PowerEdge 1855 GbE Passthrough

Hello everyone. I'm new to the whole Blade Server system, and I have a question on the maps of passthrough GbE 1855. How does it work? I wrongly assumed that I could simply plug into port 1 or the other of the two cards passthrough I installed and they have to be connected to the first blade. I looked through the DRAC, I installed and got no help from the configuration. I should mention that I have a KVM analog currently, what might be at the origin of some of the issues. I ordered a digital camera, but it is not until next week. Any help would be greatly appreciated!

Sean

Sean,

Just to clarify. The PHY module will not bind if connected to an infrastructure of 10 or 100 MB that the PHY module only supports gigabit speed.

In addition, the layout of the ports of the module are

9-7-5-3-1

10-8-6-4-2

Just to make sure that you have been truly connected to port 1.

Tags: Dell Servers

Similar Questions

  • Cluster nodes cannot ping each other

    Hello

    I recently put one of our old clusters online it's a server poweredge 1855. I work at 5 knots, and there a PowerConnect 5316 M switch on the back. 5316M has only 1 cable connecting the switch to uplink.

    Each blade has 2 NIC one of them is a NIC, with a normal IP on our range of normal production. All blades can ping this address each other, and they all have internet.

    The other NETWORK adapter is what I use for live migration, or pulsation of cluster or something... Whatever it is, it has a different range with no gateway (172.50.1.x)

    Now 3 of the blades can all ping eachother, but not the other 2. And 2 that can not ping, can ping each other. It seems that the 2 are on the same VLAN, and the other 3 are on the same VLAN.

    The problem I have, is the switch shows them all on the VLAN by default... and one thing that I can't work... If the servers all have 2 network cards, but there are only 10 ports on the internal switch?... so, how can I set or the other card NETWORK on one VLAN different?

    The configuration of the switch is here:

    console# show runspanning-tree mode mstpspanning-tree mst configurationinstance 1 add vlan 1,15,900instance 2 add vlan 2-3name PDSNetherlands1revision 900exitspanning-tree mst 1 priority 57344spanning-tree mst 2 priority 57344interface port-channel 1description 'LACPGROUP-M5316M-SW2'exitinterface port-channel 1switchport mode generalexitvlan databasevlan 2-3,15,238,328-329,501,638,900exitinterface port-channel 1switchport general allowed vlan add 15exitinterface port-channel 1switchport general allowed vlan add 900exitinterface vlan 2name "PDS Internet"exitinterface vlan 3name "PDS Wireless"exitinterface vlan 15name "PDS ServerInfrastructure"exitinterface vlan 238name "SHELL GI-Desktops"exitinterface vlan 328name "SHELL Unix-Desktops"exitinterface vlan 329name "SHELL Windows-Servers"exitinterface vlan 501name "SHELL Linux-Desktops"exitinterface vlan 638name "SHELL IP-Telephony"exitinterface vlan 900name "PDS Workstations"exitinterface range ethernet g(11-16)channel-group 1 mode autoexitinterface vlan 1ip address 10.254.254.253 255.0.0.0exitip default-gateway 10.0.0.1logging 10.0.1.56  severity debugging facility local0username admin password 5ebe2294ecd0e0f08eab7690d2a6ee69 level 15 encryptedusername admin_jon password ea4462b55746d29a4a0fc44c3db06b95 level 15 encryptedusername administrator password 22d4734b069e91ceebdf297701005b28 level 15 encryptedsnmp-server community private rwsntp client poll timer 60sntp unicast client enablesntp anycast client enablesntp broadcast client enablesntp server 64.90.182.55 pollconsole#
    
    Any help would be appreciated, I cannot complete the cluster validation wizard until i can crack this ..
    
    Kind Regards,
    
    Jon
    

    This document does a good job of showing how interconnections.

    www.Dell.com/.../ps3q05-20050163-Brundridge-OE.pdf

    Module e/s 1 goes to port 1 and i/o 2 module goes to port 2 of the LOM standard.

    It is therefore useful to check what ports are used by the server. If the 3 are on port 1 and then the other 2 are on port 2, try to get all the 172.50.1.x addresses assigned to port 2 for example.

  • The console error

    I get the error message "unable to connect to the MKS: unable to connect to the xxx.xxx.xxx.xxx:902 server ' port is sometimes 903.

