Pro - 100 does not wake

Similar Questions

• Macbook Pro retina does not illuminate

  Hi all

  I have a 2015 13 "Macbook Pro, that will not start at all. Last night I came back after a day holiday and powered to the top of my Macbook for the first time in two weeks. The battery level was around 25%, so I plugged the magsafe and did some navigation / watching Youtube. I noticed the GET a little slow mac and a youtube video stutter a bit, but it was late so I was not too concerned and put the Mac to sleep mode by closing the lid.

  This morning, after waking up, I noticed that the magsafe light was still orange, which seemed strange to me as he did pay for one night for a good 10 hours. I opened the cover, but the mac does not wake up. I pressed the power button and the computer booted. At first, everything seemed OK but the computer seems slow and internet soon.

  As the bright light battery was still orange that I flew over the battery icon, which showed 100%. I unplugged the magsafe and he fell immediately to 0%, so I reconnected it. I went to make a diagnosis, however about 20-30 seconds later the computer shuts down.

  Since then, he failed to power to the top of all and nothing I have try works. I tried to hold the power button down, but nothing. There is no edge and the caps lock button is not illuminated, so I know that is not a problem of display.

  I left the magsafe plugged in for 4 hours, and it's still orange.

  I have reset the SMC. While this life Magsafe turns green for a few seconds, and then turn the orange back.

  I tried an another magsafe, which is the same, so I've reduced that as a problem.

  I spoke to Apple support, who say it could be the battery and take it to an Apple store. My most close is a 150 miles round trip, and there is no reserves for the next 8 days. I'm sure this will be a hardware problem, but everyone does not accept that it is likely to be the battery? I did have problems with the battery before it and the charge went really well. Would not the Mac boot always if there was a problem with the battery while it is still plugged into the mains?

  Any help or insight is greatly appreciated

  There could be several reasons why your macbook pro turns on.  Just throw the grounds up into the air and choose one.

  Apple stores are not the only places that repair of the Macs.

  APSP (Apple Premium Service Provider)

  International of the APSP and other Services

  APSP outside of the USA

  How to find your nearest Service Premium Apple supplier (DAD)

  

• MacBook Pro (2014) does not charge despite an orange light when plugged

  Hello

  So my 2 year old Macbook Pro (retina) does not load when it is plugged in - spite, projecting the orange light. I have a battery (20%) and it is reduced whenever I use it and will be soon drained.

  Some of the things I've tried

  -Reset SMC - tried but no change after

  -When I use the mac when it is plugged in the battery icon in the top bar done see the support - but there is no increase in % of the battery. Continuous use it starts to fall.

  -During use (and what battery is plugged) - I checked the report system (about this Mac section) - in the energy sector - it is said does not charge (despite being connected, the orange light and the symbol in the top bar)

  What do you think guys that it is? MLB? Battery?

  What I have to replace or can it be fixed?

  If you have the Apple store, take the machine evaluation.  There is no charge for this, but you need an appointment.   The first thing I would check would be the cable.  You have another machine to test this with.

• Apple MacBook Pro 2012 does not start

  2012 Apple MacBook Pro.  Does not start.  Just get the folder with the question mark.  gives possibility to restart with the ERD, but the model doesn't have a hard drive.

  Help the college student needs to access files on the hard drive for the finals.

  Thank you

  What happens when you start to recovery

  OS X: on OS X Recovery - Apple Support

  and repair/disk startup disk via disk utility which is located in the recovery of aid?

  If it is repairable so reinstall OS x, as the article says

  Also here is covered:

  On the screens, you see when you start your Mac - Apple Support

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• Satellite Pro C660 does not illuminate

  Satellite Pro C660 does not illuminate. no noise, no light just fill out the dead.

  any suggestions?

  Hello

  On this virtual path, it is not possible to provide an accurate diagnosis. All you can do is to unplug the power plug, remove the battery and leave it for a while. Then press the power button and hold it for 15 or 20 seconds.
  After doing this connect the power running and try to start again.

  What happens when you do this?

• The product key on my Satellite Pro P300 does not work

  The product key on my Satellite Pro P300 does not work.
  I entered the key from the sticker on the back of the computer. What I am doing wrong?

  Hello

  Why use this product key?

  Firstly the Toshiba recovery image is already enabled and you don t need this key more activations.

  Second, it's an OEM key and it will not work with other versions of Vista!

