Printer will not print but will scan and photocopy HP Photosmart B109n-z

Similar Questions

• 5640 envy: Envy 5640-can we print but cannot scan

  Hello

  I can print but cannot scan. I restarted it printer and pc, plug in the printer and the computer, the HP scan doctor and did the updates. Scanning HP doctor break WIA Scan this part and not finished troubleshooting.

  How can I solve this? Thank you.

  Hello

  Thank you for using the forum.  You will need to install the full features printing software to scan.

  You have downloaded and installed the software features FULL?

  Here "link for your convenience;

  http://support.HP.com/us-en/drivers/selfservice/HP-envy-5640-e-all-in-one-printer-series/6583033/model/6583034#Z7_3054ICK0K8UDA0AQC11TA930C7

  Please select the correct operating system and download the FULL features software.

  We recommend that you uninstall the current software before you reinstall the downloaded software.

  You can try using the Auto Connect Wireless HP if your want a wireless connection of your computer to your printer.

  You will need restore your network wireless to factory default using the Auto Connect Wireless HP.

  There are the following videos very useful for wireless setup.

  Restore the printer network settings

  https://goo.GL/9fyrGS

  Setting up the printer using HP Auto Connect Wireless wireless

  https://goo.GL/oBY6AJ

  Let us know how it turns out.

  Thank you.

• my CD player repeat myself no CD not loaded but there is and it won't record from windows Media... Help

  my CD player repeat myself no CD not loaded but there is and it won't record from windows Media... Help

  Hello

  1. What is the exact error message associated with no CD loaded?

  2. do you mean to say Windows Media center?

  Perform the steps from the link below and see if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or any other programs (Fixit)

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/

  Hope this information helps.

• My dell 964 will print but now scan events.

  My multitack dell 964 printer will print but not scan.  Help.  Thank you

  Hello
   
  1. do you get any error message when trying to scan?
   
  Many Dell printer users have solved this problem by installing the additional software supplied with the CD/DVD printer.
  Put the printer disc in the CD/DVD drive, follow the instructions in the Dell installation screen to install software or additional components and check the result.

  Windows Image Acquisition service provides image acquisition services for scanners and cameras. Check if this service is started.
  1. Click Start, type services.msc and press to enter.
  2. from the list of components, double-click the service Acquisition of Image Windows (WIA).
  3. change the startup type to automatic, and then click Start.
  4 apply the settings, and then click ok.

  The problems of scanning: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-scanning-problems
   
  For more support options, you can post your request here:
  http://en.community.Dell.com/forums/
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Mac 10.5.8/HP Photosmart C4280 printer ORDER (will scan and copy ok)

  Help!  My printer scans and copies, but will not be printed.  I tried all the suggestions on the HP site, but none of the solutions proposed ago solved my problem.  How to DÉBOUCHERAS my printer?

  We will uninstall the software by using the "scrubber":

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt Cmd and click on uninstall< scrubber="">
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Restart your Mac

  Now run a software update.

  Finally, download and install the "Full Featured" driver and software from the "Support & drivers" link at the top of this page.

• I try to get my Lexmark printer scanner to scan and it tells me that the scanning functions are not configured for program wnidows 7. How can I fix it?

  How can I get my Lexmark printer scanner to scan with windows 7?

  wnaza wrote:
  > How can I get my Lexmark printer scanner to scan with windows 7?

  Contact Lexmark to get Win7 drivers for devices and software for it
  specific model scanner.

  --

  Bruce Chambers

  Help us help you:
  http://www.CatB.org/~ESR/FAQs/smart-questions.html

  http://support.Microsoft.com/default.aspx/KB/555375

  They who can give up liberty for a little temporary
  n Franklin

  A lot of people could die rather that thinking; in fact, most do. ~ Bertrand Russell

  The philosopher never killed the priests, while the priest was
  has killed a large number of philosophers.
  ~ Denis Diderot

• Very frustrated! Can print but cannot scan

  HI -.

