Similar Questions

• Satellite Pro L100 132: old RAM is not recognized by the system

  The original memory of our laptop (Satellite Pro L100-132) is 512 MB.

  I bought an extra memory to 1 GB (type has been verified in the product documentation).
  I installed the additional memory, the system starts and you can see the additional 1 GB memory.

  However, the system does not see the original memory of 512 MB, additional memory is installed on the laptop.

  The system should see memory original and extra, because according to the specification for the serial number of the cell phone (checked on the official website of Toshiba) the maximum memory (which can see the system) is 2 GB.

  I tried to transpose the place of original and additional memory between them, but the problem is the same.
  Updated the system BIOS does not solve the problem at all.

  Hello

  As writes the user above, there seems to be problem of compatibility and updating the BIOS will not help you. A malfunction of the compatibility between the old and new module of RAM which s

  This new module of RAM you bought?

  I think you need two modules of RAM high quality they are compatible together. You can order these ASP RAM modules in your country. Quad has already posted part numbers.

  Check this box!

• 1 t verbatim USB stick not recognized by the system and will not work

  I used my USB from Verbatim 1 t hard drive in the past and it still works on my Vista computer, but know is is a USB 'unrecognized' device and does not work on my XP.  In the system hardware listing is visible, but there is no driver for it and not available from my computer.  This disc is missing?  How can I get this, my backup disk, of the function?

  Hello

  Try the steps of troubleshooting mentioned in the links below and check if the problem persists.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Note:

  BIOS change / additional settings CMOS (semiconductor) to oxide of metal bad cancause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Why my computer does not detect my new USB device when I run Windows XP or Windows Server 2003?

  http://support.Microsoft.com/kb/314634

  Note:

  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756

  How to back up and restore the registry in Windows

• Hardware not recognized by the system

  Hello. I use Windows Professional SP3 and it says its hardware installation and won't let me use the Add Hardware Wizard.  I saw an answer to use Microsoft Fixit, but unfortunately, it says my system is not supported. Is there anything else I can do?

  I have

  Hello. I use Windows Professional SP3 and it says its hardware installation and won't let me use the Add Hardware Wizard.  I saw an answer to use Microsoft Fixit, but unfortunately, it says my system is not supported. Is there anything else I can do?

  I have

  Hi Theross...

  When you get this message? You say what kind of material is it?

  You can use the PC when it starts on the desktop? If you can, do the following:

  Click Start, run and then copy / paste the following command, and then click OK: msinfo32
  (If you have run on the start menu, hit instead of key Windows + R)

  When the menu msinfo32 opens, open the tree in the left menu and then click "problem devices".  Nothing is displayed in the right pane when you do this?

• My Nec DVD RW ND-3520AW drive is not recognized by the system due to the corruption of recording possible

  I have a Gateway desktop and 510 x 86 with Windows XP Home SP3 and Internet Explorer 8.  My system does not recognize my DVD NEC drive due to recording possible file corruption.  How can I clean or set registry entries and/or device driver and get Device Manager to recognize the drive?

  http://support.Microsoft.com/kb/314060

  FixIt have a bad reputation on this forum, so you can go directly to "fix it myself" bit (for XP).

  Let us know how you go.

  Tricky

• NEITHER USB-6501 not recognized by the system

  Hi all

  I wrote this simple application that writes and reads a SPI frame.

  My PC have Labview 8.5.1 and DAQmx 8.7.1 (the CD was provided with my unit NI USB-6501). Everything works fine.

  But now I need to distribute the application, and I need to run it from a computer that does not have LabVIEW.

  I installed the latest versions of the runtime of LV (8.6), and the 8.7.1, DAQmx software but the program crashes produce an error (code 200477).

  I tried to install a more recent DAQmx software (8.9 full, engine of execution of 8,9 only), but the situation has not changed.

  Also: I tried on two different PCs, and I launched MAX: one of them doesn't even recognize that a DAQ hardware is installed (even if Windows recognizes as a work device).

  Anyway, the two PCs return error 200477.

  Any help will be much appreciated.

  Best regards

  Is - this dev4 on the pc without LabVIEW? You can easily see the device name in MAX.

