Portege Z30 poster ipv4 and ipv6 - only pxe boot is

Similar Questions

• Portege Z30 - A - 1E5 IPS Panel only?

  Hi all

  I wanted to ask if the TOSHIBA Portege Z30 A 1E5 is the only Z30 - A with a slab of IPS?
  Also, is it possible to upgrade a GPS module in a Z30?

  Thank you very much
  MIRU

  Portege Z30 - Models are available on the market. Some models are equipped with a touchscreen and a full HD resolution (1,920 x 1,080) and other models are equipped with a non touch common and HD resolution (1,366 x 768)

  For example the Portege Z30-A-192 supports window color TFT LCD with a resolution of 1366 x 768.

  Portege Z30-A-1E5 was equipped with another fire on the side of color TFT LCD IPS display with a resolution of HF Full 1920 x 1080

• IPv4 and IPv6 are not connected. How / can solve this problem?

  I have a laptop, Wi - Fi and Windows 7. Tried to install the Service pack update and had trouble completing install. Computer Retored previous date, and now I can't connect to the internet. My network is available, but get the error 'conncetivity' and 'limited access' error. When I pull the IPv4 and IPv6 "not connected read properties." Tried to config IP of the term, but nothing comes. I guess that no IP address. Not really sure what to do from here. In addition, something happened to all my previous dates "restore." Only available date is when I tried to install the Service pack.

  Hi JessB,

  1. what version of IE are you using?

  2. What is the full error message?

  Follow the following troubleshooting methods:

  Method 1:

  I suggest you run the network troubleshooter utility and verify the exact cause.

  Check out the following link to run the network troubleshooter utility.

  Using the troubleshooter from network in Windows 7

  Method 2:

  Perform the following steps to enable IPV4/IPV6 addresses.

  Step: 1

  a. open the "Network connections" window, right click to 'connect to the Local network' and click Properties.

  b. Select 'Internet Protocol Version 6 (TCP/IPv6)' and 'Protocol Version 4 (TCP/IPv4) Internet'

  c. click OK.

  Step: 2

  a. click "Start", enter "NCPA. CPL"(without quotes) in the search bar and press"Enter. "

  b. right-click on the network connection, and then click "Properties".

  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  c. click Select 'Protocol Version 6 (TCP/IPv6) Internet' and then click 'properties '.

  d. check "obtain an IP address automatically" and "Obtain DNS server address automatically".

  e. click 'OK '.

  f. click Select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.

  g. check "obtain an IP address automatically" and "Obtain DNS server address automatically".

  h. click on 'OK '.

  Restart the computer.

  I suggest you perform the troubleshooting steps and run the hotfix in the following article to activate IPV6 protocols.

  How to disable or enable certain Internet Protocol version 6 (IPv6) components in Windows Vista, Windows 7 and Windows Server 2008

  Method 3:
  

  I suggest you to rest TCP/IP and check its operation.

  To reset TCP/IP stack to refer to this article and follow the instructions.

  How to reset the Protocol Internet (TCP/IP)

  Method 4:

  Perform the following troubleshooting steps.

  Internet Explorer cannot display this webpage

• A protocol that would provide the service for IPv4 and IPv6 traffic? (RIPv1, RIPv2, RIPng, BGP)

  A protocol that would provide the service for IPv4 and IPv6 traffic?

  • RIPv1
  • RIPv2
  • RIPng
  • BGP

  Hi SandeepTandel,

  ·         Your computer is on a domain network?

  ·         What exactly is the question do you face?

  Here the following protocols provide for IPv4 and IPv6 traffic or respectively:

  Ø Bng supports IPv4 and IPv6 protocols

  Ø RIPng supports IPv6

  Ø RIPv1 and RIPv2 supports IPv4

  Let us know if this information useful.

• IPv4 and IPv6 connectivity says no Internet access

  My computer says that it has access to the internet but when I use a browser it does not work. Also Ipv4 and Ipv6 connectivity says no internet access, and at the launch of the troubleshooting, it indicates that the DNS server is not responding. So there are a lot of problems.

  Hello

  Internet works with IPv4.

  I can't give a targeted response as you have not provided technical information on how you connect to the Internet and devices that are involveved.

  In general.

  Check the Device Manager for the entry of valid card of the wire.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a Local Area Connection icon/entry, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Connect you to the menu of the router from a work computer and make sure DHCP is on, and it is configured to assign IPs which can cover the number of computers that are connected (a bit more will be even better).

  Turn off the computer and the router, reset the router and the computer.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  It still does not work, try this too.

  Firewall software.

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall Windows Firewall should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly, or uninstall it completely allowing the clean flow of traffic on the local network. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Reset the network stacks .

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP, just replace the command typed with.

  netsh int ip reset

  Restart the computer.

