Problem creating DEV_PORTAL via the remote control

Similar Questions

• 22D133B: replaced charger DVD - no play, pause, stop, etc via the remote control

  Hello

  I have a 22D1333B in for repair because it would not play the DVD. I replaced the charger DVD (part No. 75040787) and the unit will now play DVDs ok but the DVD section will not respond to the remote control.

  All other TV functions operate via the remote control without any problem. It's just the DVD section.

  I cured the last of them by exchanging the PCB on the new DVD unit with that of the old unit, but this certainly isn't the way to address this problem.

  I downloaded and installed the software on the site of Vestel and updated the software for the Toshiba site. The fault remains.

  Any help to solve this problem would be welcome.

  T.I.A.

  In my opinion the new DVD drive isn't fully compatible with the remote control (type) RC1910 that was included in the box.

  I think you should get in contact with the authorized service provider to fix this

• Tandberg Edge 95 MXP Password reset via the remote control

  Hello

  I try to reset the IP password via the remote control and still get the complaint that the password must be at least 8 characters and the number. I tried all combinaiton of 8 characters and 1 number, 8 characters and 2 numbers, 6 tanks and 2 numbers, 4 characters and 4 numbers, number 8 characters and 1 number 1 and so on. Is there something special about looking for the system?

  Thanks for the support!

  PS. When I telnet into the system, it shows TANDBERG Codec Release F7.2 PAL / SW Release Date: 2008-10-31, so I guess it is 7.2.

  Do you know if strict password is enabled or not?

  By default, that is, unless you have turned it off at some point, which will ask for a password at least 15 characters that contains 2 lowercase letters, 2 caps, 2 numbers and 2 special characters.  You can check by connecting to the endpoint using SSH or Telnet and runs the API command below:

  xConfiguration StrictPassword

  Here are the steps to reset the password to access IP on a TANDBERG MXP endpoint, I suggest that you try to use the API to change the password by logging on to the endpoint by Telnet or SSH instead of the remote control. The most recent software MXP is F9.3.4, suggest you also improve your point of termination to the latest version to mitigate the security issues with the older software. You can contact TAC and advisory security cisco-sa-20140605-openssl to get a key to unlock so you can upgrade your MXP to software F9 of reference, from there, you can upgrade to F9.3.4.

• Programming of the remote control

  I am able to program the buttons on the remote without problem but I have more than 60 deployed MD and would like to be able to program them all at once.  Is there a way to the DMM to write an application of advanced task that will program the remote button?

  Thank you

  Al

  Alan,

  
  

  Here's a technical tip I wrote on the programming of the remote control through the

  a HTTP mib.  Just create a task advanced under the task system

  for each color button.  Test & check if it works on a single DMP first and

  then send task for each color button to all of the DMP.  Once it is

  finished make sure you that you SAVE the configuration.

  
  

  If this answers your question, take the time to mark this

  discussion answered & rate the answer.

  
  

  Thank you!

  
  

  T.

  
  

  
  

  ******************************

  
  

  You can use DMP MIBs to reconfigure the DMP Remote Buttons. VARIABLES =========   admin           = DMP Web Account Username   default         = DMP Web Account Password   a.b.c.d         = IP Address of DMP   dmm.company.com = FQDN of the Digital Media Manager(DMM) Appliance MIBS ==== ** Use the Following MIB to see the CURRENT Remote Mappings https://admin:[email protected]/* */:7777/get_param?p=*.*&init.pop_enable=false ** Configure Buttons RED https://admin:[email protected]/* */:[email protected]/* */[email protected]/* */Dwww.cisco.com%22 GREEN https://admin:[email protected]/* */:[email protected]/* */[email protected]/* */MD%3Dhttp://www.google.com%22 YELLOW https://admin:[email protected]/* */:[email protected]/* */[email protected]/* */_CMD%3Dhttp://www.yahoo.com%22 BLUE https://admin:[email protected]/* */:[email protected]/* */[email protected]/* */%3Dhttp://www.apple.com%22 ASSIGN A BUTTON TO CAST https://admin:[email protected]/* */:[email protected]/* */[email protected]/* */Dhttp://dmm.company.com:8080/etv-flash-webapp/app/etv_24_.htm%22 ** Use the Following MIB to see the NEW CONFIGURED Remote Mappings https://admin:[email protected]/* */:7777/get_param?p=*.*&init.pop_enable=false ** Save NEW CONFIGURED Remote Mappings on DMP    -> Use the ADVANCED TASK to SAVE the DMP Settings.    -> or Directly on the DMP using the DMP-DM Web Admin    -> or HTTP MIB          ie.          https://admin:[email protected]/* */:7777/set_param?mib.save=1          https://admin:[email protected]/* */:7777/set_param?mib.save=1&mng.reboot=1 

• using the remote control of the DVD does not select the correct buttons?

