Problem installing WAP54G in Repeater mode

Similar Questions

• WAP54G (v3.1) in Repeater Mode to WRT54G (v5) will not affect the IP via DHCP

  Hi, I just installed a WAP54G Access Point and define the AP as REPEATER mode.  I followed all the instructions, including the seizure of the MAC address of the router (WRT54G).  The signal seems to have substantially improved by the WAP in Repeater mode, but I can't connect to the wireless network as an IP is not able to attribute.  I tried different laptops running different wireless cards and get the same result.  Two (for WAP and the WRT) MAC addresses appear in the "monitor of the site" the utility of the wi - fi card (of course, WAP is the most powerful signal), but it fails when it tries to acquire a network address.  If I move the laptop closer to the WRT, assigns an IP address physically & I can connect, I just can't get the router to pass the IP address through repetition to the laptop.  I have updated the firmware on the two WRT & WAP.  No difference.

  Any help would be greatly appreciated!

  Ed Lefkowitz

  Montgomery County, Maryland Government

  Fred, you're a genius! Who did the trick!  Live and learn.  I had no idea there is more than one MAC on the WRT54G.  I appreciate your help.  Super Bravo to you.

  -Ed.

• WAP54G - Repeater mode

  Hi all!

  I tried to "repeat" a Lynksys WRT120N Router(ver. 1.0.01 G-mode only) using WAP54G Access Point(ver. 3.04) as repeaters. Is it possible in general because I had no luck so far?

  Thank you in advance!

  Momchil

  Well it is not possible to make your WAP54G work in Repeater with WRT120N router mode.  WAP54G will work only with the WRT54G Router Repeater mode.

• Problem installing XP Mode in Windows 7 Pro (64) SP1

  XP mode has been successfully installed, but does not have Virtual PC. I downloaded the correct file - Windows6. 1 - KB958559 - x 64 - RefreshPkg.msu - and when I try to install it I get this update is already installed on my computer - but Virtual PC does not. What now?

  Thanks for any advice that can be offered.
  SoC

  [Original installing KB958559] proved to be corrupt, while Virtual PC installed not [so I uninstalled then reinstalled KB958559] it.

  
  Source: https://social.technet.microsoft.com/Forums/windows/en-US/7275b2b5-29ef-4680-9f61-56b9a7457153/problem-installing-virtual-pc-for-xp-mode-in-win-7-pro64-sp1?forum=w7itprovirt

• Problem installing Windows XP Mode in 7 Winjdows

  I have a problem installing Windows XP Mode in Windows 7 Pro 64 running on a Dell Latitude E6510 laptop with an i5 processor and 8 GB of ram.  This machine supports hardware virtualization, and it is enabled in the BIOS.

  Before downloading software in XP Mode, the MS download required Windows validation Web site.  Downloaded and reported validation validation and a successful installation.  Then I downloaded Windows XP Mode (WindowsXPMode_en - us.exe, 481 052 KB) installation package and the package of Windows Virtual PC (Windows6 1 - KB958559 - x 64 - RefreshPkg.msu, 16 692-Ko).  Then, I installed Windows XP Mode; the installation ran without any problems apparent and reported success.
  According to the docs of download site, the next step is to: "... click on the Windows 7 start button , and then select all programs > Windows Virtual PC > Windows XP Mode to begin the installation."
  My problem is Windows Virtual PC does not appear anywhere in the selection of all programs list - believe me, I looked.  There is, however, a new directory called
  c:\ProgramFiles\Windows XP Mode\
  but it contains no exe file.  It contains a file of 1.2 GB called Windows XP Mode base.vhd - but it is not clear what to do with it.  There is also a tutorial subdirectory.
  I tried to reinstall Windows XP Mode (without uninstalling first) but I just get a warning message that the program is already installed.  Windows XP Mode appears on the list "Uninstall or change a program" in the module programs and features in Control Panel.
  I tried running (Windows6. 1-KB958559-x64-RefreshPkg.msu(Windows6.1-KB958559-x64-RefreshPkg.msu, goal that throws error 0x8007000d, "The data is invalid."
  If at this point, my question is simple, "what to try next?
  Thanks in advance.

  The right way to install Windows XP Mode, you must first install Windows Virtual PC, and then install Windows XP Mode.

  You must install both files:

  1 Windows6. 1 - KB958559 - x 64 or x 86 architecture that you run

  Restart the system, and then install:

  2 WindowsXPMode_en-we

  ------------

  Uninstall Windows XP Mode:

  Click Start, type: programs and features

  Press enter on your keyboard

  Scroll down

  Select Windows XP Mode

  Click Change/uninstall in the command bar

  Uninstall Windows XP Mode

  -----------------

  Restart your computer

  Proceed with the installation of Windows XP Mode in the right order.

