Print cartridge access cover broke in J6480

Similar Questions

• J5780 "open door. Close print cartridge access door. »

  I just installed a new HP 74 cartridge in my J5780 AIR. Orange flashes and the message 'close the door. Close print cartridge access door"keep scrolling in the message window. I can't find such door. When I close the half top of the machine, the amber light continues to blink and the error message continues to scroll. Help, please!

  This document open door message can help:

  http://support.HP.com/us-en/document/c01050739

• Error message = close print cartridge access door

  I've set up my new 4500 series printer and I can't get rid of this error message.  I tried all the steps listed on the HP support site, but no help.  I can't print at all.

  There is a document with the steps to solve a door open error. This document can be found here. You say that you did all the steps on the HP support site, but make sure that no steps have been omitted in the document.

  If the error persists, then try to perform a hard reset.

  Hard Reset:
  Unplug the unit when turned on
  Disconnect the other end of the power cord from the wall jack directly
  * Wait 30 seconds
  * Connect the device upwards.

  If the error persists, then try a partial reset. This reset path can be found in the document located here. The 4500 is not listed, but the reset is the same as the Group of the top in the document (method 3 and #).

  If this error continues to display after all these steps, then I recommend to contact HP Technical Support on this printer. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  HP Technical Support call case form:
  https://h10025.www1.HP.com/ewfrf/wc/phoneInput?cc=us&DLC=en&LC=en&product=5061082

• Deskjet 6988 print cartridge 'door' - cannot access ink cartridges

  This printer has been giving me excellent service for many years, so I'm not surprised that he can do a little wonky. Yet, any advice would be most appreciated!

  Recently, this "door" has popped up, preventing me access to print cartridges:

  

  It seems to say "turn the printer off," or perhaps "turn off and on again," that would be logical, as requiring to do her little dance and restarts. MOST of the time, it does no good. The cartridges just sitting there, and the door rest.

  However sometimes turning market causes a mechanism to move, and the door up and down and sometimes stays down.

  I saw no references to this 'gate' in the manual. Anyone know what it's called?

  Is there a way to force the printer to zero and drop the door? A factory reset did not work.

  Thank you!

  This fixed/figured it out!

  Remove the Panel on the right side of the printer. It's like two hooks on the top and two clips on the bottom. Gently pull down to unclip. Upwards, you will see the mechanism that connects the cover to a switch. For me, the wire time the "capture" disengaged, and I need to restore the link so that it is engaged when the lid rises or falls. After that I did, the cartridges behaved normally, and the mysterious "door" is never in the way.

• New HP Photosmart 7520 e-all-in-one printer from the box, removed the tape and cartridge access

  

  I have a new HP Photosmart 7520 e-all-in-one printer just out the box. I removed the tape and cartridge access door does not open more than 40 degrees. The figure represents about 80 degrees. I'm afraid to force it. I can't put new cartridges in the printer. Very frustrated trying to get help. It doesn't seem to be a phone number or Web site for direct assistance. HP has really gone down hill. Help!

  Hello

  Mine is about 45 degrees, sufficient space to install the ink cartridges.

  Kind regards.

• HP Deskjet 3522 - cannot close the cartridge access door

  HP Deskjet 3522.  A open the cartridge access door to remove the paper jam.  Door will not go all the way down.  "Hook tab" on the side right will not lower or allow cover for rear seats in place.  Any ideas?  Thank you.

  Fixed it myself.  Fired manually capture tab right side out enough back pin on the cover and push down on the cover.  Nothing broken and the printer works.

• pc2510 check right printer cartridge/no taken into charge/hourglass errors

  Hello!

  If anyone has had success resolving these errors, please let me know, even if it is intended to replace your ink cartridge. Thank you!

  Error description:

  Original problem: printer cartridge "Check right printer cartridge" error message blocks any use of the psc 2510, including analysis and noncopying functions not printable.

  Current issue: hourglass gel accompanied by sounds (alignment?) printer that stops, but message screen ahead never past hourglass...

