Portege Z30-C-10N is unable to boot from PXE - boot MSC mode required

Similar Questions

• Portege Z30-C-10W - not able to boot from USB Windows 7 x 64 SP1

  Hello.

  I'm trying to recreate the image on this laptop via an installer USB that I created that has Windows 7 x 64 Enterprise SP1 on it.

  I was unable to boot from the USB Installer to the station via the F12 Boot menu.
  Setup the USB works on another laptop or PC.
  If I use a WIndows 10 x 64 USB Setup program that starts from the same laptop.

  I tried different options in the Bios, also tried resetting to default values, nothing helps.

  Anyone have any suggestions that I can not have tried?

  Having a similar problem can not get it to boot from a USB key.

• Portege M400: unable to recover from the stand by mode

  My new M400 shot in mode standby on batteries. Then I connect indicator system po DC DC IN is on green. Then, when I press the power button / stop, the indicator of system DC IN yellow flashing and M400 remains dead. It does not respond to any keyboard input and the Dungeon of yellow light on flashing...

  Can anyone help?

  Are you sure that the adapter LED is flashing orange and not battery LED?
  If the battery LED is flashing orange, so this means that the battery charge is lower than battery threshold.

  But if it s a DC in LED, so I guess that there is an error.
  Disconnect the laptop from the AC adapter and try to remove the battery for a period of several.
  After this procedure, put the battery in the laptop and connect the power adapter.
  Try to start the laptop.

• Portege Z30 poster ipv4 and ipv6 - only pxe boot is

  Hi all

  Toshiba Portege Z30

  We do all our installs via PXE, when you press F12 I get now two network options where normally I would just get a.

  F12 gives the following options:

  HDD/SSD: SAMSUNG SSD SERIES
  LAN1: IPv6
  LAN2: IPv4

  When I select the option I get what follows read (IP addresses were not included, but are correctly pointing to the right servers):

  ------------------------------------------------------------------------
  > On IPv4 PXE boot.
  IP address of the station is *. ***. ***. ***
  IP address of the server is *. ***. ***. ***
  NBP filename is SMSBoot\x86\wdsnbp.com
  The NBP file size is 30832 bytes
  Download the NBP...

  Succeed to download the NBP file.

  Download the NBP...

  Succeed to download the NBP file.
  Press a key to continue...
  ------------------------------------------------------------------------

  I tried searching through the BIOS settings but can't find nothing obvious

  Can any advise if there is anything I can try to get this laptop to perform a PXE boot please

  Let me know if you need additional information

  Kind regards
  Steve

  Looks like your server isn't aware UEFI.
  Try changing the the CSM UEFI Boot Mode in the BIOS under the Advanced tab, under System Configuration. You may have to disable Secure Boot first.

• Portege Z30 - I am unable to send SMS

  I have a Portege Z30-A-13F. On the previous Portege, Ericcson device shipped, I used the Toshiba Wireless Manager and the SMS from Toshiba utility in access card for messages (SMS).

  Currently, with the integrated chip of Sierra, I am able to access the network, but there is no interface for SMS on the AirCardWatcher tool.

  The Wireless Manager does not work (I think it only works with Ericsson devices).
  Is it possible to use the SMS with this computer?

  Thank you very much

  AFAIK this is regardless if the laptop supports the Ericson or the Sierra 3 G module.

  The Toshiba Wireless Manager should work fine in two modules.

  Check this document... He explains how to set up and establish a 3G connection via the Manager preinstalled Toshiba wireless.
  http://APS2.toshiba-tro.de/KB0/FAQ1A037W0000R01.htm

• Portege Z30 - A - unable to connect to the GSM mobile network.

  Toshiba Portege Z30 - A Windows 7 Prof

  When I try to connect to a modem GSM receives the error:
  "Network connection based on a mobile broadband connection failed with the error code: 1.

  (GSM card works properly in other devices)

  Hello

  According to the Microsoft Knowledge base, the error code 1 means that the device is not configured correctly.
  One of the reasons why the device isn't configured correctly might be missing a driver or the driver / software are configured incorrectly.

  Recommend you to check the configuration.

