Problem installing Windows Vista Service Pack 1
Greetings,
I've been running Windows Vista for a while now. In general, I have no problem. I tried to install Service Pack 1 with a bit of luck.
My first attempt was to install using Windows Update. When it installs it gives me error 0 x 80070490
My second attempt was to install it as a Sandalone by Windows.com. He also gave me an error
0 x 80070490
I followed the instructions at http://support.microsoft.com/kb/947366.
I tried all resolutions and nothing will work.
Both times when I try to install it, the bar fills up all the way and then fails (no reboot or anything else) with in a few minutes. It restarts what only it either just fails or not. I tried using safe mode and normal Mode.
I tried to repair Windows to solve the problem. While the repair done, the computer has restarted and gave me the 'blue screen of death', the only way he could properly load was to load mode without failure. I had to wrap the last know configuration to start normally.
I'm running out of good ideas please help
Desperate, try: http://support.microsoft.com/kb/947821
Description of the preparation tool update for Windows Vista for Windows Server 2008 and Windows 7 system
Usually, the tool is available to computers that could benefit from these tools, but you can manually download the same and see if it helps.
Unfortunately with your error code, it is usually a necessary repair install, but the damage may be too much even for a repair installation.
BTW - back up your important files just in case where you don't have to start over.
TaurArian [MVP] 2005-2010 - Update Services
Tags: Windows
Similar Questions
-
Problem installing Windows Vista Service Pack 1 (KB936330)
Service Pack 1 will not download, end as an error message. The error Code is 0 x 80070002. Can someone help me with this?
Hello
You also need Service Pack 2.
Click Start > right click on computer > left click on properties > see if you have Vista 32 bit or Vista 64-bit installed.
It will also tell you which SP you have installed.
Then, choose the download of 'bit' OK to use to install Service Packs, installation of SP1 first if it is not already installed.
Vista SP1 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=30
Vista SP1 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=21299
Vista SP2 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=16468
Vista SP2 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=17669
This Information Microsoft can help you resolve problems that you encounter during the installation of Service Packs for Vista.
http://support.Microsoft.com/kb/947366
___________________________________________________
«Error Windows Update '0 x 80070002' or «0 x 80070003 "»
http://support.Microsoft.com/kb/910336/en-us
See you soon.
-
I installed windows vista service pack 1 and now problems
I installed windows vista service pack 1, and now it will not connect to the printer and I have no sound! I've updated the drivers of the two, and they work both according to their status of device but no sounds or printer connection. Help, please.
Once solve you the problems with SP1, you can then start of SP2.
How to resolve problems that you experience after you install a Service Pack for Windows Vista
http://support.Microsoft.com/kb/948481A device driver is not installed or a hardware device does not work correctly after you install a Service Pack for Windows Vista
http://support.Microsoft.com/kb/948187Important: things to know before you download Windows Vista SP1
http://TechNet.Microsoft.com/en-us/windowsvista/bb968859.aspxLearn how to install Windows Vista Service Pack 1 (SP1)
http://windowshelp.Microsoft.com/Windows/en-us/help/133c8953-c9cd-4FA5-8883-03e91bb6f2021033.mspxand - how to uninstall Windows Vista service packs as a troubleshooting step
http://support.Microsoft.com/kb/948537Learn how to install Windows Vista Service Pack 2 (SP2)
http://windowshelp.Microsoft.com/Windows/en-GB/help/105f7420-6f7f-4FE8-8698-2f40ca5f53711033.mspxInformation about Service Pack 2 for Windows Vista and Windows Server 2008
http://support.Microsoft.com/kb/948465Windows Server 2008 Service Pack 2 and Windows Vista Service Pack 2-five language standalone (KB948465)
http://www.Microsoft.com/downloads/details.aspx?FamilyId=a4dd31d5-F907-4406-9012-a5c3199ea2b3&displaylang=enHow to get the latest Vista Service Pack
http://support.Microsoft.com/kb/935791 -
my laptop is messed up after installing Windows Vista Service Pack 2
My internet does not work and a message came up saying "internet explore has stopped working, there is a problem, windows will let you know if there is a solution" a box then came advising me to install Windows Vista Service Pack 2 and I did and now my laptop is messed up. After that I connected, a black screen appears then I found a solution in another forum and able to-> explorer.exe task manager and a something regedit and once my computer has restarted after it is a message saying "Windows has encountered a critical problem and will restart automatically in a minute." and internet does more either.