    I found a few solutions but none worked. I get this error on the vSphere and webaccess client.

    Before we get to this error, I want to make sure how I want this configuration is possible.

    I work with Dell Poweredge 1855 with two network cards on each blade. I want to install a private network (say 10.0.x.x) for the Vcenter communicate with ESX servers. If a NETWORK adapter on each blade will be DHCP on the same private network as one of the network cards on the blade of Vcenter.  The other NETWORK adapter on the Vcenter blade will be one of my public Ips (say 73.129).

    I have 5 fps public static - 73.129/133 & my private network is DHCP

    Server-


    O/S-                                            -
    NIC 1-.


    NIC2

    Blade1-


    Win2k3/Vcenter--73.129-.


    10.0.10.x

    Blade2-


    ESX                                              -


    73.130-


    10.0.10.x

    Blade3-


    ESX                                              -


    73.131 - 10.0.10.x

    blade4-


    ESX                                              -


    73,132-


    10.0.10.x

    Blade5-


    ESX                                              -


    73.133-


    10.0.10.x

    I want the service console on each ESX can only be accessed by the private NIC 2 IP. NIC1 public/static IP I want the virtual machine to use.

    I want that the only way to manage the esx servers is to use vSphere linking the vCenter on blade1. Is it possible to install?

    I have all this Setup NICS, switches, Ips, but I get the above error when I try to use webclient and vSphere via Vcenter blade service.

    I couldn't find much on this particular situation, but if you find something or have any ideas I would greatly appreciate the info or a link. Thanks in advance.

    Everyone,

    As flyingfreak has problems that are more related to its installation, I took the time to make one on a chat. For anyone reading this later the solution was to create virtual machines in ESX/ESXi servers and place them on a switch vNetwork public. It has no way for a person to own the servers and have the means to infiltrate the private network.

    Flyingfreak if it doesn't have you helped solve the problem please repost on this and the community will join in to help. If this does not solve your problem please knock "responded."

    Thankx!

    Jimmy Dean

  • PowerEdge 1850: Need to add storage: ISCSI or SATA controller or? : Host does not support configuring passthrough

    I have a (non - VT capable) PowerEdge 1850 which took an ESXi 4.0 U1 (Dell Version) installation like a champ.  I know that I probably won't be able to have 64-bit clients.

    In this box of ESXi (laboratory

    Server) I have:

    • 2 x 73 GB SCSI U320 drives in RAID 0 array.

    • 6 GB OF RAM ECC

    • 2 x 1 GB NIC

    • 2 x PCI - X slots (PCI - X slot 133 MHz and PCI - X connector 100 / 66 MHz)

    I want to add more space "VM/Guest" and not spending too much money.

    What is my best solution?

    1. Find a compatible ESATA 3Gbps controller card (I have a nice 500 GB SATA Drive laying around)? ...

    2. Or should I get out an old box and throw a Gigabit NETWORK card and a SATA inside player and try my hand at Openfiler? I have yet to try it.

    3. ... Or... something else?

    Could someone help me hand choose either a PCI controller card - X ESATA/SATA (is - it possible or am I limited by my attached picture?) or a NETWORK card for my spare box (if it is not an old)?  I understand "_ _passthrough configuration"allows my virtual machine to hardware on the host computer directly, but I'm not clear how this effects my plans you want.

    I read:

    .. .but I am suspicious of money sinking into the material lest my PowerEdge does not support the Configuration PassThrough (does it matter?)  I still have to load a single guest.

    Thanks a lot for your time in advance!

    Get started with what you have. Do not pass anything. Set up the old PC you have as a NFS storage device. Use openfiler or? That will allow you to do some investigation/tests you want to do. Keep your eyes open for a local RAID controller or on an old server with lots of fast scsi storage you can add such as NFS or?

  • ESXi 4.1 - Dell Poweredge 2850 - tape backup - host does not support configuring passthrough

    I'm trying to get a tape backup to work on my ESXi host, so I can save my win2003 VM.  I get this error under VMDirectPath, 'host does not support configuring passthrough ".  Under Configuration > storage adapters > I don't see my tape drive listed.  Also, I noticed that my SCSI controller card is NOT on the HCL (Adaptec 39160).  See.  This is probably why passthrough doesn't work.