  Summary of troubleshooting:

  I got an error saying: check the cartridge in the right store. Tried cleaning the contacts on the cartridge and printer with distilled water. When using tactics in the online tutorial, I tried unplugging the power while the printer is open. Since then, just going through hourglass and his printer, it does not advance beyond this icon screen.

  Technical customer support:

  Suggested a semi reset of # and 6 keys more disconnect and reconnect or try the new print cartridge. When asked is there something I could try before buy a new cartridge, suggested I unplug and hold button power for 10 seconds, then reconnect. (Full description of these stockings). For further research, the representative suggested an upgrade.

  Hourglass fix employed attempts of the forums:

  Tried to plug into the wall Strip vs. (Fully plugged loose connection to the brick when notice was not in all the way.) Reset the modem. No results.

  What I have tried:

  Haven't tried a new cartridge in the printer until you have exhausted all non-monetary fixes.

  Full description of troubleshooting:

  The first error: check the cartridge in the right store occurred all of a sudden after use without problem.

  The contacts on the black cartridge have been cleaned, but the error persists.

  After cutting the use for awhile, I reconnected him last night to resolve the error on the current Mac computer printer cartridge. Installation was completed successfully.

  The same error once the installation program completed.

  I performed the following:
  (1) cleaned the contacts on cartridge black print using distilled water.
  (2) disconnected the power cord (by post in the forum)
  (3) disconnected power cord and tried pressing Cancel/left arrow (by the same post in the forum)
  (4) contacts cleaned behind black printer cartridge
  (5) print cartridge black removed, closed insert machine and got error black cartridge (attempt to determine what cartridge was the problem)
  (6) even if this message appears to indicate that the black cartridge was the problem (by the article of the web support) I cleaned the contacts on and behind the cartridge color as well.

  As part of troubleshooting, I had a second error: "Print cartridge in the right store not supported."

  I noticed that the adjustment is more flexible than in the color cartridge. I inspected the box spring and cartridge for damage and found nothing. Clean the dirt, however below the contacts on the machine.

  Also, at some point during troubleshooting, I could access the menu scan but then he quickly returned to the first error message.

  (7) for each article in general support online, I tried to unplug the power, while the cover is open (as shown during the cleaning of the cartridges). This information was not in the manual that came with my camera. I was hoping that this could restore the things.

  Then I got the third mistake: a period of sounds of the printer (alignment?) followed by hourglass on the screen.

  The 2510 seems to be frozen. No buttons like cancel or menu or the button caused no response.

  I unplugged it again (this time with the lid closed) and got the same series. A period of sounds like alignment, then a stop of sounds with the hourglass stays on the screen.

  Customer Service Rep sent the following:

  E-mail 1:

  1. If the printer is on, without turning it off, unplug the power cable of this one.

  2 hold down the # and 6 set, while you hold them, plug the power cord into the printer

  3 hold the keys for about 30 seconds, then the printer tries to turn on, then release the buttons.

  4. If the printer turns off, use on the power button on the printer and follow the instructions on the screen.

  If she always comes with the same error, I ask you to try with a new black cartridge back to us with the results.

  E-mail 2:

  1. when the printer is turned on, without turning off the printer, unplug the cable it

  2. press and hold the button for 10 seconds and release it.

  3. after 1 minute, plug back power cord and try to turn on/off the unit.

  The reason why I suggested to try with a new cartridge is every time that powers printer on, he made a self-test to make sure that all hardware components that work very well, including cartridges. So if there is an error with the cartridge, the printer might freeze if it is unable to determine the cause of the problem or of the point of failure.

  E-mail 3:

  I did some research and the issue seems more likely with the hardware of the printer. [...]

  If the problem persists, get back to us with the information below for the upgrade for your printer options.

  Forums:

  Then I tried unplugging power strip to wall socket and the modem reset without result. Blue light for wireless connection is no longer on.

