Power connect M8024-K #M8024k #userid #password

Similar Questions

• Satellite A205 freeze after the power connection

  My computer has this strange problem. It stops completely after that I have plug in the power supply.
  What I do now, it is let it recharge when it is off and use it without food.

  There is a chance that it works with the power connected, but generally, it stops again in the trunk.
  If the battery is low and I connect the power usually, it stops right after that I do, sometimes not.

  I also tried to install Linux. But the same thing happens (except by the fact Linux only stops in the trunk)
  I'm now using Windows Vista.

  Thanks for the time and sorry for the English.

  > any suspicion?
  As suggested above; It looks like an electrical problem on the motherboard power supply. Maybe the motherboard must be changed.

• Dell 11 7140 place - do not start after reboot and shutdown without power connected

  Hi all

  I had problems with my new Dell 11 7140 place since I bought it. If I reboot or shutdown the Tablet without the power cable plugged in, it crashes on start/stop to a black looking screen as he stopped (but it isn't). He will sit on this State forever or until the battery is completely discharged. If I press and hold the power button for 5-10 seconds I can force a shutdown and turn off the tablet.

  It's even worse if; After that I have to reboot the machine, it just sits there on the circle of rotation points and never goes anywhere. After a few tries, it will eventually in windows recovery, but he never manages to recover anything. The only way to get the Tablet working again is to reimage the dos operating system.

  I tried the following:

  1. Most recent of the installed BIOS A07
  2. All the latest pages Dell device drivers
  3. The latest version of Windows Update
  4. I tried to start in safe mode, but get points again spinning
  5. Tried to restore points that had once or twice the PC to start again, but the system is messed up. Built in Windows apps like photo viewer don't work anymore and I just to reimage.
  6. Tried running the Dell diagnostics, but which did not find anything wrong

  The funny thing is that if I reboot or shutdown with the power connected, then everything is OK. I can do this all day with no problems. Standby and hibernation work OK with no power attached.

  I have tried everything I can, but I'm at a stage where he's going to have to go back to Dell. Please can anyone give me any suggestions of what I can try, thank you.

  To follow up on this post, the final solution to this issue was to return to the Dell Tablet. The motherboard has been replaced under warranty and since it was returned to me I have had no more problems.

• When I try to update creative cloud, I get a popup to connect, I get my Adobe password, but it does not work. I have reset my password and I tried again, but it still does not work.

  When I try to update creative cloud, I get a popup to connect, I get my Adobe password, but it does not work. I have reset my password and I tried again, but it still does not work.

  The password screen shake when you enter the password?
  If so, it asks your Mac password.

  Don't worry about file opm, Adobe recreates him when you try to connect.

• Unable to connect even after the user password reset

  Hai all,
  
  10.2.0.3 on Linux
  
  Reset a user password and the user is unable to connect as you can see below
  
  
  [oracle@testdb 10.2.0] $ sqlplus sys/Manager as sysdba
  
  SQL * more: release 10.2.0.3.0 - Production on Tue Nov 27 16:20:21 2012
  
  Copyright (c) 1982, 2006, Oracle. All rights reserved.
  
  
  Connected to:
  Oracle Database 10 g Enterprise Edition release 10.2.0.3.0 - Production
  With partitioning, OLAP and Data Mining options
  
  SQL > alter user sysman identified by oracle.
  
  Modified user.
  
  SQL > disconnected from Oracle Database 10 g Enterprise Edition release 10.2.0.3.0 - Production
  With partitioning, OLAP and Data Mining options
  
  [oracle@testdb 10.2.0] $ sqlplus sysman/oracle
  
  SQL * more: release 10.2.0.3.0 - Production on Tue Nov 27 16:20:32 2012
  
  Copyright (c) 1982, 2006, Oracle. All rights reserved.
  
  ERROR:
  ORA-01017: name of user and password invalid. connection refused
  
  
  
  Unable to connect even after the user password reset

  Check
  How to change the password of the database user Sysman (DB control repository schema) [ID 259379.1]
  EMCA 11 g fails with the error "ORA-01017: name of user and password invalid; connection refused"and" username/password invalid name; For DBSNMP or user SYSMAN"[ID 741530.1]

• I can't connect my user name and password are correct, but I can not connect. I have reset my password, but still I can not connect.

  I can't connect my user name and password are correct, but I can not connect. I have reset my password, but still I can not connect.

  You would do this please: 3-bar menu > Options > privacy > history > and make sure that you put to remember history (and certainly not to remember the story never )

• Due to the use of "UserID:password" for PKCS11 when she accepts a PIN?

  Regarding the transparent encryption of data with HSM, I understand that the following command is used to set the master encryption key for the Oracle 11 g database. However, why does must a userID be specified, when the PKCS #11 library requires only a PIN?
  
  ALTER SYSTEM SET ENCRYPTION KEY IDENTIFIED BY 'userID:password '.

  Hello develop,

  We used this as an example; Today, you'll find generally written as:

  SQL > alter the planned system... identified by 'HSM_auth_string '; where "HSM_auth_string" can be "user_name:password", a "PIN" or just a "Password".

