Presentation of Cisco C40

Similar Questions

• Cisco C40 unsubscribe automatically with CUCM 8.6.2

  Hello

  I have Cisco C40 connected to CUCM 8.6.2.

  First, he is registered with CUCM and I was able to call on another phone C40.

  Then, C40 automatically BSW of CUCM and isn't recording with CUCM now.

  I added C40 via device-> phone-> Add new-> then selected Teleprecense C40

  C40 SW version is: 5.1.5.297625

  I joined C40 and CUCM screenshot. It shows not recorded, which proves C40 registerd at least once.

  I could make and receive calls with the C40 for a few minutes. Subsequently recorded automatically and now

  error message is status: failed

  Suggest pls.

  Rgds

  Rajesh

  Hi Renon,

  Please below changes made in the SIP settings:

  change SIP profile 1 Type at Cisco, since it is native enrolled and default transport for TCP

  * c xConfiguration SIP URI 1 profile: "[email protected] / * / "

  "

  * c xConfiguration SIP profile 1 DisplayName:

  * c xConfiguration SIP DefaultTransport 1 profile: TCP

  * c xConfiguration SIP profile 1 TlsVerify: Off

  * c xConfiguration SIP profile Type 1: Cisco

  * c xConfiguration SIP profile 1 outgoing: Off

  * c xConfiguration SIP profile 1 Proxy Discovery 1: manual

  * c xConfiguration SIP Proxy 1 address of profile 1: "172.31.131.10."

  * c xConfiguration SIP profile 1 Proxy Discovery 2: manual

  * c xConfiguration SIP Proxy 2 address of profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 3: manual

  * c xConfiguration SIP Proxy 3 address profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 4: manual

  * c xConfiguration SIP Proxy 4 address of profile 1:

  * c xConfiguration SIP profile 1 1 LoginName authentication:

  * c xConfiguration SIP profile 1 1 password:

• Disable the message/call Cisco C40 failed alert

  Hello

  We have an installer of the C40 codec with control system. The touch screen has very limited control over the video-conference system, so not able to reject the "missed calls" message or alert that appear on the screen.

  The missed call alert appears permanently on the screen, even after you have launched another call. Is there a command API or how to turn off the prompt to alert/message missed calls?

  We cannot disable the OSD. It is one of the requirements.

  Hello

  In the next version of TC6, there will be a command that will disable the notification shown on the OSD display (if you do not use the key).

  xConfiguration video OSD MissedCallsNotification:

• C40 Cisco does not go on standby mode

  Hello

  I have a problem with a Cisco C40 where the codec simply is not going to go into sleep mode. I tried every possible thing to make it work, but without success. When I use Putty and you connect to it and sent the normal control: xcommand Eve turn on it goes to sleep. I also did a system reset, without success.

  When using the graphical interface and tell the system to go into mode after 1 minute, the system will remain forever.

  Anyone else having this problem, I have a second Cisco C40 who started doing this morning so I'm not sure what to do. I also noticed that the codec comes out of sleepmode the source presentation will change also to the main camera.

  Kind regards

  Cornelis Stoop

  The problem may be caused (in the screenshot eln_1.png) to have the Source of presentation to the source of the main camera.  This must be set on an other sources and not the main camera.

  Able to provide the whole xconfig one of the devices having the question rather than just two screenshots of the web interface, which do not show everything?

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Cisco Codec C40 remove wallpaper

  Hi all.

  In our installation of cisco telepresence, that we met an interesting question:

  the cisco c40 codec admin created a custom wallpaper, somehow this wallpaper was not appropriate for this codec for 100%.

  After that he transferred the wallpaper on the unit - it restarts. We see a cyclical reboot - boots of unity, we see a cisco logo, then we see a (part of the GUI) overlay on the monitor, after this codec is trying to load wallpaper, fails and went into reboot.

  Are there ways to manually remove this wallpaper of the codec s flash without hard resetting the codec?