  I have a PC with Vista and a C4280 all-in-one.  No problem printing, but it behaves as if there is no connection between the printer and the scanner when I try to scan.  I can't even open the HP Solution Center.  When I do I get the error: No. HP devices have been detected.  HP Solution Center will be closed.

  I did research on what to do and I tried to uninstall, then reinstall the driver, disconnect all cables and usb.  I know I'm not the only one who has this problem, but none so I see a ton of questions about topics I read enabled.

  Don't mean to be grumpy, but I am VERY FRUSTATRED!  Can anyone help?  Thanks a lot if you have any ideas.

  Bazzie

  Hi Bazzie2014,

  I want to help you to scan from your c4280.

  Please use the HP print and Scan doctor. Printing HP and doctor Scan is a free utility (tool) that allows to quickly solve common printing, scanning and connectivity problems, including but not limited to:

   

• Unable to connect to a network printer, but can see and discover

  I'd appreciate any help with this: I have exhausted my Google searches for most of the day, and Microsoft support articles are of course a great help.

  The problem: I have a printer installation on one of the XP Home computers in our home network (all the XP Home computers). I am trying to connect to this printer from another computer, but I'm unable to add through the "Add printer" Wizard While I can see the printer in the list of printers on a network (including two other printers on other machines that work), when I try to connect to this particular printer in question, I am struck with a challenge to connect with what seems to be the guest account on the computer. There is no password for this account so I leave the password blank, and I then told me that I do not have sufficient permissions. I don't know what to do.

  A few pieces of my Google-ing info that may be useful:

  (1) I made sure that the guest account is enabled and even perform the active command of the net user on the computer in question.
  (2) I use Windows Firewall and I said to turn on the printer and file sharing and have exceptions for such.
  (3) I use Microsoft Security Essentials.

  (4) given that it is XP Home of course I can't access everything related to security or other policy.

  In addition, whenever I try to access this computer on the Working Group, it says I have "insufficient permissions". I don't know what it means that I've never been specified no restrictions when I ran the Network Setup Wizard.

  Windows networking works better if you have matching user accounts password on each machine rather than try to rely on the guest account (which is a security hole).

  See the following tips from the old MS MVP Malke.  He's old, but it's always good.  Not everything can be applied to your situation; Take the parts that do.

  The best and simplest is to buy a wireless router. This way you get Internet connectivity both machines and the added benefit of security more between you and the Internet. Then you configure your network wireless safely, and then you configure file/printer sharing. Here is information on the implementation of a router and also in networking. It seems long, but don't be intimidated. Setting up a router and the LAN of sharing between two computers takes about 15 minutes.

  The router configuration

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.

  2. attach a cable (usually supplied with the router) course Ethernet cat5e Internet/WAN port of the router to the Ethernet port on the cable modem.

  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.

  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

   

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar.

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). If you have a newish computer, you will be able to affect security WPA2-Personal Mode. Do this and enter a password. The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the Ethernet cable and wireless of the computer should see your new network. Enter the password you created to join the network and start surfing.

  *****

  B. file/printer sharing of

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus with "Internet Worm Protection" (like Norton 2006/07) which acts as a firewall, you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this. The instructions on this link work for XP and Vista:

  Set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.

• Kodak c310 prints but stopped scanning

  my printer has a reason any stopped my pc regonising in the menu when you print ideas

  Hi Andy,.

  -What version of windows is installed on your computer?

  -Is a printer wired or wireless?

  -Do you get any error message or error code when you try to scan?

  I suggest you to uninstall and reinstall the printer drivers Kodak c310 and check if it helps.

  For uninstallation,.

  http://support.en.kodak.com/app/answers/detail/A_ID/1346/kW/Kodak%20ESP%20c310%20Printer%20drivers/selected/true

  To re-setup,.

  http://support.en.kodak.com/app/answers/detail/A_ID/36670/~/Kodak-EasyShare-software---Windows-operating-systems/selected/true

  It will be useful.

• Photosmart Premium C410 can print but cannot scan

  This printer has been installed and working properly on our home wireless network.