• Unable to connect 2 external monitors via the Port Replicator using Portege Z30 - 16U

  Hi all

  I need hell, I just moved from another laptop for Portege Z30 - 16U, I spent hours trying to connect my 2 external monitors to my Replicator Port Hi-Speed III 120W, but my laptop will see a monitor.

  I used 2 external monitors with my laptop for years because I do a lot or reading and I don't want to use the one and the laptop screen.

  I tried the mixture of a VGA and a HDMI and VGA cables, but nothing works.

  Can anyone tell me how I can connect and discover 2 external monitors with this laptop and port replicator, I can't believe that this is not possible, it makes no sense that Toshiba would then technilogically behind other laptop manufacturers.

  Thank you

  Liga

  Hello

  I'm not familiar with the Z30 Portreplicator, but the general behavior of the replicators of the double-displayconnector, is that 1 can be used.
  Not 2 simultaneously.

  I could be wrong, and you should easily be able to check it out - use only 1 at a time.
  First, then the other.
  If the two works when used alone, then my suspicion is right.

  I hope this helps!

  TOm BR

• Portege Z30 PT311E - X 11 crash on Linux Debian Jessie

  I have a Portege Z30 PT311E-01P03GIT

  The laptop works very well in dual boot with Windows 7 and Linux Debian 8.2 (Jessie).
  Under Linux, all hardware is recognized and work, but one notable problem occurs at any time, I try to open a movie from Youtube (or do the equivalent local thing).
  The Xorg server dies, killing all programs and user processes and start the KDM login prompt.

  It connect new, all continue to work until the next Youtube movie embedded in a site or things like that.

  Other than that, all the features and video modes work.
  Any help to solve this problem?

  Thank you

  Below, the initialization of the kernel dmesg messages

  Jan 25 13:39:40 core scree: Console [1.985921]: switch to the color buffer device frame 160 x 64
  Jan 25 13:39:40 Screes kernel: [1.988746] 0000:00:02.0 i915: fb0: inteldrmfb frame buffer device
  Jan 25 13:39:40 Screes kernel: [1.988763] i915 0000:00:02.0: registered declaring panic
  Jan 25 13:39:40 Screes kernel: [2.050218] ACPI: video device [GFX0] (multiple heads: Yes rom: Yes post: no)
  Jan 25 13:39:40 Screes kernel: [2.050388] input: video Bus as/devices/LNXSYSTM:00 / LNXSYBUS:00 / PNP0A08:00 / LNXVIDEO:00/input/input6
  Jan 25 13:39:40 Screes kernel: [2.050445] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0

  Hello

  You can try to disable the frame buffer by adding the following for initialization arguments in GRUB

  fb = false

  Here is a non-Toshiba, not Debian related article describes some useful steps:

  http://KB.Digium.com/articles/FAQ/HO...using-problems

  I hope this helps.

  Tom BR

• Portege Z30 - A - PXE Media test failure, check cable of

  Hello everyone,
  Here's my problem: two days ago my Toshiba Portege Z30 - A turns off suddenly, and when it has reactivated the instead of displaying the usual Windows Home page at he showed a black screen with these lines written:

  'Intel(r) Boot Agent GE v1.5.43
  Copyright (C) Intel Corporation 1997-2013

  PXE - E61: Media test failure, check cable of
  PXE - M0F: Exit Intel Boot Agent.
  Insert system disk in drive.
  Press any key when ready... »

  And every time I turn it on it displays this screen again.
  Why is it like that? What should I do?

  Thank you very much
  Stefano

  It seems that the system does not recognize your ssd more. Usually, the hard/SSD is the first bootdevice and whether it is empty or does not exist, it will jump to usb or networkboot. PXE = networkboot

  Try to start with a live-stick and the check if you can access your SSD. Also see, if the bios/efi does not recognize the drive.

  Worse: all your data is lost... (I hope you have a backup)
  the positive: this question must be covered by the guarantee! If you are still in the first year and registered for the guarantee of reliability, you get your laptop repaired and all your money. xD

• Fingerprints on the Portege Z30-A-12 q utility does not work

  Hello

  I need help with this issue:

  I have installed fresh windows 8.1, the same version as before, but this time I chose UEFI on BIOS. When I used the BIOS the fingerprint sensor was working fine, but now it says "unable to connect to the probe.