Help!Hi, somehow I managed to fix my laptop using other answers I found on the forums and they were based on what you sent me here. I now have another problem with my laptop on internet access and an error message appears on my firewall is OK, but my University has a firewall up, so I think I need to go see them on this subject. Thanks for your help, thank you very much
-
Windows Update installed Windows Vista Service Pack 1 KB (936330) three times
Although three times, Windows Vista Service Pack 1 has been installed, Windows Update still says it's an available update. Information system does not indicate that it has been.
What must I do to solve this problem?
Learn how to install Windows Vista Service Pack 1 (SP1)
http://windowshelp.Microsoft.com/Windows/en-us/help/133c8953-c9cd-4FA5-8883-03e91bb6f2021033.mspxLearn how to install Windows Vista Service Pack 2 (SP2)
http://windowshelp.Microsoft.com/Windows/en-GB/help/105f7420-6f7f-4FE8-8698-2f40ca5f53711033.mspxHow to troubleshoot Windows Vista and Windows Server 2008 service pack installation issues
http://support.Microsoft.com/kb/947366 -
ERROR_NOT_FOUND (0 X 80070490) when you install Windows Vista Service Pack 2
ERROR_NOT_FOUND (0 X 80070490)
I tried and tried again to install Windows Vista Service Pack 2 x 64-bit system, but this error message keeps popping up. I tried to search for possible solutions, but they all tell me I have to use my Vista DVD. But there is a problem, I don't have it. I mean, that is, the gateway factory pre-installed Vista on my laptop, so I don't have the DVD. Is there anyone who can help me? THNX.
Hi Jason,
You can try the following solutions.
Step 1: Download and install the system update readiness tool to run a single analysis for inconsistencies that may prevent successful installations of Windows Update.
Step 2: Try to install Windows Vista Service Pack 2 now and see if it helps.
Learn how to install Windows Vista Service Pack 2 (SP2)
See also:
-
Cannot install windows vista service pack 2
http://support.Microsoft.com/kb/958044
You receive an error code "0 x 80070490" when you use Microsoft Update or Windows Update Web sites to install updates
Windows Vista and Windows Server 2008 to solve this problem, you must perform a repair of Windows Vista or Windows Server 2008 installation. Run a repair installation will restore the current installation of Windows to the version of the installation DVD. It also requires the installation of all the updates that are not included on the installation DVD.
Note Run a repair installation will not damage files and applications that are currently installed on your computer.
To perform a repair of Windows Vista or Windows Server 2008 installation, follow these steps:
- Close all applications and restart the computer.
- Insert the Windows Vista DVD or Windows Server 2008 DVD into the DVD drive of the computer.
- In the settings window, click install now.
Note If Windows does not automatically detect the DVD, follow these steps:
- Click StartCollapse this includes this image
and then type Drive: \setup.exe in the box start the search .
Note The placeholder drive is the drive letter of the computer's DVD.
- In the list of programs , click Setup.exe.
- In the settings window, click install now.
- Click Start
- Click connect to get the latest updates for installation (recommended).
- Type the CD key if you are prompted to do so.
- Click Yes to accept the Microsoft software license agreement.
- On the which type of installation do you want? of the screen, click upgrade.
- When the installation is complete, restart your computer and try again to install updates.
If the above does not resolve the problem:
It comes with Vista, upgrade install and activate Forum.
