PowerConnect 5548 sending frames unmarked to Sonicwall

Similar Questions

• HDMI piling on PowerConnect 5548

  We have 8 switches PowerConnect 5548 and are interested in using the stacking of HDMI for 10GbE.

  We currently have all 8 switches under tension and production running on them traffic.  Each switch is currently either back 'a home run' to a Cisco switch, or connected to another switch PowerConnect 5548.

  • Is mature enough stacking HDMI technology for a production environment?
  • It would be important if each switch have been 'home run'd ' to the Cisco switch and each 5548 PowerConnect was connected in a loop HDMI?
  • Stacking HDMI technology would require restart us our switches to implement?  A failure would be necessary?
  • All the special items of note regarding the type of HDMI cable?  (i.e. owner or any which best buy HDMI cable work?)

  Thank you
  Jon

  Is HDMI sufficiently stable stacking of the PowerConnect 5548 for production?

  • Yes (100%)
    
  • None (0%)
    
  • A little, but you better pay attention to the comments I post... (0 %)
    

  • Total votes: 5

  Jon,

  Technology HDMI wroks ideal for stacking the PowerConnect 55xx series. You can use the HDMI ports on the 55xx for stacking well and not for uplink to a Cisco or other device.  Also, you can stack only as 55xx switches with other 55xx and running the same version of the firmware.

  On the 55xx, you don't need to reboot the switches, but just plug the cables to create the stack.  An algorithm is used to determine which members becomes master and members who become slaves.  In my view, that the master is determined by which switch has been powered as long.  Don't forget that if you have the switches on different subnets or VLANs, they are configurations will be now changed all switches will become like a big switch.

  The type of HDMI cable is important, you will need to consult the documentation that came with the switch, or you can download the Guide of the user to http://support.dell.com.  You need cables that provide a flow rate of 10.2 Gbps (maximum allowed by the HDMI specification).  Usually the cheapest cables don't provide this.

  -Victor

• Need help to buy PowerConnect 5548 or 6248

  I currently Powerconnect 6248 and 6224 switches via my network.  On a floor 48 port switch is full and I need to add another, my thought is to add an another 6248 and stack them, but told me that I should get the 5548 and use sfp + 10 gig connection to connect to my 6248.  When I talked to my rep at Dell, he said he would not recommend it, but it might be possible.  Can someone tell me what would make the most sense?  Currently, we have data on the site servers and applications but will move them to a data center in the near future.

  The first thing that comes to mind would be to run as two stacked 6200 switches. When stacked it management makes it a little easier since the stacked switches act as one. It also less time spent on configuration with the addition of a member of the battery compared to a separate switch. Once 6200 switches are stacked you would also have the ability to Setup redundant connections by implementing a SHIFT that uses a port to each of the switches.

  On the other side of things, I'm not familiar with the topology of your network. So there may be a specific situation that is the reasoning behind this recommendation of people. They gave no explanation of why they would recommend the 5548 with connection sfp + on the stack?

  Thank you

• How to send frames to header + 1 byte of data in network LIN?

  Hello

  I use USB-8476 to communicate to a slave in a LIN network. Can someone tell me how I can send a header file more 1 byte of data to the slave in a LIN network.

  I need to send a sync + id 00 X 34 break, followed by a byte of data. I don't know how a master can send this extra 1 byte of data. I need to send this command to the LED and byte 1 to control the level of illumination of the LED lights.

  If anyone has examples for this, can share you here?

  Thank you

  Hi Andreas,

  This error has not yet been documented, but I got the information on the other forums.

  Error name error Code (hex) description

  Task-master of 1040 LinBusErrorTxSyncTimeout LIN interface is trying to send a

  synchronize the bytes and not not not receive the sync byte

  during the period.

  This is the description. The problem is solved, the baud rate I gave was higher than the speed of the slave units. Now, it seems to work correctly.

  Thank you.

• Creation of the VLAN between Powerconnect 5548 and F10 s4810...