• HP Pavilion Slimline s5212y: my camera to DVD A DH16AAL ATA s5212y Pavilion not recognized in the system after the installation of Windows 10.

  After you have installed the free version of Microsoft Windows 10, I realized that my DVD was neither effective nor recognized in Device Manager. Try as I may to address the support of hp in any problems and try to find updates or fixes to the problem, I have since restored my OS to the older operating system to Windows 7.

  I would like to know if there is a simple patch patch out there in the community that would allow my DVD-ROM to 'see' if I chose to upgrade to Windows 10?

  If there is a "patch" of sorts, I need to have the new operating system installed first?

  Hello:

  The only suggestion I can offer if you haven't tried these, would be to perform the steps listed in each step resolution 3 or 5 from the link below.   Try them both.

  https://support.Microsoft.com/en-us/KB/314060

• Satellite P300 PSPC4E - new battery is not recognized by the operating system

  Hello

  I bought a new battery and it is not recognized by the system
  Satellite p300-PSPC4 win7

  drivers ok
  OK magazine

  The battery is always fully recognized and fully supported. I tried several methods to try to load but nothing happens

  the battery icon is present

  Thank you

  Hello

  Because your old battery is always recognized, I think you bought the battery is not compatible.

  That's why you should buy a compatible battery recommended by Toshiba.
  I think you can buy this Toshiba ASP.

  Welcome them

• Portege R700 Finger Print Reader suddenly not recognized OS

  Hello

  I've been looking for a solution

  My R700 on Win7 worked perfectly using the finger print scanner. At any given time without cause the
  hardware (fingerprint reader to log on) was not recognized by the operating system more.

  -J' tried to remove the software, reinstalled driver
  -updated it and so on resulting material was not found.
  -J' even deleted all the entries in the register - no go.

  -Finger Print genuine software starts, but only to give an error that the FP-reader is not present.

  Is there a way to remove the fingerprint stored manually by removing the manually.

  The equipment works according to the support. (The machine has been send)
  However I don't want to re-setup of the entire machine (it is a work laptop) just to make it work?

  Intro step by step to achieve this or advice?

  I couldn't find a description on how to manually remove fingerprints (cause I suspect this is the problem) from the software to do this does not start.

  Any input would be appreciated.

  Best regards
  Julian

  If you do not see material unresolved fingerprints or devices in Device Manager, then the device is either disabled in the BIOS or the fingerprint sensor is defective or too loose or there is a spill of liquid causing corrosion.

• 6 10 iPhone iOS is not recognized by the laptop Win10Pro

  6 10 iPhone iOS is not recognized by the laptop Win10Pro

  After the upgrade to iOS 10 on my iPhone 6, is is no longer recognized as an external drive by my Win10Pro x 64 laptop on USB 2.0 or 3.0 port. New cable is used to eliminate that as a problem.

  Why is this happening?

  I come to the last iOS 9.x.x?

  Y at - it and the new driver I need to download on my PC?

  I started to automatically backup icloud, but I want to import photos directly to my PC.

  Thank you

  Vicki

  Try opening the iPhone before connecting to Windows. If the film is not empty, then the device should be listed in Windows Explorer. If it still does not show try to restart the computer and the device, and then try again. If it does not show more in iTunes then try iOS device is not showing in iTunes for Windows.

  TT2

• iCloud library is not available if the system library is located on a network file server

  I moved my library on an external hard drive, that drive is directly connected to my router via the USB port.

  I can make pictures to my library of photos and pictures of charge very well. I've set the library to serve the library system:

  

  But, by selecting the option of using iCloud library gives me this error message "iCloud library is not available if the system library is located on a network file server.":

  

  I have the ability to connect this external hard drive to an iMac which is used as a server, I just prefer not, but if it's the only option I want.

  So in short, can I use this configuration? If so, why the error message and how to cope.

  Thanks in advance to all.