  Cheers mate

• Satellite Pro 4260DVD does not detect WLAN CardBus

  Hello

  I had a problem with my Satellite Pro 4200 PCMCIA, which worked very well with 2 cards different Ethernet but when I tried to use the WLAN, it could recognize only a SMC EZ Connect 2.4 GHz 11 Mbps Wireless Cardbus Adapter (SMC2635W). I'm now running on XP Service Pack 2 and the big question mark is that XP didn't detect all other cards except the SMC a WLAN.

  I tried the Linksys Wireless-B 2.4 GHz 802. 11B (WPC11 ver.4) and the generic IEEE802.11b WLAN CardBus card 2.4 GHz/11 Mbps but XP has not yet detected the card. The power of the map light was off and blinked only one time that when I plug. Both cards worked great on my old friend laptop IBM, which is finally older than my laptop. I bought this laptop 6 years ago and never had any problems with the front PCMCIA.

  I have worked on this issue with my friend for about a week and we have no idea if this is a hardware or software problem. I first thought that it might be the PCMCIA 16 bits problem but I think that the SMC card is also not the 16 a bit. I did update the BIOS but I don't think it will make all the differences, if I did. Please help me solve this problem that I'm dying to know what really happened. Thank you!

  See you soon,.
  TR

  Hello

  Well, the 4200 Pro Satellite does not for me but I found something on the Sat Pro 4220. This laptop supports PC - Card16 - bit PCMCIA and CardBus 32-bit (2 x PCMCIA type II) or 1 x PCMCIA type III
  In this case I don't think that it? s a matter of 16 bits.

  What you can do is to try to change the settings in the BIOS.
  In the "configuration" box, you can set the configuration of the device to "devices".
  In addition, in the "PC card" box, you can change the mode of the controller "CCIP compatible" or ' cardbus/16-bit' or 'automatic selection '.

  Try all the settings. Maybe one of them will be working.

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• WinXP Pro 2008 does not recognize my computer drivers & load the standard drivers 2001

  WinXP Pro 2008 does not recognize my computer drivers & load the drivers of standard system of 2001; Impossible to upgrade

  then load systemroot, I don't want systemroot, also charges 3.1 drivers, 95, 98. 2000 & winnt 3, 4, 5 &

  Sometimes it runs under DOS only & sometimes not

  I don't want to network & sharing, because there's someone attached to my system & load malware {pirate just deleted} & takes control so I'm at work & then interupts me online with flash & js causing anomalies onscreen, resumes also connection & homepage.

  Now my Norton is denied access (& other programs) & I can't use it

  Suffered disc & reworked several times, I tried the sharding & partitioning is not on all COMPUTERS

  This pirate has done this for 12 years, 7 computers & 5 operating systems.

  SOMETIMES HE TAKES CONTROL OF MOUSE & KEYBORD. YOU SHOULD SEE MY CDROM CONTROL CD ABNORMALLY.

  This is clearly abuse & I am at my wits end! Help me get rid of this danger, please

  but hidden.
  Try this, go to disk management (Control Panel, administrative tools, computer management).
  They appear here? If so, you may need to reassign a drive letter for them.

  If not, look in Device Manager, they appear in red/yellow or is there any "unknown devices"?

  Windows cannot have the drivers either, so you can download the drivers from the manufacturers Web site.

  1. start the computer.
  2. press F8 repeatedly to display the start menu.
  3. Select safe mode in the start menu.
  4. right - click on "my computer".
  5. Select Properties.
  6 select the Hardware tab.
  7. click on the button "Device Manager."
  8. click on the (+) plus sign next to CD/DVD players.
  9. right click on each component and select uninstall
  10. follow steps 9 to all components under this category.
  11. restart the computer.

  It must reload the drivers for the CD/DVD drive.
  or

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00619385&LC=en&cc=us

  check on this site how to connect dvd cd players

  I tried the following to help resolve the problem:
  1 attached Mouse, provided power but does not recognize the device. Assistant add hardware does not yet come upward.
  2. 3 readers USB flash, in every port and they were not recognized or attached.
  3 uninstall all devices of USB root hub and rebooted. No change.
  4 uninstalled all the USB controllers and restarted. No change.
  5 install a logitech mouse driver that is the same as the mouse installed. The mouse has not always recognized.
  6 re-flashed the BIOS. No change
  7. utility of diagnosis of Dell Ran and no problem found with the controllers or the USB ports

• W510 does not wake from sleep

  When I close the lid or let it expire and go to sleep he does not wake up when the cover. It doesn't happen every time, but it happens about 8 links on 10.

