PowerEdge R720 - could not detect hard drive

Similar Questions

• Tecra S1 - Bios does not detect HARD drive

  Hi, first time poster, long drive date.

  I have a friends laptop with me an old S1, its hard drive has failed. (Even tried it on my USB adapter to diagnose).

  I had another IDE HDD which works like a dream.
  I can even install Windows up to a point with the exception of when the computer wants to do the first restart of the second phase of the installation. (Not on CD).

  In the bios the HARD drive is not detected a 0 MB for the read command.
  I tested the USB HARD drive. So works perfectly. will try another hard drive there tomorrow see what is happening.

  I tried the recovery CD aswell. But she also can not detect the hard drive.
  Finally, I even reflashed the Bios even if it was the last version 2.50.
  Still did not change.

  If I'm just at a loss here. Tomorrow I'll do the following.

  Try a 3rd HDD IDE into the machine.

  Opening of the case and see if I can find the CMOS battery to replace or remove for a minute or 2 to see what is happening.
  Is obviously a problem of bios of the HARD drive is detected. Has anyone ever encountered this before?

  Windows / ERD Commander / Partition Magic 8 all finding the end hard drive.
  Thanks for listening to my dribble that I feel like I'm banging my head against a wall being close.

  Kind regards

  Dave

  What drive did you use and what size it it?
  I think that not all HARD drive would be compatible because of the 28-bit LBA.

  The 28-bit LBA supports hard disks up to 128GB and if the IDE controller supports only 28-bit LBA then it may happen that more large drives would not be recognized by the BIOS.

• 15 - f039wm: BIOS does not detect hard drives until it performs a diagnostic search

  I was handed a 15-f039wm laptop to watch and I recognized immediately the hard drive was bad, complete failure - no detection and would not pass the built-in diagnostics. I have removed the drive from the laptop and confirmed that the car was bad on a separate system. I ordered a new drive, went with an SSD and put the new drive of the laptop. I checked the cable was sitting correctly on both ends and for good measure he reinstalled on the motherboard as well as on the drive itself.

  Then I tried to re - install Windows 8.1 with the laptop provided with Bing, but when it came time to select the hard disk in the Windows Installer screen, no disks have been detected. I tried to load the drivers for the drive recognized, but nothing has worked. I then tried to start other diskettes of Windows (7 & 10) and the same problem arose, no drive detected. For fun, I loaded Hiren's Boot Disk and tried to see what I could do, and oddly enough the drive detected several times.

  Then, I decided to go back to the integrated diagnostic tools (F2 at startup) and see what would happen. Hard drive has been detected and passed the Quick Test. I have a Windows install CD in and after that I left the screen he ended up launching the installation disc. I decided to try just a new set of drivers to see if the disc could be detected, but that the disc was already detected and just sitting there, ready for the installation of the software.

  I have installed 8.1 on it and did the upgrade of Windows 10 to the owner and I noticed something serious.  Whenever I restarted (key here being a full reboot), the drive was not detected and I would get an error in DEVICE of START-UP INACCESSIBLE when he tried to load Windows. I ended up to play with the drive and launch the troubleshooting menus command prompt.

  I tried to run diskpart, and when I typed "list disk" inside diskpart and he told me that there are no drives found. Large.

  I took once more apart from the laptop and reinstall the drive again and the same problem happens again. This is where it gets a little weird. I ran Diagnostics on the hard drive again and just canceled check out out and Quick Test and let it boot. It starts very well.

  I thought so at this stage it is a bug in the BIOS or something and decided to flash F.25 Rev.A to see if that would help. No, the problem persists after BIOS update flash. I decided to just go ahead and order a new cable to see if the cable is the issue. Is there anything else I can try? Anyone have this problem, it is rather strange to me, and I saw a lot of machines to act strangely.

  So, to summarize:

  Hard drive is not detected at least that I force diagnostic analysis of any type on the hard drive and come out and let it boot.

  What I tried:

  New hard drive

  Reconnect the hard drive

  BIOS settings - boot order, security keys allowed Secure Boot on / off, Legacy Boot on / off, (there no option of detection or ahci in the BIOS).

   

  Many windows install environments, non-windows - disk environments is ever detected by the BIOS, I guess

   

  Flashed the BIOS updated

  Reinstall Windows (back to 8.1 with Bing and question persists, persists on Windows 10 institutions)

   

  DiskPart on Windows Installer (shift + f10 - prompt "diskpart" command, then in diskpart: 'list disk' which wouldn't say no disk).