  I use Toshiba Portege Z30-A-12 q i5-4200 256 GB SSD, or PT243E model. I've searched the forums and found a similar problem with another Toshiba R product that was resolved by adding an exception to the firewall.

  Utility of fingerprinting with the exception of firewall, even disabled firewall all the way, but always the same problem, I added. In Device Manager, I have biometric sensors (WBF) (PID = 0010) validity under devices.

  I also checked in the BIOS to see if it it turned on and it is.
  The only thing I changed in the BIOS are Secureboot (is on) and has chosen CSM (UEFI), but I think that these settings are not relevant to the problem because they are used for starting.

  I tried to uninstall and reinstall the driver 3 times.

  Please help me with this problem.
  Thank you very much
  Andrei Colombi

  UEFI / start MSC mode has no influence on the fingerprint sensor.

  You said you did a clean install of 8.1 to win.
  I guess that the problem is related to the driver missing or utility.
  I guess you do not have all the essential software available on the Toshiba UE driver page.

  System driver Toshiba to win 8.1 must be installed. It is very important driver package.

  But also try to register fingerprints first in the Windows settings.
  Go to the control panel? Audio equipment &? Biometric devices
  To the left, click Change biometric parameters
  Now, you will see two options: WE (marked) biometrics and biometric OFF (unmarked)
  Now, go to biometric OFF and save changes
  Now go back and click on settings again biometric change
  Now return to the biometrics IT and save the changes.

  Now, you have to click on use your fingerprints with Windows and register fingerprints.

  I think it might be useful to get the utility of fingerprinting works again.

• Portege Z30 - customize touchpad

  I like some Toshiba Z30 touchpad options, like the 2 fingers to scroll, including in web browsers.

  However, I hate the back of the browser (it seems to me that it is controlled by the upper part of the touchpad).

  It always changes accidentally back and forth while browsing Web pages.
  Can I unable that work without disables 2 fingers to scroll?

  If I uncheck 'browser user support functions' in finger scrolling properties then 2 advanced mice also stops working.

  Thank you

  Hello

  It seems that the Portege Z30 would support the Alps Electric touchpad driver.

  As you have probably not known touchpad modules are used in different Toshiba laptops; like touchpad Synaptics, Alps or momentum.

  Mentioned modules are supported on different features so possible that the Alps touchpad would not support the same features of touchpad touchpad Synaptics or momentum module.

  Anyway, the fact is that you can find all the functions of the touchpad supported:

  Control Panel-> mouse-> last tab (device settings)-> the settings button.

  Here, you should be able to get all the touchpad option that could be modified and changed.

• Portege Z30 - A - 18 M - cannot set the native resolution on the external display

  Hello

  I tried to connect two different displays full HD to my Portege Z30 - A - 18 M and I was unable to set the native resolution - maximum resolution I can put for those is 1680 x 1050... I was not so surprised by the first that I had a few problems with a native resolution when I connect to the laptop computer Satellite I had before. But then the same thing happened when I tried the other view.

  I thought that this notebook can handle a higher resolution external... Is there a way to force the native resolution of the external display in Windows 7?
  Thank you!

  Just a question: have you plugged your Portege with HDMI cable and use only the HDMI option?
  With other words went from the desktop to the external display only computer?

  I don't have this machine, but I think you should be able to see the desktop on an external device to the HD full 1920 x 1080 resolution.

• Portege z30-b-14z 10 Pro 64 bit will not be in hibernation

  Dear all,

  My new Portege z30-b-14z 10 Pro 64 bit will not be in hibernation.

  I can not hibernate through the following methods:
  1. click on 'Start', 'power', 'Hibernate '.
  2. press x and windows, click on 'Close or disconnect', click on 'standby '.
  3 a prompt as administrator and type "powercfg/h on" and then press ENTER to activate the Hibernate mode, then type "shutdown/h/t 0".

  Yet once, nothing works. I want to really just close the lid of my laptop and have hibernate.

  Well want to can someone help?

  See you soon,.
  Bender22

  Dear all,

  There has been no response. This is my 2nd Portege for work and I can't go to the Hibernate in Windows or Ubuntu. What gives? I have this job and must close and run meetings with out having to stop and shut down all my programs that I have running. I need this laptop to Hibernate.

