Precision T7600 thermistor

Similar Questions

• The Dell Precision T7600 CPU temperature and fan speed

  Hi all

  I recently got a Dell Precision T7600 workstation that has two processors Xeon E5-2620.  I checked the specifications of Intel and the maximum temperature for these processors apparently is 77.4 C.

  However, when you run fairly intensive applications that can last a few days or so to analyze, I noticed that the CPU temperatures get much hotter than this no difference in the speed of the fan.  I used speedfan and CPUID to check the temperature/fan speed.  The highest I've seen the temperature was 90 c and the fan speed has been only 900 RPM.  He regularly sits on 70 c and still no response from the fans.

  I find this a little hard to believe given that surely fans should be a little lower than 90 c action!  I checked the settings of the bios (version A05) and the fan speed control is on auto.  I have also run the diagnostics and it reported no problem.  The fans run, but I'm not convinced that is the speed controller!

  Is this normal?

  I managed to re - install the A10 bios (it appeared to include a few things my already installed version is not ).

  Anyway, tried to launch a number of things to keep the processor at 100% for a few hours.  It seems that the fan speed changes now and the maximum temperature of the processor, I was able to get (and briefly) was 72 C.  He had served mainly the mid to high 60s with fan speeds ranging between ~ 1000 - 1500 rpm, as required to keep it there.

  I would say that the new BIOS has solved my problem.

• precision t7600 h310 PERC driver

  I'm looking driver for the Perc h310.

  Try to install the Win 7 32-bit operating system, but the installation can not see the hard drive - so I need real driver to go beyond this.

  Are all the driver I downloaded install packages. I need the driver file WIn 7 install it will see the player if the H310 Perc raid controller please.

  The system is under warranty and can not find a chat or telephone number for assistance.

  Note: RAID Setup (pre-installation pilots)

  Table of contents:

  T3600: Windows 7 (64 bit) & Windows 7 (32 bit)

  T5600: Windows 7 (64 bit) & Windows 7 (32 bit)

  T7600: Windows 7 (64 bit) & Windows 7 (32 bit)

• Delays in DAQmxWriteRaw when you use several cards PXI-6733

  Application:
  I have an application that generates and writes the analog data at 300 kHz slightly underneath.  Data generation and output take place every 14 ms (we'll call it who a 'block',) through an event EveryNSamples leave a timing sheet.  In each block, 4000 samples of analog data are generated and output to 6 of the 8 channels of analog output of the PXI-6733.  The output buffer is set to twice the block 4000 writing samples and pre-filled with 4000 zeros, so the output is always a block behind the data generated.  If a single block exceeds 14ms to generate and write on the analog samples, the output buffer will be against the wall and exit stop (regeneration is disabled.)  I recently needed to add more than 10 output channels, so I installed a second PXI-6733 map in the chassis and set up a second analog output task to write the second map.

  Problem:
  As analog data are generated on demand in each block of 14 ms, the program cannot take more than 14ms to generate the data and write them on the cards, otherwise we will underflow analog output.  Thus, any unwanted delay must be avoided.  Data generation stage does not take very long (in my test it is off and decision< 1ms,)="" but="" i'm="" seeing="" some="" problems="" when="" i="" write="" the="" data="" to="" the="" pxi="" cards. ="" i'm="" using="" the="" daqmxwriteraw="" function="" to="" write="" the="" samples="" to="" the="" cards. ="" the="" function="" is="" being="" called="" twice="" every="" update="" loop:="" once="" for="" each="" output="" task="" (card). ="" when="" i="" added="" the="" second="" card,="" i="" noticed="" that="" occasionally="" the="" call="" to="" daqmxwriteraw="" would="" take="" much="" longer="" than="" 14ms,="" causing="" buffer="" underrun="" errors="" (-200016)="" on="" the="" second="" card,="" or="" regeneration="" errors="" (-200290)="" on="" the="" first="" card. ="" i="" inserted="" timing="" markers="" around="" each="" call="" to="" daqmxwriteraw,="" and="" i="" see="" that="" normally="" the="" calls="" each="" take="" around="" 4.8e-5="" seconds="" to="" complete="" on="" card="" 1="" (whether="" alone="" or="" in="" conjunction="" with="" card="" 2). ="" on="" card="" 2,="" the="" calls="" take="" usually="" take="" about="" 4.8e-5="" seconds="" to="" complete,="" but="" they="" occasionally="" spike="" to="" between="" 5="" and="" 40ms="" (e.g.="" 6="" out="" of="" 300="">