   

  Ordered a new cable (pending on this one)

  What gets me, is that it works whenever I have diagnostic scan before starting. Every time. It fails on a restart cold without doing so. I looked on the Board for the damage of physical strength and the liquid, but do not see anything to really. I'm guessing that it was abandoned. Any ideas on what else to try? I'm running out of ideas on this one.

  Try the new cable, but I think you look a very bad mother board it.

• Cannot install Win 8 - Satellite Pro C660 does not detect HARD drive

  Hello

  My HARD drive died, so I decided to upgrade my Satellite Pro C660 - 1 9 to an SSD.
  I made a USB bootable with Win8 and starts very well.

  The problem is that it does not detect my SSD, so I can proceed with the installation.
  SSD appears in BIOS but not in Windows Installer.
  He said that there is a missing driver.

  I downloaded the AHCI drivers (XP, only ones available) and even in this case, after you have selected the only rider that appears, it says no new device found.

  I tried to change the SATA from AHCI mode to compatibility mode and it's the same thing...

  What can I do?

  Thanks for the help.
  Best regards
  Bruno Moreira

  More old Windows XP need a driver AHCI Intel's but I think this isn't a problem with SATA driver missing because as far as I know Windows 8 as well as Win 8.1 already contains the drivers to recognize the SSD or HARD disk drive.
  In addition, the installation of the OS should be possible even if the driver would be added for this procedure, you must use the "compatibility" mode
  As you say, the compatibility mode is not working too, so I think there is another problem.

  However, page driver Toshiba also provides a driver Intel RST (Intel Rapid Storage Technology) (Windows 8 - updated) you can try to add during the installation of the OS.

  But I m wondering if you would be able to install this Win 8 on common SATA HDD.
  Have you tried to format the SSD using a different computer, then install Win 8?
  Give it a try.

• Satellite A205-S5880 (PSAE3U) downgrade Vista to XP - does not detect HARD drive

  Hi all
  I got this hair loss situation, I had a satellite A205 - S5880 (PSAE3U) and decided to downgrade to XP, I got all ready drivers for XP (I have the EMEA support site and the wireless from a Czech website), I have my windows XP SP2 g CD and I get after loading everything Since the CD that my HD is not detected or not recognized and it tells me to make sure I have connected (I know I do).

  After doing a search of loong on the web, I discovered I have need the drivers (or something like that) to my HD which is a Hitachi HTS542520K9SA00 ATA Device (200 GB, 5400 RPM, SATA). My bios won't let me put my SATA to IDE (or something like that) also to update and nothing, please I need my Windows XP CD to read my HARD drive, and I can take care of the rest (at least I think so, otherwise I'll ask again: D).

  I also found that I can watch my motherboard chipset for motherboard for my HD controller, it ' s (i think) a toshiba ILHAM v1.00 or Intel Crestline - GM GM965.
  Maybe this info also works: Intel ICH8M

  I would totally be apreciate all the help, thanks in advance. I am able to give any other information you want
  in any case here is a summary of my pc with everest
  ================================================== ================================================== ========================
  SUMMARY OF EVEREST
  ================================================== ================================================== ========================
  Computer
  Computer Type ACPI (Mobile) 86 x PC
  Operating system Microsoft Windows Vista Home Premium
  OS Service Pack Service Pack 1
  Internet Explorer 7.0.6001.18000
  DirectX DirectX 10.0
  Computer name USER-PC
  Name of the user
  Domain logon user-PC
  Date / time 2009-05-02 / 21:37

  Motherboard
  CPU type Mobile DualCore Intel Pentium, 1866 MHz (14 x 133)
  Card mother name Toshiba Satellite A205
  Motherboard chipset Intel Crestline - GM GM965
  Memory system 3061 MB (DDR2 - 667 DDR2 SDRAM)
  DIMM1: Micron Tech 16HTF25664HY-667E1 2 GB DDR2 - 667 DDR2 SDRAM (5-5-5-15 @ 333 MHz) (4-4-4-12 @ 266 MHz) (3-3-3-9 @ 200 MHz)
  DIMM3: Hynix HYMP112S64CP6-Y5 1 GB DDR2-667 DDR2 SDRAM (5-5-5-15 @ 333 MHz) (4-4-4-12 @ 266 MHz) (3-3-3-9 @ 200 MHz)
  Type of Phoenix BIOS (15/05/08)

  Display
  Video card Mobile Intel (r) 965 Express Chipset Family (448 MB)
  Video card Mobile Intel (r) 965 Express Chipset Family (448 MB)
  Accelerator 3D Intel GMA X 3100
  Monitor monitor generic PnP [NoDB]