  This morning (coincidentally or not?) after a Windows update last night, this morning, I can't open the solution Center HP to scan; He told me that my installation is incomplete.

  I then tried on our another computer (which has not been used recently and so doesn't have the latest update of Windows Installer) and was able to scan successfully.

  Now, when I try to scan directly from the printer, it does not recognize my laptop and scans directly to the other PC (and yet I can print to it).

  After several unsuccessful attempts, I finally got to re - install the two HP Solution Center and the printer (since the last driver available online) driver. Still having the same problem.

  I've removed what I could from Windows yesterday updated (although it is dated yesterday) but unable to remove one for Silverlight. It made no difference.

  I would like suggestions as to what I can do.

  Hello

  Download and run the HP utility digitization of diagnostic located here. It can solve a lot of problems and if not give us a better idea of what is happening with the printer.

  Good luck!

• Can print but cannot scan Photosmart HP 6510

  After being able to print and scan at my Photosmart HP 6510 my VIAO laptop Ultrabook, for some reason, I lost the ability to analyze.  Whenever I try, I get the error message "the scanner is currently in use. Wait until your previous task is completed, and then try again. "The problem is the scanner is not in use and I do not see how to delete it.  This same printer/scanner device other users can connect their computers and scan from it.

  What program you use to create the scans and what file format you saved scans - PdF, JPG, TIF?

  I suggest using assistant installation automated HP.

  Go to http://www8.hp.com/us/en/troubleshooting.html

  Work carefully through the steps to detect your printer through the option to allow web service from HP to install the necessary drivers.

• HP Officejet Pro 8610e: cannot print documents I scanned and saved as pdf files

  All of a sudden I cannot print I scanned and saved as pdf files.  I get a message indicating that the printer is "Impossible to convert the PostScript file.  Don't know how to handle, but I have to be able to print the docs I'm scanning and saving in pdf format.  Can someone help me?

  Thank you

  GTR

  Hi @GTR3,

  Welcome to the Forum from HP Support.

  I see that you are unable to print the PDF scanned documents with your HP Officejet Pro 8610 e-all-in-one printer. I would like to help.

  You are able to print any other format PDF on the Mac, or the question is just limited to your scanned PDF files? Whether the soft friendly PDF work with - Adobe Reader or Foxit Reader?

  In the meantime, I recommend you try the following steps:

  • Uninstall your printer - click here for instructions.
  • Fix permissions of the disc on your Mac - click here for instructions.
  • Once you have finished running the utility above, restart your computer.
  • Finally, click here to reinstall your printer.

  Please let me know the result of your troubleshooting by responding to this post. If I helped you to solve the problem, feel free to give me a virtual h.o.t. by clicking the "Thumbs Up" icon below and by clicking to accept this solution.

  Thanks for posting in the Forum from HP Support. Have a great day!

• I have printer HP C4680 scans and copies to the Jeg can be converted to Pdf for printing.

  How to convert software for the HP C4680 printer print queue?  See the topic shown.

  Hello

  Why it prints as jpg files, I don't know, but you should be able to scan and print as a pdf with the following product:

  http://en.pdf24.org/pdf-editor.jsp

  You can download and install on your computer. You can open it to scan in PDF format and you can also print documents in the form of PDF files. A good thing: you can also use it to edit PDF files.

  Kind regards.

• My ipod touch does not illuminate, but siri works and turn on randomly.

  I was using my ipod and then it froze from nowhere. So, I turn it off using the power button. But, siri was turning, and saying: "I don't have that." Although I do not have suumon him. And now my ipod turns on.

  Try to keep the sleep/wake and home button until the apple logo appears or 15-20 seconds. -AJ

• I don't know but its all white: my tablet screen does not light, but the sounds and touch are ok. Please help me!

  I dropped it and now the screen does not light, but sounds like the notifications are on.

  Hi!, Sensei:

  Welcome to Forum!

  To help you, is necessary that you enter make, model (without serial number) and operating system.