  I wonder what would cause these erratic spikes in time it takes to DAQmxWriteRaw BIE called on the second card.  Is there a known issue with the help of 2 PXI - 6733 s in the same PXI chassis?  Could there be some sort of conflict of resources (not enough channels DMA, etc?)  The two report cards they have in DMA mode, and fill FIFO priority is set to NotEmpty.  The problem also occurs when the transfer mechanism is set to interruptions.

  Other Observations:
  I noticed the first edge of calendar corresponds to the point in the program to the location of loading the dll "nicesru.dll."  I can't find any information that features in this dll, and I don't know if it's a symptom or a cause.

  I also noticed that when an error occurs, I can't seem to stop and clear the tasks of production.  After trying to stop it and cancel all active jobs, keeps blinking the link on the PXI chassis light.  To reset, the only way is to go into solution of measurement and Automation Explorer and reset the second card 6733 manually (or use ResetDevice C calling).  There seems to be only the second PXI-6733, and it also happens when using the test panels in the MAX program.

  Material:
  PXI chassis, 1033
  1 x card synchronization PXI-6608
  2 PXI-6733 analog output cards x
  1 x card PXI-8461 CAN
  PXI, PCIe - 8361 I / map F

  Dell Precision T7600
  E5-2687W CPU Xeon

  Software:
  Windows XP SP3 32-bit
  NOR-DAQmx 9.0.2
  Visual Studio 2008 sp1

  I was able to solve the problem by moving the PCIe card in the PC to another location.  I assumed the problem was with how bus PCIe are managed by the motherboard, or how the resources have been allocated to the cards in this particular niche.  Move the map on the slot 16 second x on the motherboard seems to have solved my schedule delays.

• Computer workstation to PTC Creo 3.0

  Hello

  I want to upgrade my workstation for work recently. My current computer is workstation Dell Precision T7600. Here are the specs below;

  • CPU - Intel Xeon E5-2687W x 2
  • RAM - 16G
  • VGA - NVIDIA Quadro 40000
  • SSD - 256

  I'm looking for the faster dual processor (motherboard) and CAD (latest version) video card, faster memory, and SSD on an empty stomach. The CAD software we use is TPC Core 3.0 and would need a certified partner of video card. You are able to indicate an overall increase in the percentage of performance? Current speed percentage (3.1 GHz) processor increase in performance.

  Thank you

  Hi Yslum830,

  Thanks for your post.

  I'm sure others will be happy to give their opinion here, but your business must have a designated representative.  They would be the best source for the answers you seek, then have you consulted with your representative yet?

  Kind regards
  Robert

• H310 Raid 1 question

  Hi all

  I have the following, not sure is the raid H310 card tells me the drive is bad or what.  One place in the Raid BIOS it says reader: 00 is missing or foreign and other place reports 00:rebuild.  It is not what I can see, reconstruction was like that for days.

  Think, you get a new disk and type in there?

  Here is the info of different tabs in the bios raid H310.

  Dell Precision T7600
  RAID card H310 - RAID 1

  VD Mgmt
  ID:0 VDISK Large Raid 1862,50 GB

  Physical disk
  Lack of
  : 01: online: 1862,50 GB

  PD Mgmt
  00 foreign 1862,50 GB SATA
  01 SATA 1862,50 GB Online

  Outside view
  Disk 0, Raid 1 (partial foreign) group

  Virtual disk
  ID:0, Big Disk, 1862,50 GB

  Physical disk
  00:rebuild: 1862,50 GB
  01: online: 1862,50 GB

  Thank you

  Joe

  Buy a LABELER and label each disk cable and your data.  Then remove the drives.

  Buy 2 NEW READERS INSTALL AND INITIALIZE THEM.

  Then replace the old disk 1 and see if it will rebuild.

  You can't rebuild on a raw disk, it needs to be initialized and ready to rebuild.

