Printer wireless network name recognition

I have an all-in-One of C4795 printer, on Vista 64-bit, which can not connect again ATT Uverse router. The router has been replaced and printer identifies the old network name/number. I tried everything the HP web site offers, but nothing worksI. At some point in the implementation I find the new name/number and I printed the report of NetworkTest wireless and it shows the old name/number. Help! Joe C.

Hi Joey1969,

Follow these steps in the document below. Let me know if you need help.

http://goo.GL/jXYCw

Tags: HP Printers

Similar Questions

  • How to install a HP printer wireless network using an Access Point in Windows 7


    Let me know if you have any questions or need help to install a HP printer wireless network using an Access Point in Windows 7.

  • mg7720 wireless network name change

    How can I change the name of the printer wireless?

    Hi Rjw1952,

    To connect your PIXMA MG7720 to your wireless network, please follow these steps:

    1. press the button on your MG7720 PIXMA HOME.

    2. slide the screen, and then select LAN settings.

    3. tap on settings WLAN.

    4. click on installation Standard.

    5. a list of detected access points appears.  Select your wireless network.

    6. Enter your wireless network password, and then click OK.

    Your PIXMA MG7720 will now be connected to your network.

    If you continue to have difficulties, please contact our support group by using the following link:

    http://www.USA.Canon.com/Cusa/consumer/standard_display/contact_us_consumer

  • Hp1102w connection printer wireless network problems

    I can't get my connection between my Linksys WRT54G and my printer wireless hp1102w wireless. The configuration page shows the following: network not connected, I have a host name, hardware address. There is 0.0.0.0 for IPv4, the IP subnet mask & gateway IP. Configured IP said manual.

    Under wireless 802.1b/g/n: status: activated, common mode: infrastructure, my name network & authentic WPA/WPA2
    Under Direct Print Config: Off, HP-Print-40-Laser Jet 1102, Channel 6 and there is an IP v4 address. What should I do?

    Also my iPad4 does not see the hp1102w printer, do I have to download the software? I don't have a USB connection? I am very new to the Apple OS, if you couldn't tell.

    Salvation, TarNation,

    Welcome to the HP Forums, I hope you enjoy your experience!

    I understand that you are unable to set up the printer on the wireless network.

    I'll be happy to help you.

    Please provide the following information so that I can better help you.

    What operating system do you use?

    Mac OS X: how to find which Mac OS X Version is on my computer?

    You also have a PC?

    Once the printer is configured on the network, the Ipad connects on behalf of network from the router and the printer should allow you to print using Airpint. You don't need to download software for the Ipad.

    Thanks for posting on the HP Forums.
    Have a wonderful day!

  • do not print to the printer wireless network computers connected to wifi

    Don't know if I'm in the right Forum but here goes.  I work in a dealership service department. I have 4 computers connected to our network. I just bought a pro m426fdw mfp laserjet 4 in 1 ad printer connected to our wifi system because there is no available ethernet jack to connect to the main network. Is there a way to allow my 4 computers send information about this printer wireless?

    If you connected to your wireless network, and then run a report of network printer and find the ip address of the wireless connection. If you're in the list use to load the printer using add it printer, the local printer, create a port and the menu drop-down, choose standard tcp/ip and then follow the instructions on the screen. You can also try to load the disc that came with the printer and see if it will find the printer and load it for you.

  • 6700 printer wireless network installation

    Forgive my ignorance of the computer world, but I got the job of installing a new printer 6700 in the office today.

    We have two computers that had been connected wireless to our old 8500.  I was able to follow the instructions in the box and get MY computer set up, using the supplied CD.  I am able to print.  However, when someone went to print a document

    from THEIR computer, they have not.

    Do not understand how wireless networking works, my question is: do I have to use the CD on their computer in

    order so that it can connect to the printer... or is there something I can do to my computer to add his computer

    to the printer?  Thank you, in advance, for trying to help me.

    Hello ncnash.