  --------------

  If it does not always show upward:

  Click Start, type: enable or disable windows features

  Scroll down

  Make sure that Windows Virtual PC is checked

  Click OK

  Reboot if prompted

  -------------------

  http://www.notebooks.com/2009/11/23/using-Windows-Virtual-PC-with-Windows-XP-mode/

• WAP54G as Repeater. PC connected but no internet.

  router: WRT160N (v2)

  AP/Repeater: WAP54G (v3.1)

  firmware: updated

  First of all, I read that WAP54G is not listed to support WRT160n (didn't know up to this than purchased).

  Problem: I got the program to install my router and AP (now coach) as assumed.

  same channel

  same ssid

  same network mode

  same level of security (no current)

  A wireless laptop has been able to connect to the Repeater with 100% signal, but it cannot access the internet. He says "limited or no internet access" or something along the line.

  What I am doing wrong?

  It is connected but cannot access the internet? No idea why?

  Is my only option wap54g back?

  Goal: to connect my PS3 with 100% signal to my router wireless very far from another corner of the House.

  The only mode where the WAP54G expects no Ethernet connection is Repeater mode, all other modes can expect an Ethernet connection.

  Scenario a.

  WRT160N connected to a switch.

  WAP54G wired to the same nework as switch.

  Another WAP54G in mode (not wired) Repeater to extend the range.

  Scenario B

  WRT54GL (can be wired to spend or not)

  WAP54G (no cable) in Repeater mode for extending the range.

  All the foregoing are valid connections.

  Note: while the WAP54G is indicated only talk to the another WAP54G or a WRT54G in Repeater/bridge modes the WRT54GL is of the same family and should work, or if our local agent of Cisco says. We have not tested this.

  Concerning

  Fred

• IPod Classic 7 G 160 GB ' there was a problem installing this hardware: Apple iPod USB Device ".

  I have recently (June 2014) bought a brand new Ipod Classic 7 G 160 GB Model A1238.

  Whenever I connect via USB to a PC running XP SP3 and Itunes V10.0.7.2 it is always treated as if it were a new connection, i.e. "new hardware found". After trying to install it, it says so "cannot install this hardware" and "there was a problem installing this hardware: Apple iPod USB Device."
  I have also a 2009 16 GB Ipod Nano 4 G model 1285 and this is recognized by the PC whenever it is connected through the USB port itself.
  I connected the Ipod Classic 7 G to a laptop running Vista and Itunes V10.0.7.2 where the Ipod is recognized and installed.

  Even if the PC States that there is a problem installing the Ipod, it still appears in Itunes and I can download music to it and disconnect by using safe mode disconnect.

  PC XP SP3 - Ipod Classic
  I watched "Device Manager" under "Drives", the Ipod Classic is listed as an "Apple Ipod USB Device", but has an exclanation score against it.

  Right-click on the 'Apple Ipod USB Device' properties and the "Volumes" tab it shows the drive with the exact name and the size of the data, by clicking on the properties of "Driver" tab it says 'Unknown' driver provider, driver Date and Driver Version as being "not available". By clicking on the "Driver Details" properties, it shows a driver file-

  C:\WINDOWS\system32\drivers\PartMgr.sys, File Version 5.1.2600.5512 (xpsp080413-2108).

  Under "Device Manager" USB controllers, there is an entry for "Apple Mobile Devices USB Driver" and a "USb Mass Storage Device"

  The 'Apple Mobile Devices USB Driver' lists two drivers:
  C:\WINDOWS\System32\Drivers\usbaapl.sys and
  C:\WINDOWS\System32\usbaaplrc.sys

  The "USB Mass Storage Device" list a driver:
  C:\WINDOWS\System32\Drivers\USBSTOR. SYS

  PC XP SP3 - Ipod Nano

  I repeated the steps above with the Ipod Nano, connected to the PC and the driver provider is presented as Microsoft with the driver as 07/01/01 Date and Version of the driver as 5.1.2535.0.
  In the "Driver Details" properties, it shows TWO driver files:

  C:\WINDOWS\system32\DRIVERS\disk.sys AND meanings
  C:\WINDOWS\system32\drivers\PartMgr.sys.
  At the same time with the Version of the file 5.1.2600.5512 (xpsp080413-2108).

  The 'Apple Mobile Devices USB Driver' and "USB Mass Storage Device" are the same as for the Ipod Classic.

  I followed the procedure to remove Itunes and even the update to Itunes to V11.2.2 nothing works.

  I am aware that the system is also that XP can now be updated.

  So, why not not Windows Installer Ipod Classic and why the disk.sys driver does not appear

  According to the details of the pilot?

  Is the 7 G Ipod Classic not compatible with XP SP3?

  Yes it is compatible with XP SP3.