  You get two discs, so you do not accidentally initialize icon who still has data.

  RAID 1 is an exact copy (or mirror) of a set of data onto two disks or more; a classic RAID 1 mirrored pair contains two discs.

  RAID 0 is scratched.  If you lose ANY player you write all data.

• I need two part number in 3020 OptiPlex Mini Tower

  

  The switch and the speaker can help me?  @SpeedStep

  The part number for the intrusion switch is on the white label, you can see on the photo.

  The part number for the company premises will be a white label on the side of the enclosure also.  Internal speaker Assembly 29MKK

  029MKK Optiplex 390 790 990 3010 internal 23mm speaker

  OptiPlex 390 3010 MT Mini-Tower switch button 74XPK

  Dell UC635 chassis switch

  Compatible models: 3010 OptiPlex, OptiPlex 740, desktop OptiPlex 740, OptiPlex 360 Minitour OptiPlex 740, OptiPlex 740 MLK, 740e OptiPlex, OptiPlex 745, OptiPlex 745 Desktop, OptiPlex 745c, 745th OptiPlex, OptiPlex 755, OptiPlex 990, OptiPlex GX520, OptiPlex GX620, OptiPlex XE, Precision T1600, Precision T1650, Precision T3600, Precision T5600, Precision T7500, Precision T7600, Precision T7600, T7600 WORKSTATION workstation

  

  

• Output H.264 fails in After Effects and SOUL

  I'm having the same problem - export H.264 crashes into the 01:03 score every time. DNxHD is very good.

  Dragging comps to Adobe Media Encoder and trying to make there do not work either.

  My installation of CS6 [last week] is done on a computer nine to eight double heart Dell Precision T7600 with Windows 7.

  It is ridiculous to say that we should not make H.264 on After Effects. Sometimes I return 50 + TV commercials at models of composition for the delivery of a multitude of media - each with slightly different characteristics.

  Even if the SOUL is a workaround, dragging all these comps on a crippling waste of time.

  It is a problem with Adobe, and we've all lost too much troubleshooting time and talk about it. PLEASE CORRECT.

  Thank you.

  There is a bug in the Apple for QuickTime H.264 encoder.

  If you want to avoid the bug, the best thing to do is not to use Apple's H.264 encoder.

  When you encode a movie .mp4 in the SOUL, he does not use Apple's H.264 encoder. When you encode a file with H.264 .mov, it uses Apple encoder.

• Reference Dell perc h800

  Hello everyone we recently bought dell precision t7600 and perc h800 map for

  control of Keystone md 1200 powe... Win server 2008 r2 is installed but no driver work for dell perc h800 tried so site Web of frim dell drivers but still no hope... am wondring if anyone can help me... Thank you

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/PowerEdge-T710?driverId=W7X7H&osCode=WS8R2&FILEID=3176115748&LanguageCode=en&CategoryID=SF

  Since you're under 2008 R2, you might be able to run the Package version of update for Microsoft Windows, but since 2008 R2 is not supported on the T7600, it may not work properly, then you can try the hard drive version.  Since the H800 is not supported on the T7600 at all, it is possible that none of the Dell drivers will work.

• T7600 PSU Precision fans occasionally runs at full speed for no reason

  Having a strange problem with my T7600 - no reason that I can see the power supply fans will ramp (for the period of approximately one minute) at full power and stay there, regardless of the load of the processor and the environmental conditions. My only options are to reboot the machine or wait (sometimes up to half an hour) for them to get by, and then they recede down to their silent whisper normal levels. The noise is unbearable and can easily be heard a few rooms away.

  Is this something that can be fixed in firmware or make me a defective unit?

  For some time now since the last incident with fans of PSU works 100%. It seems to have fixed itself, which hurts me a little uncomfortable because there was no action on my part that solved...