You will get the best help for any problem of Update/Service Pack update Vista Forum; the link below:
http://social.answers.Microsoft.com/forums/en-us/vistawu/threads
When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.
In this way, you will receive the best help.
See you soon.
Mick Murphy - Microsoft partner
-
I get error 80070490 Windows updates when you try to install Windows Vista service pack 2.
error 8007090
I keep getting the error 80070490 update of the window when you try to install windows vista service pack 2. help Windows and support suggested that I insert the windows dvd the disk drive but I don't have a disk with my computer. I chose automatic convenience store on the microsoft support site. but I still have the same problem
Hello
Are you sure this is the error Code?
And not this one?
It is the opinion of Microsoft about the error code 80070490.
'You receive a "0 x 80070490" error code when you use Microsoft Update or Windows Update Web sites to install updates'
http://support.Microsoft.com/kb/958044
Method 1: run (Checksur.exe) system update readiness tool
- Download and run the system update readiness tool. This tool runs an ad hoc analysis of inconsistencies that might prevent future maintenance operations.
For more information on how to download and run the Checksur.exe tool, click on the number below to view the article in the Microsoft Knowledge Base: 947821
(http://support.microsoft.com/kb/947821/)Description of the preparation tool system update for Windows Vista for Windows Server 2008, for Windows 7 and for Windows Server 2008 R2
- Try to install updates again.
Method 2: perform a Windows repair installation
If method 1 does not resolve this problem, you can perform a repair installation of Windows Vista, Windows Server 2008, Windows 7 or Windows Server 2008 R2. Run a repair installation will restore the current installation of Windows to the version of the installation DVD. It also requires the installation of all the updates that are not included on the installation DVD.
If you do not have a DVD of Microsoft Vista, you will need to borrow a DVD of Vista Microsoft from a friend or work acquantance to do a repair upgrade Installation.
"This has occurred as soon as I updated from Windows XP"
You have the upgrade DVD?
Here is a tutorial on how to do it:
"How to perform a repair for Vista Installation"
http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html
See you soon.
- Download and run the system update readiness tool. This tool runs an ad hoc analysis of inconsistencies that might prevent future maintenance operations.
-
Try to install Windows vista Service pack 1 (K936330), need 25 character codes
Try to install Windows vista Service pack 1 (K936330), need 25 character code.
You don't need the code to install a Service Pack - what's your real problem?
Your system shows a non-genuine notice?
To analyze and solve problems for Activation and Validation, we need to see a full copy of the report produced by the MGADiag (download and save to the desktop - http://go.microsoft.com/fwlink/?linkid=52012 ) tool
Once saved, run the tool.
Click on the button continue, which will produce the report.
To copy the report in your response, click the button copy in the tool (ignore the error at this stage), and then paste (using r-click and paste or Ctrl + V) in your response.
-* in your own thread *, pleasePlease also state the Version and edition of Windows cited on your COA sticker (if you have one) on the case with your machine, but do NOT quote the key on the sticker!
http://www.Microsoft.com/howtotell/content.aspx?PG=COA -
Cannot install windows vista service pack 1, 57 gives error code
When you install windows vista service pack 1 that it says code 57 Windows update has encountered an error can someone help please?
Hello
(1) what is the exact\complete error message you get?(2) remember to make changes to the computer before the question?See the methods mentioned below and check if that helps.Method 1:Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
Back up the registryNote: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.Method 2:How to troubleshoot Windows Vista and Windows Server 2008 service pack installation issuesNote: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.Note: You should not turn off Windows Firewall unless you have another firewall is enabled. Turning off Windows Firewall may make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers.Method 3:The problem with Microsoft Windows Update is not workingHope this information helps. -
Hello
Three years ago, I bought a Dell Inspiron 1525 laptop. Never met a problem until I tried to install Windows Vista Service Pack 2. I already followed each step instructions Support of Microsoft issues Service Pack for any result or solution. In these cases, I have downloaded the pack update directly from the wepage of Windows Vista, installed Windows Update Readiness Tool, disabled my antivirus (McAfee) and came up with nothing. I even tried to install this update in Mode safe but also failed to install Service Pack 2.
