Problem: EA 4500 do not connect one device

Similar Questions

• My HP 3 year all-in-one C4280 shows USB not connected and "device not detected.

  Everything works OK until a few weeks ago. I uninstalled reinstalled. During the installation, there is a message' device detected"and then at the end of"device not found ".

  Also USB not connected. Switched USB to another port, nothing helps. Contacted HP.com.I running Vista Home Premium SP2. This is my last ditch attempt to resolve. Is this a problem with Vista?

  Hello

  I suggest you try to run the Microsoft Fixit from this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  It will be useful.

• HP Officejet 4500: HP Officejet 4500 suddenly "not connected" and wants to "fax" while trying to print

  After last version 10 of Windows set to update my HP Officejet 4500, which was working fine, now it is "not connected", says or wants to "fax"everything." Can not even uninstall printer to reinstall the drivers. Where should I start to fix this mess?

  I managed to successfully uninstall printer with control panel and Device Manager. I then downloaded latest drivers from HP specifically say it's for Windows 10.     support.hp.com/gb-en/product/HP-Officejet-4500-All-in-One-Printer-Series---G5/3919445/model/3919446/drivers I installed and wonderful - printer working properly again. He does not think it is only a fax and print again normally computer. I think the drivers HP takes over again and did not allow 10 Windows run the show and confuse the printer and the computer more!

  Milo5

• New HP Envy 4500 will not connect with my computer

  New HP printer shows blue light of connection with my wireless network but the printer connects with my computer (Windows 7 64-bit)

  I tried troubleshooting with doctor without success.  I thought about the restoration to the manufacturer's specifications. but worried about this procedure.

  Confused.

  Help please

  Adnilybrek28

  Welcome to the HP Forum.

  There is lots of useful information to the Web site of your printer.  In addition, the most important thing you can do is to install the full features software for your printer.  The installation process should help you with the login process.

  General instructions to install the printer software

  • Create a Restore Point: create a restore - Win7 Point OR create a restore point Win8
  • Open drivers HP & downloads
  • Enter your printer model information
  • Select your printer in the list of the 'results '.

  OR

  • Open of printer drivers HP ENVY 4500 e-all-in-one
  • Enter your operating system from the menu drop-down
  • Click NEXT and scroll down
  • Find the category driver - software product installation
  • Select the base driver, e-print, or a full features software
  • Save the *.exe installation package (s) on your computer

  The files will probably save in the "folder"downloads. "

  If it is available, you can download print and scan doctor and / or other programs of the category-utilities

  TIP:

  Install the utilities / tools first. bit installation packages are smaller in size

  • If you have control of "Admin", you can highlight the package and "double-click" to install it, otherwise just right-click, select run as administrator and install.

  NOTES:

  •         Look at the bottom half of the main Web page for your printer for helpful videos help with the installation of the printer software!
  •         Scroll through the list of videos back until you find the video that best fits your situation.
  • Connection USB: download and install the driver software before connecting a USB cable.
  • Ethernet: connect the printer to the network and (optional) assign the printer IP address to the router. Once the printer is connected to the network, make sure that the printer is on, and then install the printer software.
  • Once the initial installation is complete and functional, check / install category - updated

  There is valuable information about the Web site, including Manual, pages How-to's , Troubleshooting and SOLUTIONS section and alerts and notifications for your printer.  Be sure to take a comprehensive look at what's available.  To bookmark the page.

  Click on the Thumbs-Up Kudos to show that you appreciate the help and time of our Experts.

  Although I strive to reflect best practices of HP, I do not work for HP.

  When the answer is a good fix or workaround, click accept as Solution !

• After meeting a connection problem, the computer does not connect to the network through a wired connection or wireless

  Original title:

  I have HP laptop with Windows Vista, I recently met a connection problem. I can't connect to the wired or wireless network. I network is invisible and I want to go back to the old setting. Could you please tell me how to do this

  Hello

  1. What is the brand and model of the computer?

  2. what happens when you try to connect to the Internet?

  3. do you get an error message? If Yes, what is the exact error message?

  4. are you aware of any changes made to the computer, before the show?

  Method 1:

  Follow the instructions in the following link.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Update the NIC drivers and check the issue.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps.

• Problem using lightroom is not connected to the internet

  I have a subscription to that pay annually.  In the past I could use lightroom (and first pro) even when I was not connected to the internet (I live on a sailboat trip.)   Now he continues to wonder 'trail or subscription' and when I say subscription it say "Internet connection required. If please connect to internet and select retry. "It will be a problem when I'm going to be out of reach of the internet for 4 weeks next month.