    So, I was thinking of buying this one (Adaptec 39320) because he seems to be on the list.  This will solve my problem or is this server too old for passthrough to work?

    To use VMDirectpath on an Intel Server chipset used must support Intel VT - d (Directed i/o).   I don't think that's the case with the models of 2850, but if it was you would see an option in the BIOS to enable this.  It is a separate option of VT - x, which allows the host run the 64-bit clients.

  • PowerEdge T430 - GPU solutions to improve graphics performance ESXI

    Are there solutions GPU compatible with the T430 that would be good to improve graphics performance on virtual machines that run on ESXI?

    AMD over-pants S-line cards for virtualization servers seem to be the right solution, but they are expensive.

    As an alternative to a GPU for virtualization, I am willing to consider the installation of a constant slope workstation GPU and do passthrough material between the GPU and a specific virtual machine.  The T430 and other PowerEdge servers seem to be 2 x 3 PEG connectors to power regular graphics cards so I did not know if there is a solution for this path.

    I'd appreciate your comments.

    Hello

    There is no official support of GPU for the T430. Some cards that can work at AMD, Nvidia W7000 grid K2 and K20.

  • Path of VMdirect and Dell Poweredge T110 II

    No matter who got the e/s working on the Dell Poweredge T110 II DirectPath?  On the Summary tab, I have a warning indicating that the host hardware does not support the DirectPath of IO.  I have virtualization enabled in BIOS.  On the configuration tab I also have the error "Host does not support configuring passthrough" my processor is a intel Core I3-3220 3.3 Ghz.   If someone got it works with the latest BIOS?  I have to use USB external drives for storage of files and not facing one of the internal locations and just use the internal slots for my build of ESXI raids.  Any help in this would be appreciated.

    Thank you

    Stephen Bailey

    I discovered that my CPU does not support directpath i/o, so there is no hope in getting this work.  I found a work-around however to get a crossed USB device.

    While VMdirectpath i/o would be nice there is also a USB device transfer which is another way to allow direct communication with a hardware device to a guest operating system.  ESXI allows transfer USB Device (this can be done without vmdirect path).

    When I first tried this (I didn't know at the time that ESXI 5.0 did not support USB 3.0) device usb 3.0 had not passed through and I thought it was because of a misconfiguration of the vmdirect path.  I did some additional research after I discovered that my processor didn't support directpath and found documentation for transfer of USB device.  All I had to do was add the USB controller to my guest operating system configuration then added a "usb device" to the configuration of my guest operating system who found the name of the device is connected.  I was then able to add a USB 2.0 device and my guest what OS is very clear.

  • How vm can my Dell poweredge T110 run?

    How my Dell Poweredge T110 yourself run the specs are

    Processor Intel Xeon X 3450 (2.66 Ghz, 8 MB Cache, 95W TDP, Turbo, HT), DDR3 - 1333 Mhz

    Neniry 8GB (UDIMM rank double 2 x 4 GB) 1333 Mhz

    HD 1 x 250 GB 3 x 1 TB SATA

    1 x adapter Server Intel PRO 1000PT Port GbE, Cu, PCIe x 1

    a friend sayd I can run only 2 VM

    You can see one of the 2 CPU servers with 4 or 6 cores per processor. Similar to your T110 would be the T410. Add the second processor enough RAM and hardware raid controller. You can have SAS rather than SATA drives and you're better off with several discs smaller than smaller disks for better performance.

  • Usb device ESXi 4.1.0 through material passtrough on Dell Poweredge R510

    Hello.

    I am trying to use one of the four usb ports on a Dell PowerEdge R510 inside an ESXi 4.1.0 260247 host for a XP Prof invited. I have the following PCI devices:

    http://communities.vmware.com/servlet/JiveServlet/downloadImage/10539/esxi41.jpg

    With each of the devices ID 00:1 a. 0 00: 1 d: 3 comments XP correctly will not start. When I attach the 00:1d.7 device boots comments, but then there is a problem with the device driver. I tried the chipset drivers for W2003 from dell (http://support.euro.dell.com/support/downloads/download.aspx?c=de & cs = debsdt1 & l = a & s = bsd & releaseid = R269378 & SystemID = PWE_R510 & servicetag = & os = WNET & osl = GE & deviceid = 17195 & devlib = 0 & typecnt = 0 & vercnt = 2 & catid = 1 & impid =-1 & formatcnt = 0 & libid = 27 & typeid =-1 & dateid =-1 & formatid =-1 & source =-1 & 396483 = starts) , but no luck.

