Problem installing PCI-6220

Similar Questions

• Problem of current drawing of digital entry into PCI-6220

  We have card NI PCI-6220 mounted on card PCI-Raiser in a windows PC mini. We are using 8-channel digital input P1.4 - P1.7 and P2.2 - P2.5 to take a few entries of our entry card.

  When the computer is turned on then everything works well and we get of the digital inputs in Labview. The problem is that when the computer is off the digital inputs on current drawing of early card PCI-6220 and due to this voltage regulator IC on our card entry begins to heat upward.

  This problem occurs only when the PC is turned off, in a State that everything works fine.

  We will be grateful can anyone suggest a solution to our problem.

  Concerning

  Magalie

  I'm not familiar with this part OR special. But maybe there is protection on the output diodes. Usually, these diodes are connected since the entries on the power rail.

  In case the power rail is 0V (or below the input voltage supplied in them), the LEDs will be put and feeding current in the power of the PC rail, attractive and current of your external device. If this unit has a push-pull, HIGH level output configuration there will be excessive current from the power supply where the outputs are short-circuit or almost short as it will be in the configuration described above.

  I have no immediate solution except for additional hardware as the optocouplers, the outputs of your device from the inputs of the unit NOR the decoupling.

• Problem with PCI-4065

  Nice day

  Install dmm multimeter 3.0.6f1 version and when I install PCI-4060 and PCI-4065, max (measurement & automation explorer) detect PCI-4060, but PCI-4065, before this failure had not

  Thomas, Jared thank you for for your support!

  Ago corregi el problema... lo that achieve fue than baje ultima version of NI-DAQ (NI DAQ 9.7.0) the instale, reset the computadora y al iniciar shelter MAX y ago detecta las tarjetas PCI-4065...

  SALUDOS!

• Replace PCI-6220 PCIe-6320?

  New to the forum, so bear with me if I'm in the wrong place.

  I have a system with a card PCI-6220, and I am considering the upgrade of the computer used. If I decide to do, then I would like to upgrade the jury as well. According to the information of product of NOR, the PCI-6220 can be replaced by PCIe-6320. I am concerned by the mapping of the e/s on the same map if and I was wondering if anyone else has had experience with this. I need to know if I should change the LabView code to accommodate the new Board of Directors, or if a replacement that will work only.

  Thank you!

  WisDave wrote:

  Since the list of pins of the two boards are the same, you expect that there is problems with the interaction with the SC-2345?

  Not at all.  NEITHER tends to keep things mostly the same between boards so that they can reuse the connection blocks.

• install PCI device driver

  I have a HP laptop, 655 and I have a problem installing the Device PCI driver, although I tried to update I couldn't do. Please help me.

  Hello:

  The support Center Web site business seems to be down at the moment.

  You need the Realtek card reader driver to install the PCI device.

  As an alternative, you can download the first driver on the list on the link below:

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownTypeID=3&GETDOWN=false

• TC M51 sluggish after installed PCIe graphics card

  Well I went through 10 the 39 pages of this forum and the suspect, I have an answer, but still want to check with anyone in the know.

  I have a model of ThinkCentre M51 1843-wnv and put up-to-date with:

  2 GB DDR RAM (total now 2.5 GB) by Kingston

  WD Caviar Black 500 GB HARD drive with 32 MB of cache (SATA 7200 RPM)

  Map of graph SAPPHIRE Radeon HD 4550 PCIe with 512 MB of DDR3 RAM

  and I use a logitech (with USB to PS/2 adapter) USB mouse and a USB microsoft ergonomic keyboard

  I installed every update, one at a time to make sure things were ok.  Things were ok until I installed the GPU (last updated).  Now my system takes a long time to start and stop and the intermittent mouse jerks across the screen.  I wait a few seconds and he is well again.  It's as if there are not sufficient resources every now and then.  For a time that the office works very well and then a few minutes later he has a jerky behavior that erases then after a wait.  Start and stop are however still much longer than they were.  I have to go and make the coffee while it starts and stops.  But even this behavior is inconsistent.  Sometimes it starts and stops quickly, as it should.

  I wonder if the GPU and HARD disk are pushing the limits of my diet (310 watts).  Side of the box GPU stipulates that the minimum requirement is a 300 Watt power supply.  Mine is 310 Watts so I thought I was good, but the desktop is perhaps, with the large disc of HARD fast intermittently requiring more power than is available.

  Any thoughts?

  Is an upgrade of the power source easy to do something?  This will solve the performance issue? I've updated GPU, RAM, hard drives, USB and card faxmodem cards.  An upgrade of the power source is easy?

  Thank you!

  Macaws

  Well, how does it work!

  I uninstalled the sound integrated edge and also the SoundMax drivers and installed instead an his SB XFi Titanium PCIe card and voila!  not only do you have this problem, but I have now improved for my 5.1 system sound quality speakers.

  Why the built-in sound system would cause my office become slow after installing a video card?  How install PCIe sound card and turning off the sound of the mobo solves the problem?

  If anyone knows I really want to know how it works.  At the moment, it seems just as if by magic for me.

  in any case, I'm very happy.  My 2nd hand desktop Lenovo is a speed demon!  Movhorn thanks for your help.  Very much appreciated.

