Portege M100 with client BACK Ghost

Similar Questions

• Portege M100 with PM 1, 2 processors, but the only race on 598 MHz

  Please help, I have 10 pcs M100 and 7 of them have no setting in the Bios to "Dynamic CPU frequency setting" (all the CPU speed, still weak, still strong, dynamic). The laptop which do not have this setting to always operate at 598 MHz I have already check with Sisoft Sandra and in windows system properties. Properties always show that computers laptops Pentium-M 1, 2 GHz 598 MHz. no different between running with the mains or battery adapter.

  Other one with dynamic CPU frequency setting, can dynamically adjust processor clock. They can function normally to 1200 MHz.

  Hello

  The dynamic mode of the CPU frequency is available in Toshiba HWSetup.
  There you can switch between mode dynamically switchable, still high and low fashion.

  Please check!

• No WiFi after installation of XP SP3 on Portege M100

  I have a used protégé M100, on which I recently did a clean install of Windows XP Pro (SP3).
  Unfortunately, as a novice, I didn't save my drivers.

  I've been on the Toshiba site and that you have downloaded everything for this model (M100 protégé Centrino), I printed the "content and the order of installation for windows XP" and load all the drivers at best in the suggested order.

  However, some items were not available to download, or I did not understand the references.

  I downloaded and installed the Atheros client utility and the customer, as well as Configfree utility aironet Cisco, but could find nothing to match the description "wireless driver".

  Perhaps because of this, or not? customer utilities above and ConfigFree (connection doctor) as well as some other diagnostic software downloads tell me I have no installed... wireless LAN hardware but I know it's there, and I never got it out!

  Can someone tell me what I can do?

  Hi George

  I think that you just have not installed the right driver WLan.

  The Portege M100 was certainly equipped with a wireless network card internal minPCI and you should see it in the device under network card Manager. It should appear as an unknown device (if no driver has been installed) or a Wlan-Intel/Atheros/Toshiba/Cisco card.

  Always it is that there are different models of the Portege M100 with different internal minPCI WLan cards and I think you used the incompatible driver.

  Please check the single WLan drivers published on the page of the Toshiba driver and check if you allow your internal wireless network card.

  In addition, you can use the Toshiba WLan portal to get the latest drivers for the Atheros/Intel cards.

  Check this box:
  http://APS.toshiba-tro.de/WLAN/

  Good bye

• Portege M100 - Toshiba utility to install hangs

  I have a Portege M100 (prob M100-112), who has been 'hacked' all by its former owner, and I'm trying to re - install all the tools and drivers.

  In particular, I would like to upgrade the BIOS to v1.50 (1.30).

  The tool to upgrade the BIOS (windows) complains that the common modules are not installed, but when I try to install the common modules Installer crashes just with no visible user interface and no mistake.

  I have re-installed all the points listed in the recommended order - but not luck :-(

  Any help and constructive welcom
  Dave

  Constructive help?
  What else can you get on this forum? ;)

  Hi Dave

  I put t know the order of installation you used and what elements have installed you before, but it turns out that the common modules must be installed first before you start to install the other Toshiba tools and utilities.

  I assume that you try to install Windows XP Home edition, so here's the order of complete plants:

  Driver Chipset
  Display driver
  Audio driver
  Network driver
  Driver Modem
  Network wireless driver
  Atheros Client Utility
  Cisco Aironet Client Utility
  Infrared driver
  Common modules
  Power management
  Button controls
  Console
  Utilities
  ConfigFree
  User manual
  DVD player
  Bluetooth stack
  Utility to change display device
  DVD-RAM driver software
  Mobile extension
  Skins for Windows Media Player
  SD memory card format
  SD Secure Module
  Wireless Hotkey Utility
  Hotkey for display devices
  Sun Java Runtime Environment
  Management Console

  Have you used this order?
  Are you trying to install THIS common modules?

• Screen/hinge Portege M100 problem

  I have a Portege M100 and have a slight problem with the screen
  The screw on the left has out & disappeared. This left the very "wobbly" screen and it seems to have jumped off a plug or two, just on the left side as the case/wallpaper sometimes seems to gape slightly face down by the hinge.
  I would try to replace the screws & it back to the 'normal' but I can't find instructions or advice on how fits in the screen - can someone help me to clip it together & rplace the screw?