• About precision (NI 9216 &amp; NI 9217)

  Gurus,

  I'll have a test machine custom built by an outside company that is to include a cRIO OR with a few different DAQ modules; including 9216 NI and NI 9217 RTD modules. Our requirements of uncertainty (accuracy) for measurements of air temperature and liquid (RTD) are and 0.15 ° C 0.2 ° C, respectively. After looking at the technical details of these modules, I'm afraid they will show the temperature of 0.15 ° C justesses for the single module (4-wire mode). This seems to leave no room for uncertainty of RTD himself. I guess we have to take into account the error of stacking between the sensor itself and the data acquisition module. I am wrong in my reasoning, is there a DAQ card more specifies who may be specified, or are we simply not be able to meet the requirement of precision specified? Thanks in advance for any idea that you all have.

  Hello ckc8302,

  Thanks for posting your question because it always a good idea to ask and make sure that the devices meet the specifications.

  Looking through the sheets of these two devices, it seems that the modules themselves will not be able to meet your specifications.

  NEITHER 9216 Factsheet - http://www.ni.com/pdf/manuals/376921c_02.pdf

  NEITHER 9217 Factsheet - http://www.ni.com/pdf/manuals/374187a_02.pdf

  In addition, I already tried searching throug our other c series modules and other materials listed in section below.

  Choose an RTD or thermistor measurement system - http://www.ni.com/white-paper/3643/en/

  The article also lists the 9226 and the 9219, but the two still do not seem to meet him your spec.

  It seems that the only capable card would be NEITHER SMU-4357, but at this point, you may need to revise your system configuration.

  Datasheet of NI SMU-4357 - http://www.ni.com/datasheet/pdf/en/ds-413

  I hope this information was useful!

• x 8 connection distance MXI causes conflicts with my on my Dell Precision T3600 PCI slot

  Hi all

  The easiest to say is that I am migrating from a x 4 MXI explicit connection to an x 8 MXI express connection and when I do I get an error on the motherboard which is unable to load the single PCI slot.

  Error in WIn7 64 bit Device Manager reports a yellow exclamation point

  Device "Intel (r) 82801 PCI Bridge - 244 properties"

  The error listed in the device status box: "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Unfortunately, I need this slot machine to run a card calendar to conjucton with PXI hardware. There is no anomaly when I used the x 4 connections with virtually the same loadout except for one Exchange a PXI-5122 (x 4 config) to SMU 5122 (x 8 config).

  If I leave the MXI PCIe card in but do not connect to chassis PCI slot SMU (and the fine card appear.)

  If I remove the PCI card into the slot, the error still occurs.

  I swapped the x 8 card and NVidia graphics card without success (the 16 x only two slots).

  I photographed the reader and removed the H310 Dell PERC RAID card and charged the RAID array RAID integrated Intel C600 and still no change.

  I have updated BIOS to A07 to latest A08.

  I updated the Intel Chipset at the latest on the Dell Web site.

  I guess that I just wonder at this point if someone is able to run a x 8 MXI express at SMU with a Dell Precision T3600, T5600 or a T7600 chassis.

  PC - Dell Precision T3600

  Windows 7 Enterprise 64-bit SP1

  3.2 GHz Xeon 6 core (E5-1650) w 16 GB of DDR3 memory

  Reference Dell PERC Raid (x 8 PCIe) H310 / C600 onboard Intel RAID

  Nidia Quadro 600

  2 x 1 TB SATA drive (mirrored)

  SMU Rack - OR 1082

  Slot 1 - SMU - 8381

  Slot 2 - OR SMU 5122

  Slot 3 - NOR SMU 5442

  Housing 4 - OR 4 to 6 TB RAID NI 8262 x MXIe

  Housing 5 - PXI 6733

  Housing 6 - PXI 6733

  NI MAX report is attached as a text file.

  After much work by NI Applications Engineer Kyle K, this problem has been resolved.

  I'll post the solution to this PC dependent problem here, just in case it will help others in a similar situation.

  It seems that Dell sometimes uses one default BIOS quite restrictive on the number of PCI bus in these (and other). By allowing several PCI bus, you will be able to list all the devices in the sacrifice of some memory available for OS 32 bit running on 4 GB of RAM. No problem for me because I'm under 64 bit OS.

  Congratulations to Kyle even if he has not posted here yet for him give real congratulations.