    I know that there is now a direct usb support in ESXi 4.1, but my usb device is not supported through this new feature.

    In addition, I'm looking for a PCI Express RS232 serial card that works on this server equipped with passthrough for a XP guest.

    Thank you

    Michael

    Try to ignore this ridiculous list, it's a bad joke for devices on the external bus like SCSI and USB.

    I've successfully used the USB feature in 4.1 for a device not on the list (in fact, he was a device of type modem/serial port), more precisely a key entropy of Simtec.

    So anyway, try your device with the USB function before mingling with the much more fragile PCI passthrough feature.

  • ESXi Passthrough disorder

    Hello

    So I tried activating the relay for an external USB device. Now, I can't UN-configure the passthrough devices.

    The steps I took were:

    1. Enable the USB ports in vSphere client under Configuration - & gt; Advanced settings, and then check each box USB

    2. Connected the USB device

    3. Open the machine virtual and added a USB controller

    4. Restarted the server ESXi

    Rebot took 20-30 minutes and made the VM do not seem to see any USB device, so I decided to remove the configuration, are the steps that I took:

    1. Stop the virtual machine, I tried to add the trundle for decision-making

    2. Edited settings and removed the USB controller

    3. Reboot the machine virtual and checked the Device Manager

    4. Stop the virtual machine

    5. disabled USB ports in vSphere client under Configuration - & gt; Advanced settings and then unchecking each box USB

    6. Restarted the server ESXi

    Passthrough devices are always checked that whenever I do it, and start time are always very slow (20-30 minutes). Any advice on the steps I can take to remove configured pull-out decision would be greatly appreciated.

    Material:

    Dell PowerEdge R610

    MD3000i

    Software:

    ESXi 4.0.0 build 181792

    vSphere 4.0.0 build 162856

    Glad to hear you have it worked.   I've set up some notes on the resolution of this problem.  It's a little late for your situation, but I hope it will help others who find themselves in the same boat - http://www.vm-help.com/esx40i/VMDirectPath/fix_config_issues.php.

    Dave

    VMware communities user moderator

    New book in town - Start Guide quick vSphere -http://www.yellow-bricks.com/2009/08/12/new-book-in-town-vsphere-quick-start-guide/.

    You have a system or a PCI with VMDirectPath?  Submit your specifications to the unofficial VMDirectPath HCL - http://www.vm-help.com/forum/viewforum.php?f=21.

  • Satellite A655-11 t - GbE card won't get a dynamic IP address

    I have improved my family Windows 7 SP1 on a Toshiba A655-11 t.
    Then, on each reboot the GbE onboard, if enabled, will not get a new IP from a DHCP server.
    Without doing anything with the adapter, renewing the IP wifi from the same DHCP server, causing GbE NIC get a new IP address also.
    This allows me to disconnect wifi and continue to work on the GbE.

    Any ideas what has done to introduce Windows 7 SP1 to break the DHCP client feature? This can be corrected?
    Thank you.

    And what about Microsoft on this issue?
    I guess you're good work laptop Toshiba, right?

  • HP Envy laptop: Realtek PCIe GBE Family Controller BUG

    Bug Windows 10 Ethernet (Realtek PCIe GBE Family Controller)

    a known bug, my laptop after a few windows updates stop to work as described on the microsoft community...

    The network stops working after a few seconds after the "Repair Procedure. Then runs, but the repetitions of history...

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-networking/Windows-10-Ethernet-bug-Realt...

    HP HEELP ME!

    Hi @flash370z,

    E-roqis not available right now, so I'll help you.

    Please see this document for Troubleshooting Wired Home networks (Windows 10).

    Here is a link to download the latest drivers from the network. Local Area Network (LAN) Driver Realtek

    Please keep me informed of the progress of things.

    If you need help, let me know and I will gladly make all that I can to help you.

    Please let me know if that solves the problem by marking this post as "accept as a Solution.
    To simply say thank you, click the Thumbs up below!