  Hey Ya'll,

  Project is almost complete, but I ran into one, which I think is a very simple problem...

  On my main menu, I have a total of 5 buttons on 2 rows.

  Line 1 to 2 buttons and Row 2 has 3 buttons.

  The links are correct, because they work fine in preview mode, using the mouse, but also view the version on the pc using Cyberlink DVD Viewer, once again, using the mouse to select the button.

  The problem is when you use the remote control, either on the copy engraved in the DVD player, or in preview mode, if I use the directional buttons of remote controls, that he does not want to go to the buttons I suppose it must

  (Top row left to right, then down row from left to right)

  On each of the properties of the buttons Panel, I chose the right (I guess) option number (just below name) for each button... IE top left set the right value top of page 1, 2, bottom left 3, the middle value 4 downstairs and down to the right the value 5.

  Type is set to Normal, the button name and Synch text is checked (although the No button is real, each is just a Word text, in photoshop, when I did originally the menu..)

  Also the low middle button never gets selected with the remote control of the DVD... Preview, using the buttons on the remote control, he finally gets selected, but it takes a bit of comes and goes, and the highlighted button is rarely what you would expect, since direction button your pushing.

  #1 button (top left) is set to the default button, which I want, but do not know how I set that, unless it's because it was the first button, I myself made/converted to the button)

  Here, any help would be greatly appreciated... that should finish this project!

  CB

  Cowboy Bob,

  No, what you did with the binder is actually linking these buttons to the assets.

  It shows a Menu with several buttons, icon manually road buttons depressed. Once you choose manually the buttons of road, they can change exactly what will make the remote control.

  

  As said, when you create a Menu, buttons start at # 1 and progress upward. Each Layer Set button plus up in the Layers Palette. This is the routing of the buttons Auto gets its information and it usually works. However, if you move the buttons around, removes some, etc., the en can get confused, manually their routing is the best way to go.

  Good luck and we hope this helps,

  Hunt

• The remote control comes charged out of the box or it must first charged?

  The remote control comes charged out of the box or it must first charged?

  It is usually quite busy, mine was about 85% when he arrived. It's a question about the pre purchase or you have a problem with your remote control works not.

• Toshiba 40RL953B has stopped responding to the remote control

  Hi all, my first post and this is a problem.
  I have a 3 years 40RL953B Toshiba tv that is not responding more to the remote and the buttons on the side, it is stuck on HDMI 2 port and works well with deviced plugged which, but I have no control of volume or something else.
  I was wondering if replacing the main Board it would heal or there at - it another way?
  The closest Toshiba repair center is 45 miles away and I don't want to spend a fortune on a 3 yr old TV that does not have the quality of great pic of anyway, but still, I don't want to just Chuck... 4
  Thanks in advance

  Hi all, I have a 40RL953B Toshiba 3 yr old 40 "Smart TV TNT HD, the problem is that he is stuck on HDMI 2 port and will not respond to the remote control or the buttons on the side. It does not work with something plugged into HDMI 2 but I have no volume control, it's ok when woking with a set-top box with no nut no good with the likes of a stick of fire from Amazon.
  What is a defect of the main card? Or y at - there a way to reset the system?
  Thanks in advance

• HP Compaq 8000 Elite SFF: Some HP Windows Media Center buttons on the remote control does not

  I have a desktop PC HP Compaq 8000 Elite SFF that I use as a home theater PC.  I'm under Windows Media Center with 2 cards tuner and antennae of the OTA.

  With this configuration, I use a HP Remote WMC.  The model No. inside the cover of the remote control battery is TSGH-IR01.  The issue I'm having with the remote control that is stationary and move forward and "back" button do nothing when you press.  The light at the top of the remote control flashes when you press those buttons, so I don't think that the buttons themselves infrared are failing.  All the other buttons on the remote work fine.

  I wonder if it is a problem of programming/software and if so, what should I do to solve this problem.   It's annoying to not be able to stop a recorded program is playing when you press the stop button, but having to use a mouse to do it instead.   Any help that can be given will be very appreciated!

  PainedByTech wrote:
  

  I have a desktop PC HP Compaq 8000 Elite SFF that I use as a home theater PC.  I'm under Windows Media Center with 2 cards tuner and antennae of the OTA.

  With this configuration, I use a HP Remote WMC.  The model No. inside the cover of the remote control battery is TSGH-IR01.  The issue I'm having with the remote control that is stationary and move forward and "back" button do nothing when you press.  The light at the top of the remote control flashes when you press those buttons, so I don't think that the buttons themselves infrared are failing.  All the other buttons on the remote work fine.