  Hi Eugene,

  Try to login as an administrator using ssh/console and run the following command:

  xConfiguration video wallpaper: Summersky

  Best regards

  Sergey Kuzmin

• Update codec C20/C40 cisco to 6.1.2 meetings lost contact with cisco

  So I improved a few Cisco C40 codec C20 5.1.6 to 6.1.2 the process was smooth.   He updated the device of the codec and cameras, but once the upgrade has completed, the touch screen of cisco lost all meetings.  Is there a way to put all meetings (from outlook calendars) of cisco press?

  A mixture of CUCM and TMS is not really possible.

  In any case, which concerned the TMS, can you set a password for the admin on the endpoint and then add this

  password under the connection tab in the Navigator system of this endpoint.

  After that do a force refresh and apply management settings and see if the meetings will appear again.

  As TMS pushes this information, it would be the correct symptom do not show this info when

  There is a communication / authentication problem.

• C40 Camera control maximum length of cable RJ45 to d - SUB

  Hello

  What is the maximum cable length for the control of camera on a Cisco C40 port?

  Thank you

  Kyle

  According to the PrecisionHDMC camera Guide, page 17, the camera cables that usually come with codecs can be 5, 6.5, or up to 20 meters.  Anything more than 5 meters requires the camera powered by the power of the camera and not the codec using the camera control cable itself.

  I have a few installs custom where the camera control cable is well up to 75-100 feet.  Just follow the outputs pins on the same page as above to make your own cable and don't forget to use the POWER-CAM-V = power supply to power the device.

• With the Canon cameras and embedded image C40

  Hi all

  I got a Cisco C40. We have two cameras Canon XA25 already in place (for a different application).

  Ideally, we would use the guns. Separate us and stream video to the guns to goto C40. Can we push the two cameras of the whole (at the other end)? So that the main camera to feed with a secondary camera to power on this subject?

  Faraz.

  As Patrick said, the C40 does not support showing two cameras at the same time.  The functionality of "Composer" who can do is available on larger end C60, C90 or SX80 points, but not the baby end points.  The provisions on greater endpoints and can be manipulated with the software to the Console of TC .

  But, for your solution, you can feed two outdoor cameras on an external device of picture-in-picture, then just feed one "camera" food to the endpoint.  We do this for many years with various devices in a number of our rooms and on several mobile camera VC carts, back in the old days with old devices analog 4:3 (Kramer PIP-200XL) and, more recently, with lots of cameras HD and PiP (Extron DVS 605).

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Problems during the upgrade to TC7.3.6

  Hello

  A few questions, that I discovered when TC7.3.6

  When upgrading my SX80 Cisco to the latest version of audio software cross somehow does not work. We have the training room with AMX installed control where we have two option either just in presentation mode (without using the VC) or mode video conference.

  The audio from the Chooser of Kramer turns to the codec and then out to the BSS: Blu-102, then to the amplifier. After the upgrade when you do a normal presentation and audio does not work in video mode Audio conference seems to work very well using the same way.

  Decommissioning at TC7.3.5 the problem has been resolved.

  I have a second bathroom with a Cisco C40 where we have installed to switch who has one in and 3 out to our projector and 2 LCD screens. When you use the most recent software two LCDs receives a signal from the codec. I also noticed that everything is pixelated and the edges of even the font on the menu are not readable.

  Decommissioning at TC7.3.5 the problem has been resolved.

  I'll do some additional tests to confirm this problem occurs when upgrading to the latest version of the software until I opened a case of TAC. I couldn't do troubleshooting because these rooms are Executive rooms and I had to solve the problem as soon as possible.

  Everyone has experienced a similar problem?

  TC7.3.6 and CE8 have an additional configuration for the Audio element that connects the audio input to a video entry in the web interface, System Configuration > Audio > input > VideoAssociation 1 line.  More than this, there is a MuteOnInactiveVideo that will cut the line when the video source that is associated with the previous command is not present.

  You can try changing the Mute OFF setting or changing the source of videoinputsource to a source which is where your video source that is linked to the audio source is connected.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Creating Firesight IPS policies

  I need help for creating rule asa firesight ips.

  By default, it is a 'discovery network' under access control. It works fine, I see connection events.