  In the coming months we will replace our network equipment.  I was able to get their hands on the new gear at the beginning, and if I'm not traditionally a guy from the network, the project has been given to me and I started playing.  The first thing that I wanted to work on was implemented VLANs.  I have configured the switches like the picture below:

  

  When I have IP every PC connected to the same subnet and apply VLAN10 to their respective ports, they aren't to pings within the same stack or between cells.  My basic understanding is that they are, do they not?  Did I miss something in my understanding of VLANS or is there a problem with my configs?  I posted the configs below.

  RTTMOACCESS01 config:

  database of VLAN
  VLAN 10,20,30,40,50
  output
  Add a voice vlan Yes-table Nortel___ 000181
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table Shoretel___ 001049
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  860 port address 0.0.0.0 iSCSI target
  port 3260 address 0.0.0.0 iSCSI target
  port 9876 address 0.0.0.0 iSCSI target
  port 20002 address 0.0.0.0 iSCSI target
  20003 port address 0.0.0.0 iSCSI target
  port 25555 address 0.0.0.0 iSCSI target
  hostname rttmoaccess01
  no console logging
  privilege 15
  !
  interface vlan 10
  Name IT
  !
  interface vlan 20
  name UserPCs
  !
  interface vlan 30
  name UserTCs
  !
  interface vlan 40
  the voice name
  !
  interface vlan 50
  Name printers
  !
  gigabitethernet1/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet1/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  gigabitethernet2/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet2/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag

  !
  Default settings:
  Service etiquette: 76BYTS1
   
  SW version 4.1.0.8 (28 August 2012 time 11:17:36)
   
  Gigabit Ethernet ports
  =============================
  Speed 1000
  full duplex
  negotiation
  flow control
  Auto MDIX
  no back pressure
   
  interface vlan 1
  interface port-channel 1-32
   
  spanning tree
  spanning tree mode RSTP
   
  basis of QoS
  QoS trust cos
  Enable IAS

  RTTMOACCESS02 config:

  database of VLAN
  VLAN 10,20,30,40,50
  output
  Add a voice vlan Yes-table Nortel___ 000181
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table Shoretel___ 001049
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  860 port address 0.0.0.0 iSCSI target
  port 3260 address 0.0.0.0 iSCSI target
  port 9876 address 0.0.0.0 iSCSI target
  port 20002 address 0.0.0.0 iSCSI target
  20003 port address 0.0.0.0 iSCSI target
  port 25555 address 0.0.0.0 iSCSI target
  hostname rttmoaccess01
  no console logging
  privilege 15
  !
  interface vlan 10
  Name IT
  !
  interface vlan 20
  name UserPCs
  !
  interface vlan 30
  name UserTCs
  !
  interface vlan 40
  the voice name
  !
  interface vlan 50
  Name printers
  !
  gigabitethernet1/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet1/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  gigabitethernet2/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet2/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  Default settings:
  Service etiquette: 76BYTS1
   
  SW version 4.1.0.8 (28 August 2012 time 11:17:36)
   
  Gigabit Ethernet ports
  =============================
  Speed 1000
  full duplex
  negotiation
  flow control
  Auto MDIX
  no back pressure
   
  interface vlan 1
  interface port-channel 1-32
   
  spanning tree
  spanning tree mode RSTP
   
  basis of QoS
  QoS trust cos
  Enable IAS

  Config RTTMOCORE

  ! Version 8.3.12.0
  ! Last modification of the configuration to Fri Jun 14 13:31:58 2013 default
  ! Startup-config updated Fri Jun 14 13:32:40 2013 default
  !
  start the primary system battery-unit 0: A:
  start a system secondary battery-unit 0: B:
  start the system stack-unit 0 default: A:
  start the primary system battery-unit 1: A:
  start a system secondary battery-unit 1: B:
  start the system default stack-unit 1: A:
  !
  redundancy full automatic synchronization
  !
  Hardware watchdog
  !
  no console logging
  !
  hostname rttmocore
  !
  disposal of battery-unit 0 S4810
  !
  stack-unit 0 battery-group 14
  !
  stack-unit 0 battery-group 15
  !
  interface TenGigabitEthernet 0/46
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  interface TenGigabitEthernet 0/47
  no ip address
  switchport
  FlowControl rx tx off
  no downtime