• Problem installing device a1530n

  Running Win XP Media Center Edition.  Had minor graphical problems at the top of the IE bar periodically endangered.  Decided to remove the Intel (r) 82945G Express Chipset adapter in Device Manager and then do a scan for new hardware.  And now I get the message of the new hardware detected that says.

  Cannot install this hardware

  There was a problem installing this hardware:

  Intel (r) 82945G Express Chipset Family

  An error occurred during the installation of the device

  Access is denied.

  I am connected to the computer as an administrator.  I tried to install this even in safe mode and get the same error above.  Any clues on what do I do?  The computer runs only in VGA mode.

  Thanks in advance.

  Link to screen shot of the error message.

• Satellite P300-133 - problem installing Win Xp

  Hello

  I have a problem installing win xp to Satellite p300-133.
  To resolve this problem, I have tried the solutions:
  switch to ahci mode in bios and incorporating storage drivers compatibility intel to the installation cd xp with nlite, but none of them solved the problem.

  Laptop computer starts from the cd of xp and xp installation says "program Setup inspects your hardware configuration" and then a blank black screen comes.
  After that, the installation does nothing and waits indefinitely.

  Any ideas on this problem? Thank you.

  Hello

  > switch to compatibility ahci mode in the bios and the integration of the storage drivers Intel to xp with nlite installation cd, but none of them solved the problem.

  The two methods are good!
  You can install the Win XP without drivers Intel Storage Manager (SATA drivers) but in this case the SATA mode must be on compatible mode.
  It works for sure!

  The second method is the installation of the SATA drivers with nLite (drivers can be integrated into the new drive Win XP).

  I put t understand why this doesn t work on your laptop. I think it's a problem with your Win XP drive. Contains this Win XP SP2 or SP3?
  If this isn't the case, then you should use nLite to include min the Win XP SP2.

  Check it!

• Problem installing LAN USB adapter in a new copy of windows 2000

  After having reformatted my hard drive and install a new copy of window 2000, I'm having a problem installing device drivers.  When I enter the correct inf file path, it reports that this window has not found a driver for the device.  Whithout the possibility to connect to internet, I have exhausted all my options and still need to install several other drivers with the same problem.  help help help help

  Everything you try to use (you do not give the brand / model of the LAN USB adapter) made drivers for Windows 2000?

• Problem installing Webroot for MSN (part of the Internet software of MSN Premium subscription) "error 5: access is denied" and "Setup could not create the directory"C:; Program Files/Webroot/security /...

  Original title: problem installing Webroot for MSN (part of the Internet software of MSN Premium subscription)

  Try installing Webroot to MSN but when I run the installer, I get "error 5: access is denied" and "Setup could not create the directory"C:; Program Files/Webroot/security/current/plugins/antimalware/Backup ". OS is XP with Service Pack 3. I tried to delete my existing Webroot program and turning to the bottom/off other security options... Any suggestions? Thank you.

  Thanks for the reply. I was able to finally get the new Webroot program to install after running a Microsoft Fix affecting the directory uninstall the old prgm Webroot and meets a new error code (1603), which led me to this site to permissions Grant full control to the SYSTEM account.

  http://support.Microsoft.com/kb/834484

• IPod Classic 7 G 160 GB ' there was a problem installing this hardware: Apple iPod USB Device ".

  I have recently (June 2014) bought a brand new Ipod Classic 7 G 160 GB Model A1238.

  Whenever I connect via USB to a PC running XP SP3 and Itunes V10.0.7.2 it is always treated as if it were a new connection, i.e. "new hardware found". After trying to install it, it says so "cannot install this hardware" and "there was a problem installing this hardware: Apple iPod USB Device."
  I have also a 2009 16 GB Ipod Nano 4 G model 1285 and this is recognized by the PC whenever it is connected through the USB port itself.
  I connected the Ipod Classic 7 G to a laptop running Vista and Itunes V10.0.7.2 where the Ipod is recognized and installed.

  Even if the PC States that there is a problem installing the Ipod, it still appears in Itunes and I can download music to it and disconnect by using safe mode disconnect.

  PC XP SP3 - Ipod Classic
  I watched "Device Manager" under "Drives", the Ipod Classic is listed as an "Apple Ipod USB Device", but has an exclanation score against it.

  Right-click on the 'Apple Ipod USB Device' properties and the "Volumes" tab it shows the drive with the exact name and the size of the data, by clicking on the properties of "Driver" tab it says 'Unknown' driver provider, driver Date and Driver Version as being "not available". By clicking on the "Driver Details" properties, it shows a driver file-

  C:\WINDOWS\system32\drivers\PartMgr.sys, File Version 5.1.2600.5512 (xpsp080413-2108).