  Jack, MVP-Networking. WWW.EZLAN.NET

• IPv4 and IPv6 connectivity

  I have wireless and connected displays IPv4 and IPv6 No. Inernet. Both can I or how can I connect to IPv6

  At this point, you do not have * need * IPV6 and is not something you need to worry. At some point in the future, IPV6 will become a big problem, but most of the devices now are not actively using it.

  I hope this helps.

  Note: If you Google IPV6 you can find a lot of information about this.

• I have a computer that is running windows 7 on our network that there protocols in ipv4 and ipv6 and wont allow me to get rid of one.

  The problem is that they both take an IP is static and a dynamic that is playing with the other computers.Computer performs an IP address and I have someone lose their Internet connection.  Is a static IPv4 and ipv6 is dynamic.

  Thank you

  Ok.. What is
  Start > type cmd into the search bar > right click and select "Run as Administrator" > at the prompt of > ipconfig/release > reboot and see if it's still there.

• What is the difference between ipv4 and ipv6?

  original title: Internet connectivity

  What is the difference between ipv4 and ipv6 connectivity connectivity and which one should I use?

  IPv4 - https://en.wikipedia.org/wiki/IPv4

  IPv6 - https://en.wikipedia.org/wiki/IPv6

  IPv6 deployment - https://en.wikipedia.org/wiki/IPv6_deployment

• Portege Z30-a-1E1 - WIFI connection only 150Mbps

  Hello

  Today, I received my Toshiba Portege z30-a-1e1 running Win7. I've updated all the drivers, firmware and of course Windows itself. Unfortunately the WiFi only connects up to 150 Mbps (router configured to 5 GHz only, 40 MHz wide only, only N and auto channel selection, WPA2 Personal). Other laptops at home are connecting with up to 260Mbps (even 7 Asus F8v). Portrege shows that it is connected with the 802.11n standard.

  Any suggestion that I can do to activate the higher speed connectivity.

  Kind regards
  Blazej

  Hello

  150 megabits per second transfer is not a bad value for 802.11 WLan N standard.
  WLan highest transfer rate depends strongly on factors such antenna Wlan, WLan miniPCI and environment module.

  Wikipedia gives this info on the standard 802.11 N standard:
  … Assuming that the operating parameters equal to an 802.11 network g reach 54 megabits per second (on a single channel of 20 MHz with a single antenna), an 802.11n network can reach 72 megabits per second (on a single 20 MHz with a single channel antenna and ns 400 guard interval); of 802.11n speed can go up to 150 megabits per second, if there are no other shows Bluetooth, oven microwave or WiFi in the area using two channels of 20 MHz 40 MHz mode. If several antennas are used, then 802.11n can go up to 288 megabits per second mode of 20 MHz with four antennas, or 600 megabits per second in mode to 40 MHz with four antennas and 400 ns guard interval...

  http://en.Wikipedia.org/wiki/IEEE_802.11n-2009

  By the way: you can check additional WLan module settings in Device Manager-> properties-> Advanced tab

• Ipv4 and ipv6 on the same ACL line vty

  Hello everyone.

  I just want to confirm if I can protect a router (telnet and ssh) put 2 ACL (an IPv4 and other IPv6) on the same line vty. Something like:

  line vty 0 4 access-class hostsIPv4 in ipv6 access-class hostsIPv6 in

  I have to use named ACL?

  Thanks in advance

  Yes,

  You can do it.

  line vty 0 4

  access-class 60 in

  class to access acl-ipv6-IPv6, in

  transport input telnet ssh

  Kind regards

  Herbert

• IPv4 and ipv6

  tell business-pc Vista is connected-don't support ie7 page-i read somewhere that we can change the ipv6 configuration in the registry so that it uses ipv4 more effectivly

  http://www.mydigitallife.info/2007/09/09/disable-and-turn-off-IPv6-support-in-Vista/

  Read the above.

  See you soon.

  Mick Murphy - Microsoft partner

• How can IPv4 and ipv6 limited connectivity, I connect to the internet.

  I've connected ok then the next day he get limited on ip4 and 6 connectivity, I use a flash stick to write about you that wifi can't connect. I know I, m an area reactive, as there are 12 other sites, but even without password sites give the same message.

  Try to turn off your router, or a wireless connector for a few minutes and then turn it back on.

  Restart your PC.

  Open Internet explore and it will give the option to diagnose the connection problem, run it to detect and solve the problem of connection.

• VMware Guest works with IPv4 and not IPv6 - ideas everything?