  Message edited by allinfun2510 on 04/05/2009 17:46

  We discovered the printer from my husband uses the same cartridges (this is also a hp) and so we have put a new cartridge in my all-in-one and it worked. It my case the error was really indicating that I have just needed to replace the cartridges (they were probably too weak or ink)

• OfficeJet 7610: 7610 print cartridge cannot move

  I've changed a yellow cartridge & start printing several days ago. Work today & I get the error message in the thematic section. There are no jams & the print cartridge is stuck behind the shield with no way to access it. How to fix?

  In fact, after having lost a lot of time, including the creation of this account, I had a flashlight and stuck my head in there so I can get a decent view of the little slot on the right side of the cartridge pool area. I found that the reason why the cartridge wouldn't (couldn't) move is that the yellow ink cartridge had spontaneously jumped out of his seat and was blocking the whole mechanism of movement. I slipped a yellow cartridge a little table in the slot and pushed back knife and was then unable to take the cartridge set out in the open where I could reinsert the yellow cartridge back in place. This kind of thing can happen and not be easily identified or corrected is something of a classic design flaw. In a Word, it should have been anticipated by the manufacturer.

  And that's all.

• Problem installing G510n - "open cartridge access door.

  I want to install a printer/copier/fax g510n - just installed the ink cartridges and still receive the error message 'cartridge access door open - closed door acess cartridge' even if I closed the door.  I can't continue the installation. Suggestions?

  Hello

  Thanks for the post.  With this one, I might suggest the following two links below.  The first is a t - shooting document that covers the common things to look for with this error message.  Good luck!

  http://support.HP.com/us-en/document/c01952299

  http://support.HP.com/us-en/document/c00829896

• Remove and check print cartridge error sign

  I have a HP Photosmart C4150 all-in-one printer.  The ink cartridges are newish.  When I try to print a web page or a page in MS Word, the message remove and check print cartridges appears.  I removed both cartridges and re - install, but without success.  I have a MacBook Pro.

  How long were these cartridges in the printer? You can try to clean the contacts by following the steps below.

  First step: remove and check cartridge

  The print cartridge cannot have a full electrical contact with the printer. Can help to remove, and then reinstall the cartridge. To remove and inspect the cartridge, follow these steps:

  NOTE: HP does not guarantee the quality of remanufactured or refilled cartridges.

  1. Make sure that the printer is turned on. If it is not lit, press the power button.

  2. Open the printer cover, and then wait the carriage is idle and silent.

  3. Press gently on top of the cartridge to release it.

     Figure 2: Removing the Tricolor cartridge

     

  4. Slide the cartridge out and review it.

     Warning: Do not touch the electrical contacts or the ink nozzles.

     Figure 3: Electrical contacts and nozzles

     

     1 - copper electrical contacts

     2 - nozzles

     • Check the electrical contacts for debris.

• 940c print cartridge question

  Hello!  The print cartridge is flashing on my 940 c and so the printer does not print.  I installed new color and black cartridges for only this problem - no solution.  I pulled out, put them back and waved them, open the cover, closed the lid... all I can think.  I watched the previous answers to questions like that and have made sure it is plugged directly into the wall. I looked at the guide to what the lights mean on the HP website, but can't seem to find a solution that works.  I got a call from the ink on with the last cartridges installed (not sure what cartridge was the culprit - they look very good, just black ink everywhere else)-ink got everywhere inside the printer when it was stored for a period of time.  I'm almost certain that this is what is complicate measures here.  I cleaned all surfaces I can reach (on a q - Tip rubbing alcohol), but that did not stop light either. Thoughts before I declare patients dead?  Thank you!

  That the users of the water-based ink printer, clean with water!   Clean the contacts in the transport and on the ink cartridge.   I still have parts for this model amd probably still a whole unit in my basement.

• Photosmart 2710 need to change region for the printer cartridges

  Hello:

  I am an international resident currently residing in the Brazil. My printer is programmed for Asian print cartridges and the region needs to be changed so that I can buy cartridges locally.

  When I changed from Europe to Asia, HP Singapore support has been very helpful and English speaking. Support for the Brazil speaks only Portuguese and I need instructions in English.

  Who should I contact for that, that I am out of warranty and the HP website is a labyrinth of unhelpfulness, if you are no longer under warranty.