  That's right - the library needs (for iCLoud, use of the library and for the safe operation) to be on a local wired connection - may not be on a network connection

  LN

• Sansa e280 not recognized by the pc

  Hi all! I'm new here and I recently had a problem with my sansa 280. I know that for my sansa display in the pc I need to put it on the usb mtp mode. But when I put it on the pc, it does not recognize my computer and he says: "usb malfunctioned or not recognized by the pc. When my sandisk is out of the computer works perfectly. How can I get my computer to recognize the sandisk card? I want to put more music on this subject, and I can't! I use windows vista. Please help me, I would appreciate your help a lot!

  I had your exact the same problem. You can read in the thread I started. I pasted the answer that worked for me here.

  c1u31355

  Download Windows Media Player 10 or 11 from www.microsoft.com and reinstall it. This usually fixes things. Next step, but only if this does not work, is to get the "MTP Porting Kit" from Microsoft and install it.

  Let us know if those who help or not.

• Devices not recognized by the NMP

  I have some SG 300 PoE switches in my network.  In the list of Portal inventory that they show growing to not recognized.  The portal supports devices such as the SG 300?  As it is right now, they are excluded from all the relevant reports (ex: contract management) because of this problem.  An example is the SG300 - 52P which is a 52 GigE PoE managed switch port.

  Hello Christopher,

  You can check if your devices are supported in the current version of the portal by using the checker located here product ID: https://supportforums.cisco.com/document/12098436/sntc-product-id-checker

• DVD player not recognized after the upgrade to windows 8

  I write this to document some odd behavior, that I lived after the upgrade to Windows 8 in the hope that it might save some grief for others.  Of course, if someone could explain why this problem occurs, I'd be very interested/grateful for an answer.

  I recently updated my computer from Vista Ultimate to Windows 8.  I did a clean install of Windows 8, because there is nothing special about the machine I wanted to preserve.  In all cases, the upgrade went without a hitch and I was soon back up with Windows 8 as my OS (I really like, btw).

  The only oddity I noticed after the upgrade is that my DVD drive was not recognized by the operating system.  Remember, this is the same DVD player that was used to install the OS, so I found it rather peculiar.  After a bit of lost time, try software solutions theoretical I started to play with the equipment.

  My motherboard is an ASUS M3A78-EM.  My hard drive is attached to the SATA1 port and my DVD player is plugged into the SATA2 port.  I removed the DVD drive from SATA2, plugged into SATA3, restart Windows 8 (from HDD on SATA1) and Windows 8 now recognizes the drive!

  I thought it was really weird, so I stop, put the DVD on SATA2 drive, rebooted, and the drive was no longer available in Windows 8.

  OK, so I thought that maybe the SATA2 channel was bad (even if he had worked at the Windows 8 DVD installation, just an hour or two before), so I put my HDD on SATA2 and the DVD drive on SATA1.  After doing this, Windows 8 start very well (so there is nothing wrong with SATA2), and it recognizes the DVD on the SATA1 drive.

  OK, so I did that for a while, and virtually all combinations I tried worked as long as the DVD player is not plugged in SATA2.

  I cannot live with that, but thought it was really strange.  Also, I note that the old operating system (Vista) was acknowledging the same DVD player while it was plugged on SATA2.  This leads me to believe that the problem has something to do with Windows 8, but I can't imagine what could be the cause.

  Thanks dude.  After you create this registry key/value and restart Windows 8 was able to finally see my DVD drive on SATA2.  =)

• I found that if it becomes necessary to use time machine to return to an earlier existence to reinstall the iphoto library, if for some reason, you lose lose, then when you try to synchronize your ipad is not recognized by the computer.  As one

  I found that if it becomes necessary to use time machine to return to an earlier existence to reinstall the iphoto library, if for some reason, you lose lose, then when you try to synchronize your ipad is not recognized by the computer.  So when you try to synchronize the pictures, they are all removed from the ipad and trying to reinstall everything again.

  This may or may not work immediately.  In my case, only half the photos have been installed, and then the error message came that the rest of 9000 can be installed.

  I contacted Apple support team who has made various suggestions.  Subsequently clicking on a photo list in iTunes were all going again and pictures of 9000 then installed.  When I asked the support team what could happen I was told that it was a "glitch".  I don't like seeds they mean that there could be an error in coding somewhere.

  Here me again.  I use an iMac and iPad.  I don't know why XP and iPhone came.