Portege M700 question cut audio Bluetooth

Similar Questions

• Portege M700: Question on the fingerprint log-in

  Hello

  I have my own Portege M700 today and I decided to perform a clean installation to remove the bloatware.

  Now, I installed an OEM Vista Business 32 bit and I installed all the drivers and software to make it work properly, for all, but a function.

  The connection option.

  How to configure application/toshiba fingerprint utilities into letting me have the option to type my password or drag my finger to log on?

  The default value of the factory were the two options available, but now I'm stuck with only 1 choice, and it bothers me a lot.

  Thanks in advance for your help.

  Hi Tristan

  It would be very interesting to know if you have found the answer to your question.
  Feedback would be appreciated ;)

  See you soon

• Portege M700 Wacom does not respond after hibernation

  I've been using the M700 for two months and I met a very annoying bug. It is not mentioned in this forum so far, but there are other reports on the Internet who mention this problem too. (http://forum.tabletpcreview.com/showthread.php?t=16902)

  * Question: *.

  Tablet is placed in hibernation. When he wakes up, everything seems OK. When you use the stylus or the key functions, that the cursor does not move. Tablet and pen services have not crushed, but there is no link between screen/digitizer and software.

  + Technical support +.
  The series/USB connector is not reset after waking or hibernation is dead the serial connection

  * I tried solutions *.
  So far, I have reinstalled Vista, tried XP (and will stick to it because it's a better OS in many cases) and have reinstalled all kinds of drivers Wacom.

  * What we want *.
  Wacom has also seems to be aware of the problem but says it's a matter of Toshiba. I am impressed with the construction and the quality of the M700 (it is a replacement for my robust but now almost unusable M200 and I have a M400 too, but I never liked it) and this issue is the only glitch I meet.
  I would like to know if anyone else in this forum has experienced a Wacom-coma after the resumption of the hibernation or standby, and if so, if they have found a solution (apart from restarting their PC)

  And I would really like a response from a representative of Toshiba review of this question.

  Hey Buddy

  I m not a M700 owner and, therefore, I can not say much about this issue, but to my knowledge, there are a few different problems with Vista and hibernation mode.
  For example, device high definition audio, screen WLan failed after the resumption of hibernation.
  These issues were definitely Vista problems.

  Installed on Portege M700 Tablet d River was developed by Wacom, I wonder why the guy States that it is a Toshiba issue?  :| (perhaps because this Toshiba laptop s ;)))

  Anyway, you said that you have reinstalled the driver for the tablet of the Toshiba page and updated the Vista of the State. Check the BIOS updated maybe he could improve the functionality

  If this does not work I recommend you contact the ASP to find out if there is a known issue

• Portege M700 - problem with Dynadock

  I can not change the resolution on a screen connected Dynadock and cannot save the display settings of all - how to fix this?

  I have a Portege M700 running Vista Professional SP1 - mainly the machine is used as a desktop replacement, connected to a screen Viewsonic 19 "wide through the Dynadock DVI - when it is connected so I have the laptop screen is off and use only the Viewsonic at a resolution of 1440 x 900. I had been bothered by the fact that whenever the resumption of the screensaver, the resolution would drop down to some lower State (I was not able to identify the dimensions he thought he was using but probably 1280 x 800, the default resolution of the internal display).

  I tried to solve this problem with the technical support level 3 without success. I thought I was smart and try to install the Intel Graphics Media Accelerator Driver update that is located on the Intel Web site (if you're just trying to install this software, Vista won't let you, but if you unzip it and manually update the drivers it works). This resulted in the connected screen Dynadock is off completely - no signal! So I uninstalled the drivers, reinstalled the drivers Intel original, but now, I have no the ability to adjust the resolution on the Dynadock login screen - and it is defaulting to something that's not going to (too broad and not high enough)!

  I lived several cycles to uninstall and reinstall the drivers for the graphics card (Mobile Intel 965 chipset) and the Dynadock; I updated the drivers Dynadock with the latest download from the website of DisplayLink, tried all sorts of drivers for the monitors associated with DisplayLink, tried several restorations system (which have all failed, which was also quite disturbing but less than an immediate concern), etc. Through all this, there is absolutely no way to choose the correct resolution of the screen through the display properties (my choices are 800 x 600, 1024 x 768 and 1280 x 800), and even simply activate an additional screen translates to nothing happens - the new settings do not stay after hitting "Accept" or "OK". I thought that I had licked when I realized that I had to uncheck "Extend to this monitor box office" to screen internal laptop - indeed I was then able to choose 1440 x 900 for the Viewsonic and everything was good, but everything came back after reboot. Of course, now when I try to repeat, I am unable to uncheck this box not more for the internal screen (well, actually, I can uncheck, but when I hit "apply" or "OK" it simply gets selected again).