  Greg

• measures of thermistor using modules SCXI-1102 and SCXI-1303

  Hello

  I have a 1303 SCXI front-end module connected to an SCXI-1102 module

  I read the article detailing how to remove bias and pullup resistors to activate measures of RTD/thermistor on the 1303. What did not mention article was the case plug the excitation source, and what is the best source of operating voltage (normal etc., high precision)

  I was wondering where I can find this information, also, I could do several types of measure on the same 1303? I have an analog voltage to a flow meter, and I would like to put it on the same module as the Thermistors

  Thank you!

  Kevin

  Kevin,

  The pulling up of resistors to connect to + 5 V internally.  If the values are not suitable for your application, you can use those.  It does give you much flexibility but.  The 1303 does not give you any other access to any source of current or voltage through screw terminals.

  Pull upward and pull down resistors are networks of resistors Series 9-pin SIP. So you can edit them in blocks of 8 channels for joint measures.

  Lynn

• excitement of the thermistor and NI6224 DAQ board / whatever it is quick and (relatively) cheap?

  Hello world

  I need to measure temperatures between 15 ° C to 40 ° C and to resolve precisely the changes in 0.1 ° C. My thermistor has a nominal resistance of 22 kOhm at 25 ° C and the resistance of 14 KOhm at 37 ° C. constant dissipation in air at 25 ° C is 0.3 MW / ° C - but the thermistor will be used in aqueous solution. I have a NI6224 DAQ card with a connector in SCB-68 and Labview 7.

  How do my NI6224 work with my thermistor with minimal cost?

  In particular:

  the NI6224 has no analog output. Can I use a digital output as a power source? I would say no because the current digital output is 24 mA, it would make my time 14 KOhm > 10 V, which is the input of the Board of Directors range 24. Is this correct?

  I could buy a module NI 9265 + chassis + cables etc to provide the excitation of the thermistor current and connect his two sons to a Council NI6224 differential voltage input? Y at - it any cheaper option with others OR or equipment of third parties?

  Thank you in advance for your time and help

  (Note that this message was posted in response to another thread named "thermistor". I'm following the suggestion to move here in a new thread to increase visibility and try and get help...)

  Yes.

  You are correct about both measures ended up alone. The other end of the probe will be connected to the Earth.

  There is no advantage to a measure differential in this situation because there is no true differential signal.  The two voltages are referenced to ground.

  Calibration is always a good idea. Here, he will compensate for differences of Thermistors and fixed any deviation from the nominal value of the resistance.

  Even if your temperature is probably change very slowly, it can be useful to sample at a rate groups and average high of samples to produce a single reading. This can considerably reduce the noise. A common source of noise is the electric current. By sampling at a multiple of the line frequency of power, such as 1200 Hz and then with an average of 1200 samples, you get a reading per second with substantial reduction in 50 or 60 Hz noise.

  Lynn

• Workstation T7600 die lenta

  avevo gia reported it all problema'assistenza tecnica just not it computer e stato da e dopo svariati test, mi fu detto che he pc non aveva problemi.

  Siamo Fanta avanti bass comunque di una ws di lavoro che può non fairs is fermi macchina o nobodies. A giugno luglio di questo anno e stato made con successo aggiornamento Windows 10, song che con it nuovo SO qualcosa migliorasse. Pochi giorni fa e stata acquistata una nuova ws di fascia inferiore (precisely the T5810) e questa "viaggia" di gran lunga a Velocità nettamente superiori. Premetto che, quando acquistammo T7600 questa gamma of era it di top Dell, con 16 GB Ram e di due da HD Sata 500 GB, controller Perc H310 III.

  Da sempre T7600 anche quando if starts, e molto lenta, anzi her barra di avanzamento che compare al post logo it sotto Dell, fino arrived a circa it 50% PVE if closed by diversi secondi (forse anche a UNAMET) per poi riprendere ed reach fino alla fine. Da reference tests con su internet utility found i results sono inferiori nettamente has quanto Google esserlo quelli riferiti al pc stesso.

  NB: e stato sostituito Reed it primo con HD SSD Samsung 850 Pro, qualcosa e great improved my come not here if aspettava.

  Buongiorno,

  questo Forum e enjoy a sistemi company.

  By su sistemi client is, the invito a tramite contattarci twitter twitter.com/DellAiutaPRO @DellAiutaPRO