  disposal of battery-unit 1 S4810
  !
  stack stack-unit 1-group 14
  !
  stack stack-unit 1-group 15
  !
  interface TenGigabitEthernet 1/46
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  interface TenGigabitEthernet 1/47
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  !
  interface Vlan 1
  !
  interface Vlan 10
  Description IT
  Name IT
  no ip address
  Tagged TenGigabitEthernet 0/46-47
  Tagged TenGigabitEthernet 1/46-47
  Shutdown
  !
  interface Vlan 20
  Description UserPCs
  name UserPCs
  no ip address
  Shutdown
  !
  interface Vlan 30
  Description UserTCs
  name UserTCs
  no ip address
  Shutdown
  !
  interface Vlan 40
  Speech description
  the voice name
  no ip address
  Shutdown
  !
  interface Vlan 50
  Printers description
  Name printers
  no ip address
  Shutdown
  !
  Lldp Protocol
  !
  0 line console
  line vty 0
  line vty 1
  line vty 2
  line vty 3
  line vty 4
  line vty 5
  line vty 6
  line vty 7
  line vty 8
  line vty 9
  !
  end

  I would say lets start with one side and obtain communication of work between the two computers on the same stack at RTTMOACCESS01. The port settings for the 1/01 and 2/01 look great both in access mode for VLAN 10. Which IP addresses and subnets you assign to computers?

  5548 to battery power battery connection 10 also appear to not be in a LAG, then we run two connections like that and they aren't in a SHIFT, we create a loop and a single connection will enter a blocking state.

  For the connections between the 5548 and force 10, I suggest to turn them into a GAP. The command should look like this.

  Console > activate

  Console # configure

  Console (config) # (config) # interface tengigabitethernet 1/0/1

  Console (config) # port - 1 automatic mode group

  output console #.

  Console (config) #.

  Do the same for Te2/0/1

  Then we set up this OFFSET to set it up, and I would try to use the trunk instead of general mode mode.

  Console (config) # interface port-channel 1

  console switchport mode trunk #.

  console # permit trunk switchport vlan add 10,20,30,40,50 tag

  The same should be done for the Force switch 10.

  Te0/46.1/46 in a SHIFT

  Te0/47.1/47 in another SHIFT

  Put in the trunk and let the VLANS on the trunk.

  Allows to study these settings and see if we can make any progress.

  Thank you

• PowerConnect 5548 and VLAN

  Good afternoon!

  I'm looking to implement a 5548 in our existing infrastructure. I want to preface this by saying that I am very new to networking.

  I'm looking to have at least two VLANS separated.

  -The first vlan for public sites face. These will have static public IP addresses.

  -The second VLAN is iSCSI traffic. I would like that it won't face public.

  Is it possible to Setup or should I be looking for a different solution.

  If possible, how should I go about setting up?

  Thank you!

  The port that connects to your router should be placed in Trunk mode with the VLAN you want in the trunk port. All ports are in VLAN1 access mode by default, this means that the port that plugs into your routing device is in access mode for VLAN 1 and VLAN 1 has internet access. For traffic VLAN 2 to access routing equipment that you will need to change cela port in Trunk mode and adds 2 VLAN as a VLAN Tag.

  468-page guide details where to put labeling.

  See you soon

• STP and PowerConnect 5548 battery

  HELO,

  I have 2 switches in the stack with HDMI mode. I use these two switches in the access layer.

  To connect to the distribution layer, connect to a switch to a distribution layer and unit 2 to another different switch of the distribution layer.

  Configure ports in the trunk, but I can not activate PLEASE.
  Everything is configured with the same VLAN and the connection works. But the two ports (unit 1 and unit 2) are forwarding.

  I have no other battery that switches PowerConnect and working properly.

  The HDMI connection is in the tree covering weight? or is it just for internal use, the two switches?

  Thank you

  concerning

  The HDMI ports for stacking are not involved PLEASE. When the switches are stacked, they are managed as a single unit.

  I wanted to clarify, when you say that you cannot enable STP, does that mean you don't want STP is enabled? Or, when you try to activate PLEASE, it gives an error / will not?

  You mentioned that ports 1 and 2 remain in a State of shipping, it's the desired status? What status you are waiting for and why?

  Thank you.