  Now, I want to do full-fledged IPS. How do I do that?

  On Firesight, IPS-> policy, create a new policy, I'm doing here had to be defined, rules and categories?

  Please see the presentation of Cisco Live session BRKSEC-2018 of Cisco Live WE earlier this year. It is a free download from ciscolive365.com.

  He did a great job to specify what policies are necessary for effective deployment of firepower and how to create them.

• Best practices for the implementation of the power of fire

  I am looking for a best practices deployment FireSight? Can someone help me?

  Thank you

  -mikgruff

  There is not a general guide outside the configuration guide of product on the support page.

  Partners have access to a guide designed for deployments of the value which is fairly comprehensive, but that is not published publicly.

  There are some useful tips on recent presentations from Cisco Live in this area, but they are more PowerPoint as the deployment guide.

• Presentation of defult on a c40

  I have a c40 tc 6.1.1 running with 2 cameras connected to it it works fine when I use the remote with the device but when I connect cisco touchscreen and try to present the pc he camera of things like the defult presentation sourse. the web interface says that 3 imput is chosen as the defult presentatin sorce. and even though I have change the camera will always be the presentation sorce defult

  Hi Peter,.

  Please share newspapers Xconfig video codec.

  This will give more details.

  As at present the default source selection goes on camera 2 rather than the PC.

  If you take your camera to the codec it still switches to the camera with a picture in black (as the camera not connected)

  Waiting for answer

  Thank you

  Ravi Kr.

• Backup of configuration Cisco Codec C40

  Dear all,

  Can I know how to take backup of the configuration of the Cisco Codec C40, please?

  And also help me with the document of the administrator?

  Thanks in advance

  Kind regards

  Syed

  You can simply copy the output of the xConfiguration and paste it into the SSH client.  You may need to change the output a bit to get the correct formatting, however.  For example, the output registered since my SHH client contains a preceding * c which must be removed before that I can stick again in the SSH client:

  *c xConfiguration Video Wallpaper: Waves

  When you perform a software update, codec configuration, including the keys installed option is not affected and will remain in the process. Keys options include Premium (PR), double (DD) display resolution and Multisite (MS). C40 has been end of sales since June 2015, so it is not possible to order anything for this, see eos-eol-notice-c51-733467. Procedure to upgrade the software codec is on pg 28, the same page mentioned in my previous answer. To upgrade codec software, you will need a release key when switching from one major version to another, as TC5 to TC7. You can request a release of the Cisco Licensing Portal key > obtain other Licenses > telepresence free software key, as long as the device has an active support contract. If you do not have an active support contract, you can contact TAC and get the free unlock key by referencing the Security Advisory cisco-sa-20160504-tpxml, which you can get a key to unlocking TC7.

• Cisco series C Top Bar top in presentation Mode

  In presentation Mode, the C Series codec displays an overlay of bar status (IP address, Cisco logo, time etc..).

  Unfortunately, this can be a source of distraction or worse, can cover the parts of the presentation to the local public.

  Is it possible to remove this bar?

  Eric,

  This has been fixed in a later version of TC5.x, see below for more details.

  CSCtx15428 : bar the top is always visible, even in full screen and in calls

  Symptom:
  Banner with Cisco logo and clock widget appears on the display when in a call.
  Conditions:
  Running TC software before TC 5.0 and a connected over HDMI device loses connection and is re-connected.
  Workaround solution:
  Perform a reset of the device factory.
  Alternative procedure via GUI:
  (1) connect to the web interface of the codec.
  2) go to Advanced Configuration > output > HDMI > OverscanLevel
  (3) change the overscanlevel to high and save. The video will be reduced to the
  middle of the screen.
  (4) change the overscanlevel to zero, as it was before and save. The video will be
  return to normal.
  Widgets and Cisco header should be gone.

• Mounting ears for a Cisco/Tandberg C40

  I've been going around in circles now for weeks.  Anyone where I can retrieve a set of ears for a Cisco/Tandberg C40 system rack?

  I have a lot here that will not be used, which you can have for free. PM me with details.

  

  /Jens