  Multimedia
  Audio adapter Realtek ALC268 @ Intel 82801HBM ICH8M - High Definition Audio Controller

  Storage
  Controller IDE controller Intel(r) ICH8M SATA AHCI - 2829
  Controller IDE Intel(r) ICH8M Ultra ATA Storage Controllers - 2850
  IDE controller Texas Instruments PCIxx12 Integrated FlashMedia Controller
  Storage controller Microsoft iSCSI Initiator
  Hard drive Hitachi HTS542520K9SA00 ATA Device (200 GB, 5400 RPM, SATA)
  Optical drive MAST * a DVD-RAM UJ-850 s ATA Device (DVD + R9: 4 x, DVD - R9:4 x, DVD + RW: 8 x / 8 x, DVD - RW:8 x / 6 x, DVD - RAM: 5 x, DVD - ROM: 8 x, CD:24 x / 16 x / 24 x DVD + RW/DVD-RW/DVD-RAM)
  Hard disks SMART Status OK

  Partitions
  C: (NTFS) 125915 MB (102380 MB free)
  D: (NTFS) 64863 MB (12885 MB free)
  Total size 186,3 (112.6 free go-go)

  Entry
  Standard PS/2 keyboard keyboard
  Alps Pointing-device mouse

  Network
  Main IP 192.168.0.199
  00-1B-9E-FB-8B-DF main MAC address
  Atheros AR5007EG network (192.168.0.199) adapter wireless network card
  Realtek RTL8101E Family PCI - E Fast Ethernet NIC (NDIS 6.0) network card
  TOSHIBA Software Modem modem

  Devices
  Printer Microsoft XPS Document Writer
  Printer send to OneNote 2007
  Controller FireWire Texas Instruments OHCI Compliant IEEE 1394 Host Controller (PHY: TI TSB41AB1/2)
  USB1 Controller Intel 82801HBM ICH8M - USB universal host controller
  USB1 Controller Intel 82801HBM ICH8M - USB universal host controller
  USB1 Controller Intel 82801HBM ICH8M - USB universal host controller
  USB1 Controller Intel 82801HBM ICH8M - USB universal host controller
  USB1 Controller Intel 82801HBM ICH8M - USB universal host controller
  USB2 Controller Intel 82801HBM ICH8M - USB2 Enhanced Host Controller
  USB2 Controller Intel 82801HBM ICH8M - USB2 Enhanced Host Controller
  USB camera Chicony USB 2.0 Camera
  USB device USB Composite device
  Battery Microsoft AC adapt
  Battery Microsoft ACPI battery compatible control method

  DMI
  Provider DMI BIOS TOSHIBA
  DMI BIOS Version V5.60
  TOSHIBA DMI system manufacturer
  DMI system product Satellite A205
  DMI system Version PSAE3U-08C023
  DMI 68221541 K-system serial number
  DMI system UUID EA88852C-3BD111DD-968C001E-EC3CB59A
  DMI Motherboard manufacturer TOSHIBA
  DMI Motherboard product ILHAM
  DMI Motherboard Version 1.00
  DMI Motherboard Serial number 0123456789AB
  TOSHIBA DMI chassis manufacturer
  DMI chassis Version n/a
  DMI chassis serial number, no
  DMI chassis asset tag *.
  DMI chassis Type Notebook

  ================================================== ================================================== ========================

  Hello!

  You will find hundreds of discussions here in the forum about this, if you install Windows XP and Vista from a Microsoft disc and the HARD drive can't be detected... So he s strange to read these questions again and again.

  However, to install Windows, you need the SATA drivers or let's say the Intel Storage Manager package. It contains the driver you need. You can then create a new installation using nLite [www.nliteos.com]
  Or look you at this Toshiba document: http://aps2.toshiba-tro.de/kb0/HTD9401AN0000R01.htm

  Good bye

• Windows 8 Setup does not detect hard drive Vmware

  When installing, it says no hard drive found...

  What can I do about it?

  It's the Windows 8.1...

  Without knowing the configuration of the virtual machine (this is why I asked for the log file) it is difficult to say what is causing the problem and how to solve.

  André

• HP 15-F039WM: could NOT DETECT MY DRIVE SINCE the REFORMAT HP 15-f039wm Windows 7 PRO

  I just recently installed a windows 7 64 bit on my hp 15-F039WM, but I'm having a problem with the driver installation for my laptop can't read my Flash DRIVE, no usb driver is installed. Need your help on how to install the drivers for your laptop.