  I also have a DynaBook (of Japan) and the R830 running current House to run Win 7 64 - bit professional. They cannot Hibernate or the other.

  Can anyone help, because Toshiba cannot.

  See you soon,.
  Bender22

• Portege Z30 Module problem - A - 13 L 3 G

  I had a problem with a new Portege Z30 - A - 13 L.

  Module 3 G / 4G do not work. As a first step, the Air software map Watcher on the first Installation of Windows 7 detects the sim card and showed a signal, but it Air card Watcher Software still not said no reception (in German: Kein receipt).

  I also put the right apn in the profile.
  I had this problem with 2 different operators sim cards.

  Cause I wanted to use Windows 8.1 anyway I installed it with the original recovery disks.
  The original Windows 8.1 don t comes with Air card Watcher, so you must do with the instruments of the Board of Directors of Windows 8. Windows 8.1, I had a same problem. It detects the SIM, but it says no network (in German: Kein Netz). I put t found the possibility of changing the apn in 8.1 of Windows until you have a mobile connection.

  Initially the Device Manager displays the Module of Sierra Wireless EM 7305 as a network card.
  Then, I uninstalled the driver of Sierra Wireless and installed the Toshiba page.

  After that the Sierra Wireless Module presents itself as a Com device in Device Manager. The cause so much of this networker of Sierra Wireless adapter isn t it, the mobile broadband connection don t even shows charms Windows 8.1 bar upward.

  After that I reinstalled again the image Windows 8.1 with the original recovery disks.
  I saw said that Sierra Wireless Driver has been installed, but the Module EM7305 of Sierra Wireless is presented with an exclamation mark in Device Manager.

  Then I uninstalled and installed the driver manually again.
  He appears again as com device in Device Manager.

  So I think that the module has been a hardware failure. What do you think?

  > After that I reinstalled again the image Windows 8.1 with the original recovery disks.
  > I saw said that Sierra Wireless Driver has been installed, but the Module EM7305 of Sierra Wireless is presented with an exclamation mark in Device Manager.

  On the page of the Toshiba UE driver, you can find and download the [Sierra Wireless Driver LTE 4 G driver | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 362 & selProduct = 17549 & STAS hortMod = null & language = 13 & selOS = 46 & selType = all & year = upload & monthupload = & dayupload = & useDate = null & mode = allMachines & search = & action = search & macId = & country = a he's & selectedLanguage = 13 & type = all & page = 2 & ID = 90092 & OS ID = 46 & driverLanguage = 42]
  This Wireless Broadband Mobile driver is used to transfer data at higher rates and greater capacity.
  Install it!

  Also 3G must be activated before you try to establish a 3 G connection.
  Please check if the 3G module has been activated correctly!

  Recommend checking this information page of Microsoft Mobile Broadband end-to-end
  http://Windows.Microsoft.com/en-us/Windows-8/mobile-broadband-from-start-to-finish

  You will find different troubleshooting tips.

  In the case where you have a signal but you can't connect the possible reasons could be:
  You don t have a valid data subscription.
  The name of the access point (APN), user name or password used for the connection is not valid.
  You're roaming and the selected network operator doesn't allow data services or you don t have roaming enabled for data services.

• Portege Z30 - B - 10 c: is THNSNJ256GMCU SSD supports hardware encryption

  I have a Toshiba Portege Z30 - B - 10 c with 256 GB SSD (exact model THNSNJ256GMCU).
  On the Internet I found weather mixed info, this drive takes in charge or no material encrytpion.

  Could someone help me find the answet to this question and, if it supports encryption.

  How to activate it?

  THNSNJ256GMCU

  Main features
  • Capacities up to 512 GB
  • Available in four Standard form factors
  • MLC NAND Flash memory
  • Low-power Devsleep feature support
  • The end-to-End data protection
  • Gravitational quadruple Code technology (reverse)

  More features
  • Translation mode which allows all disk configurations
  • Hot plug/OS-Aware removal
  Exclusive Toshiba • error correction technology, reverse (Quadruple gravitational Code Technology) support
  • Read only mode supported for emergency

  http://Toshiba.SEMICON-storage.com/e...t-SSD/Hg6.html