PowerConnect 2748 and aggregation of links 6224

Similar Questions

• MPIO and aggregation of links

  Hi all

  I was wondering if someone could explain the differences between the two briefy, I know that MPIO resides on the layer IP and LAG is at the level of the Mac layer. But I'll put up our Equalogic PS4000XV iSCSI SAN with two hosts ESXi 4 U1. I use VMWares Round Robin MPIO, with the strategy of several VMKernel ports dedicated to multiple NETWORK cards.

  My main question is that I still have to do the aggregation of links? Y at - it an advantage? And if it is how can I go to do it because I have 6 100 ports VLAN dedicated to iSCSI, 4 ports traffic go to the SAN and 2 ports light up to two network cards on the ESX host, when I LAG all the SAN becomes inaccessible. Any thoughts?

  To add, VLAN is not recommended for iSCSI traffic, it is better to use a dedicated switch (preferably a pair of switches).  When a pair is used, there should be a group of ports in the LAG between them (min of 2 Gbps) or stacked.  The configuration of the switch must also be very specific with the PS4000 - flow control enabled on all ports and port deep buffers.

  Download SanHQ from Equallogic.com if you do not already done, this will give an idea of prices of retransmission for your tests under load (with IOMeter for example) - and loads of other cool stuff.  Make sure you have the latest firmware on the PS, including the L1 patch and be aware of vmware PR484220 to do with the MPIO.

  Please give points for any helpful answer.

• Aggregation of links between poerconnect 5324 and poweredge with broadcom adapter

  I am looking for information on how to build an aggregation of links between my powerconnect and three cards broadcom on my server. I want to create a bandwidth of 3 GB.

  I created a team with suite ABEC 3.

  My network have 2 VLANS.

  At this stage, I could ping my server network, and I can ping the server in my network.

  When I defined the three ports of the switch (where three cards are connect) as LASG and I defined in belonging to a VLAN these three ports whose status is F, I ping the server from the network, but I can't ping the server network.

  Could someone tell me how I could build this bandwidth betwween my powerconnect, and poweredge?

  Thanks a lot for your help.

  
  

• Has anyone set up a trunk between switches PowerConnect 2716 and Intellinet 523554?

  I have a client who has three switches Intellinet 523554 in the core switches and various on the edge, including a PowerConnect 2716 switch. The firewall is a Sonicwall, which is plugged into one of the Intellinet switches, and there are three new SonicPoints that plug in the PowerConnect switch. To the best of my knowledge, even if X 0 (LAN) and X 2 (WLAN) are related to the SonicWall, I need to keep these separate networks. If I plug them both in the VLAN 1, network crashes (I presume due to a storm of broadcasting). On all switches, I created 2 VLANS, left 1 VLAN not identified and configured the appropriate access and if necessary junction ports. Two types of switches use the web-based configuration and it is just not a lot of parameters to be set. VLAN 1 traffic goes OK on the trunk, but VLAN 2 does not work. I'm not familiar with the configuration of the Intellinet switches, so I sent an email into their support. Unfortunately, for the chutes, that's what the rest of the world calls aggregation of links, so I have no help from them yet. I am quite confident that the configuration is as good as it can get.

  Has anyone else tried this and been successful? Any thoughts? The PowerConnect switch runs 1.0.1.07 firmware. Thank you

  The marking of VLAN is the feature you're looking for, 802. q. 1, Page 10 of the user guide describes in detail the configuration of VLANS on switches Intellinet.

  Assets.mhint.S3.amazonaws.com/.../523554_manual.pdf

  Page 50 of guide the user to the 2716

  FTP.Dell.com/.../PowerConnect-2716_User%27s%20Guide_en-US.pdf

  Hope this helps

• Does Windows natively support the aggregation of links?

  There are some descriptions on the aggregation of links in Wikipedia.

  http://en.Wikipedia.org/wiki/Link_aggregation

  "Note that Microsoft Windows does support not natively the aggregation of links (at least until Windows Server 2008)."

  I was wondering if this description is accurate? And what about the new windows operating system, such as Windows Server 2012 edition?

  Windows xp, Windows 7 and Windows 8 natively supports the aggregation of links? If the answer if not, anyone know why? I know, Linux and other operating systems support the aggregation of links.

  Hi, Peacegump,

  For NIC teaming or link aggregation support, you will need to contact your provider network adapter or an OEM (for example, Dell offers a driver of consolidation).  They provide you with a driver that allows the grouping of NETWORK adapters, because Windows does not offer this feature in the core of the operating system.