  Thanks in advance guys

  Have you tried the flash drive in another port? You should have 2 USB 3.0 ports, on one side and a USB 2.0 on the other. The USB 2.0 should work.

• Boot failure: REM could not detect 2 hard drives

  Hello. I bought a HP Pavilion G6 series laptop (LX273EA #ABU) last year and he stopped to load correctly. When I click on "Repair (recommended)" I get an error messaqe saying "REM could not detect 2 hard drives. I tried to start in safe mode and it will not work.

  The laptop is two months out of warranty, and the only support option I found is a phone call from £30 with no guarantee of assistance. Any input would be appreciated.

  Thank you

  Michael McDonald

  You are welcome Michaelmcd85.

  The 305 error indicates that the hard drive has failed. You will need to replace the hard drive.

  This is an easy repair so I'll give you the information you need to fix yourself. It's your interview Guide &. It contains information on how to disassemble the laptop. The guide also contains information that will allow you to choose a replacement hard drive.

  If you do not want to repair the laptop you can contact HP Support directly to the 1-800-4474-6836 if you are in the USA / Canada. If you are in another country, you must first visit HP's Support around the world to find the coordinates for your region.

  I hope this information is useful.

• Satellite P10 304 BIOS does not detect HARD and CDROM drive

  My HDD p10-304 has recently failed.
  I bought a new 60 GB western digital 2.5 drive "and installed today.

  At startup, the BIOS does not detect the drive, but also, it does not detect the CD-ROM drive.
  This makes me think that maybe it's not the player after all, maybe the onboard IDE / motherboard.

  I'm kinda stuck, so it's a new drive should work fine, and I have no way to test the motherboard.

  The only difference is that the insulation on the original drive sleeve should be reduced by half.
  The bit important (low, where the circuits would otherwise affect metal) is always there, it is the
  Few albums I had to remove but that should be no problem.

  Someone at - it suggestions?

  Thank you, Stu.

  Hello

  What happens if the HARD drive is not connected to the motherboard? The BIOS recognize the CD/DVD drive correctly?

  You bought the HARD drive compatible? To my knowledge the Mobile supports a HARD drive with interface IDE (ATA-5) increased.

  But as you said possibly the motherboard failures and he would be advised to contact the technician during a particular test

• Cannot detect hard drive

  Dear Sir.

  I just got this T320 and my problem is now I have no cd, readers, manuals, etc coz they it shipped from China. I tried to follow all of the instructions but cannot find the 2 installed 500HDD (Constellation of Dell).

  Please help me to make the system work.  I tried ATA AHCI RAID and so forth, but could not detect the hard drive.

  Thank you for your support and greetings to all.

  Water

  Hello

  The reason Windows installation doesnot see readers, is that pilots of PERC is not loaded.

  Here's what I suggest:

  (1) you've seen stranger configration in PD MGMT. (something I need to know is, you are about to install a new window, right?) -If so, clear the foreign configuration. Page 44 of the reference: ftp://ftp.dell.com/Manuals/Common/poweredge-rc-h310_User%27s%20Guide_en-us.pdf

  (2) after deleting, move forward and create a RAID. Reference page 41, same link.

  (3) you can proceed to installing windows using some methods. I recommend the Page 8 "Installation of Microsoft Windows Server 2008 R2 using USC"

  FTP://FTP.Dell.com/manuals/all-products/esuprt_electronics/esuprt_software/esuprt_operating_system/Ms-win-Srvr-2008-r2_Reference%20Guide2_en-us.PDF

  Let me know the results.

• HP Pavilion g7-2043sf: Windows could not find a driver for your network card

  Model: HP Pavilion g7-2043sf

  Product number: B1P51EA #ABF

  Today, I did a clean install of Windows 7 on this laptop and I can't connect to internet via wifi. When troubleshooting I get this message:

  Windows could not find a driver for your network card
  Windows does not detect a network card is installed correctly. If you have a network card, drivers for the card cannot be installed correctly.
  Install a driver for your network card
   
  Collection information
  Windows Version: 6.1
  Architecture: amd64
  Time: Thursday, December 24, 2015 12:34:16

  In Control Panel, I found this information:

  Ethernet controller: the drivers for this device are not installed (Code 28)
  Hardware ID
  PCI\VEN_10EC & DEV_8136 & SUBSYS_1844103C & REV_05
  PCI\VEN_10EC & DEV_8136 & SUBSYS_1844103C
  PCI\VEN_10EC & DEV_8136 & CC_020000
  PCI\VEN_10EC & DEV_8136 & CC_0200
  
  Network controller: the drivers for this device are not installed (Code 28)
  Hardware ID
  PCI\VEN_1814 & DEV_539A & SUBSYS_1839103C & REV_00
  PCI\VEN_1814 & DEV_539A & SUBSYS_1839103C
  PCI\VEN_1814 & DEV_539A & CC_028000
  PCI\VEN_1814 & DEV_539A & CC_0280

  I visited this side: http://support.hp.com/us-en/drivers/selfservice/HP-Pavilion-g7-2000-Notebook-PC-series/5226249/model...