  I wonder if it is a problem of programming/software and if so, what should I do to solve this problem.   It's annoying to not be able to stop a recorded program is playing when you press the stop button, but having to use a mouse to do it instead.   Any help that can be given will be very appreciated!

  For anyone having this problem, I discovered the cause after reading a post on the forums of thegreenbutton.tv.  An application in Chrome or any browser Chrome (in my case, the Slimjet browser) is the culprit.

  For me, it was the Plex app.  He was diverting the judgment and move forward and back buttons on my remote HP WMC.  As soon as I disabled the application of Plex, the buttons started working.   Never would have guessed that this was the problem!  Hope this helps someone else who might have the same problem.  Ah, tech.  Isn't beautiful?

• long-lasting problems after windows scammersr had remote control of PC

  I got Asian male phone call to the effect that I had serious problems with a virus on my computer. He claimed to be the appeal on behalf of Microsoft Windows. Is not not in computer, I followed a number of directions to him which eventually led to him have the remote control of my computer. The number of callers evil disguised alarm of "oh my God" etc the alleged problems he has discovered and when the purpose of the payment was raised, I ended the call. The call lasted about 40 minutes, and he had the remote for about 5 minutes. It seemed to me that it was associated with a site named PC technocrat. My fear is now that he can have some future remote access or caused other problems that I have not yet thought.

  Unfortunately, once you give someone the remote control of your PC, they can do whatever they want.  There is no way for you to know what they did or did not.  You must assume the worst - they left behind software that allows them to take control of your system and/or take all the information they want it without your knowledge, and that they took any information they wanted while being connected.  Then contact the banks and other institutions in finaicial you do business with and take steps to protect your accounts and your credit cards.  Next would be to save only essential or element files and documents such as photos, music, etc and then destroy your computer and restore to factory new.

• Cannot get Windows Media Center to learn the remote control codes decoder

  I'm trying to put in place my TV card in Windows Media Center in Windows 7.  The card is a Hauppauge HVR 2250, which has a blaster/IR receiver.

  The configuration of the set-top box tells me to point the remote at the receiver and "hold" the number 0.  The problem is that the remote control supplied with the set-top box (Motorola RG2400) is not constantly emits the same IR signal when I press and hold the button - signal IR lasts only about a year and a half seconds before turning off. This does not seem to be sufficiently long for Windows Media Center and never detects the signal.

  Can I make it work?

  Hello

  Looks like the remote is faulty I recommend you do replace from the cable/satellite for a replacement/repair provider.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error step 7, creation of WebCenter, and schemas content using the remote control

  Hi all

  I have the installation of the portal WebCenter using JSK, but the failure of the process when it tries to create patterns using the remote, it shows "Time out when connecting to the database. The current values expires 30 seconds. "UCR-6090: jump main operation: validation stage of connection failure.

  This is the content of install_setup.log

  Thu Aug 14 10:12:32 CLT 2014: END STEP 6 22: Configurion of the database Instance

  Thu Aug 14 10:12:32 CLT 2014: START STEP 7 22: creation of the WebCenter and patterns content using the remote control. Estimated time is 1 minute. Please wait..

  localhost.localdomain:1521:ORCL

  Installation of patterns Begin spaces

  Please enter the password(User:sys) of the database:

  Processing of command line...

  Timeout connecting to the database. Current timeout value is 30 seconds.

  UCR-6090: jump main operation: validation step connection failure

  And the rcu.log

  14-08-2014 10:14:38.925 NOTIFICATION rcu: oracle.sysman.assistants.rcu.backend.RCUCommandLineParser::process: processing command line...

  14-08-2014 10:14:38.927 NOTIFICATION rcu: oracle.sysman.assistants.rcu.backend.SilentRCUModel::performOperation: from validations...

  14-08-2014 10:14:38.934 NOTIFICATION rcu: oracle.sysman.assistants.common.dbutil.jdbc.JDBCEngine::connect: the connection to the database: user: sys, role: sysdba, connectString: (description = (address = (host = localhost.localdomain)(protocol=tcp) (port = 1521)) (connect_data = (service_name = ORCL) (server = dedicated)))

  14-08-2014 10:15:39.250 rcu ERROR: oracle.sysman.assistants.rcu.backend.validation.StepValidator::isConnectionStepValidated: unable to connect to database: timeout when connecting to the database. Current timeout value is 30 seconds.