  (please don't make comments about how old he was, that's what I have & I can't afford to replace it at the moment!)

  Hello

  I think that there are no manuals or instructions how to replace something on a laptop. These technical documents are not for the public, they available only allowed for the service provider.

  So, I would recommend an ASP because there you can also get the right spare for your laptop and technicians will help you fix it. :)

• Disk error when you exit the Portege M100 in standby mode

  Hello all :)

  Have a Portege M100 for general use with WXP Pro installed.
  Recently decided to upgrade to a DVD - rom DVD burner, then bought a Sony DW-Q250A burner.
  Installed and it worked, but I continue having problems when the computer wakes from sleep, I get the message "ERROR #1 IDE", while the system reboots without additional probs in windows

  The problem is, once this happens, the DVD player then disappears from the window 'my computer' and is not visible in the "Device Manager", until I remove the disc, back up and then analyze for pop. "p in Device Manager devices, it reappears as nothing has happened."
  I thought it might have been a conflict with the IDE bus (ie the two - disk HARD & DVD - disks configured as master) so I put a rider on the HARD disk to make the slave drive (which looks like to mean a change of firmware on the DVD drive for this) but it just created more probs... Then I got a message "ERROR of IDE #0" extra when I did and the machine would not boot from the HARD drive.

  Any thoughts would be welcome? :|

  Mark

  Hi mate,

  "first of all I would like to explain the IDE #0 error: it s quite understandable given that the HARD drive is the * FIRST * player of all and must stand the * FIRST" by car, which means that you jumper shouldn´t to a slave drive. It must be a master, otherwise, as in your case, the boot of won´t machine.
  in
  So you have 2 IDE channels (primary and secondary IDE channel), and each channel has a master and a slave. Apart from the HARD drive that is located on the main channel, your DVD player is naturally on the secondary channel configured as the master drive.
  Here´s a bit 'image': D to explain it:

  -> Primary channel-> Master = HARD drive
  -> Slave = nothing

  -> Secondary channel-> Master = DVD
  -> Slave = nothing

  Regarding your problem:

  I have no definitive solution for you, but I can give you some advice. First download the latest BIOS for your machine and upgrade to the latest version. Then download the latest drivers and install them. After that, look for an update of the firmware of your player of DVD and last but no less check the database of microsoft for known issues as any of the similar issues are known for me with drives toshiba toshiba machines.

  Would be worthy to try

  :)

  See you soon

• Reinstalling OS the Portege 2000 with IDE CD-ROMs

  Hello

  Recently, I got my father a Portege 2000 (purchased at the Japan if it makes a difference) on which I am trying to reinstall Win XP from the provided recovery CD (there are 3 CD containing Windows XP Pro and Win 2000).

  "I'm doing it with a USB FDD and Sony CRX75A CD-Rom PCMCIA that connects to the computer via a different manufacture PC Card ACR - A01 switchable between 16-bit and CardBus mode.)

  As I'm not very familiar with BACK, CardBus and start-up stuff, I read a lot of topics and found the following application, BootdiskP2000.EXE that contains drivers for PCMCIA and USB Toshiba CD-ROM cards. Then I ran and when the choice of CD PCMCIA external drive in the menu, I got the following:

  PC Card driver for external Rev:2203 of the ATAPI-IDE drives
  PCCARD found: IO DATA CBIDE2 V4.1
  ERROR: There is no PCCARD in socket A and B!
  PCCARD not initialized!

  So I searched the web for pilots BACK my ACR - A01 and found DUAOTA16. SYS and DUOATACD. SYS. Then, I changed my CONFIG. SYS (even when perhaps not properly as I'm not comfortable with it) by the addition of a menuitem and further:

  [SONY]
  DEVICE = A:\DUOATA16. SYS
  DEVICE = A:\DUOATACD. SYS D:TOSCD001
  When it works, I get the following:
  DuoATA16 CS Client Driver Version 1.01
  Copyright...
  CBIDE2: Not found CardServices.
  Driver is not installed.
  DuoATACD CD-ROM Driver Version 1.06
  Copyright...
  IDECD: No CBIDE2 card configuration.
  CD drive is not installed.

  If having a glance at HISTORY. TXT file from the startup disk, at the end it says: "If you use it with other CD-ROM, you must modify/change normally the driver CD-ROM (for example Toscdrom.sys - file!). and the driver, on which you have access to the card PCMCIA (Fcatapi.sys and FCPoint.exe). "but I have no idea with what I would have to replace it.

