Problem intermittent boot Tecra S2 after pressing the power button

Similar Questions

• Satellite A200 23W stop seconds after pressing the power button / stop

  Hello all :)

  I just bought a laptop Toshiba Satellite A200 23W a few hours ago.
  I turn it on and let it complete the installation of Vista.

  After the installation of Vista finishing it asket to resturn laptop and from that moment, the laptop is "dead".
  After pressing on restart the computer (from Vista) computer turns off without problem, but he never did it again!
  After a few minutes of waiting, I tried to start it by pressing the power button.

  Now when I press the power button, I can hear the HDD work and most of the time until I see something on the screen of the laptop computer stops!
  Now, I noticed that both the battery indicator AND the DC IN light are hot flushing and stop Flash at times.
  Reading the manual, I guess that the DC IN indicator should Flash in all not well.

  I tried to uninstall the battery and try to start the laptop, but in this case I can't even listen to the HDD, commissioning!
  I try to unplag and replag (on the laptop as well as Jack) power cable but again no result.

  Any ideas of what past?
  Thank you very much

  I don't know what the problem is here and, in my view, should not be so important to you. Contact your dealer as soon as possible and to talk with him. Explain the situation. You will get may be new notebook. Otherwise, please contact the nearest authorized maintainer and let check your laptop.

  The laptop is brand new and it should work. Please do not wait too long.

• Tecra 5200 - nothing happens after pressing the power button

  When I press the 'power' of my Tecra 5200 kids button nothing happens, only the front panel power led lights, but laptop does not start - in fact, nothing happens.

  Earlier, I lived as a result of problems;
  -the internal HARD drive didn't work, so I put the HARD drive in the Select Bay adapter and switched 2 hard drives (for each child 1 HDD with their own software / games)
  -computer had very hot on the surface (I had tried to open the computer and to clean inside, but it is still very warm)

  Now to my question.
  -If the computer does not start, is because of the HARD internal disk problem (found out once in awhile, he recognizes an old HDD, I had attached to internal port, otherwise the DVD player was not working)- and an easy repair is possible
  - or would it be possible that the CPU got too hot and bust, which means that I spend any money on the repair.

  I hope someone can help and give his opinion.

  > Toshiba guy;
  > Please publish guides on your website on how to open the 'old' notebooks, in fact no one would spend money to repair them.
  I agree with you. I don't think that someone will spend a lot of money to pay reparations for these old books.

• my laptop stops automatically and randomly and start again after pressing the power button / stop

  Hello

  my laptop stops automatically and randomly and restarts after pressing power button.my pc running windows 8 version of system.can you please solve this problem.

  Hello

  Check if the quick start option is enabled, your laptop. Here are the steps:

  1. open the Power Options window. Use one of the following methods:

  A. press the WIN + R keys at the same time to launch the Run dialog box. After that, type powercfg.cpl , and then press enter.

  B. press the WIN + X keys at the same time to launch WIN + X Menu. After that, select Power Options.

  C. the Start screen and the Windows of type power will show the results, select the Power Options.

  2. click on settings , then choose change how the power buttons.

  3. scroll down and look for turn the (recommended) quick start under stop settings.

  4 uncheck the checkbox, and then click save changes.

  Note: if the option has said isn't here, scroll down and select change settings that are currently unavailable to change.

  5 restart your laptop.

  Let us know how it goes.

• My laptop remains blank after pressing the power button

  Hello.. Please I really need help on how to repair my laptop. a lenovo ideapad s40. The problem started out as occasional BSOD. Then he started turning it back on while it is used frequently and finally it crashed. I restored system jointly, but that did not fix it. I resorted to the refreshing it still was not the answer. Then I reset the system losing all my data but the problem persists. When the power button is depressed now, the screen remains blank, but you could still hear the rotation of the fan system. Please I really need help with this issue.  As I said, it's a Lenovo ideapad s400. operating system Windows 8, 4 GB Ram, 500 GB of hard drive capacity, Radeon graphics card. https://onedrive.live.com/redir?resid=BF0101CC285F8D47! 106 & authkey =! ACoA6t1Ih_cqx3s & ithint = the file % 2czip a link to the dump files.