  You can tell it's still on, but the screen remains black.

  I searched and didn't find any resolution that worked for me.

  A recommendation was disable incident reports, and that did not work.

  I preformed also all updates of the firmware as well as the upgrade to windows 8.1.

  The problem is exactly the same point 8.1 as it was in windows 8.

  Just to follow up.

  I did a factory reset the origin of windows 8 and the problem disappeared.

  I think it may have been originally caused by my being too aggressive when bloating. I have uninstalled something I shouldn't that caused the problem in the first place.

  In any case;

  problem solved.

• Sony Vegas Pro 9 does not work with QuickTime or MP4 files

  My Sony Vegas Pro 9 does not work with MP4 files or all the Quicktime files. I know this doesn't have much to do with Windows XP but I just thought I would ask, if you need any information I would be happy to give you.

  Take a look at what it fixed my problem with Vegas platinum 9.0.
  http://www.custcenter.com/cgi-bin/sonypictures.cfg/php/enduser/std_adp.php?p_faqid=4787&p_created=1254146741&p_sid=q91HHDok&p_accessibility=0&p_redirect=&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9NCw0JnBfcHJvZHM9MTcmcF9jYXRzPSZwX3B2PTEuMTcmcF9jdj0mcF9wYWdlPTEmcF9zZWFyY2hfdGV4dD1tcDQgcXVpY2t0aW1l&p_li=&p_topview=1
  This is a link to the FAQ from Sony

• Sun disk MemoryStick pro duo does not fit into the laptop

  My disc solar memory stick pro duo does not fit into the laptop Envy nor the memory stick duo adaptor. How can I download my photos?

  Hello

  Whay is your cell phone? Many of them does NOT support memory stick family devices. You can connect your device to your computer OR you can go out and buy a card reader (USB connector, for about $ 10 to $ 15) that supports the USB key and plug it into the USB port on your laptop.

  Kind regards.

• Why is my Windows 7 Ultimate pro. key does not?

  I installed 7ultimate on this laptop as an 'upgrade' but the Pro.Ke. does not work, why?

  the keys are specific edition.

  a pro key only works on pro. If you have ultimate you need a key.

• Adobe Acrobat pro 2015 does not start

  Hello

  I installed Adobe Acrobat pro 2015
  on W2008R2 SP1 Terminalserver. Then, after that, I can't start the acrobat.exe. The Adobe software
  Application Manager warns that it does not work. I would be happy, if you can
  Help.

  
  
  

  APPCRASH

  Anwendungsname: PDApp.exe

  Anwendungsversion: 9.0.0.24

  Anwendungszeitstempel: 54d1cf91

  Fehlermodulname: KERNELBASE.dll

  Fehlermodulversion: 6.1.7601.19160

  Fehlermodulzeitstempel: 56bcd5c3

  Ausnahmecode: 40010006

  Ausnahmeoffset: 0000c52f

  Betriebsystemversion: 6.1.7601.2.1.0.16.7

  Gebietsschema-ID: 1031

  Zusatzinformation 1: c905

  Zusatzinformation 2: c905acd73fb492d62b693d29db51a461

  Zusatzinformation 3: eca1

  Zusatzinformation 4: eca1f0a4ce51a846384e3bcbbb2e4895

  Best regards

  Armindirk

  Hi Anurag,

  Thank you for asking. Attached files for the solution of the problem.

  Best regards

  armindirk

  Von: Anurag_Gupta

  Gesendet: Mittwoch, 19. May 2016 13:22

  Year: Herr Schwatlo

  Vacancies: Adobe Acrobat pro 2015 does not start

  Adobe Acrobat pro 2015 does not start

  created by Anurag_Guptahttps://forums.adobe.com/people/Anurag_Gupta> installation, updated, sign up for Acrobat - & discovers the discussion fullhttps://forums.adobe.com/message/8759659#8759659>

• I created a Javascript script that adds a watermark on the document action "paper print".  This works in Acrobat Pro, but does not work in the drive.

  I created a Javascript script that adds a watermark on the document action "paper print".  This works in Acrobat Pro, but does not work in the drive.  I am a novice using Javascript, so what am I doing wrong?

  Cannot use either addWatermarkFromFile or addWatermarkFromText methods of document with player as shown in the documentation. You can hide/display the form fields and the existing layers, so consider this approach.