  Last point, my BIOS settings on page 2 are: device Config. = all devices that allows me to set the PC CARD controller Mode = CardBus/16-bit and by the way the CD manufacturing onther used to work fine with the Portege but with a Win XP driver.

  Someone has an idea of what's going on here, because I'm confused. Thank you very much!!!

  PS I also tried to boot using PXE - LAN to a PC running Win Server 2003 but that doesn't work either, but I'm going to start a new topic for it.

  And why Don t you try maybe a USB-DVD-ROM? A USB key will be recognized for sure. I installed a XP Pro with a USB-DVD-ROM on my Portege R200.

  Welcome them

• Wireless card not found - Portege M100

  I hope someone can help me, I'm pulling out my hair!

  I bought a used Portege M100 (model number PPM10E) and is in serious trouble to install the mini-pci wireless adapter that comes with it.

  When I turn on the wireless switch on the front, light on the cover comes in orange.

  Windows XP (Pro, SP1, and SP2 update) does not see the device. Device Manager acknowledges 2 devices with problems: 'Network controller' and 'other devices '.

  I downloaded the drivers all listed for this model and installed (or tried!) in the order specified in the Installation Instructions file (from the same page of drivers Toshiba download for this model).

  I also installed Everest Home Edition, and he sees the wireless adapter and tells me that it is an Intel 2200 BG.

  I tried to get drivers updated Intel and driverguide.com, but none of them will have, either - not even on a clean install, substituting them the driver provided by Toshiba.

  The wireless card works perfectly in other non-Toshiba notebook, also running Win XP Pro - so I guess that there is a conflict of software/hardware with this Toshiba laptop!

  I tried to 'update driver' on 1 2 problem devices) by pointing their (via Device Manager / driver update) each downloaded game (uncompressed) file. No joy.
  (2) to connect to my router via an ethernet cable and allowing Windows to search online for drivers. No joy here no more.

  When I try to run the Atheros Client Utility or Config Free, they can't find any wireless adapter on the system.

  Can someone give me advice on what to do next? Specifically, I bought this machine because I need to use wireless.

  Thanks in advance (and hope!)

  Teddy

  A few questions:
  1. you said that the wireless network card works in the Toshiba laptop not. Did you change the card WiFi of your Toshiba to the other laptop?
  2. you are not sure if it's an Intel or Atheros Wlan card (otherwise it makes no sense to install a client with an Intel Wlan card atheros). Could you please send the PnP ID of the device (DeviceManager-> properties-> details-> Hardware ID)?

• Portege M100 - video player does not work

  Can anyone help?
  Had to rebuild my beloved Portege M100, after a hard disk failure.
  Everything works well except the video player.

  Tried using Windows Media Player and Intervideo Win DVD, but the two close as soon as the video starts.
  WMP has said that this is a problem with a codec called ivivideo forming Intervideo and Corel as they are now.

  However, their site is less useful and I can't find a way to update.

  Suggestions anyone?

  Hello

  Try VLC Player.
  It s small tool/player which can be downloaded for free.
  It plays most files smoothly.

  In addition, you could install some packages of codec as K-Lite codec pack

  Good luck

• Portege M100 - none of the drivers work

  None of the Vista drivers work for Windows 7, so I switched to XP Professional and always SOME drivers don't work?

  Is there a special way to install after installing Windows?

  see you soon

  Hi ollie,.

  It would be interesting to know what you mean with none of the drivers work. You get an error message or what is exactly happening?

  Regarding the issue of Windows 7 I think that it of normal that Vista drivers do not work for Windows 7 because the Portege M100 is very old notebook, so I doubt that Windows 7 will work on this subject.

  Moreover, the Toshiba site, you will find an installation instructions document. Use this list a driver installation order is recommended.
  Check this box!

• Portege M100 - need driver ethernet

  Hello!

  I need driver for my laptop ethernet. It's the Portege M100.
  I have download all the drivers from the drivers download, but still ethernet does not work.

  Thank you!!!

  What you mean with network does not work?
  Brands you yellow in Device Manager?
  Can connect you to a network?
  Please explain this more accurate.

  Did you download the driver here?
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  It would also be interesting what OS you have.