  Try asking in the forums of Apple iPod:

  https://discussions.Apple.com/community/iPod/ipod_classic?CategoryID=204

• Problem installing device a1530n

  Running Win XP Media Center Edition.  Had minor graphical problems at the top of the IE bar periodically endangered.  Decided to remove the Intel (r) 82945G Express Chipset adapter in Device Manager and then do a scan for new hardware.  And now I get the message of the new hardware detected that says.

  Cannot install this hardware

  There was a problem installing this hardware:

  Intel (r) 82945G Express Chipset Family

  An error occurred during the installation of the device

  Access is denied.

  I am connected to the computer as an administrator.  I tried to install this even in safe mode and get the same error above.  Any clues on what do I do?  The computer runs only in VGA mode.

  Thanks in advance.

  Link to screen shot of the error message.

• I installed Firefox4 already, however, when I try to install extensions, he repeats to me that I use Firefox 3.6.15.

  I installed Firefox4 already, however, when I try to install extensions, he repeats to me that I use Firefox 3.6.15.

  After that you have this problem, I also tried to reinstall Firefox, but nothing helped.

  Anyone has the same problem?

  https://support.Mozilla.com/en-us/KB/websites+or+add-ons+incorrectly+report+incompatible+browser

• Satellite P300-133 - problem installing Win Xp

  Hello

  I have a problem installing win xp to Satellite p300-133.
  To resolve this problem, I have tried the solutions:
  switch to ahci mode in bios and incorporating storage drivers compatibility intel to the installation cd xp with nlite, but none of them solved the problem.

  Laptop computer starts from the cd of xp and xp installation says "program Setup inspects your hardware configuration" and then a blank black screen comes.
  After that, the installation does nothing and waits indefinitely.

  Any ideas on this problem? Thank you.

  Hello

  > switch to compatibility ahci mode in the bios and the integration of the storage drivers Intel to xp with nlite installation cd, but none of them solved the problem.

  The two methods are good!
  You can install the Win XP without drivers Intel Storage Manager (SATA drivers) but in this case the SATA mode must be on compatible mode.
  It works for sure!

  The second method is the installation of the SATA drivers with nLite (drivers can be integrated into the new drive Win XP).

  I put t understand why this doesn t work on your laptop. I think it's a problem with your Win XP drive. Contains this Win XP SP2 or SP3?
  If this isn't the case, then you should use nLite to include min the Win XP SP2.

  Check it!

• Problems installing ZTE made map of internet data MTS on Vista

  Hi all

  I had problems installing a basic manufactured ZTE map of MTS internet data on my 32 bit Edition operating system, Windows Vista family. It's a HP Pavilion Desktop PC.
  When I install the data card a pop-up box comes up saying SETUP.exe. Then I run the installation file and it begins to install. Only towards the end it shows installation modem, then a pop with a Cape "Driver Installation" box comes up saying - "FAIL TO INSTALL MODEM. () - 536870389). »
  I spoke with the Multilateral Trading System (sellers of internet data cards), and they said to try the card of internet data on another system. I did and it works on my laptop and my office who has Windows XP. Then, it was clear that there is no problem on the side of MTS. The problem was with my HP Pavilion Desktop that is running on a 32-bit operating system, Windows Vista Home Basic.
  I then called HP customer support and they said to remove any program extra antivirus that I may have. I did but still no help. Again I called HP customer support and they said to take back all my files and perform a system recovery. I do that and then downloaded relevant drivers of drivers.blogspot.com and installed on my computer. After doing all this again I got the same error.
  Customer support HP said that there is no problem with the equipment and that I would need to Microsoft when there may be a problem with the WIndows Vista software. I called Microsoft customer service and they said to type the details of this error on answers.microsoft.com so here I am.
  Can someone help me solve this problem?
  I'd be willing to provide any other necessary information.
  Thank you.
  Concerning
  Jackie.V.H.
  Bangalore
  India

  Hi Jackie.hin,

  Method 1
  I suggest you to install the data card drivers in the clean boot state.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: follow step 7 of section of boot KB929135 to the computer in normal mode.

  Method 2
  If the steps above fail, then I suggest uninstall you the data card completely drivers by running the fixit and then re - install.

  Diagnose and solve the program installation and uninstallation problems automatically
  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

  Additional information:
  How to troubleshoot issues that may occur when you install, uninstall, or upgrade one program on a Windows computer
  http://support.Microsoft.com/kb/2438651#reso3

• WRE54G canmot associated not with this access point in Repeater mode.

  Hello

  Because of the concrete walls, I have a weak signal to use the WRE54G to extend my existing wireless network. However, I installed an Ethernet cable and found possible to connect the WRE54G access point. This is my extension of network is via a connection to an Ethernet cable. Is seems to work fine, it allows communications to the internet and shows a power good signal from a remote PC. But it works only in unsafe mode.