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/thread/f200b747-d9fb-4632-b6a4-aaf89c3dcc9b

  Grouping network adapter and clustered servers

  http://support.Microsoft.com/kb/254101

  How to use matching with Advanced Networking Services (YEARS)?

  http://www.Intel.com/support/network/sb/CS-009747.htm

  Windows 7 - aggregation of links to double bandwidth: 2 p., 2 network cards of each

  http://www.SevenForums.com/network-sharing/124720-link-aggregation-bandwidth-doubling-2pcs-2-NICs-each.html

  If you need more information, transfer your question on the Forum on TechNet.

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads

• Aggregation of links for Equallogic

  A few questions on the Equallogic aggregation and link:

  The physical cable how can I use to set my Berry of EQuallogic iSCSI on my physical switch Cisco 7 K? 2 or 4?

  How aggregation of links can I use: LACP?

  Thank you!

  Hello

  EqualLogic doesn't support grouping/collage/LACP, etc...   You must configure MPIO on the guests instead.

  Kind regards

• LACP SG200 - 08 double speed ethernet when two aggregation of links Mac it

  Hi guys, I use a mac mini and imac with 2 Thunderbolt ethernet adapter to make the aggregation of links on a SG200-08.

  To copy the files of drivers from the mac mini raid0 stroke, the speed of the network can reach 225 MB/S, but the actual speed of the disk drive is only 107 MB/S

  I mean that the two ports in each mac carry only the same data over time. Can he do a given separate two and carry on two ports?

  I can find use VLAN or else combine two IPs for one?

  Don't know how yo SG200-08 GUI web definition (this is my first time using the smart switch)

  Hi Yang, your computer supports a load such as link aggregation/LACP 802.3ad balance method? You can effectively double the data rates without a nic-team aggregation technology or link any.

  -Tom
  Please mark replied messages useful

• SGE2010 stacking compared to the aggregation of links

  Can anyone provide an answer regarding stack switch SGE2010 against the aggregation of links if more than 1 GB connectivity is required between the individual switches? Currently, having multiple switches in a stack configuration but would like to increase the bandwidth between some or all switches. Does support cumulation a link aggregation configuration? If so the ports can be used and how the aggregation of links must be configured in conjunction with stacking?

  Hi Jacqueline,.

  On the SGE2010 - Default stacking ports: 24/GBIC 3, 48/GBIC 4 stacking support, i.e. the two ports.

  If you want a GAP between SGE2010, my suggestion, and others may disagree, would be to stop the default stacking mode and standalone mode.

  Then create a GAP between the SGE2010 switches.

  What about Dave

• aggregation of links in the ucs servers

  Hello. Is it possible to aggregate links in the UCS Manager to get the speed of single link over 10 Gbit/s on each server? How can I do? I can build link interface on linux, which is installed on the server. But what do I do in the UCS Manager?

  Correct, the aggregation of links (port-channel) can be configured between the FI and the IOM if you have second generation FI/IOM and configure the port-channel to the title of the material > material > policies > policies > policy of chassis discovery.

  So pretty much, make you the aggregation of links at the OS level and then proceed to UCS as described above but it will provide a port channel for the entire path (IOM at the END)

  HTH,

  -Kenny

• Check and highlight the links broken and work in numbers

  Hello

  I need a formula that can check a column of links and differentiate the working relationships and broken links.

  For example;

  Delete all the links work and leaving broken links in their cells.

  Thanks in advance

  Hi VossoAllison,

  I need a formula that can check a column of links and differentiate the working relationships and broken links.

  For example;

  Delete all the links work and leaving broken links in their cells.

  How do you identify broken links?

  More information, will lead to a solution.

  According to the response of Barry here URL checker, so broken links produce the text "Error 404" or "error 303", sort the table on that column to raise errors. Select and delete the lines you want.

  Kind regards

  Ian.

  Edited by Yellowbox to correct typos.

• How can I get FF to open a link from FF to the outside, for example from an e-mail, in a NEW TAB and open a link from FF in the SAME TAB

  I want to be able to open links from other applications, such as my email client or the Office Word, Excel, etc., in a NEW TAB in FF v11, AND AT SAME TIME, and by default, be able to open links clicked of in FF (entire page Web or tab) in the SAME TAB AS THE LINK, unless I do a right-click and choose 'Open link in a new tab' or 'Window '. Is this possible? This action/behavior should be an option in the 'options' or settings. If it is already, then it is poorly defined or marked as to what action, it's that the setting doesn't.

