Printer Deskjet HP 2540: network name

Similar Questions

• HP deskjet printer: what ink cartridges I get for my printer deskjet HP 2540

  What are the correct ink for my printer.

  Hi ann24,

  Here's what I found for all-in-one printer, HP Deskjet 2540

  under printer Specifications on the HP support page:

  HP black 61

  HP 61 tricolor

  I hope this helps!

• Printer wireless network name recognition

  I have an all-in-One of C4795 printer, on Vista 64-bit, which can not connect again ATT Uverse router. The router has been replaced and printer identifies the old network name/number. I tried everything the HP web site offers, but nothing worksI. At some point in the implementation I find the new name/number and I printed the report of NetworkTest wireless and it shows the old name/number. Help! Joe C.

  Hi Joey1969,
  
  Follow these steps in the document below. Let me know if you need help.
  
  http://goo.GL/jXYCw

• HP Deskjet 2050 print in a wireless network?

  Hello world!

  I watched this videoand follow these steps, but it seemed impossible to print my printer wifi, then what should I need to print in my network.

  Also, I have 2 desktop computers (1 router to connect to the internet and 1 printer, use wifi) and 1 laptop (wifi use).

  1. Office has the modem, Windows 7 64 bit.
  2. Office printer, use Windows XP SP3.
  3. Laptop using Windows 7 64 bit.

  If it is possible to print in a wireless network of my HP Deskjet 2050, I can print from my laptop without turning on 1 desktop printer or not, just that the printer lights? And what I have to install each office and cell phones, drivers of the printer? 

  I mean just 1 desktop computer a Modem lights and I'm working on laptop.

  Thank you for reading and re-reading!

  Well, you can turn the impression on the host PC sharing, then load the drivers on the other PC and print via the host PC.

  The host computer must be turned on (not sleeping).  Also, this is going to share the printer, but cannot share the analysis.  If the host computer has to one different operating system than the others, it can be difficult and is not all that reliable.

  It's as good as it gets with a USB printer only.  If you want more you have to get a wireless printer.

• All-in-one HP Deskjet 2540: delete at the request of print job on a deskjet printer MAC OS 2540 x 10.9

  How can I delete a regular print job to a 2540 MAC OSX 10.9 deskjet printer.  I can pause, but may not know how to remove it completely.

  Hello @annetrumbo,

  Welcome to the Forums of HP Support!
  
  I would like to help you today with removal of a print job in the print queue for your all-in-one printer of HP Deskjet 2540 on your computer Mac OS X 10.9. Can I please you follow the steps below.

  1. click on the Apple icon in the upper left corner of your computer screen

  2. click on System Preferences

  3. click on Print & Scan

  4. click on printer Deskjet on the left to highlight

  5. click on Open Print Queue on the right side

  

  6. in the print queue window, click the print job you want to delete. Then click on Remove in the top left corner. Once the print queue window is clear, you will have a nice clean slate for your printer.

  Please let me know if this procedure works for you. Good luck!

• Network Name (SSID) Found failed is the message that I received after the test run. Cannot access my printer.

  I can't print my coupons to my email... ran a test and it say network name (SSID found) fail... but it says that the printer is ready and online?

  Hello

  1. don't you make changes to your computer before the problem?
  2. what operating system is installed on your computer?

  Please follow the steps in this link:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/wireless-printer-goes-offline-with-a-message/d83e6dcd-AF35-4e55-9516-47944e70a125

• Printe all-in-one Deskjet 3520: cannot reconnect my printer all-in-one Deskjet 3520 wireless network

  Hello!

  I'm having a problem to reconnect my printer on the wireless network. I unplugged for a few days and now it won't connect to the wireless network. I get the following message on the small screen on the IP of the printer: not connected SSID:N / A. I hope you can help me solve this problem.

  Best regards

  Mina

  Hi @Mina85 and welcome to the Forums of HP!

  I see that you are having connectivity problems.  I would try to help!