    Thank you.

  • SOLVED: Slow wireless internet passthrough after firmware update

    If I first bought a Nighthawk in July 2014 and it was great for a while. Then in the notice happened a few months my streaming services are jumping and more than usual buffering (which was almost never with the Nighthawk).

    I have a connection of 110Mbps (Comcast and through a SB6141 modem), but all of a sudden was only getting 10 Mbps (or less) passthrough on 5 G wireless band (at the beginning of the speed test would sometimes up to 50 Mbit/s, but on a few seconds would fall to nothing..)

    Cable speeds were very good. Always 110Mbps +. Tried several different channels and factory reset the router, wireless speed was still slow. Connected to the Netgear website and submitted a support ticket within 2 hours they sent me with an RMA number and the next day a new unit has been FedEx would be for me. Support rep Tech says it's a problem of material known in some units... I was super impressed with the customer service, it was seriously a no replacement of hassles that took every 15 minutes of my time.

    EXCEPT when I got the replacement router in the next few days, he had the SAME PROBLEM. As soon as the new router is on and I'm connected, I've upgraded to the latest version of the firmware, done a factory reset and down Speedtest. And I had the same problem: speed internet passthrough on all my wireless devices has been terrible. Less than 10 Mbps when I have a connection 110 + Mbps. (Wired speeds were great, it was not a problem of modem or provider).

    Again contacted support and they asked me to download the latest firmware on laptop and upgrade the router manually, do a factory reset before and after the upgrade. They also told me to try to disable WMM (made no difference speed passthrough, but lower my laptop connection between 433Mbps to 54Mbps speed!).

    I tried this... still slow passthough wireless speed.

    The only thing that has changed since I first got a Nighthawk in July 2014 (and I've run speedtests then and had a speed 110 wireless + Mbit/s at the time), is that the firmware has updated several times... makes me think...

    I downloaded the Netgear support the past 5 versions of the firmware for the Nighthawk. http://downloadcenter.netgear.com/en/product/R7000#sear...

    I then manually downgraded the Nighthawk to each previous version (do a factory reset before and after each installation) and ran Speedtest every time. Once I have got down to the R7000 Version - V1.0.3.24_1.1.20 (released 12/02/14) and ran a Speedtest, the PROBLEM has BEEN RESOLVED. Speed wireless devices (laptop, HTC a M7 and iPad Air 2) were all back up to 110Mbps or more!

    Hope this experience helps someone else... If your are affected by the passthrough slow internet speeds and it is not your connection speed (i.e. radio parasites) that is the question, there seems to be a serious problem with the latest latest versions of couple... Try downgrading to the R7000 firmware version - V1.0.3.24_1.1.20

    UPDATE: Yes, I actually tested the speed with several different devices (a laptop HP HTC a M7 and Nexus 9) each on 5G band, all compatible with the latest updates ac. I also used a few test sites of different speed (speedtest.net, comcast speedtest, cnet speed test), not had the same result all devices and hosts.

    However, I actually got in touch with Netgear L2 support for the last month... beta test a few different versions of the firmware of the Nighthawk and even spend more than an hour on the phone one night with a nice guy who told me he was on an island in Southeast Asia, part of the Philippines... This is where Netgear technical support is to halfway between China where they build them and Taiwan where engineers are. After trying all tweak he could think for an hour and not get better speeds wireless, he finally dropped out and wished me a Merry Christmas lol. Not one of these beta firmware made a bit of difference, and I hate the hours that they made me screwing around with them!

    BUT today, they released vR7000 - V1.0.4.14_1.1.50 http://support.netgear.com/product/r7000

    And to my surprise it actually worked! Not only my high speed wireless is returned (120 + Mbps)

    http://www.Speedtest.NET/my-result/4078979293 (laptop)
    http://www.Speedtest.NET/my-result/a/1131321713 (nexus 9)
    http://www.Speedtest.NET/my-result/a/1131332778 (htc a m7)

    but also my Seagate SRD0SD0 previously incompatible (3 TB) USB 3.0 external hard drive works now, too. What a bonus! The reason I bought the Nighthawk was to use as Server DLNA and the monster external HD I picked up 6 months ago only was on the long list of those incompatible with this capricious router.

    But now everything works (at least for now).