• GAL/LACP with several VIRTUAL LANs

  Hello

  I have two switches SG-200-50. I created three VLANS on one and define the place of the other - there is no requirement for routing between VIRTUAL LANs. However, I want to trunk between local networks VIRTUAL using with LACP LAG. For example, A button 1-22 ports VLAN 1 and then 23-24 is the junction for this. 25-34 is VLAN2 and trunking is 35-36. VLAN 3 is 37-48 and 49-50 trunking. I seemed to be able to get 1 VLAN, the default, trunking but no VLAN 2.

  I have a few questions:

  1. the SG-200 will allow you to the trunk several VIRTUAL LANs for another switch?

  2. If so - how? I've lived the documentation and it does not mention explicitly "multiple" VLAN with DELAY.

  3 circuits is possible by a LAG (say 6 ports) happening all the VLANS on the switch?

  So the main question is that I want to achieve is possible on this switch. The reason why I'm doing it is of course of redundancy. Carrying one VLAN on both switches is preferable. I just need trunk correctly between them.

  See you soon! Any thoughts appreciated.

  Scott

  Hi Scott,.

  You had questions, which I copied in red. :

  1. the SG-200 will allow you to the trunk several VIRTUAL LANs for another switch?  Absolutely

  2. If so - how? I've lived the documentation and it does not mention explicitly "multiple" VLAN with DELAY.

  I have attached the Administrator's guide.  The OFFSET rules are defined at the bottom of page 82 of the attached document.

  The 200 series supports four lags, or in other words four groups aggregagted of links.

  3 circuits is possible by a LAG (say 6 ports) happening all the VLANS on the switch?  Yes as indicates it page 83 administrator guide.

  Assign up to eight ports active members to the static LAG.

  So the main question is that I want to achieve is possible on this switch. The reason why I'm doing it is of course of redundancy. Carrying one VLAN on both switches is preferable. I just need trunk correctly between them.

  Personally, I prefer to the trunk on gal differently, especially when you are trying only to achieve redundancy and higher aggregate bandwidth between switches.  It is also relevant to the 300 series as the product of the 300 series is just a richer product.

  You want; "I want to trunk between local networks VIRTUAL using with LACP LAG. For example, A button 1-22 ports VLAN 1 and then 23-24 is the junction for this. 25-34 is VLAN2 and trunking is 35-36. VLAN 3 is 37-48 and 49-50 trunking. It seemed to me be able to obtain VLAN 1, the default value, trunking but no VLAN 2. »

  What about using the ports numbers higher for the uplink between switches, I have no particular reason to use these ports except that they are on the right side of the switch.

  A B switch

  ports ports

  VLAN 1 1-24, 47-48 1-24, 47-48

  VLAN2 25-34, 25-34

  vlan3 35-46 35-46

  LAG ports 49-50 49-50

  The advantage of this is that now you have two ports of the traffic load balancing between switches of series two 200.  I could have more if I want, but I want to keep my simple example.

  Create a static OFFSET, by the sound of it you did already.

  I just used my 300 series switch (SF300 - 48P) as a demo, as I don't have a series 200 switch.  Configuration should be roughly about the same.  In my case, I have four ports GiG GE1 to GE4.  I will use GE1 and GE2 as my two members of a group LAG 1.  May sound a bit confusing, but follow below.

  Added two ports for the DELAY, note in the example below GE1 and GE2 are not connected to another switch, so they showup as ports of Eve;

  Also my 300 series switch supports eight groups of LAG, so captures the numbers 1 to 8 as shown in the following screen.

  

  Now that my LAG is created, you'll notice in the screenshot below that VLAN1 is added automatically to the LAG 1 as unmarked frames.

  Note: circled point, I selected LAG in this menu drop-down and then click Go.

  Note: 1 in the Red rectangular box represents GAL Group 1, which consists of GE1 and GE2

  

  Now, I add 2 VLAN group LAG 1 by selecting 2 VLAN selected then LAG and then click go, the following screen came.

  

  I clicked on the button marked radio in the rectangle above, to allow VLAN 2 send labeled on group GAL 1 ethernet frames.

  And so on for the other VLANS I migth.

  My methodology or train of thought, was to allow of vlan1 to just send frames unmarked on the Group LAG 1, but any other VLAN later is marked on the Group 1 GAL.