  HTH, Peter

• AS5300 connection with any random userid and password

  Hello

  A bit of an odd request, I know, but is it possible to get an AS5300 to enter a user name and password for dial access but to accept random data that are entered in these areas. This should allow any user to connect if they have a valid user name or password.

  I entered in what follows.

  AAA to local USERS & TUNNELS ppp authentication no

  If I use a local user name, it works very well but a random generates the following text.

  Harbour_Ex_as01 #.

  * Jun 16 02:45:39.092 TSB: % ISDN-6-CONNECT: Serial1:30 of the Interface is connected to n/a n/a

  * 02:45:58.661 June 16 TSB: % LINK-3-UPDOWN: Interface Async126, changed State to

  * Jun 16 02:45:58.661 EST: As126 PPP: treatment of connection as a dedicated line

  * Jun 16 02:46:00.429 EST: As126 PAP: I AUTH-REQ id 29 len 30 'richarddfsdfsdf '.

  * Jun 16 02:46:00.429 EST: As126 PAP: authenticate peer richarddfsdfsdf

  * 02:46:00.429 June 16 TSB: AAA: analyze name = Async126 BID type = 10 ATS = 126

  * Jun 16 02:46:00.429 TSB: AAA: name = Async126 flags = 0 x 11 type = 4 shelf = 0 = 0 = 0 = 126 = 0 channel port adapter slot

  * 02:46:00.429 June 16 TSB: AAA: analyze name = Serial1:30 BID type = 13 = - 1 ATS

  * 02:46:00.429 June 16 TSB: AAA: name = Serial1:30 flags = 0 x 51 type = 1 shelf = 0 = 0 = 0 = 1 = 30 channel port adapter slot

  * 02:46:00.429 June 16 TSB: AAA/MEMORY: create_user (0x6242F3E0) user = "richarddfsdfsdf" ruser = "port ="Async126"rem_addr =" async/08453500050 ' authen_type = service PAP = PPP priv = 1 ".

  * Jun 16 02:46:00.429 TSB: AAA/AUTHENTIC/START (116733842): port = list "Async126" = "USERS & TUNNELS" action = LOGIN service = PPP

  * 02:46:00.429 June 16 TSB: AAA/AUTHENTIC/START (116733842): found list USERS & TUNNELS

  * 02:46:00.429 June 16 TSB: AAA/AUTHENTIC/START (116733842): method = LOCAL

  * 02:46:00.429 June 16 TSB: AAA/AUTHENTIC (116733842): status = ERROR

  * 02:46:00.429 June 16 TSB: AAA/AUTHENTIC/START (116733842): method = NONE

  * 02:46:00.433 June 16 TSB: AAA/AUTHENTIC (116733842): status = PASS

  * Jun 16 02:46:00.433 EST: As126 PAP: O AUTH-NAK id 29 len 28 msg is '% authorization has failed."

  * 02:46:00.433 June 16 TSB: AAA/MEMORY: free_user (0x6242F3E0) user = "richarddfsdfsdf" ruser = "port ="Async126"rem_addr =" async/08453500050 ' authen_type = service PAP = PPP priv = 1 ".

  * 02:46:01.197 June 16 TSB: % ISDN-6-DISCONNECT: Interface Serial1:30 disconnected from the unknown, call lasted 22 seconds

  * 02:46:03.677 June 16 TSB: % LINK-5-CHANGED: Interface Async126, changed State to reset

  * 02:46:08.685 June 16 TSB: % LINK-3-UPDOWN: Interface Async126, changed State to down

  Any help much appreciated.

  Thank you

  Richard

  I see at least two ways to allow anyone on the 5300 router any username and/or password.

  The first and easiest is to remove the telephone line ppp authentication command. This will allow anyone to dial on the machine without checking the ID and password. I believe that this will allow them in without the router generates a demand for ID, but that wasn't a big problem because most of the time invites it is generated by the PC before dialing in any case. It may matter is the user using the terminal window after dial where the prompt IS generated by the router.

  The second and more complicated are based on the fact that there are several methods of authentication that can be specified for ppp, including Ganymede +, radius, local and no. You can configure the authentication of ppp with Ganymede + or RADIUS as the main method and 'none' as the backup and run the Ganymede + or RADIUS to a non-existent server. This would cause the 5300 attempt to authenticate on the Ganymede + or RADIUS and when that got no response, he would let the user. I can't guarantee that this would generate a command prompt, but the same remarks apply as in the previous paragraph on why he cannot question.

• Cannot connect to Windows 7, no password prompt on the Welcome screen

  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/no-prompt-box-on-welcome-screen-asking-for/cf1e0543-1547-E011-90B6-1cc1de79d2e2

  Hello I have kinda the same problem as above:
  -> Win 7 Pro
  -> Boots of emissions 'Press ctrl + alt + del' screen
  -> When this is pressed, the prompt for the password is not displayed
  -> Impossible to recover from cd

  After working with this problem for some time, I found that when computer shuts properly, the next log does not display the password prompt.  If the computer is turned off via a second 5 press power button, the password prompt is displayed the next time the computer is turned on.