  The CC is active, please refer to:

  Creative Cloud applications unexpectedly back in the test mode. CCM, CS6

  https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html

  Concerning

  Stéphane

• 12.3.3.17 iTunes could not connect to devices AirPlay (Airport Express)

  After the update to iTunes 12.3.3.17 I can connect is more to Apple Airport Express.

  I updated iTunes to 12.3.3.17 on both computers:

  1. Windows 7 64-bit SP1 / iTunes 12.3.3.17 64-bit

  2 Windows 10 64 - bit / iTunes 12.3.3.17 64-bit

  On the Windows 10 computer, iTunes can connect and play all three Airport Express.  An iPod Touch can also flow to each of them.

  After the upgrade to 12.3.3.17 on the Windows 7 SP1 computer, iTunes can see all three Airport Express and they are not greyed out.  But when an any of them are selected in the dialog of speaker, iTunes tries to connect and after 30 seconds results in the error "an error occurred when connecting to the device AirPlay"xxx". The network connection timed out' and the selection is then grayed out.

  The network card on this PC, the router, and all three Airport Express everything seems to work properly as I can deliver on all of them using software third 'wing' with other applications as the source.  I can also control iTunes on the PC wirelessly from iPod with the Remote app.

  I just can no longer spread to one of the Express from the airport directly from iTunes after the 12.3.3.17 update.

  Any thoughts?

  Well, problem solved (mostly) by a lot of trial and error and it turns out be a problem of WF on the UDP ports must be open for Hello.  It was a bit of a surprise, because the Airfoil program (third party utility AirPlay) uses also Hello (that works).

  The Windows Firewall has a rule entry of inbound traffic for Hello to port 5353 UDP.  Changing the rule to allow all Ports (UDP) does the job.  So I studied what UDP ports were actually necessary for the Hello and Airplay and amended the rule again, this time replacing all Ports with these specific UDP port numbers: 554 (1900), 5289 5298, 5350, 5351, 5353, 49159, 49163

  However, that did not yet work so I ended up coming back to the all Ports configuration.

  If someone uses the firewall native Windows (preferably Windows 7, but probably the same for 8 and 10), I would be interested to know what UDP ports allows your Windows Hello firewall.

  Control Panel > Windows Firewall > advanced settings > inbound rules > Hello

  I had certainly not changed firewall settings before this update to iTunes (and AirPlay worked just hours before) and know not why the update seems to have changed the Windows Firewall settings, but that helps to explain why the Windows 10 computer worked fine after the update, because she was using the McAfee Security Suite firewall.

  Thank you!

• 4620 does not connect with devices

  My 4620 ceased to connect to one of my devices. We have 2 MacBook, iPad and iPhone 2 5 s that all used to work. All devices are connected to my wifi network as is the 4620, but I can not print on any of them. 4620 HP Network Configuration report shows the signal strength of 5, connected to channel 8, nearest neighbour SSID channel 11.

  I had intermittent problems with printing but can usually operate by closing the wifi on printer and reconnect or sometimes after he tried to connect for an hour or more, suddenly it prints.

  Help!

  Hello smfinga,

  I understand your HP OfficeJet 4620 is no longer able to connect all the devices, and you are not able to print wireless. How many devices are currently connected to your router? You can have many devices connected to a router, which can be the cause of error. Let me know which operating system you are using?

  I would like you to a hard reset on your wireless network, follow the steps below:

  1. unplug the router, the printer and the Mac in that order, abandon for at least 5 minutes, make sure that all devices are disconnected from your network. (Please leave all of the other devices power off to it)

  2. now, let's go and turn on the router first wait until it is running, now, turn on the JO 4620 let him completely initialized. Let's turn on the Mac.

  3. now try to print, please take note of any errors that you may encounter.

  4. If the documents are not yet print Please run HP print and Scan Doctor- designed by HP to offer users the features and troubleshooting problem needed to solve many common problems experienced with HP print and scan the products related to Windows computers.

  Let me know if this solves the problem, if you are now able to print. If you still have problems of response returns with the requested information.

  Thank you

• Can not connect 2 devices with creative cloud

  Hi, I have a creative cloud account and have problems to connect the two devices with the same account.

  Normally, I should not have questions this.

  On the first device works perfectly. But when I connect from the second device (I disconnect from the first), I get only trial versions of apps, some of them has expired and I can't verify license.

  'No subscription found' message. But on the applications tab, all the applications are installed.

  I don't see what the problem is.

  The management of accounts, I see I have two devices

  You should not have to log out or if it's just two devices.  A subscription allows having two devices signed in at the same time.