• Portege M100 - no audio output device

  I recently acquired a Portege M100 1.2 ghz model no PPM1DE-0000Y-EN. The hard drive had been cleaned, so I installed Windows XP with Service Pack 3. I don't have a utility Toshiba and driver CD.

  For the moment, my main problem is that there is no sound and I get messages of "no audio output device. I can watch a DVD but once again his silence as the internal speakers do not work. I am a novice, so if you have any tips please try to not do not technical but in simple terms that I can understand. There are probably a number of questions that I haven't discovered yet IE Power Saver, etc. without wire.

  I think you're missing the SOUNDMAX program to render sounds. At least that's what I had with my M200, but apparently M100 and M200 are quite similar. Installed SOUNDMAX SE will solve the problem. The easiest way is probably to get a sort of utility CD.

  And it's probably the only one too. Even if make you it work without, you always end up without the other Toshiba Utilities (which can be quite crucial, as power saving, ability to use the buttons and the FN keys, possibility to use the touchpad, etc..).

• Portege M100 stop when unplug the a/c adapter - battery problem

  Hi people,

  Laptop for my wife, it's a Portege M100 3 or 4 years, which is seems a good machine, although the hard drive failed and had to be replaced recently.
  However, there is also a problem with the battery charging.

  The machine works very well when connected to AC power whether the battery is or not, but as soon as you remove the power cable it stops working immediately, it is to say everything, including the fan stops immediately.

  The sign of the battery on the top edge of the screen/cover blinking orange.
  I figured it was the battery that had given up and bought an another toshiba (IE not a compatible but the real thing) and he slotted in but still.

  This problem above the hard drive has been changed also.

  Any thoughts or ideas?
  Thank you very much

  > The sign of the battery on the top edge of the screen/cover blinking orange
  Are you sure that it is a LED battery?
  AFAIK the battery LED indicates the State of charge of the battery.
  Green: charging completely charged and orange way. But in both cases the LED does not flash/blink.
  Only the power adapter LED will Flash orange if feeding malfunctions and the voltage is abnormal.

  But if the battery LED flashes then I guess this code refers to the battery failure.
  You should always buy a battery recommended by Toshiba and not other 3rd party products.
  The manufacturer of the HARD drive is not important, but if the battery is dead so you can buy one that is part supported by Toshiba

• Several questions on Portege M100

  Hello

  Forgive me in advance if this sounds a bit sketchy but my husband's is the only useful with these things, but his time is limited with work, I thought I'd try and help in advance for when he comes home.

  I bought a M100 to take with us on our vacation, especially to just watch DVDs for children and some web browsing so n t need something fancy or again the guy we got it installed Ubuntu Linux 9.10.

  The main problem we are having is

  1. we can t connect to the internet, the wireless on the top light is still orange (I presume it must be green once everything is well and is connected), even if my husband did the usual things that connected our 3 other laptops for the wireless. It downloaded the user manual and it has to activate the wireless press SHIFT + F8, but this doesn t seem to do anything.

  2. we can play t DVD, the guy we got if says he burned a CD from it, but when we asked to watch DVDs, he said he didn t try know everything, when you insert the DVD, it says you need to download a codex, which her husband is very well done if it was able to connect to the internet.

  I hope all that makes sense please advice on what we could do

  Thank you very much

  Portege M100 is old enough laptop model, and certainly not supported for Linux operating system that's why if you want to use all the functions described in the user manuals, you need to use supported WXP.

  What you need to do is to install the operating system using upgraders original CD.
  Do you have the with your laptop?

  If you don't install WXP using the original disk of Microsoft WXP facilities. All the necessary drivers, tools and utilities that you can download at Toshiba page under http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp for assistance

  If you need good facilities order list please let us know.

• Portege M100 - won't stand by

  I have a Portege M100. No reason he won't standby automatically if left on the battery. I checked settings power saver and they all seem to be ok eg standby after 5 minutes etc.

  Any ideas?

  Hi RogerGrand

  Will your laptop to sleep with connected AC/DC adapter, or it occurs only in sleep mode?
  Moreover, what happens if you choose the mode standby manually via start > stop > Eve. It work?

  In your case, I'll try to reinstall Toshiba Power Saver. You can find it on the page of Toshiba. AFAIK Portege M100 is in * archives * because it s pretty old book.

  Good luck! :)