  All this comes after I spent weeks trying to get this machine to work with the port replicator, which also did not work - a problem that appears to be from an incompatibility with Vista display card drivers and the port replicator (would have been nice if it sales had told me that when I bought the thing, but I digress...)

  In any case, it seems, as it is a Vista problem, I've seen this question asked of other portable devices vista and displaylink other advice, but I know it's possible to have a working reasonably OK solution since I've had one before I went and it messed up trying to work perfectly. Serves me right for spend 3 k $ on a machine and expected that it works as described, I guess. If anyone has any ideas... my next step is probably a downgrade to XP Pro, and then if that does not work, I'm tempted to break into pieces. Or, if someone's figured out how to get the port replicator to work with a M700 Vista, which is actually a better option for me...

  -Tony

  Hello Tony

  It's a very long story, but I use Portege M700 with Dynadock DVI (PA3542Y1PRP) and have no problem at all. After reading your ad I tried changing all the display options and I didn t notice something strange. It works well.

  Read your ad I see you tried to install different things and I wonder not to have so many problems. The best solution for you is to install the new OS using recovery image. Do the clean install of OS and install later Dynadock Utility 2.3 c. be careful while installation is running and do not interrupt the procedure of facilities. Make sure that all software components are installed correctly.

  When you start installation Dynadock Utility Dynacock can not be connected. When you see the window where you will be asked to connect Audio device USB connect the Dynadock to the USB port of your favorite. I use the USB port on the back.

  I use the external display to monitor LCD 22 with a resolution of 1680 x 1050. In the settings screen is display number three and when I click on it I can set the resolution to the maximum level (native resolution). The image is perfect.

  I tried the same as you:
  -Set the external display as primary monitor (for computer laptop LCD was OFF)
  -J' have enabled screen saver and tested several times, but the resolution is always the same no changes at all the
  -With these settings, I rebooted the phone several times as well as the resolution was still the same no problem at all

  After reboot, I can see the image on the notebook LCD only, to the point where I have to write the password that I can see the same image on laptop LCD and external monitor. A few seconds later, the image is switched on external monitor only and it is the same thing you want to have. The resolution is the same again (native resolution). No change at all and all seems OK.

  At the end I've switched back to the LCD display only. It is also interesting to procedure. As a first step, you click on display number one and activate extended desktop. After that, you will be able to use the option to change the primary monitor. A little strange to me, but OK.

  So everything works well for me and for you I only see an option. Reinstall Vista, install new utility Dynadock (new installations) and test again.
  One last thing: do not connect Dynadock on different USB ports. Use always the same.

  Bye and good luck!

• Portege M700 - DVD drive fails during the recording of discs

  Hello

  I tried the Disc Creator that came pre-installed and also Nero 9.2.6.0. All this on Vista 32 bit.

  The latter seems to have no idea about the problem, as it says smething like unknown failure.

  The creator of disc mentions error code 380381-26-BF040304.

  The problem occurs only at the beginning, I tried with three discs, so I don't think that the disks are the problem. In any case, they are DVD + R DL Verbatim and support up to 8 x, while the recorder goes only up to 4 x for the double layer, so I think I'm ok.

  My suspicion is that maybe the firmware in the DVD version needs update... He mentions Hw 1.00, 1.10 Fw. Other manufacturers of laptop as offer updated firmware DVD for her, but I couldn't find one of TOSHIBA.

  Any ideas?

  See you soon

  Hello

  There are several disks for Portege M700, they are compatible. Usually in the user manual, you can find a list of supported CD/DVD players they are pre-tested by Toshiba and work correctly.

  If you have any other questions about a new drive, ask the service provider authorized in your country. They can offer you a compatible player.

• How to connect Portege M700 to TV using the VGA port?

  I bought a VGA S-video/audio adapter and connected my VGA port and the TV.
  Nothing happened.

  In the control panel... no other display/external display was detected.
  Validations only that I ran using an emulator port or something.
  I have the Portege M700 preinstalled with Vista Business lozenges.

  Any ideas would be welcome.
  Thank you

  Hello!

  I have a Portege M700 too and there is no S-video port.