  You can set the integer pref browser.link.open_newwindow.override.external '1' on the topic: config page.

  • http://KB.mozillazine.org/about:config

  The pref browser.link.open_newwindow.override.external uses the same values as this pref for calls JavaScript window. Open ().

  • http://KB.mozillazine.org/browser.link.open_newwindow.restriction

• Why control by clicking now launch the link in a new tab (which it is supposed to) and open the link in the current tab as well.

  I've just updated the 13.0.1 and immediately noticed on www.rottentomatoes.com when you hold down the control key and click with the mouse it not only opens a new tab with this link which is what I want. It also opens the link in the tab that I've watched. Now the SHIFT key to launch the link in a new session did the same thing. Launches the new session and opens the link in the existing session.

  I'm looking at this particular site:
  http://www.rottentomatoes.com/top/bestofrt/?year=2011

  Excessive use of unnecessary spaces is there in the code of the page.

  It happens in Firefox 3.6.x and Google Chrome as well.

• Starkey Halo 2, 6s and Honda Handsfree link iPhone?

  I am a new user of Starkey Halo 2 i2400s (like them!) with iOS 9.3.1.  I had a problem with the link file between the HAs and the phone.  When it falls, I can't get alerts in my AP or disseminate content to the HAs, and audio phone won't the HAs, although iOS chose "Of Sam hearing aids" as the audio routing.  I'm not new to the joys of Bluetooth technology and have really rubbed my BT environment, eliminating any BT connection (farewell keyboard, etc.).  Now the BT link between phone and HAs standing and TruLink works (especially).

  But when I get in my car, the HA link <>phone is lost.  The 2011 Honda agreement has Link handsfree BT and had been linked to my phone.  I deleted this profile of BT and each profile that knew the car, so the phone is not pairing with handsfree Link, but it still breaks the link HA <>phone.  When that happens, I can't find any way to restore the link without saying iOS to forget devices, restarting the HAs and rematching.

  Does this sound familiar?

  Thank you!

  Hello samuel_wilson,

  Thank you for using communities of Apple Support.

  If I understand your message every time that you are in your car you already linked to your iPhone via bluetooth, it is then disconnect your hearing device.  I suggest that you reset the network settings on your iPhone in order to get this matter resolved.

  Reset the iPhone. Go to settings > general > reset, and then choose an option:

  • Reset network settings: When you reset the network settings, the previously used networks and VPN settings that have not been installed with a configuration profile are deleted. (To remove the VPN settings installed by a configuration profile, go to settings > general > profile, select the profile, and then tap on delete.) This removes also other parameters or the accounts provided by the profile). Wi - Fi is turned off and then on again, disconnect from any network you're on. The Wi - Fi settings and "Ask to join networks" are lit.

  Reset iPhone

  Take care.

• Phone numbers contained in the e-mails and the web links will appear for several seconds and then disappear. I use Yahoo mail, however, if I use IE 8, the problem does not occur. Help!

  Phone numbers contained in the e-mails and the web links will appear for a few seconds and then disappear. I use Yahoo mail, however, if I use IE 8, with Yahoo mail, the problem does not occur. Help!

  This has happened

  Each time Firefox opened

  Is whenever I use Firefox

  Tools > Addons > > Extensions

  You have the Skype for Firefox extension?
  If so, disable it. Known to cause this problem for many users.

• Just bought a Panasonic Viera TV and seeks to link to my mac.  The operating instructions do not help.  Any thoughts welcome

  Just bought a Panasonic Viera TV and seeks to link to my mac. The operating instructions do not help. Any thoughts welcome

  You have two ports thunderbolt on the end 2013 iMac, but not HDMI port. You will need a mini DisplayPort to HDMI adapterand a length of cable HDMI to your TV. If this TV is a model of 4K, then she might want more recent HDMI 4 K wiring (1. 4 (b) specification. You may be able to pick up this adapter to a local Apple or computer store.

  I have a length of HDMI cable connected to my TV (not a Panasonic) with the mini adapter DisplayPort to HDMI adapter connected to it. I turn on the TV and changing to that HDMI port, then turn on the Mac. My Mac screen is duplicated on television. According to what default settings are configured in your TV, you may need to modify the program to look a HDMI (normal, cinema, big screen, etc.) to taste. Start with the default setting.