  You will need to Contact HP to ask a "regionalization Reset." Do not charge for this, it is covered under the warranty of the cartridge. You will need to have access to your computer and printer then on line with HP. You will also need to have a set of cartridges for the new region, once completed reset cartridges of region of origin no longer works.  Webpage of HP on the subject is here.

• Officejet Pro 8500 A909a print cartridge jam

  I removed the filter switch and the 2nd optional drawer.  I can't find any sign of a paper jam.  The print cartridge is stuck on the right side and I can't reach in this place.  There is what appears to be a hatch above where it is blocked, but I can't open door - I fear I'll break it.  The printer is barely a year - of ideas?

  Yes, I did all this.  I was finally able to reach in and find a part to seize the cartridge and on top.  Still can't get off the cover - looks like it is supposed to just swipe, but it wouldn't be fair.  Anyway, once I manually moved the cartridge, I reinstalled the cartridges.  Seems to be ok now.  Thank you.

• Incompatible print cartridge Photosmart C4780

  Bought a printer Photosmart C4780 USA and brought it to UK

  Used 60XL (CC644WN) print cartridges in the United States

  United Kingdom bought real HP 300XL black print cartridge (CC64EE UUS)

  Laid out, cartridge black HP 300XL but printing gives the incompatible cartridge error!

  Says on the box for use in HP Photosmart C4780

  Help please

  If you bought the printer in an area and moved to a new area, you must call customer service to ask a "regionalization Reset." Avoid any accusation to this effect; It is covered under the warranty of the cartridge. You will need to have access to your computer and printer then on line with HP. You will also need to have a set of cartridges for the new region, once completed reset cartridges of region of origin no longer works. See the document on regionalisation.

  http://support.HP.com/us-en/document/c02558798

  Contact HP worldwide | HP

  Jason

• HP C7280: ink cartridge access door is open

  Hello

  My HP Potosmart C7280 AIO (all-in-one) is stuck with an error message.

  Door open

  Ink cartridge access door is open.

  I have reeived a printer replacement in support of July 2008 and HP will not help because my original printer was purchased in Dec 2007.

  Google did not help

  Search HP support site did not help

  User manual did not help.

  I also tried this:

  power off

  Unplug the power cable

  Wait a minute

  Press and hold the "#" and "6" keys

  Plug in power chords

  Be patient

  Wait for the white screen out.

  Release the keys #6

  Press the button power

  ... all of this in the hope that a false alert will disappear. There NO :-(

  Experts out there?

  Is - this firmware/hardware translation?

  In the future, I'm not spending a dime more with HP unless this issue is resolved in a satisfactory manner.

  Help to get forward.

  Pete

  Message edited by prnthlp on 05/21/2009 12:27

  I also sent the email below to HP support and hoping that someone will help.

  Sent by e-mail E-mail form
  Please contact the e-mail HP support

  Thank you for sending your e-mail to the customer of Hewlett-Packard. You will receive a system generated acknowledgement [[the lapse of time, may vary by region]]. If you do not, please resubmit take extra precautions to make sure that you enter a valid and functional e-mail address.

  If you have additional information or request for information, please contact HP

  
  When did you purchase your product? : 2008

  Product HP Photosmart C7280 all-in-One Printer

  Select a problem area: error messages

  What is your serial number (SN): MY82NH43NC

  What is your operating system? : Microsoft Windows Vista Home Premium 64

  How your product is connected to your PC? USB cable
  
  If there is an error message, please specify:

  Door opening / Inc. cartridge access door is open

  Description of the problem: the ink cartridge access door is not open, but this post just won't go away! The printer is in normal state (not open) and I am ready to print. How can I get rid off the coast of this message. Help, please.

  Please provide previous steps of troubleshooting, or information that can help HP help you. :

  I tried to plug the printer in holding together the "#" and "6". In the past it has helped to solve other problems of the firmware, but this time the message "access cartridge door is open" message remains on.

  Nothing changed since the device was working properly (installation of SW, settings, wiring, etc.): Nop.

  How would you describe your level of technical skill? : Advanced