What is happening all the time, is that I double click on archive downloaded in order to install (having already started my computer in Mode safe mode with networking reportoire and disabled the antivirus as well as its firewall). The Service Pack window opens and I click 'Next' for all the necessary instructions, including 'the computer automatically restarts. When the toolbar installation is completed, the computer automatically goes to restart itself. 3 steps appear as a requirement for the completion of the installation process. All goes well until he reaches "step 3 of 3:100% finished. Do not turn off your computer. After about ten minutes of stall in this step, the following message appears on the screen: "the Service Pack cannot be installed, returning from changes. Do not turn off your computer.
The computer then rolls back all the changes and initiated in the normal state. After the opening, the first window that appears displays the following message: "the specific driver is not valid. "(Details): error: ERROR_BAD_DRIVER (0x800707d1). I proceeded to check and update alone driver of my computer, then try again to install the Windows Vista SP2 and all the operation has been a failure. I was cracking my head trying to solve this particular problem, and each time the same error pops up. I am seriously considering reformatting Windows Vista from manufacturer CD from my Dell, but I don't know if that would help.
If someone could help or advise with everything that I would appreciate it a lot.
Kind regards
Rodrigo
Hello
Method 1: Follow the steps from the links below and check if the problem persists.Step 1: Safe Mode
I suggest to start the computer in safe mode, then try to remove the Briefcase icon and check if it helps.
Start your computer in safe mode
http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode
If the problem persists, I suggest you follow step 2 and check.Step 2: Clean Boot Mode
I suggest to maintain the computer in clean boot mode and check if the problem still persists. A clean boot to check if startup item or services to third-party application is causing this issue.
You can read the following article to configure the computer to boot:
http://support.Microsoft.com/kb/929135
Note: After the troubleshooting steps, please refer to clean the start link to configure the computer to normal startup mode.Method 2:Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updatesHope this information helps. -
Cannot install Windows vista service pack 2
OT: used to install service pack 2 for vista
: TRY TO INSTALL IT SAYS CANNOT INSTALL THEN RETURNS TO ORGINALL PARAMETERS CAN SOMEONE HELPHi Sime JX,
1. What is the accurate and complete error message you get?
2. you try to download and install Windows vista Service pack 2 or install through Windows updates?Method 1
I suggest you perform the clean boot and then install Windows 7 service pack 2.How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
http://support.Microsoft.com/kb/929135
Note: Follow step 7 clean boot KB929135 article to reset the computer in normal mode.Method 2
I suggest to turn off all antivirus and firewall on the computer and then try the steps from the following link:Disable the antivirus
http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
Note: Microsoft does not recommend that you disable the antivirus protection in most conditions. Disable the antivirus protection that temporarily to restore a computer.How to get the latest version of the Windows Update Agent to help manage updates on a computer
http://support.Microsoft.com/kb/949104Method 3
I suggest you make the SFC scan.How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
http://support.Microsoft.com/kb/929833 -
Cannot install windows vista service pack 1 and 2 error: 8007006E
Original title: Windows Service Pack 1 and 2 will be not updated
I tried a few times to download the Service packs 1 and 2 so that I can reinstall my Windows live messenger. I didn't have time to let it run full the last time, but this time, her gives me: "error (s) found: Code 8007006E - Windows has encountered an unknown error.
Usually I have no problem with my updates, they fit very well. This time, of course when I need it, he decides to not work (Murphey's law).How to fix this or get to download correctly, so I can reuse my Messenger? I uninstalled my Messenger when it stopped working (would not allow me to connect to all) for about a month or two.Thank you!!!Hello
1. can you install other windows updates?
I suggest you to follow the steps below and check if it helps.