  The debugging session: Mon 20 Oct 08:53:10.352 2014 (UTC - 05:00)

  Error checking 117, {fffffa80085e0010, fffff8800401f28c, 0, 0}

  WARNING: Unable to verify timestamp for atikmpag.sys
  ERROR: Module load completed but symbols can be loaded for atikmpag.sys
  Probably caused by: atikmpag.sys ( atikmpag + c 928)

  Follow-up: MachineOwner
  ---------

  Loaded symbol image file: atikmpag.sys
  Image path: atikmpag.sys
  Image name: atikmpag.sys
  Timestamp: Thu Aug 14 21:10:45 2012 (502AF715)
  CheckSum: 00061A 50

  This accident was caused by your ATI/AMD display driver.

  Update the driver from here: http://support.lenovo.com/us/en/products/laptops-and-netbooks/ideapad-s-series-netbooks/ideapad-s400-notebook/downloads/DS031962

• Pavilion 15, G8D9OPA #ACJ: my laptop does not turn on after pressing the power button

  HII, after a week that I have on my computer hp laptop 11 months but its not get. I even removed the battery and tried to get by pluging the adapter, but it doesn't work. What I would do. Please help me.

  Hi @Swati_20,

  Welcome to the HP Forums!

  It's a great place to find answers and advice!

  You have the best experience in the HP forum, I would like to draw your attention to the HP Guide's Forums:

  Learn how to post and much more.

  I understand that your Pavilion laptop not turn on.

  When I did a search with the product number, you provided I have no results.  Would you be kind enough to verify this information.

  How can I find my model number or product number?

  What operating system do you use?

  When you connect it to the power light on the power supply?

  Here is a link to the HP laptops - tests and using the AC adapter that can help.

  You can also try a hard reset.   HP - notebook computers use the hard reset to solve software and hardware problems

  Please keep me updated.

  Good luck!

  Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem as yourself. Please consider tagging the post in order to resolve your problem as " ""Accept as Solution"" " to help other members of the community!

  To show the appreciation for my efforts, please click the 'Thumbs UP' icon' below.

• Satellite A60 Shuts Down immediately after pressing the Start button / stop

  My A60 stops after 2-3 seconds when I press the power button to open the laptop. After pressing the power button, all the lights on, but until something appears on the screen, the computer cuts the power. Pleasure, DVD and disk hard audio work. At least, the sounds come from these materials. Also from the buttom of laptop, I see that the fan is running.

  This problem started anywhere Yesderday, I closed my laptop properly and carry my laptop to my friends. When I tried to open my laptop, this problem occurred and I could not open yet.

  I tried all combinations of use power supply and battery for power. Non of them works.
  Is there a had the same problem or have any diagonistics for this problem.
  Thank you

  Emrah

  Hello

  Try to connect the laptop to the external monitor to check if pictures or anything else appears on the second monitor?
  You can also try to use the FN + F5 combination to check if the display will change back to the internal display.

  But look, man, if you are not successful then I guess there must be a serious hardware problem and only the laptop technician might know what's wrong.

• Satellite L550-1CW does not start by pressing the power button / stop

  I have a Toshiba Satellite L550-1cw that won't start, lights up when I press the power button all the lights at the front, the fan starts and he is looking for a HARD drive for about 2 seconds and then stops.

  I tried a new HARD drive, but the same happens.
  I was told that all this must be ignored and buy a new one that is not an option.
  I love this laptop and want to run again as this is the best I have ever owned.

  Help, please

  Andrew

  Can you give us more information on this vulnerability?
  You see something on the screen after pressing the power button?
  You can access the BIOS by pressing the F2 key immediately after switching on the device?

  Despite this whole issue, I think that if nothing is visible on the screen it could be a serious problem with one of the following: RAM modules, motherboard, CPU/GPU.

  From my experience the RAM memory modules are not very expensive (2nd hand might be good enough) and the replacement isn t very delicate in the case where the faulty memory causes this problem, the laptop could be set for a little money.

  But in case of problems of motherboard, laptop repair procedure could be very expensive.

• Computer to close after pressing the close button in windows

  I had a problem for my computer to shut down after pressing the close button in windows. Windows starts to make the closing process as its suppose there just like the computer is supposed to to close it restarts. Its like I pressed the button instead of the button closure. Please tell me how to solve this problem, so I do not have the power button to get off the computer.

  What has not worked? What happened when you tried?

  Another suggestion, take a look in the system logs and errors and warnings and post here Event Viewer Application copies. Do not post on that more than 48 hours ago.