  If you want to switch between the following views the use of FN + F5 as Feliks said. I use the Portege M700 with an external monitor via a VGA cable and it works perfectly.

  Good bye

• Portege M700-130 + Portreplicator + external display

  Hello

  We have a Portege M700-130 with the PA3508E-1PRP portreplicator and have a problem with the external display (monitor) connected to the portreplicator.
  The OS is Vista Business. The external monitor is an EIZO S2401WE-GY.

  Now the question:
  * Can you just place your Portege in the portreplicator, start it with the key to the portreplicator and get an image on the external monitor to the connection of the operating system image without doing anything on your laptop? *
  It would already help us if someone with the Portege even and a portreplicator can give us his experience about it.

  Because we can't, but we have absolut want to achieve or better should. We have tested all the settings in the power and hardware configuration options. The point is: when the Portege gets started without portreplicator and is remplace replaced offshore in the portreplicator, then began with the portreplicator the external monitor goes black when loading of the connection of the operating system image. Only after that the laptop screen is fliped open, we get an image on the external monitor.

  Help or an answer, I'd be very appreciated. Thanks in advance!

  Hello

  One of my friends has tested this on the Portege M700 Vista OS.
  It connected the external monitor using a VGA (analog) and DVI port.

  It seems that it works as you suggest in your ad.
  The Portege lid is closed and connected to the external monitor.
  You do not need to touch the Portege M700. He should start by pressing the key of the duplicator.

  Welcome them

• Re: Inaccurate cursor when using the stylus on Portege M700 Tablet mode

  Hello

  I was struggling with my stylus for a few months. When I use it, the cursor is just the tip, when I'm in the corners (where the calibration takes place). More central that I get on the screen, more it is. We're talking about half a centimeter, which does not seem a lot, but that can be a real pain if you try to write or draw on the screen.
  The tragic part is that it started AFTER I used the tool of calibration for the first time. If I had known that it makes things worse, I would not have touched him.
  My question is: is there anyone out there with the same problem, or is it unique? If this is the case, I'll have a conversation with my dealer after I go home.

  If it is not unique, how this was dealt with?

  My laptop is a Portege M700, with Windows Vista Business SP1. This issue has been consistent through all kinds of situations, hardware configurations and software content, and the starting point was obviously the calibration.
  I thank in advance anyone who can shed some light on this for me.

  Best,
  Oliver

  You're calibrating with the stylus on an angle?

  Try it with the completely vertical stylus.

• Portege M700 - 116 BIOS update error

  HI, I have a Portege M700 - 116 with Vista Ultimate SP1. And I download a BIOS fresh (P005Bv160.exe) [http://ru.computers.toshiba-europe.com/] date of 1, 60 - WIN version 10/10/08. When I try to install it, I get an error window saying:

  Unsupported product type is installed.
  Package BIOS BIOS version: Ver.1.60
  Current BIOS version: Ver.1.50

  So my question is... WHO IS WRONG? What type of product? This update of the BIOS is OS independent and independent language (world-wide), so I think that a lot of people with M700 will have the same problem. There is some problems with the previous version of the BIOS? I downloaded compared to the same month of site there. I do not understand, Setup the BIOS for Windows was made to make the process easy, but it doesn't even...

  Hello

  I see you are using Vista Ultimate.
  I doubt that there is an original version of Vista pre-installed.

  Error message: type of product does not support is installed, said the product (OS software) that is installed is not supported by the BIOS. I think that the error is related to the ultimate Vista preinstalled. Perhaps the BIOS may not be updated under Vista Ultimate.

  It would BE very interesting to know if you can update the BIOS runs Toshiba preinstalled OS.
  Should check this out!

• Portege M700-106: unable to start the task manager & programs after Vista sleep

  Hello

  In fact I am facing problem like below...
  Configuration: Portege M700-106 with upgrades (Hynix Kingston 4 GB, WD Scorpio 320 GB with jumper default config doesn't = no jumper)
  Reinstalled system from Toshiba DVD recovery, all updates possible on web too.

  However, when I wake Vista from the suspense Task Manager I think I can't start (continuous report) some programs (e.g. ThunderbirdPortable of SDHC), all other programs works well enough.

  Anyone can know the reason, solution for this?

  Thanks for help

  Staszek

  Hello

  As far as I understand, you are not able to use some 3rd party applications after the awakening of Eve Vista but other applications running ok only software Thunderbird Portable to the SDHC card.