  Under "Device Manager" USB controllers, there is an entry for "Apple Mobile Devices USB Driver" and a "USb Mass Storage Device"

  The 'Apple Mobile Devices USB Driver' lists two drivers:
  C:\WINDOWS\System32\Drivers\usbaapl.sys and
  C:\WINDOWS\System32\usbaaplrc.sys

  The "USB Mass Storage Device" list a driver:
  C:\WINDOWS\System32\Drivers\USBSTOR. SYS

  PC XP SP3 - Ipod Nano

  I repeated the steps above with the Ipod Nano, connected to the PC and the driver provider is presented as Microsoft with the driver as 07/01/01 Date and Version of the driver as 5.1.2535.0.
  In the "Driver Details" properties, it shows TWO driver files:

  C:\WINDOWS\system32\DRIVERS\disk.sys AND meanings
  C:\WINDOWS\system32\drivers\PartMgr.sys.
  At the same time with the Version of the file 5.1.2600.5512 (xpsp080413-2108).

  The 'Apple Mobile Devices USB Driver' and "USB Mass Storage Device" are the same as for the Ipod Classic.

  I followed the procedure to remove Itunes and even the update to Itunes to V11.2.2 nothing works.

  I am aware that the system is also that XP can now be updated.

  So, why not not Windows Installer Ipod Classic and why the disk.sys driver does not appear

  According to the details of the pilot?

  Is the 7 G Ipod Classic not compatible with XP SP3?

  Yes it is compatible with XP SP3.

  Try asking in the forums of Apple iPod:

  https://discussions.Apple.com/community/iPod/ipod_classic?CategoryID=204

• Problem installing disktop 800 wireless drivers for windows xp

  Problem installing disktop 800 wireless drivers for windows xp

  Hi Samir,

  I see that you are unable to install the drivers disktop 800 wireless. I'll help you with this problem.

  1. What is the brand and model of the computer?

  2. what security software is installed on the computer?

  3. have you made changes on the computer recently?

  4. What is the error you get when trying to install the driver?

  Please provide us with more information to continue troubleshooting as a result.

  See the link on how to ask questions or help on the Forums.

  Suggestions for a question on help forums: http://support.microsoft.com/kb/555375

  Refer.

  Wireless and wired network problems: http://windows.microsoft.com/en-US/windows/network-connection-problem-help#network-problems=windows-xp&v1h=win8tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• When you try to install the HP Laserjet 1300 printer error there is a problem installing this hardware.

  Original title: HP Laserjet 1300 Windows XP, SP3 error installation

  When you try to install the HP Laserjet 1300 printer, I get the following error message and the process stops and restores.

  CANNOT INSTALL THIS HARDWARE

  There was a problem installing this hardware

  HP Laserjet 1300 PCL 6

  An error occurred during the installation of the device.

  The specified Module could not be found.

  I have used the original printer installation cd, bought a new cd from HP and downloaded the drivers directly from the HP Web site and I get the same error.  The record show error install printer on each attempt of events. Can anyone help?  Thank you

  Hello

  You are able to install other programs?

   

  Method 1: See the following article:

   

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c02073861&LC=en&cc=us&product=3795406

   

  Method 2: view the following steps and see if that helps.

  (a) disconnect the printer

  (b) uninstall the software and drivers on the computer

  (c) plug the printer back

  (d) allow the Hardware Wizard search for drivers

  e) if it does not, it asks you to install the source for the drivers, the installation driver CD and install the drivers and see if that helps.

• Problem installing KB2728973 ' Unathorized digital certificates could allow spoofing "which was released 10JULY2012

  Has anyone had a problem installing KB2728973 ' Unathorized digital certificates could allow spoofing "which was released 10JULY2012?  I could not this patch to run after double-clicking on it.  This was true for XP SP3 and Server 2003 SP2.  Your comments are appreciated.  By-the-way, I met all three requirements that are suggested in the section "Known issues" section of Microsoft.

  Help us help you: start by reading this post 'sticky '...

  What information to post in the Windows Update forum
      http://answers.Microsoft.com/thread/1467f44b-ee27-4F7D-98d7-f1c4b35b3395

  ===========

  It is a forum for specific consumers. You will find the Windows Server support in these forums: http://social.technet.microsoft.com/Forums/en/category/windowsserver

• Problem installing HP Deskjet F2280 and Windows7

  Hi people,
  I have a problem installing my printer hp deskjet F2280 all-in-one printer. Its saying its compatible on the windows 7 and custom allow to be the command "run under...". ».  This printer is only 6 months old :(
  Anyone got around this problem yet?

  Thank you

  Hello SeaCos,

  Thank you for using the Microsoft Windows Vista Forums.

  If notifies you that it is not compatible with Windows 7, you need to contact HP support to see all the drivers compatible. Are you following the steps below to set up your printer? Please let us know status. Thank you!

  http://www.HP.com/SBSO/bussupport.html

  Windows 7 install a printer
  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

  Open devices and printers, click the Start button, and then click the start menu, click devices and printers.

  Click Add a printer. In the Add Printer Wizard, click Add a local printer. Choose a printer port page, make sure you use a button existing port and the recommended printer port are selected and then click Next.

  On the installation of the printer driver page, select the model and manufacturer of the printer, and then click Next.

  If your printer is not listed, click Windows Update, and then wait while Windows searches for drivers additional. If none is available and you have the installation CD, click disk, and then navigate to the folder where the printer driver. (For additional guidance, see the printer manual.) Perform the steps in the wizard and then click Finish.