Method 1: Try to reset the Windows update components and check to see if the same problem happens: http://support.microsoft.com/kb/971058
Method 2:
Try to put your computer in a clean boot state, and then try to install Windows vista service pack 1 and 2 manually.
By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.
How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
http://support.Microsoft.com/kb/929135Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.
Method 3: Try to install Windows vista service pack 1 and 2 from the link below.
Service pack 1: http://windows.microsoft.com/en-US/windows-vista/Learn-how-to-install-Windows-Vista-Service-Pack-1-SP1
Service pack 2: http://windows.microsoft.com/en-US/windows-vista/Learn-how-to-install-Windows-Vista-Service-Pack-2-SP2
You can also consult the following link for more information:
Troubleshoot problems with installing updates.
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates
Hope this information is useful.
-
original title: could not resolve the problem of Windows Vista Service Pack 2 update!
Hey there,
I got Windows Vista Home Premium Service Pack 1 in my laptop when I bought it. Recently there was no updates of security (e.g., KB2481109) to install it into my system with a error: 80073712 and I had received a notification from windows to install Windows Vista Service Pack 2update. I tried to install it from windows update, but I got the error: 8024200d. I read the solution on this site and followed by download the stand-alone file and install "System Update Readiness Tool" (KB947821). ". After that I downloaded the standalone version "Windows Vista Service Pack 2" (KB948465) and tried to install it, but I got the error: 800f081f. "» I did Scan SFC which there is "no question of integrity" in the system, uninstalled "Avira Antivirus software" and again tried to install Service Pack 2 , but again, I've got the error: 80073712 After all this I couldn't solve the problem. Please provide some tips if anyone has solved the same or has a solution!
Thank you very much
UD
Hi Electrocuteud,
You have access to a Windows Vista installation disc? If so, follow the steps in this document to perform an InPlace upgrade. This will reinstall Vista without making any changes to the files and programs on the computer. Even if your data and programs must be safe, it is always advisable to make sure that you have a recent backup before major changes on the computer.
-
I can't install windows vista service pack 2, receive the error code 490
Tried to install Windows Vista service pack 2. (KB948465). Received: Installation failed. Also: element not found. Error: ERROR_NOT_FOUND (0 x 80070490). and finally the code 490 - Windows Update encountered an unknown error.
Hello
You receive an error code "0 x 80070490" when you use Microsoft Update or Windows Update Web sites to install updates
http://support.Microsoft.com/kb/958044
This article explains how to troubleshoot problems when you install a service pack for Windows Vista or Windows Server 2008.
http://support.Microsoft.com/kb/947366
Use this forum link for all questions related to Windows Vista SP1, Windows Vista SP2 and Windows Server 2008 SP2 below.
http://social.technet.Microsoft.com/forums/en/itprovistasp/threads
Maybe you are looking for
-
Desktop HP ENVY Phoenix 810qe: desktop HP ENVY Phoenix 810qe
I wanted to know ifDesktop HP ENVY Phoenix 810qeComes with graphical bultin or only the dedicated graphics card?Please guide me so that I can make decision of purhcasing this product. Thank you
-
The Satellite screen a series becomes black
I just bought my laptop and twice in the last two days, I was in the middle of something and then all of a sudden the screen is empty. The computer continues to operate, but the monitor just goes black. It could be overheating or is this something mo
-
envy dv7: need to change the boot sequence in the BIOS
I'm trying to get to the boot sequence settings in the BIOS and I forgot the administrator password. Trying unsuccessfully to Afgter 3, I get the message according to 50902428. Can you help me get?
-
How to disable the Compatibility Mode for iTunes
Title: programs original compatibility Application Applications App Apps game games Legacy Crash crashes Hang hangs How can I turm to i-tunes program compatibility mode?
-
Windows live messenger... having problems with by-side config
original title: windows live messenger problems with side-by-side config nobody knows nothing about it pls