  I recommend you to perform a power reset.   Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I also suggest this document on Center of troubleshooting wireless printing.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• printer deskjet HP 2545: forgotten password wireless printer

  Please help me remember my password wifi printer

  This informtion is in your User Guide I have uploaded to the web.  You must print the Network Setup page of the printer on page 6 of the user's Guide.

  http://support.HP.com/us-en/product/HP-DeskJet-ink-advantage-2540-all-in-one-printer-series/5285095/model/5285096/manuals

  Print the network configuration page.
  The network configuration page displays the network
  status, host name, network name, and more.

  Press the wireless button and the button to launch the copy in black from the printer control panel at the same time.

  Once printed glue to the top of your printer so that you won't forget.

• How to connect a USB-wireless printer to a wireless network without PC

  Some HP printers do not have a Wizard of wireless configuration integrated into the façade to connect to a network.  These models install to a computer via a USB connection and the software then sends information wireless via the USB cable to the printer.  However, you do not always have a present computer and still need to connect these printers to a wireless network.  You can use a wireless, like an iPad device, to do this.  For the example below, I used an iPad and a printer Deskjet 3510.

  The first step is to make sure that your printer is aired at an (Ad Hoc) network.  To do this, turn on the printer and press the wireless or wireless Tower, and then in the Setup menu. Connect the iPad (or other wireless device) to the signal being broadcast by the printer wireless.

  Once the iPad is connected to the printer as long as a network connection, open the Web browser on the iPad.  Type 192.168.223.1 in the address bar and go to this site.  Printer status page should load and look like the picture below.

  

  Click the network at the top of the status page.  You can get a quick warning while being redirected to an HTTPS site.  Click Ok in the message box to continue.  When you click OK, you can get a warning about the identity of the server or the certificate.  Select the option that allows you to continue.  The wording can vary from a browser, but there should be an option to continue anyway.

  Network status page should now be loaded at this point.  Select Assistant wireless to start the installation of the wireless network and click Next.

  

  When then is selected, it must list the available wireless networks.  Select your network from the list and click Next.  When the network is selected, it should be noted.

  Enter the network password if necessary and click Next.

  

  A message should be received indicating the name and if security is enabled.  The message below which must indicate that the settings have been saved successfully.  If it indicates that the settings were saved successfully with an error, the configuration of the network is more than likely operation.  Click Ok at the bottom.

  

  After selecting OK, select status to check that the printer is connected successfully.  It may take a few minutes for light wireless to the printer to stop flashing.  Once it is a solid blue, the printer must be on the network and operation.

  

  Once this is over, then you will be able to reconnect to your wireless (wireless router) normal signal for internet access.  Now, the iPad and the printer are on the same home network.

  I hope this helps.

• How can I get my USB to the printer wirelessly to a network without a computer?

  If you have a USB port to the wireless printer and no computer to use software to do this and do not want to use the WPS option (or it is not available), then the following method can help.

  That doesn't get a key USB Wi - Fi, as the printer Deskjet 3512, on the wireless network when there is no computer available.  However, this can work from a computer as well if you prefer not to install the software.

  For these steps, I'll use an iPad.

  1. the printer will broadcast a wireless network of its own.  This has usually HP Setup and model of the printer in the name of the network.  Connect a wireless device to the network.

  2. Once connected, open the browser.  In my case, it's Safari.

  3. Enter the 192.168.223.1 address in the address and press go to access the status of the printer page.

  4. once there, there will be several tabs at the top.  Select network.

  5. Select the wireless configuration wizard.

  6 Select next at the bottom.

  7. it looks for available networks.  Select your network from the list and click Next.  The network should be highlighted, select it again if it's not.

  8. you will be asked the password.  Enter the password and click Next at the bottom.

  9. the printer should now be connected to the network.  It may take a few minutes to share.  Reconnect the computer or mobile device to your regular network and it should be good to go.

  I know that there are some users who have only a Tablet and a USB port to the printer wireless with no other way to get it on a network.

  I hope this information is useful to someone.

• Windows 7 deskjet 5652 on network

  I have a deskjet 5652 printer connected via usb to a windows xp computer.

  I have a windows 7 windows xp wireless computer networking.