  Well, have a little patience with me. I have a very complicated setup which works perfectly with IPv4, but does not work with IPv6. I hope that one of you superstars can help me to understand how to enable IPv6. Here are the basic configuration:

  
  

  Mac mini:
  

  • Mac mini (end 2012) Mavericks 10.9.5 and VMware Fusion 7.1.0 Server
    • A KDLINKS up one1 account USB 3.0 to Gigabit Ethernet adapter is installed. It is functionally identical to all other brands of USB3/Gigabit Ethernet, which is based on the 6 AX88179 chipset adapter; which is the latest version.
    • (I have another identical USB 3.0 to Gigabit Ethernet adapter, still in the box, do not set, in case this might help the solution.)
  • The most recent 6 Mac driver is installed in the Mac mini, downloaded from ASIX. (The driver on the driver of the KDLINKS Web site is a little older).

  Internet connection:

  • Our Internet connection is a regular cable modem. The cable modem is a simple bridge, Ethernet cable. He gets a public (Internet) IP address on the ISP using DHCP Ethernet interface, as you can imagine.

  VMware Fusion Guest - a firewall device:

  • The VMware Fusion guest is a firewall device. Here's its network configuration:
    • The internal interface is bridged to the Mac mini integrated Ethernet adapter. It has a private IP (10-net). It serves as a one-stop shop for all of your home LAN.
    • The external interface is bridged to the USB/Ethernet adapter. The device of host firewalls Gets the address public Internet IP from the ISP via DHCP.

  Mini Mac Network Configuration:

  • Network Configuration Mac mini (OS X System Preferences network 10.9.5,):
    • The Mac mini integrated Ethernet is configured with a fixed IP on the LAN private address and is configured to use the private IP address of the firewall device of comments as the gateway and DNS server.
    • Adapter USB/Ethernet of the Mac mini is defined as:
      • Configure IPv4: Off
      • Advanced... Configure IPv6: Link-local only
      • The goal is to ensure that the Mac mini can be reached or attacked from the Internet. All Internet traffic should be a device of host firewalls.

  Totally works with IPv4.

  Surprisingly, this all works with IPv4 without any problem whatsoever.

  
  

  IPv6 taken in charge by the provider of Internet services and tested with Time Capsule:
  

  There is no problems with IPv6 when I use an Apple Time Capsule as the firewall / router between the home network and the Internet, using the same cable modem. It is easy to configure, and IPv6 works inside the LAN House and all as well go to the servers on the Internet that support IPv6. Tested, working, as expected.

  I'd do it want to use this device to host VMware Fusion as our firewall router firewalls House for IPv4 and IPv6, the time Capsule not.

  THE PROBLEM:

  The device of host firewalls cannot acquire an IPv6 address of the ISP. He obtains an IPv4 address, but not an IPv6 address.

  THE QUESTION:

  What can I do to make the apparatus of host firewalls acquires an address IPv6, the same way as did the Time Capsule?

  • The Mac mini (host) does not expose its interfaces directly to the Internet.
  • The Mac mini (host) would carry its IPv6 Internet traffic via the comments, the same as its IPv4 Internet traffic firewall application.

  Any suggestions would be greatly appreciated.

  I solved my problem. It was a setting of configuration of the firewall of comments and had nothing to do with VMware Fusion. Here are the details, in case others have the same problem:

  Comments firewall device has been configured as a gateway IPv4, but not as an IPv6 gateway. As a result, the firewall received a single IPv6 address of the ISP. It was a 128, of course.

  Once I enabled the 'IPv6 Default Gateway' setting for the interface external unit of firewall of comments (which translates as the USB3/Ethernet interface to the cable modem) and rebooted the modem cable and firewall, the firewall has asked an IPv6 network block instead (a 64 network). After that, everything worked as expected.

  I know that nobody has answered this detailed query, but I know that a lot of people read it. Thanks for taking a peek. I hope this solution helps others.

• can I configure an IPv4 address and IPV6 on the same NETWORK card

  I test double stack IPv4 and IPv6 on a firewall.  Can I configure IPv4 and IPv6 addresses on the same NETWORK card using a laptop installed with Windows 7, in order to test the firewall for both IPv4 and IPv6 protocols access? And if so, how to configure the NETWORK card?

  Thank you

  Jack P.

  See what...

  http://Windows.Microsoft.com/en-us/Windows7/change-TCP-IP-settings

• Portege Z30 - A - 18 M - cannot set the native resolution on the external display

  Hello

  I tried to connect two different displays full HD to my Portege Z30 - A - 18 M and I was unable to set the native resolution - maximum resolution I can put for those is 1680 x 1050... I was not so surprised by the first that I had a few problems with a native resolution when I connect to the laptop computer Satellite I had before. But then the same thing happened when I tried the other view.

  I thought that this notebook can handle a higher resolution external... Is there a way to force the native resolution of the external display in Windows 7?
  Thank you!

  Just a question: have you plugged your Portege with HDMI cable and use only the HDMI option?
  With other words went from the desktop to the external display only computer?

  I don't have this machine, but I think you should be able to see the desktop on an external device to the HD full 1920 x 1080 resolution.