    I understand your concerns. The question of your previous post: Yes, you need to install the Officejet 6700 Premium to your other computer, so he can make your Wi - Fi connection otherwise you will not be able to print or scan documents you notice.

    If you have any questions please let me know.

    Ashley

  • HP Laserjet P1102w: P1102w - change password and now I can't print wireless network

    Recently, I changed the network password on our router Cisco Valet and without realizing it seemed to me making the wireless printing stop workinig.

    I can always print to this printer via the USB cable, but it is not found on the wireless network.

    I guess I have entered the time of info the first network I created this printer, but I don't remember how I did it.

    Is there an easy way to reset the password that the printer uses, so we'll see on the wireless network?

    Thanks in advance for any info on how to get this working again.

    Replacement/change your wireless router try here.  Same thing to change your password...

    http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

    However, if you have a gateway device, all devices in gateway (modem + router) are terrible for connectivity and wireless performance.   If this does not work, suggest you put this bridge in full bridge mode device and install your own router of high quality that YOU have full control over.

  • HP LaserJet 200 colorMFP M276nw connects to my wireless network, but will not recognize the printer

    I am trying to set up my wireless printer, and the printer says its is connected to my wireless network, but I can't get my computer to print wireless if I disconnect my regular network and attach the direct wireless network name, which is different and stops my internet to work. How can I get my computer to recognize the printer on my regular wireless network?

    Hi @lelg,

    I understand that you want to configure the printer on the wireless network. I can help you with this.

    Uninstall the printer software.

    Uninstalling the printer software.

    Restore the default settings of the printer.

    Go to Configuration, restore the default values.

    Cycle power to the router and the computer.

    Run the installer on the printer wireless.

    Go to the configuration, Setup, menu wireless network, Wireless Setup Wizard.

    Print a configuration page to get the IP address of the printer.

    Print a Configuration report.

    Select the method.

    If you have a valid IP address for the printer, then try and access the Web built-in to the printer server. Type the IP address in the address bar of your web browser. (Internet Explorer)

    If it loads the page from the network printer then the printer is on the network.

    Download, save, and then run the installation of the software. Color HP LaserJet Pro 200 pilot M276nw MFPS.

    Select your operating system, click Next and click on the software to download and install.

    Test the printer.

    What operating system do you use? How to find the Windows Edition and the Version on your computer.

    Please provide detailed results if you're still having problems.

    Good day!
    Thank you.

  • HP Photosmart C4780 connects not (wireless) on Mac or wireless network

    Sorry for the long post, but please someone help me!

    I bought my new printer a few days (actually 14th) and began to implement on my MacBook Pro with my Wi - Fi, which is routed through a Linksys router and mainly through my desktop computer (a PC with Windows XP). I used the CD that came with the printer to set it up on my Mac and it has set up the fine by USB, but when I try to set up the wireless, I get the following message:

    "Device not connected: to configure the network settings for the selected device, please connect via USB temporarily." The device can be disconnected from the USB once the network settings are transferred. »

    I reconnected and got the same message over and over again, so I decided to set up on my desktop computer instead. This does not work either and I got the same message on my desk I have on my laptop. Uninstalled on both computers, reinstalled and I STILL got the same message. At this point, I'm about to throw all the electronics in my bath tub and be done with them but on the contrary, I checked (and double checked - and triple checked) my router via my browser settings, fact that I know the SSID and the password and reconnected to the network through my laptop... Once again, the same message. I tried the network installation of push, the installation of the network PIN, I feel I have tried everything! Probably miss me something small, but eyes fresh is always an asset.

    Can someone help me? I printed a Test report of the network so that a Page Network Configuration and settings I received both... if need be, I can post the information from my router, in order to verify to implement, but after two days of trying to implement something that should have taken ten minutes (sometimes) I'm at my wits end.

    Network Test report:

    "Your HP printer cannot find your wireless router. Check our wireless router has power. Make sure that your network (SSID) HP printer name exactly matches your router (SSID) wireless network name. If they do not exactly match, run the installation of the wireless network to set up your HP printer. »

    How to change the network name of the printer to match?