  Well, I have come to the conclusion that the card reader can hangs after the awakening of the stand by mode or the ThunderbirdPortable should be repeated. Probably it s not a problem of Vista, but question ThunderbirdPortable.
  Have you tried to search if this is a known issue with this software?

  I would recommend this review!

• Problem with webcam not fixed with Vista SP1 on Portege M700

  The Vista SP1 does nothing to the failure of Vista to recognize the built-in webcam Portege M700.
  The existing forum thread mark this question as a response, despite the link to the document toshiba mentioning the error messages entirely different from those cited by those of us with problems

  I find it strange that the M700 UK wouldn't have a built in webcam; is it really true?

  Hello

  I noticed a problem with webcam in time early Vista release, but it was linked to the Vista OS stroller and was solved by SP1.

  Sorry, but another problem with webcam into the unknown for me and as far as I know internal webcam works fine also on Portege M700.

  As you already suggested the internal webcam is not available on all Portégé M700 series. Toshiba notebooks, any series, are equipped with different hardware specifications and example to the webcam internal, in the light of the webcam and internal microphone are available on some models.

  Maybe no problem with a webcam, but some Portégé M700 does not really have an internal webcam ;)

• Portege M700 expansion Bay

  I was wondering, is there Posibility to use the extra HARD disk drive instead of DVD?

  On * European * page, there is no sign of this combination, but on * Canadian * I found something like this...
  [http://www.toshiba.ca/web/product.grp?lg=en§ion=1&group=2&product=4411]
  .. .this option is also on the European page, but without any link with * M700 *.
  [http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/individualOptions.do?service=EU&selCategory=4699&o ldCategory = 4699 & OPTION_ID = 110319 & toshibaShop = false & tab = 2 #2]

  Then maybe someone will know who is right or where to find the answer?
  Correct model in which I am interested is M700-106.

  I could ask the same question about the battery.

  Thanks for help
  Concerning

  Hello

  I think you could do this.
  The Portege M700 is equipped with the Toshiba Ultra Slim Bay. It allows the reader to muliti DVD standard be removed and replaced with the 2nd HDD or a sign of weight gain for increased versatility.

  Good bye

• What is memory max in a Portege M700 - 12l?

  Hello, this may be a stupid question, but... here goes:

  "You can install up to 4 GB of RAM in this Tablet PC. Module of memory up to 2 GB in each of the slots. You must use DDR2 - 667 MHz PC2-5300 modules. »

  But I think there are 4 GB modules, if so, can I use 2 4 GB modules in slots 2 and get 8 GB, it is possible? or this laptop works with the max of 4 GB?

  Thank you.
  PS: maybe this isn't 4 GB and its (2 x 2)...

  If you Portege M700 (PPM70E) then you can increase the RAM to 4 GB only.
  To have 8 GB is not possible because the motherboard can handle with 4 GB of RAM only.

  You can use 2 x 2 GB (PA3513U-1M2G).

  Good bye

• Portege M700 Touch problems

  I recently bought a Portege M700-110 and try to use my finger instead of the pointing device.

  However the calibration of the finger presses a wrong, because when you press the center of the screen is not a problem. But when pushed somewhere to the left or the right unit missed completely the place where I hit and instead, the cursor appears at the edge of the screen.

  I looked the utilities but see a calibration in one.

  Any help would be greatly appreciated.

  Concerning

  Andrew

  Hello Andrew

  Unfortunately, I don't have this model of laptop and cannot give advice but an info is interesting to me. Manual s document of the user according to Portege M700 is delivered with two different screens. One is the screen DIGITIZER model and operations on the screen display can be made using the Tablet PC Pen only.
  The second is the DIGITIZER and TOUCH screen model and on this screen can be done by a finger or pen PC Tablet.

  The question is: can you have? Is it possible to check this? Can you please confirm you DIGITIZER and TOUCH screen?

• Port Replicator/Docking Station for Portege M700

  I'm trying to find a docking station or port replicator port for my portege M700 tablet with no luck so far.

  Ideally, I want something that costs at least 4 ports USB, VGA, audio and LAN.

  Any suggestions please?

  Hello

  You can use the Express Port Replicator Docking Station PA3508E-1PRP part number.
  It should be compatible with your Portege M700

  You know the Dynadock? This pretty s toy and provides different ports.
  For example the Dynadock DVI (PA3542E-2PR) supports video output from DVI port and Dynadock VGA (PA3541E-1PRP) supports the VGA instead of DVI port.

  You can use all these 3 devices with M700

  Check it out