  I want to share the printer with windows computer 7.

  I have shared the printer and can see the printer on the network, but I get an error message - drivers cannot be found.

  I used the hp print and scan doctor telling me to connect the printer to the computer windows 7 via usb first to extract and install the drivers for windows 7 OS.

  What I did, but how you can spot Windows OS printer drivers once re, the printer is connected to the windows xp computer

  Hi Jason,

  Thank you for your help. I managed on the basis to solve the problem by following these steps.

  I installed the printer deskjet 990c on the computer windows XP windows drivers (even if the printer is a deskjet 5652.

  I shared the printer deskjet 990c on the network. I then installed the printer Deskjet 990c by adding a network printer on the computer windows 7. It extracted the drivers of 990c and the problem is solved. I am now able to print from my computer windows 7, fool the computer on which it is printing to the printer of 990c although it is in fact the 5652 printer printing.

• Printer cannot find the network

  I just bought a new printer HP Photosmart 5514.  I tried to connect to my wireless router, but he can't find it. I checked to make sure that the router was conducted, it was broadcasting the SSID and I have was close enough to receive the signal. Everything was ok, but it has always failed. I still don't see it.  (On a side note, 2 laptops can see the router and another 1 laptop can't see the router). I think I might be missing just a setting somewhere but can't find it.  Help, please!

  I have a Linksys WRT320n.

  Wireless broadband: 5 GHz
  Network mode: mixed
  The network name (SSID): wire78
  Channel width: Auto (20 & 40 MHz)
  Channel: Auto
  SSID Broadcast: enabled

  Security: WPA2 Personal with a password

  MAC filtering: disabled

  I found the error.  I needed to have the band Wireless 2.4 GHz.  Fixed both the problem of connectivity to the printer and the laptop that did not see the network.

• Photosmart all-in-one printer: loss of the network printer connection

  My wife has worked with verizon until our internet high speed - it was realized from wep to wpa2 - it has helped our speed but now the printer does not connect to our network eventhough our network name and password are correct. How can I get this fixed?

  bobnall wrote:

  My wife has worked with verizon until our internet high speed - it was realized from wep to wpa2 - it has helped our speed but now the printer does not connect to our network eventhough our network name and password are correct. How can I get this fixed?

  Most likely, you will need to re-run the installation of the network.

  Since you changed the encryption WPA2, the printer needs to know this!

  WyreNut

• How can I add a printer to my wireless network

  How can I add a printer to my wireless network

  John

  I assume that you have a wireless printer. If so, the software is different from each manufacturer, but it is similar to this. Before starting the installation, make sure that you have a USB cable at your fingertips and you know your network name (SSID) and wireless key. Install the software and follow the prompts to set up the connection Wireless for the first time. Once it has been set up you can unplug the USB cable.

  The USB cable is not required on subsequent computers, simply install the software and follow the prompts on the screen of an additional computer (or similar wording). You may need to enter an SSID and Wi - Fi key, after which the printer must be accounted for.

• OfficeJet 6700 cannot find the printer on the wireless network

  Printer is connected to my wireless network.

  Print diagnostic shows PASS for everything and I have ip (DHCP 192.168.2.19)

  The printer is able to connect to the internet to download updates and pull content for apps (colouring etc...)

  I disabled my firewall of windows to resolve the problems, but the HP software was listed as exceptions anyway.

  Using the printer on my computer connection wizard I entered both the IP address and the host name but it is "impossible to find the printer.

  My router is a netgear WNDR3700.

  The ssid that I am connected is good.  I have a network of both comments, but it does not broadcast its ssid and I am not connected to it.

  I am getting very frustrated.  I'm tech-saavy and it should be much easier than this.

  I wonder if anyone else encountered this problem and can anyone offer suggestions?

  Thanks in advance...

  Hi mbelsey,

  By following the steps below resets the defaults on the printer. Reconnect the printer to the wireless network using the address assigned to the router DHCP. Once you have connected it to try to access the EWS and Ping the printer. Let me know what you find?

  First step: restore the default settings of network on your product