  FAQ: What should I do if I have a subscription, but my application acts as if I had a trial?

  https://forums.Adobe.com/thread/1962238

  Creative Cloud applications unexpectedly back in the test mode. CS6, CCM

  https://helpx.Adobe.com/Creative-Suite/KB/trial--1-launch.html

• HP Envy 4500: Could not connect to connected HP - get 'Email or invalid password'

  When I try to connect to connected HP, I get "Email and password invalid".  The email and password I use works fine to Snapfish.  I tried to change the password to Snapfish, hoping that would reset the password in HP connected, but I still get the same message there.  How can I get my HP account connected?

  Thank you

  This problem is finally resolved.  Eventually be reassigned to Cloud Services L2 support team.  Apparently when I converted initially more than HP ePrintCenter attached, something went wrong, which left my HP account logged in a bad state or something.  The result was that, while I was able to connect to ePrintCenter and then click HP connected, when I tried to connect to HP connected directly, I got the problems identified above.

  They managed to get things fixed to the top, and now I am able to connect to HP directly connected.

  See you soon,.

  Sandra

• LAN problem: Vista PC does not connect to the XP PC through a router

  My setup: laptop XP SP3, laptop Vista Home premium SP1, Fritz! Box 7270 as ADSL Modem, router and gateway.

  Since the Installation of the SP3 on XP laptop PC Vista can no longer access the XP PC. Vista indicates the XP Machine occasionally, but cannot connect. Error 0 x 80070035. Ping from Vista to XP translates to time limit.

  XP PC can connect to the Vista PC and use all the services available.

  I am a user experienced with the good network of expertise. I checked the configuration settings and tested alternative parameters. I installed KB 922120V6-x86D DTBT Protocol on the XP PC. No change in the behavior of the network.

  Internet connection through the gateway works fine on both machines.

  Useful tips are very much appreciated

  Karl

  You have probably two firewalls running on XP is the first place to check. If you have a software firewall or antivirus/security of the third party with its own firewall component, the built-in Windows Firewall should not be running and it probably is. Or are looking for a firewall neglected in the VPN software if you use it. MS - MVP - Elephant Boy computers - don't panic!

• does not install the USB MTP device driver. I can not connect external devices such as the Samsung Galaxy. I tried several uninstall and re - install, no solution

  I tried in the manner suggested in many forums, nothing worked. in fact when I forst connected you Galaxy it worked for a few days, then it stopped. My company ha installed on my PC System Center 2012 Endpoint Protection; However, it is there even when I was able to connect.  I have also the ipad tird and I get the same error.

  the solution to my previous request on the same subject by Rob Thomas596 strictly relates to Apple products and I can't use it for the Galaxy

  Run as administrator command prompt and run the following command:

  NET local service localgroup administrators / add

  This is what fixed my problem after searching everywhere

• OfficeJet 4500 does not connect to the network

  My officejet 4500 works perfectly until I have change the wireless network modem. USB connection is fine. Windows 7.  When I reinstall I don't get the option of wireless connection.

  Hi dperk8,

  Check out the video below to connect the printer to your network by using the control panel.

• THE SPEAKERS INTERNAL, DESCRIPTION OF THE PROBLEM HAVE SAID POINT NOT CONNECTED

  I internal speakers "speaker" icon has X through it click on the message says speakers not plugged

  Hello

  1. All changes made to the computer before the show?
  2. What brand / model of the computer?
   
  Try the methods provided a check if the issue is resolved.
   
  Method 1:
  Check the link and try the tips in the article.
  Tips for solving common audio problems
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems
   
  Method 2:
  Check the link and try the steps outlined in the article.
  No sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
   
  Method 3:
  To test your speaker configuration and make sure you get the best sound from your computer, follow these steps:
  a. Open Sound by clicking on the Start button, then Control Panel. In the search box, type sound, and then click sound.
  b. click on the playback tab, select your speakers, and then click Configure.
  c. Select your speaker configuration, and then click Test.

• I am using windows 7 pro that my Skype was working withou any problem now Skype would not connect and I got a message saying outside the system resourses help

  I use windows 7 Professional now my Skype was working with windows 7 Home premium, when I went to W 7 PRO, everything was ok he continue to work and that was three months ago now, this morning, it wouldn't connect and a window came to say that he's out of system resources, and I don't understand

  Try going back to when it worked.

  How to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista (or 7)
  http://support.Microsoft.com/kb/936212/#appliesTo

  You use the latest version of Skype?

  Technical issues & using Skype
  https://support.Skype.com/category/tech/;JSESSIONID=4E8285AB5B23BE17D96D57F0C021F032

  Alternatively, you can try the Skype Forum.
  http://community.Skype.com/T5/English/CT-p/English?profile.language=en

  Skype on system resources?
  http://community.Skype.com/T5/general-discussion/Skype-out-of-system-resources/TD-p/396509

  You can try to uninstall Skype and put it back.