    P.S. Maybe it's in my head, but I swear to you that since the last firmware update when running speedtest now or file transfer (while heavy streaming) I can hear the router doing a greater slope electric buzzing/hissing noise is a little disconcerting... I'm not sure my brain fried by overclocked wifi will be worth a high speed in the end...: eek:

  • iTunes 12 sound does not work with ac3 passthrough

    I have an Intel DX79/Xeon 2, CPU 0GHa with a NVidia GTX680 graphics card.

    I use an HDMI output directly to a Denon surround amplifier. Everything had been working well for a few years but recently I reinstalled Windows 8.1 and I found the passage of in surround AC3 stopped working with iTunes.  Movies of the source that I use have 5.1 channels and used to work.  Nothing the silence I fear when "Prefer AC3" is now selected.   The material has not changed - just a re-installation of Windows with the latest version of iTunes 8.1 and NVidia version 359.06.  The installation is completely vanilla flavored outside these two packages being installed.

    So, I added PowerDVD and tested with a couple of BluRay discs.

    PowerDVD works well with AC3 pass by - the problem seems to be limited to iTunes.  Stereo mode in iTunes works fine.  I tried the "Old video card" version iTunes without success and I tried without downgrading the video version card / audio driver for NVidia 344.75 (a version I know that used to work for about a year back) all to nothing does not).  I also tried version 12 iTunes and encountered exactly the same problem. I think that maybe iTunes and the driver NVidia do not play well together.  All the world is this problem?  I tried to contact Apple support, but it generates an error with a hexadecimal error code large enough and said "try again later...". ', Useful suggestions are welcome!

    Hey there,

    I just saw your post - I had the same problem and posted my fixed on a different thread, here: AC3 Passthrough works does not in 10 - bug and workaround windows

    I hope this works for you

  • Realtek PCIe Gbe family controller findFile error absent during the installation of the driver

    Model: HP ENVY TouchSmart 15-j052nr

    Question: Has lowered Windows 8 for windows 7 and

    (1) question:

    everything works fine except no USB 3.0 ports are working. I see an unknown device and it is not able to find the driver.

    Unknown device: Details column has ID Hardword

    IUSB3\ROOT_HUB30 & VID_8086 & PID_8C31 & REV_0005 & SID_1962103C

    IUSB3\ROOT_HUB30 & VID_8086 & PID_8C31 & REV_0005

    IUSB3\ROOT_HUB30 & VID_8086 & PID_8C31

    I tried to install https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=22824 but it did not help.

    (2) question

    Another question: the Ethernet controller is missing the driver and I get findfile failed when I try to install the driver

    Controller Realtek PCIe Gbe family

    Error: http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/findfile-failed-the-realtek-netw...

    I tried pluggin ethernet cable when installing the driver also but no result

    You are the very welcome.

    If you have not installed c of the first Intel chipset driver and restart.

    https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&ProdId=816&DwnldID=20775&keyword=chipset+installation+utility&lang=eng

    Then, I would try the driver directly from Realtek on the link below.

    You want to download and install the second driver file on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

Maybe you are looking for

  • RND4210 ReadyNAS 'your NETGEAR storage space is not accessible from this computer... »

    Hi all First time poster here. My uncle died in November and he had this NAS device in his office. On the back it says RND4210 ReadyNAS but do not know what version or model or something else. I got to download RAIDar, but now I have done that and it

  • System UI missing tuner

    Hey guys,. I looked through the settings menu when I published that was missing the tuner of the user interface of the system. I continued to try to find the parameters and features when it hit me that they all came from the tuner section. I know tha

  • the DFS replication add new servers to an existing rule

    I have an existing replication and 2 new servers I want to add new servers to the old rule and start replication Once everything is running I want to remove the old servers and leave the new

  • Error message "a required CD/DVD driver is missing" - install Windows7 via USB

    So I recently built a new office because my laptop fried itself, and I ran into the famous message "drver cd/dvd required is missing."  I tried many solutions to internet: change SATA AHCI, ATA, IDE; starting with only the hard drive; and the solutio

  • BlackBerry Smartphones cannot send message

    I get my email fine, but I can't send messages. The status of the message, for those that tried to send, but returned with a red, is x: Message included an invalid address. the first time I got the message, I tried to send to another person and that