  I need all drivers of network?

  Thank you.

  Hello:

  You need these drivers...

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp55979.exe

  This package contains the installation package driver for Ralink Wireless LAN to laptop models controllers that are running a supported operating system.

  File name: sp58586.exe

• BIOS Inspiron 2305 does not detect the drive in ahci mode

  The hard drive in my Inspiron one 2305 crushed and I tried to install a 500 GB Seagate Barracuda drive.

  The Bios does not detect the drive. I noticed that the SATA in the BIOS mode option has been put on AHCI. I changed the ATA mode and the BIOS has detected the drive.

  However when I try to install a clean version of Windows 7 (Dell OEM disc), to halfway to the installation Setup will fail. I noticed that the reason why it will fail, is that the installation process now does not see the hard drive.

  Can someone tell me what steps to take to do the installation?

  theFlash1932 and natacuk4

  Although I was not able to swap the Sata cables as natacuk4 suggested; It looks like just unplug and reinstallation of cables Sata what it did the trick!

  I was able to boot the system several times and it seems that everything works fine.

  Thank you guys for helping me solve this problem!

• "Setup could not detect all the printers.

  I've recently set up a new computer and the network.  The host computer is running Vista.  I have connected a Deskjet 6940 via an ethernet cable into the Linksys router and can print from the host computer.

  I have a laptop which is under XP Pro, and who has a connection with the network.  I downloaded the driver from HP on the laptop to try to connect with the 6940, but during the install process, I get the message "Printer not found - Setup could not detect all the printers on the network."

  Firewalls on both computers is disabled.

  When I type the IP address in the address of the host computer or on the portable bar, I page of the printer, including its SSID.

  I tried to type the IP address in the field suitable for the installation of HP on the portable routine, however and always got the "printer not found."

  Ideas?  TIA

  The Deskjet 6940 being on the network, we will try to add the printer manually. Here is the sequence to XP:

  1. Click on the button 'Start'--> Printers and fax machines.
  2. Under print jobs, click on "Add Printer".
  3. Click 'Next' in the Add Printer Wizard window.
  4. Select " printer local to this computer. Deselect "automatically detect and install my Plug and play printer." Click "next".
  5. Under Select a printer Port option, select "Create a new port" and choose "Standard TCP/IP Port" and click "Next".
  6. In the "Welcome to the Add Standard TCP/IP printer port Wizard" make sure that the printer is turned on and connected to the same network that your computer is connected to. click on the button "next".
  7. Under "Add Standard TCP/IP printer Port", enter the host name of the printer . You can also use the IP address of the printer if it is static. Click 'Next' and then click 'Finish '.
  8. Now, select HP in the manufacturers list, select your printer from the printer model list and click the button "next".
  9. If you can't find your printer, you will need to find the installation CD and use the 'Disc' option to select one of the files hp*.ini. You can also select another model of the same type HP printer.
  10. Add the name of print spooler and click on "next".
  11. Click "next".
  12. Click "Next" and "Finish."

• My MBP is showing a "Remote Disc" in the list of devices. It's not a hard drive.

  My MBP is showing a "Remote Disc" in the list of devices. It's not a hard drive. So where did it come from? I 'get info' on this subject, but it doesn't tell me a thing.  He sees the disk drives elsewhere in my house? It's to see my iPhone as a remote disc? The photo with him is a DVD or CD gold. It drives me crazy.  I am running OSX Sierra.

  This has been on the Mac for a while now... Here is a link that can better describe it.

  Use the CD or DVD drive from another computer with your Mac - Apple Support

• I'm trying to upgrade from windows vista to windows 7 - my western digital not recognized hard driver

  I am trying to upgrade to windows Vista Home Basic to windows 7 ultimate - my western digital not recognized hard driver. When upgrading the hard drive is not in the list of places to install. In addition, the driver is not found.

  Windows Update has nothing to with the upgrade of Windows. Please post future questions about the upgrade in this forum: http://social.answers.microsoft.com/Forums/en-US/w7install/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft