Power failure during the use of Vodafone 3 G card - Equium M50

Similar Questions

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• After the power failure during the restoration of the previous day, cannot enter os or passed the password even in safe mode.

  Have laptop Dell 8100, recently used out of town on a wireless remote, installed updates 47 system.  Upon return home, tried to change cable modem I used before purchasing a desktop computer.  I could not the laptop to work on internet.  So I restored system he choose 2007 too far back, then tried to restore someday, when restoring back to the Sunday I was untangle cords and press the power switch on the surge protector.  Now, I can't even in the system.  Go to the login password that I've ever had, my son has changed in 2002 from Tower to the yankees and protected by to keep his friend out of it, but I've never had to use a password he would always automatically functioning screen icons until yesterday.  The second problem the remote while the screen flashed occasionally and would be less bright black with very low juror I would turn off and cool and could use it later.  It happened when he was 6 months old and they replaced the screen.  In the research I found it eventually the inverter is not the screen and found where to buy however, I can not connect to my system now.  I don't want a new laptop, it has been used very little has everything I need and more photos.  My son who has put a password in 2002 died.  I want to return to my laptop, replace and/or to the inverter.  Need to travel to work.  Unemployed and own building company.  How to remove password?  I've never used a password and don't want everything.  Want to right back to my machine.  When asking my password it says field is no longer round.  Don't know what that means.  I know that he renamed Yankee, I saw that when updating.

  The notion of 'Password' is to prevent any attempt to usurp the security it provides. If there is a quick and easy way to circumvent or to usurp the password protected system, then it would raise the question, what should a password?

  I'm afraid that if you've exhausted all the possibilities and are unable to find/recover your password, you will need to reformat the hard drive and reinstall the operating system.

  The Microsoft policy about lost or forgotten passwords .

• Power failure during the installation of Windows 7

  We had a power failure most when setting up my Windows 7 upgrade installation and it will not complete the installation. I downloaded the iso image and an installation DVD, but it does not start the machine. I checked the DVD works on another box of Windows 7, so I'm stuck. I ran the front compatibility checker I tried to upgrade and we found some good things. Any advice in addition to the upgrade of the mother/processor board?

  Remove the hard drive from the computer, connect it to another format only the Windows partition, reinstall it to the original host and try to re-run the installer of Windows...

• Power failure during the update of firmware for Color LaserJet 2600n

  Just in the middle of the update the firmware for my Color LaserJet 2600n, the power is out. Now I can't get anything to happen on the printer. The screen, or the power lights and the error light, but it does not work when the power is put on. I think that he wiped the previous firmware and either had not started or has been along the way in writing the new info. Is it possible that I can cancel it and reload the original firmware? It hangs on my MacBook Pro running OS 10.6.8. The only thing that the instructions seriously cautioned against a interrupt the installation. Needless to say, this is exactly what happened when the power is out. Any help would be greatly appreciated.

  Randy

  Able to understand me. Has proved to be quite simple. Powered off the printer and turn it back on and represented the firmware upgrade program. The printer didn't restart automatically, so I had to power off and wait 5 seconds before feeding this back. Once he recalibrated itself (which takes several minutes), I was in business.

• Power failure during the upgrade of Windows 10

  Filled with 52% files installation and 15% of the update via WiFi when power failed.  It is is a 64-bit edition Windows Home premium.  Tips on how to continue the research.

  -Can we continue install via Wifi?

  -Can we get installation files and continue on a USB?

  It should be, try to start the computer and see what happens.

  If it goes in a loop:

  Boot from the DVD Windows 10

  How to download official Windows 10 ISO files

  (a) in the screen install now

  (b) click on repair your computer

  (c) click on Advanced Options

  (d) click on troubleshoot

  (e) click on startup repair

  (f) follow the instructions on the screen

  See if that helps

  If this does not work, go DVD 10 Windows, perform a custom installation:

  How to: perform a customized Windows installation

• Agent failure during the ownership change processing

  Hello

  Could someone help me in this issue:

  Data collection is stopped due to the following error:

  15-02-2013 02:08:43.916 ECHO ERROR [IncomingMessage-12294] com.quest.glue.core.jfogbank.JFogbankAgentImpl - an unexpected error has occurred which may cause undesired behavior. You can contact Quest Software customer support if you see this error again: Agent failure during the ownership change processing
  java.io.IOException: no connection is made to com.quest.glue.core.jfogbank.JFogbankAgentImpl@6176959c
  at com.quest.glue.core.jfogbank.JFogbankServer.waitForConnection(JFogbankServer.java:403)
  at com.quest.glue.core.jfogbank.JFogbankAgentImpl.startDataCollection(JFogbankAgentImpl.java:295)
  at com.quest.glue.core.jfogbank.JFogbankAgentImpl.propertiesChanged(JFogbankAgentImpl.java:475)
  to com.quest.glue.core.services.ASPServiceImpl$ ListenerAdapter.propertiesChanged (ASPServiceImpl.java:606)
  to java.util.concurrent.ThreadPoolExecutor$ Worker.runTask (ThreadPoolExecutor.java:886)
  to java.util.concurrent.ThreadPoolExecutor$ Worker.run (ThreadPoolExecutor.java:908)
  at java.lang.Thread.run(Thread.java:662)

  15-02-2013 02:08:43.916 ECHO [IncomingMessage-12294] INFO com.quest.glue.core.services.AgentStatusServiceImpl - failure reported Agent
  15-02-2013 02:08:49.673 ECHO VERBOSE [Windows_System_on_ctsintcovsods3.cts.com AgentStatusService] com.quest.glue.core.agent.AgentInstance - data collection to stop

  What does this error mean?

  Kind regards

  Shiva

  Hey Shiva,

  you are probably using the OS cartridge inherited on x86_64, RHEL or CentOS 6.3 or earlier.

  You must install both 32-bit libraries to do the data collection:

  • -glibc.i686
  • -nss - softokn.i686

  Why is this?

  By dΘfaut x86_64 installation does not seem to install libraries 32 bits, which prevents OSCart commissioning agents.

  Fortunately, OSCart agents are largely independent, and only the C 32-bit kernel libraries (and their dependencies) must be installed in order to get the agents running. Needed to support packages are available on the RedHat 6 32-bit installation DVD in the directory {{packages}}.

  https://support.quest.com/SolutionDetail.aspx?ID=SOL89778

  Best regards, Falco

• Power output during the disk check currently not able to boot to the desktop

  Power output during the disk check.  Now, does nothing.

  I started my system, he said to check the disc. The disk check began, he had run for a while. Then my power is out for a few seconds. Once the power was back on that I tried to reboot and nothing. The monitor shows no info yet. Just black says no signal and turns off. I have no option to boot or anything else besides. What I can do. Thank you

  Hello

  You did it of any material changes or software on the computer before this problem?

  You can connect the monitor to a different display port or connect another monitor if possible and check if it works very well.

  If the monitor is right, it implies that there is a problem with the graphics card or motherboard. In this scenario, I recommend you contact the manufacturer of your computer for help.

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Message "do not power down during the update"control panel screen not fade.

  Product name: HP ENVY 100 e - All - in - One Printer D410a

  Product no.: CN517A

  The message "Do not power down during the update" on the control panel of the printer refused to erase and remained perpetually disaloowing acess the Menu home for other actions as photocopies etc.

  I see.  I found this utility that will help you to solve the problem.  It seems the printer lost connectivity during an update firmware and glitch out.  The utility should take care of it.  Let me know what happens.

• picture password stopped working, says there is a failure during the registration process please try again tried for 2 days

  picture password stopped working, says there is a failure during the registration process please try again tried for 2 days.  He worked for weeks and then stopped.  I tried to change it and get the same message

  Hello

  You can contact Microsoft on phone, please visit the below mentioned link:

  How and when to contact Microsoft and support Customer Service:
  http://support.Microsoft.com/kb/295539
   
   

• Power failure during windows 7 install

  during the installation of windows 7, the power went out.  now all I get is 'the program installation starts services' and then it restarts, again and again.  Help!

  What can I do to pass also to finish installing

  If you started with a fresh install / clean (remove existing partitions of Windows and system) and the installation is always a failure. If this is the case try running Memtest86 +.

  It runs from a floppy disk or CD and should eliminate or confirm if your one or more of your memory stick
  are bad or the values of the SPD in the BIOS are correct.
  Let it run for as long as you can: 2,4,6,8 or several hours (at least 3 full passes), if no error then your RAM is OK.
  http://www.memtest.org/
  Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
  http://www.overclockers.com/forums/showthread.php?t=409152

  J W Stuart: http://www.pagestart.com

• Corrupt VMs after power outage during the moved file

  Hi all, hope someone can help me here. I have a server ESXi 5 run here at home I play with. My Web server and some other vms for development are hosted here. Today, I bought a new hard drive of the server. I have all closed, open the folder, hooked up the reader. Booted back and made the new drive (2 TB), a data store. Then I went into the store of data browser for the old data store and clicked on each VM folder, and click the button "move to". I chose the new data store and copy. Naturally, he said it would take SEVERAL hours. I let it go. Well apparently I doesn't not hang all tight and while doing other work at the office, I struck the loose power and the system went down during the move. When I started back I couldn't use virtual machines. They have all said inaccessible!

  I tried to copy the files to the original location, but then esx complains that the vmdk is not a valid file. Is it possible to retrieve one of these virtual machines, or do I have to discard and start again? Please tell me there is a way to get back!

  I'm afraid there is not much you can do, except a call open with VMware to see if they have a chance or a tool to retrieve the Basic virtual disk file.

  In the log file, there are these two lines:

  2011 10-28 T 04: 01:31.886Z | VMX | DISKLIB-VMFS: VmfsExtentCommonOpen: as much as possible truncation (?) realSize is 1294136, descriptor size 1258291200.
  2011 10-28 T 04: 01:31.887Z | VMX | DISKLIB-VMFS: ' / vmfs/volumes/4e5c1292-e5c44add-2e76-000ffec5d18d/epitomeV/epitomeV-flat.vmdk ': cannot open (the specified file is not a virtual disk): measurement size in the file descriptor larger than actual size. Type 3

  which basically says the vmdk of base/flat has been corrupted. (For size of file in bytes, you must multiply the dimensions indicated with 512)

  Other VMware call, you could create a new virtual disk and restore your last backup data.

  André

• Equium A60 Notebook failure during the update of the BIOS

  Hello
  My computer crashed during the BIOS update recommended to treat the blue screen error message. I have turned it off completely and now it won't start at all. No lights turn on or it's like there is no power getting to the machine. My outlet does work as I have tested. This could mean my battery is dead? I tried to remove and clean the contacts or the update of the BIOS had something to do with it?

  Thank you
  Phil

  Hi, Phil the A60 sometimes fails started well only very rarely that incidentally that happened to me once. To solve this problem requires the removal and re-sitting of the battery pack. However, in your case, it sounds very likely the BIOS update has failed unfortunately is a return trip to Toshiba.

  Richard S.

• ENVY 100 printer D410 - screen says "Do not, power down during the update" permanently.

  I'm a Mac user Mavericks 10.9.1 running on a Mac Book Pro.

  I have a HP ENVY 100 D410 printer that works your for a few years.

  Recently, the LCD screen of the display on the printer offered, "there is a new driver. You want to update? "(Yes/no)

  (Or something close to that.)

  Unfortunately, I chose 'yes '.

  The printer then tried to update, but eventaully the LCD screen on the printer displays a flashing message:

  "Do not feed, down during the update"

  The printer now flashes just this screen continuously. The LCD screen will not display anything other than this message.

  The printer works when connected by cable and wireless. (Airprint works very well).

  I can scan documents, I can print pages, I can even access printers "Web page.

  But the LCD touch screen control panel is 'stuck' in flashing update message.

  I can't find any way to clear this error and allow the printer to complete the update.

  Help. Please, I beg you.

  Hello

  There is a fix to resolve the specific problem, but I'm afraid it is only available for earlier operating systems under OS X 10.5 and 10.6, Windows XP, Vista or 7.

  I you suggest to get a computer with any operating system supported, install the latest version of the software on the HP site using a USB and then follow the steps.

  The latest version of the software can be found below (the basic software should be sufficient):

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&OS=4062&product=4073738&softwareitem=MP-92513-1&sw_lang=&

  Make sure that you carefully go through the procedure to the installation section in the patch download page.

  Hope that helps,

  Shlomi

• Failure during the upgrade to El captain

  Hello

  Trier just to run the El captain of my Mac Book Pro late 2008, 500GB, 4 GB upgrade Yosemity.

  After several attempts, I have to capitulate.

  The Message is that the absence during the installation and the options are retry and save the log file.

  Before the upgrade, it worked very well with all the problems.

  Have been looking for solutions and I do not know if the recovery online could help me!

  I don't have a lot of work put in Photo I am very interested with a recovey that saves my work...

  (Yes, I was to stupid to do a backup before the upgrade)

  Any chance of recovering the contents of my HD

  Allan continues

  This could be a missing file that had not resulted in anything until an update.  I had to save and clean install the operating system. I had a similar problem and take mine to the Apple Store to be fixed, it turns out was a broken HD support, who can apparently cause this problem.  You must back up either with Time Machine or external plug your hard drive to another computer and copy the files you want to save. (TimeCapsule is easier), then take it in to be looked at, they can run Diagnostics on the Apple Store.

  See you soon,.

  Adam