  I had an old image of the operating system on a hard drive (HD replaced with solid state) that I used to "restore".  The question that has happened again a few days late.  I can't keep backup/restore all the time because it is very tedious (there are a lot of changing data on this computer a duty to back up like that all the time isn't a realistic solution)

  It can be the cause of this problem? I want to solve this problem without having to recreate the image and restore new data. Any help or advice is greatly appreciated.

  Hello

  Were there any recent changes or updates made on the computer?

  Step 1:

  Try restarting your computer in safe mode and check if the problem persists.

  a. restart your computer.

  b. when the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows Advanced Startup Options.

  c. using the arrow keys, select the Safe Mode option.

  d. press the Enter key on your keyboard to start Windows Safe Mode.

  e. when Windows starts, you will be at a typical logon screen. Connect to your computer and Windows goes into safe mode.

  f. check if you still have the problem.

  If it works fine in safe mode try performing a clean boot in order to find the cause root.

  Step 2:

  See the article about how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: when the diagnosis is complete do not forget to reset the computer to a normal startup. Follow step 7 in the above article.

  Method 2:

  I suggest you to activate the administrator build-in account and check.
  a. click Startand type cmd in the Search boxof start.
  b. in the list of search results, right click Guest and then click run as administrator.
  c. When you are prompted by user account control, click continue.
  d. at the command prompt, type net user administrator / Active: Yesand then press ENTER.
  e. type net user administrator , , and then press ENTER.
  Note: Please replace the tag with passwords which you want to set for the administrator account.

  f. type exitand press ENTER.

  g. disconnect from the current user account.

  Let us know if it helps.

• I can not connect. There is no password or e-mail inbox. Nothing

  I can not connect. Just blue screen wth the button to restart or swith to the bottom of my laptop. No password, no e-mail, no photo area. How can I get?

  I think that I disabled it somehow a software which help connect you. Help, please.

  You can use the power button to enter safe mode and restore the last backup checkpoint.  Here's how (see option on this page#1).

• I can not connect. I went to passwords saved and copied but does not work

  I usually just have to click on the Mozilla desktop icon to connect, but today it says connection fails and even if I went to saved passwords they do not seem to work.

  The usual cause is a bad anti virus update, or lack of one in Thunderbird updates.

  1 reset
  2. check that your anti-virus firewall component allows Thunderbird
  3. check with your service provider that their mail server is working.
  4. to diagnose problems with Thunderbird, try one of the following:

  • Restart Thunderbird with disabled modules (Thunderbird Safe Mode). On the Help menu, click "restart with disabled modules. If Thunderbird works as usual, there is an add-on or theme interfere with normal operations. You will need to reactivate the modules one at a time until you locate the offender.
  • Restart the operating system in safe mode with network. This loads only the basics needed to start your computer while allowing Internet access. Click on your operating system for instructions on how to start in safe mode: Windows 8, Windows 7, Windows Vista, Windows XP, OSX

  If the safe mode for the operating system to resolve the problem, there are other software on your computer that is causing problems. The possibilities include but not limited to: AV scanning, virus/malware, background downloads such as updates of the program.

• forget password and I can not connect wifi to reset the password

  Hello

  I forgot my password after changing to connect to my computer and I can't connected to wifi to reset the password

  I need to lose my everything on my Imac with nothing

  What should I do?

  An apple article is here: change or reset the password of a user account from OS X - Apple support

• I have been using Thunderbird now for some time. Just experience issue where it does me not you connect. Using the same password as always. Any suggestions

  Just at random yesterday my email stopped to load new messages. When I hit refresh a screen opens and it asks me to connect with my password. I put my password and it says the password is incorrect.
  My email address is [email protected] suggestions

  Check your password using webmail.

• HP Envy x 360: pin connection goes back to the password

  When I change my login password to pin the next time, I want to connect in it came back to the password.  I changed my PIN several times and works until I have to sign in again.  Your help is greatly appreciated.  Thanks in advance for your expertise.  Also, I hope I chose the right advice to write this query.

  Hey @katydid2,

  Thanks for getting back to me. You may need to delete your current pin configuration and setting back to the top. Open settings, go to Accounts.Locate the pine under Connection Options option and click Setup Remove.Then the PIN again.

  Reboot the laptop and try the new PIN.

  I would like to know how this happens.

  Thank you.

• Satellite Pro M70: Noise with laptop OFF If power connected

  Hello

  I have the following problem with my new Satellite Pro M70.
  A strange volume low hissing sound that happens when the power is connected to the laptop.
  This noise occurs even with the laptop TURNED off when the power is connected.

  This sound can be heard in a noisy room, but is quite annoying when you work in a completely quiet room.

  Anyone else have the same problem?

  Hi Geo

  I presume that this adapter produce this noise. Am I wrong? Can you please locate the source of noise just?