    Summary of diagnosis:

    Wireless on: PASS

    Wireless work: PASS

    Find the network name (SSID): FAILURE

    Security: PASS

    The printer settings compatible with the wireless router settings: does not work

    No filtering: does not work

    Related: Does not work

    Signal strength: does not work

    Other networks detected matching your network name (SSID): does not work

    Detected wireless networks: 1

    Downlink Count: 0

    Channel: Does not work

    Although I was given my SSID (which does not match my home network - but how can I change this?) and my MAC address (I guess for the printer), so I didn't have the IP address of my printer has no way for me to get online to check all the settings! Is there another way to get this IP address?

    Summary of configuration:

    Communication mode: Infrastructure

    Authentication type: open

    Encryption: no

    ______________________________________________________________

    Network Setup page:

    General information:

    Network status: offline

    Type of connection: no

    URL to Web server integrated: http://0.0.0.0

    Firmware Version/Hostname/serial number were all given

    Admin password: not set

    802.11 wireless

    Hardware address (MAC): data

    Status: disconnected

    Port 9100

    Status: enabled

    mDNS

    Status: enabled

    Service name: Photosmart C4700 Series [6 last digits of my MAC address]

    SLP

    Status: enabled

    Microsoft Web Services

    WS discovery

    Status: enabled

    WS Print

    Status: enabled

    PC connected (s)

    Address IP/hostname: (nothing is here) Time since last access (mm: SS): (nothing is here)      

    Number of 802.11 networks discovered: 1

    (my correct information of wireless network is here, including the SSID, Mode (Infrastructure), BSSID, Channel, privacy (RSN), Auth (WPA - PSK), Encrypt (TKIP-AES), Signal and WPS (no))

    Help!

    Did you read this on your Verizon FIOS router? : http://h30434.www3.hp.com/t5/Printer-networking-and-wireless/Connection-problems-with-Verizon-FIOS-Actiontec-routers/td-p/892967

  • HP Photosmart Premium C309g suddenly stops printing wireless

    I recently bought this printer. I've set up to print wireless. I installed and uninstalled twice b/c after about three times wireless printing, it stops wireless printing. Here is the order of events.

    (1) install the software according to the instructions

    (2) test page wireless printing, that always works

    (3) other printing things the same day wireless (works fine)

    (4) try to print something wireless as 2-3 days later

    (5) it does not. Get message of the staing HP Solution Center which is obvious: Document cannot print (duh). Through troubleshooting (Windows help). It tells me to make sure that it is the default printer (it is) and then check if it is online. It is usually not. So I choose to do the printer online (which is a sub-question, and I'm sure is related to the problem, why it keeps automatically be disconnected?)

    (6) attempt to print

    (7) message appears saying that HP Photosmart C309g-m offline (Solution Center)

    (8) read troubleshooting tips (HP Solution Center), which tells me to connect via USB to print (which annoys me because there is no available solution that tells you how to restore a wireless communication between the router/computer/printer)

    (9) which I did the first time around, but find that when I connect using the USB, it prints well. Any attempt to return to wireless printing is reflected in steps 7 and 8

    (10) check the connection of the application printer wireless network printing. Indicates that the printer is properly connected wireless. I know that my laptop is on the same network b/c that's the only one I have and my internet connection is not interrupted somehow.

    (11) get frustrated, uninstall and reinstall the printer

    Repeat step 2.

    This has happened twice already, and I bought it so that I COULD print wireless. He must be troublemaker solution Quen uninstall then reinstall the printer each time that happens (up to once a week).

    I have a laptop computer, a printer and a wireless router.

    have a Belkin g MIMO Wireless router

    I own a Dell Inspiron 1520 laptop

    I have a HP Photosmart Premium C309g (bought less than 2 weeks ago)

    I do not turn off the router or printer. Rarely I have turn off the laptop. Reset the router in the past has not helped. Turning and on the printer or the laptop in the past has not helped.