  14-08-2014 10:15:39.250 NOTIFICATION rcu: oracle.sysman.assistants.common.dbutil.jdbc.JDBCEngine::connect: the connection to the database: user: sys, role: sysdba, connectString: (description = (address = (host = localhost.localdomain)(protocol=tcp) (port = 1521)) (connect_data = (sid = ORCL) (server = dedicated)))

  14-08-2014 10:16:39.192 NOTIFICATION rcu: oracle.sysman.assistants.common.util.SilentMessageHandler::writeToLog: timeout when connecting to the database. Current timeout value is 30 seconds.

  14-08-2014 10:16:39.192 rcu ERROR: oracle.sysman.assistants.rcu.backend.validation.StepValidator::isConnectionStepValidated: SQLFatalErrorException:

  oracle.sysman.assistants.common.dbutil.SQLFatalErrorException: timeout when connecting to the database. Current timeout value is 30 seconds.

  at oracle.sysman.assistants.common.dbutil.jdbc.JDBCEngine.connect(JDBCEngine.java:585)

  at oracle.sysman.assistants.rcu.backend.validation.StepValidator.connectDatabase(StepValidator.java:358)

  at oracle.sysman.assistants.rcu.backend.validation.StepValidator.connectDatabase(StepValidator.java:253)

  at oracle.sysman.assistants.rcu.backend.validation.StepValidator.isConnectionStepValidated(StepValidator.java:1366)

  at oracle.sysman.assistants.rcu.backend.SilentRCUModel.performOperation(SilentRCUModel.java:140)

  at oracle.sysman.assistants.rcu.backend.RCUModel.startOperation(RCUModel.java:346)

  at oracle.sysman.assistants.rcu.Rcu.execute(Rcu.java:339)

  at oracle.sysman.assistants.rcu.Rcu.main(Rcu.java:363)

  2014-08-14 10:16:39.193 rcu ERROR: oracle.sysman.assistants.rcu.backend.SilentRCUModel::performOperation: UCR-6090: operation hand jump: validation step connection failure

  2014-08-14 10:16:39.193 NOTIFICATION rcu: oracle.sysman.assistants.common.util.SilentMessageHandler::writeToLog: UCR-6090: operation hand jump: validation step connection failure

  Any suggestions?

  Best regards!

  Hello

  (1) you see no error on the Setup screen? If Yes please download the screenshot?

  (2) the UCR is a failure because it is not able to connect to the database. Please make sure that you have entered the correct database details.

  Also, can you please try the following and check the box.

  Go to the location / / rcu/config /

  Take backup for the file rcu.properties, and then change the below

  JDBC_LOGIN_TIMEOUT = 30

  TO

  JDBC_LOGIN_TIMEOUT = 300

  and try again.

  Concerning

  Françoise

• Installation of OBIEE without using the remote control.

  Hello
  

  
  

  I installs le OBIEE et will use the Oracle database, but will not use the RCU. I wonder if I need of some pre -requisite to create the schema?

  
  Is there any documentation with installation create RCU schemas without?

  
  

  Thank you.
  

  Hello

  Without the remote control will not work OBIEE 11g because the remote control allows you to install certain patterns in a database that are required by median Fusion as Oracle BI EE ware products. These schemas can be installed on any certified version of database such as Oracle, Microsoft SQL Server, or IBM DB2 database. There are patterns that are required by the main components of Oracle Fusion Middleware, although there are Oracle BI EE patterns requires, as the Planner, BI Publisher, for the new product of the scorecard.

  Note: You can install it without the remote, but we must approach below.

  SATYA RANKI OBIEE REDDY SOLUTIONS: How to install OBIEE 11 g without the remote

  Thank you

  Satya Reddy Ranki

• How to stop the remote control to the setting

  How to stop the remote control to the setting

  Disable the settings > general > accessibility > voiceover.

• For the remote controls of the Keynote?

  I want to use a remote control for a presentation in Keynote, I'll give.  It will be my first with a remote control, but which is later - should I buy a (If Yes, who?) or what is the last and the best app for me to use my iPhone as a remote control (which I prefer, a gadget to lose less!)?

  Please use a simple language with me, a digital native.

  I use my aging MacBook Pro with OSX 10.7.5, my speech is 5.1.1 and my iPhone is a 6s.

  Thank you!

  Using a method rather than another is a personal preference, my preference as a coach and lecturer working in several different locations is to use Keynote for iOS, it has built in the remote control feature:

  Tap to go to the next slide

  previous slide scanning

  Pen tool marker on the screen

  the highlighter to screen

  the iPad displays the screen of the presenter, showing the next slide and notes of the speaker of the presentation on the Mac

  

  There must be a wifi network present, you can connect; many businesses teaching institutions lock unregistered users by default

  The site Web of Keynote iOS is here: Keynote for iOS

• How to recharge the remote control for Apple TV 4

  How to recharge the remote control for Apple TV 4

  Recharge your Siri or Apple TV Remote - Support Apple Remote