  You should be able to do exactly the same thing on the other switch 200 series.

  in my example, as I then simply take some CAT6 or CAT5e cables and connect GE1 on a 200 series switch to other Ge1 200 series

  I connect then GE2 on a 200 series switch to other Ge2 200 series.

  Now I have the aggregation of links and balancing working between switches.

  Hope this helps

  Best regards, Dave

• behavior of vSwitch in Virtual Switch Tagging (VST mode)

  Hello

  I have a problem with a vSwitch within an ESX 4 environment.

  On my vSwitch is a virtual network, where the port group has been linked to a defined VLANID, so for a real-world scenario, a physical switch has a port configured in access with a predefined VLANID 8021q mode.

  In my scenario the port configured in this way can receive frames already labeled (the generic behavior is that the port receives the unmarked frames). An access of a switch port generally accepts executives 8021 consistent q If the vlanID is the same as configured in its behavior (t - it - Cisco http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli_rel_4_0_1a/AccessTrunk.html), otherwise the switch removes them.

  VMware says this:

  "Switch ports group virtual tags all outbound frames and removes the tags for all incoming frames." It also ensures that the frames on a VLAN do not leak in one VLAN different. »

  OK I agree with this, but if the virtual switch receives a frame already tagged (with the right tag) must be just to not let him down, as Cisco?

  The switch ports group virtual tags all outbound frames and removes the tags for all incoming frames. It also ensures that the frames on a VLAN do not leak in one VLAN different.

  Now, I also checked the actions for the ordinary vSwitch:

  A virtual machine sends frames unmarked on a portgroup with a specified VLAN id (for example, 300) = works

  A virtual machine sends tagged frames (VLAN 300) on a portgroup with the same VLAN id specified (for example, 300) = failed

  A virtual machine is sending of tagged frames (for example, 300) on a portgroup with VLAN 4095 specified = works

  A virtual machine sends frames unmarked on a portgroup with VLAN 4095 specified = fail

  If the vSwitch behavior is very similar to the distributed vSwitch, that it does not accept any marking made by the virtual machine in regular trade, even if it is the VLAN correct. If affecting portgroup VLAN 4095 it throws frames marked, very likely because we cannot specify any "VLAN native. I think that's the answer to your original question.

• 5548, 7048 - PowerConnect backup SNMP configuration

  Hello

  I Powerconnect 5548 and 7480 switches and I would like to know if it is possible to backup with TFTP and SNMP commands configuration files, like I do with my cisco switches?

  Thank you.

  You should be able to use rlcopy which is OID.1.3.6.1.4.1.89.87

  Location of the source Rlcopy.1.3.6.1.4.1.89.87.2.1.3

  Rlcopy the ip address of destination.1.3.6.1.4.1.89.87.2.1.9

  Updates of the firmware also contain the mib files, so you can find the OID http://www.dell.com/support/home/us/en/04/Drivers/DriversDetails?driverId=JRCF6&fileId=3365034200&osCode=NAA&productCode=powerconnect-5524&languageCode=EN&categoryId=NI

• Dell Powerconnect 5448 a reference on the vlan by default

  Hello

  Just a question.  A Dell Powerconnect 5448 switch will act as a home if its interfaces are configured with 1 interface connection to a primary switch that has the interface is 'access to the interface mode' by default with a vlan?  It will work with all its switches on vlan interface of uplink or would you need to configure both as the trunks to allow access vlan to work and this switch uplink?

  The 5448 is a layer 2 switch, which by default has a VLAN native of 1 with all interfaces in access mode for the native VLAN 1. On the VLAN native all frames are frames unmarked. So now that your uplink to the other switch port, all the info will be sent without label, which means the other switch will receive the unmarked data and then place it in the VLAN that is in access mode. Communication should work this way.

  However, I think using a network connection between the switches. The trunk port is used to connect the devices up-to-date with the switches / VLAN together and allow several VLAN tagged fell on it. Looks like you already have several VLANs on the network, and having a network connection will allow you to expand on it. At the same time everything that is on the VLAN native is always through the trunk to the other switch and will stay on the VLAN native.

