that no one can say for sure. Maybe some registry entries are corrupted now? Who knows?

  I presume that you don t want to use a more radical solution and do clean install of the new OS, but it can certainly help. With own OS pre-installed (factory settings) everything works well again.

  In the end, I must say that I use Satellite U400 (similar to your Portege) almost 6 months now and all the buttons work correctly. I always use the Vista version and I n t made no changes. It works well.

• Portege Z30-C-12Z cam does not work with Win 10

  Hello!
  I have a problem with my Portege Z30-C-12Z. Camera in win10 does not work.
  Error code: 0xA00F4273. Have tried all the following steps: http://answers.microsoft.com/en-us/w...0-71c220c123a9 and like many more check the BIOS etc.

  According to me, I tried and everything, checked it please help!

  Try this:
  Type of storage in the search window and go to the storage system settings page. Make sure that the economy sites point to existing folders.
  I moved the files on a SD card and the camera could not find the folder of photos. Also, I've seen the suggestion to check that the folder of photos contains the security settings to allow access.

  If still no good, remove the driver of the webcam from the Control Panel, then let Windows Update to install a driver for the webcam update.

  Reinstall the camera application can also help.

• Portege Z30-A-189: microphone does not work with the connected headphones

  Hello
  I have a Portege z30-a-189 ultrabook.
  Today, I wanted to use Skype with a headset for the first time and I noticed that when the headphones are connected, the internal microphone does not work.
  When I connect headphones that have the microphone, it works, but I want to use headphones that do not have microphone.
  I chcecked all in windows 10 sound settings.

  If you come on a site back, you will find the solution. (see my last post - realtek settings)
  https://Forum.Toshiba.EU/showthread...-in-headphones

• Satellite A200: DVD/CD player does not work

  Excuse me
  I bought toshiba A200.
  After two weeks my DVD/CD drive does not work.
  So I deleted the a±ts driver and then I do not want to install the driver.
  Please help about this.

  Hello

  Don't be angry with me, but your ad is not a little clearer!

  However, the CD/DVD drive uses and supports the common drivers Windows Vista (or XP)!
  You n t need any special drivers to recognize the STRANGE

  In your case I would recommend going to the Device Manager and remove (uninstall) the CD/DVD drive.
  After this procedure, restart the laptop.
  The Vista operating system should recognize the new device and must be reinstalled the drivers automatically

• Satellite A200 - 1 MB microphone does not work on Windows XP

  Hi all.

  I buy a Satellite A200 - 1 MB and when I install Windows XP everything was ok except a little problem:
  The microphone does not work.

  I installed all the drivers correctly, but the problem is the same.
  I read on the internet that many owners A200 - 1 MB have the same problem.

  Is one know how I can fix the problem?
  Thank you

  It's very strange. I installed Windows XP Home SP2 on Satellite U300 edition. It's the same laptop fine but a bit smaller and in my case works cam and microphone. I tested it with Skype. The sound quality is not very good, but it works.

  Are you trying to test also with Skype? Did you check the sound options?

• Satellite L20-264: wireless Internet access does not work

  I have a US Robotics router and a wireless laptop, I followed the instructions exactly in the manual to set up but the internet still does not work wireless but it works through the ethernet connection.

  Can someone help me please.
  If it helps my laptop model is 264 L20
  Thank you

  It is a pity that you describe your problem WLAN so little time and we don t know what you tried exactly and what results are there.

  For properly WLAN use two hardware components must be configured right - the router itself and laptop. It will be interesting to know on what are the instructions you wrote.

  Are you sure that your router is configured correctly?

• Satellite A200-1UQ - battery charger does not work

  Hello

  I myself 1UQ A200 and my battery charger does not work.
  BTW Im from Türkiye.

  Can find the original, if I can't use universal battery charger?

  Thank you

  On the Toshiba site, you can search for a compatible charger and the reference number:
  http://EU.computers.Toshiba-Europe.com-online services & -online Options of PC Accessories devices & -Online Homepage Options & accessories PC

  If you have the part number, you can search with Google for this number. If you can t find something, you need to contact an authorized service provider. They can order all the parts of Toshiba.

  I hope I could help a bit.

• Wireless network card does not work

  Pavilion dv6-6c01eo (A7Q69EA)
  
  Windows 7 64 bit
  
  Network controller is missing
  
  Have formatted the computer with a disc of CD windos 7 64 bit.
  
  Drivers updated via the HP Web site, downloaded all four pilots were of a single function, and it is sp54998.exe [1/1, 5.7 M] works. 3 other updates, sp55714.exe [1/1, 279.13 M] sp55805.exe [1/1, 11.55 M] sp56036.exe [1/1, 10.77 M] does not work. I have internet via an Ethernet cable, but I don't have internet through wireless netverk, it won't work because I have no driver for network controller. I need to download these drivers, where they work.

  Hello:

  Please click on the NIC in Device Manager.

  Then click on the Details tab.

  In the property drop-down list, select the second element (Hardware ID).

  After the first string of characters you see in the window.

  Who will be the ID of the model of the network adapter, and I'll send you the link to the drivers you need.

  HP is not sometimes the drivers for the cards they put in Notepad on the support page and pilot.

  Paul

• Satellite A200-1AX: many applications does not work under Vista

  Greetings,

  I bought A200 1AX a few days ago and I'm not having a good experience with regard to the installation of applications on this Vista box. Even install yahoo messenger did not work and produces the NSIS error. 3D max 9 installation does not work (even though some have managed to operate); Install Adobe CS3 (supposed to be for Vista) did not entirely - the photopshop component have not installed, etc.

  The bottom line, I plan to move to XP OS. Means the required BIOS update I have my Vista recovery CD will NOT work after the switch to XP?

  Thank you for your feedback.

  Best regards, Ashraf.

  Unfortunately I put t know how to help you.
  Usually, if the 3rd party applications are designed and support the Vista while there should be no problem with unique program facilities.

  Check if all software packages are completely cared for and compatible with Vista.

  > The necessary BIOS update means that I have my Vista recovery CD will NOT work after the switch to XP?

  No, after the update the BIOS of XP, you will still be able to use the Vista CD from recovery, but perhaps some functions such as the FN keys will not work.

• Satellite A200-13O - USB port does not work

  Can you help me? I have a new Satellite A200-13O, USB does not work.

  Hi Gilbert

  What do you mean exactly with the USB does not work?
  You plug the 3rd USB external devices advantage, which cannot be recognized?

  Have you installed all necessary drivers for these devices?

  What operating system do you use? If you are using Vista are you sure that the external USB device is compatible and supports the Vista operating system?

  Please post more details!