  You can access event viewer by selecting Start, Control Panel, administrative tools, and Event Viewer. When searching for the meaning of the error, information about the event ID, Source and Description are important.

  A tip for posting copies of error reports! Run Event Viewer and double-click the error you want to copy. You will see a button resembling two pages. Click on the button and close Event Viewer. This places a copy of the report to your Clipboard. Paste it into the body of your message. Make sure that it is the first dough right out of the event viewer.

  Hope this helps, Gerry Cornell

• PC does not start when you press the power button, after that starts automatically as a ghost!

  I have HP Pavilion a6030in, my pc does not start when I press the power button / stop ther, but she starts automatically after some time after that, it works fine.

  Even once when I closed and leave it for a while and still the problem is not resolved.

  Help, please

  I solved the problem

• HP Slate 6, (problem: do not turn on the display, by pressing the power button once)

  A month ago, I bought the HP slate 6. The screen does not light by pressing the single time power button. But if I press the power button three times, then it lights. I also make sure that the switch has no problem. I think it's a software problem not hardware.

  Do not forget that I have improved my slate to kitkat. This problem alone caught up in not before Kitkat.

  Best wishes for you

  Topic: Alxhan cc

  Thanks for the info!

  Usually, if a factory restore temporarily solves the problem, but it returns that it is because of the apps to steal resources.

  Try going through this guide that will give you some useful tips for monitoring resources and reduce delays in system:

  5 common causes of lag Android devices (and correct)

• Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

  It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

  I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

  If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

  Thanks for your help.

  Damicon999 wrote:

  Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

  no chime, black screen, that's all.

  I don't think they are infected.

  The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

  No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• I can't start with Satellite P10 by pressing the power button more

  I can't start my Satellite P10 by pressing the power button more.
  Sometimes, very rarely its starts when I hold the power button for a while say 10 seconds.

  I tested the power supply and a battery to my friends P10 (of the same type) and both work very well.

  So it must be a problem with the key.
  No idea what to do?

  Thanks for any help

  The best.

  Tobias

  If it s a button or a power supply electronic problem, then you can't do anything.
  In this case assistance by the technicians of laptop would be necessary.

  But the next time that you should try this option if the laptop turns on not;
  Remove the battery and unplug the AC adapter from the laptop for about 30 min.

  After this short period of time to reconnect the two parts and check if the laptop could start.

  Good luck

• Lenovo Y40: Must only press the power button two times to turn on

  Hello

  A few months ago, I bought my Lenovo Y40 on the Lenovo Web site and recently, to turn on, I have to press the power button twice. When I press that once, the Lenovo logo is displayed on the screen, but after 2 seconds it turns off. On the second attempt, finally the laptop turns on and the windows is started.

  In addition, rarely the phone stucks on the lenovo logo screen, is necessary to contain the power to reset.

  Someone had some problems like these describe above?

  Thank you.
  Pedro Lopes.

  Hello

  I contacted Lenovo's Support and they recommended to perform a full recovery of the system. Apparently, it worked because I did not suffer these problems since I got windows. Probably, there was a problem with the partition that has been responsible for the initialization of the system.

  Thank you, Pedro h. Lopes.

• Help - HP Pavilion a6030.uk desktop computer. Have to press the power button several times to start?

  Hello

  I have a HP desktop computer. The model is HP Pavilion a6030.uk, Opertating system: windows vista.

  My computer has had no problems at all until yesterday for some reason, I had to push the switch several times to start until he finally turned and did normal starts. As I would press the power as normal to start button, but all of a sudden, it turns off after about 2 seconds and so I would tap on the switch several times and each time it will not start and turn off, then the power button could be pressed again until it would finally turn on and start and run as normal and seems to work correctly. And it was the same thing today, I pressed the power button mutiple times (for example 6 times) until she finally started as usual.

  Savvy/computer im not very well informed or wise in this area, please someone will help me and give me some advice/help to fix/resolve this problem.

  Thank you for taking the time to read this and any help would be appreciated for this problem.

  Thank you.

  Vonbon90, welcome to the forum.

  When I see these symptoms on an old computer, I think it may be a power supply (PSU) failure/ing.  Here's a guide that will help your troubleshooting it.

  In addition, you could test the memory.  This can be done by removing all modules of memory and replacing them one at the time and start.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.