• LV: Sending 'sync' to get synchronous acquisition of CDN

  Hello @ all

  First of all: my knowledge on the bus CAN generally is not very good, so excuse a description of the possible problem.

  My task is to read the devices CAN messages. This works very well for devices that send their messages 'stand alone' with a fixed repetition rate (here: 100 Hz).

  But other devices do not send their messages with such a high repeat rate. They send their message only until they come in an overflow (here: after 150ms). I ve heard that I send a message "sync" for devices to get their message across. This means that I have to send the message of synchronization with the 100 Hz for the acquisition of 100 Hz.

  My question: How can I have to set such a two-way CAN transfer? Of course, I can send a synchronization message and read the reply. But what it takes when I want to read for example 10000 messages? I Don t want to trigger it by software because of the accuracy of the timer.

  What should I just start "CAN read.vi" and the parallel of "CAN write.vi"? Or is it possible to start the write.vi and the read.vi at a time determined, to obtain two parallel functions?

  Tanks so far.

  Hi LittleJoe198,

  I'm not quite sure what exactly is the problem. I only know "sync messages" in the context of CANopen. But your question indicates that you are using the API of frame. Maybe you mean sending frames remotely?

  You could use the CAN objects to transmit data periodically using material timing (only supported on PXI/PCI/PCMCIA-CAN cards). Take a look in the example finder LabVIEW (hardware category of entry and exit > CAN > frame API > base), "CAN transmit - periodic.vi.

  It is not a problem sending and receiving on the same port, see example 'send receive same Port.vi. "

  You should also take a look at the manual CAN Hardware and Software (START > programs > National Instruments > NI-CAN).

  What kind of material CAN do you use?

  Let me know if you have any other questions.

  Kind regards

• Stacking question: can I combine a stack of 5548 with a stack of 5524?

  Can I combine a set of four switches PowerConnect 5548 with a stack of two switches PowerConnect 5524? I don't know to ensure they are running the same firmware, but I didn't not see the documentation on the size of maximum stack or between models stacking limits.

  Thank you.

  Yes, you can stack 6 switches together, any 5500 stack with any other, to a maximum of 8

• LACP LAG POWERCONNECT 6224

  Hi I m ussing a powerconnect 6224, I have equipment that works as a switch and it has two ports glued with LACP, when I connect this device to the POWERCONNECT and send a ping there is no answer, one that with a laptop computer connected to this port, it responds to the ping command. Can help you with this? Here is the configuration of the POWERCONNECT. Thanks in advance.

  Console (config) #interface vlan 32

  Console (config-if-vlan10) #ip address 10.163.101.4 255.255.255.252

  Console (config-if-vlan10) #routing

  Console (config) #interface ethernet 1/g3

  mode console (config-if-1/g1) #switchport general

  Console (config-if-1/g1) #switchport general allowed vlan add 31

  Close, more like this.

  Console (config) # interface range ethernet g2

  Console # channel - group 1 automatic mode

  output console #.

  Console (config) # interface range ethernet g3

  Console # channel - group 1 automatic mode

  output console #.

  Console (config) # interface port-channel 1

  Console # switchport mode general

  Console # switchport general allowed vlan 201 tagged

  Make sure that there are at least two ports in each LAG.

• PowerConnect 5548P appears dead - how fix?

  Switch on my bench OK, separated from all recent messages; I have a Dell PowerConnect 5548 P sitting here.  Apparently, my predecessor, one of our technicians said "he thought it was bad."

  I have already hooked up to the console cable and started.  I only get the first message:

  Checksum test Boot1...

  Then nothing after.  Is there a reset, or diagnostic I can run before you go about things with the support of Dell, or is it pretty much "stick a fork in there, it's done.

  Looks like it might actually be a firmware or hardware problems. I would start with the first try re-flashing the firmware through XMODEM.

  http://www.Dell.com/support/drivers/us/en/19/DriverDetails/product/PowerConnect-5524?driverId=371Y4&osCode=NAA&FILEID=3324507244&LanguageCode=en&CategoryID=NI

  In the firmware download through XMODEM update instructions there.

  If the firmware does not help, you are probably looking to a hardware problem. You mentioned the fans, which makes it look like the LED fan on the front of the switch?

  Thank you