    Issues related to the:

    (1) how to prevent printing to offline on my laptop

    (2) how to restore communiucation between the printer and the laptop computer on the wireless network?

    (3) how do I keep the communication between the computer laptop and printer (and I assume that the router) to go Bye Bye?

    Thank you

    Kenya

    About what you suggest, the IP address remained the same throughout the facilities and absorption.

    However, I have thought of it. I guess that the wireless connection on the printer. I went back to the office and looked at my network settings. I needed to "find" my wireless signal. The first time that I've refreshed my wireless name does not show upward. I refreshed again and POOF! He was there! So I chose and put in my password (I think that his WPA encryption). When he finished the wireless network connection, it is printed on a network status page. Given that I printed this page so many times already I happened to have an old on my desk. I noticed that the IP address is the same (although today, I uninstalled and reinstalled again) on both forms. Anyway, when I returned to my computer (which is in my living room) HP Help Center had a giant green check mark on it and said that the printer is connected. Then I printed something and it worked! YAY! It would be great if HP put in information on the way to reconnect wireless when you get this message "the printer is not connected. Who knows maybe I needed to evacuate to understand! Laughing out loud

    So for everyone out there, if this happens to you:

    1) go to your printer

    (2) select the arrow to see the next menu. (it should be on the right side of the LCD screen, it looks like a triangle on the side)

    (3) select Setup--> network--> network wireless assistant

    (4) the printer will start to search for wireless networks

    (5) choose your network (or the network you are using...  It should be the same as your computer/laptop is on)

    (6) if it is password protected, enter the password/password

    (7) your printer will print a network status page.

    (8) your computer should "recognize" the printer on the network itself. Your HP help window can display a large green check mark (it's a good thing!)

    (9) print what you want!

    * Note I guess that you may need to do this each time the printer goes into sleep mode. Its not that boring!

    -Kenya

  • Change network name

    When I change the name of the network should I reconfigure all printers on the network?

    Potentially, Yes. If your printers are wireless, then you will need to reconfigure with new wireless network name to connect.

  • How to force the Win7 to see the printer wireless

    I installed the software for my HP6310 printer on my laptop Presario CQ56 but he did not see my printer wireless networking so she set up a second printer connected. How can I force the HP Solution Center to use a wireless please. O/s is win7 SP2.

    Thank you

    Teriel9

    teriel9 wrote:

    I installed the software for my HP6310 printer on my laptop Presario CQ56 but he did not see my printer wireless networking so she set up a second printer connected. How can I force the HP Solution Center to use a wireless please. O/s is win7 SP2.

    Thank you

    Teriel9

    I don't see 802.11 a/b/g/n wireless as a capacity of connectivity for each model (6310 and 6310xi) of your printer. It is most likely the reason why your laptop is not 'see' it.

    There is a bluetooth wireless connectivity. It's a different way of connection that allows only printing capacity.

    You give more than the number of series in your laptop so I have no idea if bluetooth wireless is installed as a standard option. If it is not installed, you must buy a bluetooth dongle to wWalMart and set it up to use that feature.

    Best regards
    ERICO

  • Satellite Pro L510 cannot access my wireless network

    The laptop recognizes wireless networks are available but requires a 'logon domain' with my user name and password.
    Where can I find the logon domain? What is it?

    Hi mate

    I don't know how you are trying to connect to the WLAN, but generally you n t need no user to connect to the WLan router password.

    You need, it's the right SSID (wireless network name), Wlan encryption right and good WiFi encryption password.

    First of all, ensuring that the WiFi network has been successfully activated!
    Key combination to select Wlan using FN + F8!
    Also read the manual of use of laptops for more details how to enable the Wlan!

    Then, you must configure the Wlan router every router supports a configuration different procedure but normally you should always have a manual with your router.
    There should be a step by step instruction how configure it!

  • Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

    I got a modem Comcast/Xfinity upgrade. Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

    Whenever you change the modem or modem/router on a network, AirPort Extreme will be reset to the default settings and then set it up again to work properly with the new modem. For this he would be...

    Turn on AirPort Extreme for a few minutes... If it is not already turned on

    Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds, then release it.

    Allow a minute for the AirPort Extreme restart to a slow, flashing amber light status

    Make sure that an Ethernet cable connects to one of the four LAN <-->Ethernet ports on the modem/router on port WAN "O" on AirPort Extreme

    To start the Setup program, click the WiFi icon at the top of the screen on your Mac and are looking for a list of the new AirPort base station

    Just below that, click directly on the AirPort Extreme and then follow the prompts for configuration "Wizard".

    When you configure AirPort Extreme once again, you can use the same wireless network name and the same password that you used with AirPort Extreme with the 'old' modem, if you wish, or use a new wireless network name and password

  • Laptop WiFi problem, «identifying...» (network name) ».

    Hello
    I'm having a problem with the wireless on my laptop. Its a HP Pavilion dv6000 and just under a year of age. I had no problems with the wireless until recently. I use the laptop at home and usually the internet is very well (apart from the occasional disconnection), but when I'm at school do frequently connect to the school network (I am a student of the University, and there are several routers throughout the school and in the many buildings). Sometimes it will connect in one building and I'll switch to another and it does not connect. Each time, he does not connect it always says "identifier...". (wireless network name) ». No amount of repair, restart or reset the network card it won't connect. The strange thing is that sometimes it connects to the router in this building (i.e. library) and sometimes it won't. Whenever I have check the status shows that the laptop is received but does not send do not.

    Help! This problem is really starting to annoy me and I don't want to end up throwing my laptop on the whole of the library.

    Hello

    1st brand one Restore Point so that you can return back if necessary (it shouldn't be though).

    How to create a Vista System Restore Point
    http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
    --------------------------------------------------------------------------

    Actually try updating your driver and disabling the network logon.

    Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
    version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
    Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    Download - SAVE - go where you put it - right click – RUN AS ADMIN.

    You can download several at once however restart after the installation of each of them.

    After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
    manufacturer of system become your backup policies).

    Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
    updated drivers.

    I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
    are almost always old, and you can search drivers manually as needed.

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    ------------------------------------------------------

    Do another restore Point then you can go back to where you were if necessary with new active pilots.

    Make sure you know the details of connection to your wireless router - SSID and password.

    You lose connection when you do and have to redo your logon.

    I would like to delete ALL networks, so you can restore if necessary.

    Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
    lower left click on merge or delete network locations - REMOVE all instances of your network (and the
    others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

    -----------------------------------------------------

    Check this box:

    Strange problem with Internet under Vista
    http://www.catonett.com/blog/archives/194

    Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
    http://support.Microsoft.com/kb/928233/en-us

    ----------------------------------------------------

    And:

    Network connection problems
    http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

Maybe you are looking for

  • Satellite P20-304 P43: [b] internal modem problem! [/ b]

    Hi guys,. When I click on my connection I see this message: "Error 633...". etc ". I click redial but Error 633is still there and I can not be connected to the web. I checked in my device manager and on the general tab, I read: "this device is workin

  • Pavilion dv7-6157nr: computer won't recognize 6770M

    Recently, while I was using my laptop I noticed that Catalyst Control Center has been the opening is no longer and I could not move from an integrated and dedicated graphics more. Being very intrigued, I decided to try to reinstall the graphics drive

  • 5 s update to iOS 9.2.1

    5 s will not be updated to iOS 9.2.1 by saying that I am not connected to the internet when I am.

  • HP Pavilion dv6 notebook PC

    Enter the administrator password or power on password appears, my password does not work and then pops up a message that says 'off System [99476174]' it please help someone

  • Office Pro 8500 a: Code B8966C64

    I've got this show # up on the screen of the printer. B8966C64...  What it means? How can I clear it... I tried to turn it off by the power button, but it does not work... can not turn off it... Can I just unplug it and see what happens