  Although I tried to reset, and then follow the instructions to set up a new WEP or WPA encryption, the installation program recognizes the WRE54G, but does not allow me to save the configuration.

  The error it says it is "WRE54G canmot not associate with this access point in Repeater mode.

  Help, please

  Make sure your router's wireless settings and WRE are the same. Try changing the channel on your router, if your router's wireless channel is the default after the procedure, your WRE is unable to communicate with your wireless router.

• Problem installing driver Lexmark x 8300

  I am running windows 7 64 bit system. I have a Lexmark x 8350 all in one printer inkjet attached to my PC everything was fine until when I got an error message saying that the pc and the printer did not communicate a few weeks ago. After having checked the connections, I tried to reinstall the printer and we was told that installation was not possible and got an error message 0 x 00000006.

  Since then, I uninstalled all the software of printer and tried to reinstall. When I do that, I tells me that the printer driver and when Windows searches for a driver, it is impossible to find one that works.

  I went to the site of Lexmark and they inform me that the driver for Windows 7 64-bit is the same as that for windows Vista 64-bit.

  When I try to install this driver installation fails because the Lexmark driver does not install. If I have trouble shoot that Windows searches for a driver, the system tells me the process has failed.

  I tried a such own restart as suggested by the community, but not luck.

  Is it possible that an update of installed Windows 7 recently caused an inconsistency with the Vista driver for the Lexmark 8350?

  Thanks for any help

  Follow the steps below.  If they do not work, please provide the full text of the error message that occurs when you try to install the driver.  See also the following, which strangely resembles your situation, but the fact that you did not mention that your printer is connected on a network--> https://patrickhoban.wordpress.com/2013/10/30/0800-9/

  1. disconnect the printer from the computer (I assume that the printer is connected directly to the computer via a USB cable).

  2. go here--> https://support.microsoft.com/en-us/kb/2793718 and download both of the correction he routines.  In other words, if you are using Internet Explorer, choose 'Save' instead of 'run '.

  3. download a new copy of the driver Vista 64 bit (cjs8300EN.exe).  Temporarily disable your antivirus software before you click on the Download"" button.

  4. After you download the driver file and the two Fix it routines, disconnect your computer from the Internet, then you can let the disabled antivirus.

  5. uninstall all Lexmark software using the control panel > programs and features.

  6. you will probably need to run mode 'Full' set of routine, but be aware that this will delete ALL printers currently installed.  Full Fix mode it basically puts your print environment to the way it was during the installation of the operating system.  You must restart the computer after you run the Full Fixez_ mode the.

  If this Lexmark is your only printer, and then use Full mode repair.  If you have other printers, you can see if the "light Mode" Fi xit has solved the problem, but I suspect it won't.

  7. After executing according to the difficulty of what you have selected and reboot if you have selected the full mode, run the driver installation program.  Connect the printer to the computer when you are prompted during the installation of the driver, or when the installation is complete.

  If you use the light mode set and the driver installation has not been successful, start back at step 5 and secure it using the full mode.

• problem installing windows 7 finishing installation scope and freeze for hours please help

  problem installing windows 7 finishing installation scope and freeze for hours please help

  my pc req:
  2 GB of ram
  NVIDIA geforce 210 1 GB
  180 GB
  Pentium 4 3.40
  Help, please

  Turn off the computer.

  try to start safe mode, start your PC, just before the system loads the Windows operating system. Press the [F8] key function 8 on your keyboard which will launch the menu Advanced Boot Options. Select Safe Mode.

  Log, click Start, type Device Manager, press ENTER.

  Expand graphics cards

  Right-click your video card, click on uninstall.

  Restart your system

  Log, click Start, type Device Manager, press ENTER.

  Expand graphics cards
  Right-click your video card

  Driver update software; then click search automatically for updated driver.

• problem installing Realtek audio on Windows 8

  Realtek Hd audio is not install on my newly improved windows 8 pro. I officially used windows 7 ultimate on my hp pavilion dv 6000. I downloaded the windows version 8, but whn I tried to install it, it kept giving me an error message 0001. I also tried to install srs audio essential also, but this force is not working either. is there something im doing wrong...? ... Please, can you help...?

  Hello

  What is the accurate and complete error you get when you try to install audio Realtek?

  The problem could be due to the driver compatibility.

  As I see the drivers for audio Realtek is not available. I suggest you to download and install drivers in compatibility mode. http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=2093&LC=en&cc=us&DLC=en&sw_lang=&product=1842155

  Make the programs more compatible with this version of Windows
  http://Windows.Microsoft.com/en-in/Windows-8/older-programs-compatible-version-Windows

  I hope this helps. Let us know if you have other problems with Windows in the future.