Problem starting Compaq 6720 s

I recently went into my bios Setup and click Load set default values and now my laptop does not charge upward, I get the blue screen of death flash and disappear.

I tried to reinstall my operating system, but it did not work as it says that my hard drive is not present and that I should check the set up.

The hard drive still works as I tested it outside and all work from the hard drive came.

Can anyone help?

@Winston1979,.

Run the Bios.

Reach:

Configuration menu of the native system-> device-> enable/disable SATA Mode configurations.

Changing the setting here on what you have now.

If you Select select disable and press F10 to save the Bios. Then go to file-> save changes and exit and press F10 for the economy again.

If you disable select Activate and press F10 to save the Bios. Then go to file-> save changes and exit and press F10 for the economy again.

Tags: Notebooks

Similar Questions

  • Compaq mini c110: problem starting Compaq mini c110

    Hello

    I have compaq mini c110 and when I start it up it gets to the windows loading screen and then it restarts every time. So I decided to reinstall windows. I tried with windows 7, I get the first screen where I choose language after that when I press on install it just "freezes". I waited 2 hours to get to the partitions so I can format them and install windows but nothing happened. Then I tried to install windows XP, I got to the part where he asks me what partition I want to install windows and when I select it it starts formatting and after 20 or 40% in fact, it gave me error that my hard drive is damaged and could not be partitioned.

    I want to know if I should buy a new hard drive in this case, I would like to buy ssd or is something wrong with my mbr, I would get another message if it's defective mbr and how could I solve this problem? Or maybe it's completely another thing?

    Thank you

    Hello @Kops1304,

    Welcome to the Forums of HP Support!

    I read your post on the hard drive and wanted to help you!

    Try to check the hard drive from the BIOS.  You can use the following documents to help you:

    HP Notebook PC - test a hard drive from BIOS

    HP laptops - Hard Drive failure errors: failure Imminent, Smart, BIOHD, HD535, etc.

    If the hard drive has failed indeed, then it must be replaced.  You can use this guide to help you replace the hard drive: PC Compaq Mini CQ10 Notebook and Compaq Mini 102 Notebook PC - Maintenance and Service of Guide (Chapter 4, Page 44-45).

    Please let me know if this information has been helpful by clicking the thumbs up below.

    Have a great day!

  • Compaq 6720 s won't start not

    Hello

    I have laptop Compaq 6720 s Intel 1.7 Ghz, 1 GB of ram, running Windows XP Professional.

    When I went on the laptopm the wifi led is on, power led is not lit and the led above the charge point lights with a light blue color and blinks. The screen is dark (see no activity here). I can hear the fans running and nothing else. It stays that way. When I unplug the power cord, the fans will continue to run and I had to cut the fans to perform on the power button of the laptop at all times.

    Even the laptop is turned off, the indicator light above the power cord blinks without interruption. I removed the battery and plugged the power cord. Always the same condition. Now, the laptop power cord is not connected. I have strength under tension of the laptop (which disappears in turn fans). But the led above the power cord keeps burning anything.

    I think I have a 1 year warranty left. I can communicate with HP service staff only on Monday. But I would like to know if I can do anything to throw upwards before that. More important, I want to know if my data is recoverable.

    Thank you

    Harish

    Try a hard reset.

    Remove the battery and disconnect the electric plug adapter.

    Press and hold the power button for 10 seconds. Then put the battery back and try a boot to the top in windows.

    If it does not try reinstalling your modules of memory and try a boot up into windows.

    Then see if external connection to the video out gives you monitor a way in windows.

    If it does not try to remove your hard drive and see if your laptop shows the BIOS screen.

    If still no go, pass any of this than troubleshooting insulation information about the HP Service Center.

    Kind regards

    ERICO

  • Network drivers for Compaq 6720 s

    Hi all.

    I tried similar topics before posting, finding nothing; so I apologize if I was wrong and a similar thread already exists.

    I formatted my Compaq 6720 s, re-installation of Windows Vista (the same system before formatting). After that, I noticed that miss me the network drivers (the computer is not able to identify wi - fi networks) and I couldn't find them on the net. I installed HP wireless assistant but it does not help.

    Also, I noticed that the system does not work in a full screen, but more about a square screen based on the height (so there is a black band on both sides), then, probably, I also have some problems within the video drivers.

    Thanks to those who will help me by telling me where to find the drivers.

    Concerning

    Hello:

    Here is the link to the support page and drivers for your laptop:

    http://h20000.www2.HP.com/bizsupport/TechSupport/home.jsp?lang=en&cc=us&TaskID=&prodSeriesId=3442832&prodTypeId=321957

    Paul

  • power on password HP COMPAQ 6720 s

    product - HP COMPAQ 6720 s

    Operating system - Windows 7

    error - power asking the password

    I run startup verification before this problem occure.

    I have laptop HP COMPAQ 6720 s. A few days ago, I run startup check using the bios. at the end of this review, I restarted my laptop. He sought power on password prior to loading the bios. I did not put any power on password until now. so please help me with this problem and suggest me a solution so that I can access my laptop.

    This means that someone who has used the laptop put a power on password in the BIOS. He did not by himself.

    Some computers laptops, generally older, may have removed BIOS passwords by removing the battery from the RTC for a few minutes. Yours is the older type and the manual, see page 36, shows how it is possible

  • SE error message: "Run"DLL"there is a problem starting. C:\Users/John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll

    Get the below error message every time I start my computer:

    Run DLLS
    There was a problem starting
    C:\users\John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll
    The specified module could not be found.

    Hello cuefox, thank you very much to judge me.
    We're here to help.
    Continue to browse the web with Firefox, thanks once more.

  • Printing in 2 programs problem started 2 days ago, only firefox works fine with Internet Explorer?

    Services Bank web site has a "Print - Friendly View" text, on the top right of the page that displays the account information in a different format if you click on the text. Printing all other functions work ok. The problem isn't when you use them Internet Explorer. The other program is on the Aflacs website, and the problem is very similar. When I click on the text stating "Print copy of invoice", nothing happens, as the text of the Bank. Both work perfectly with Internet Explorer. The problem started about 2 days ago. When it works well, a window will open and show you what it will print and you click on the text "print", and it prints. Any help on this problem will be greatly appreciated.
    Thank you
    Joe Anderson

    You have this problem when running in Firefox SafeMode?

    http://support.Mozilla.com/en-us/KB/safe+mode

    Do not choose anything at the moment, just use 'continue in safe mode.

    When in Safe Mode...

    • The State of plugins is not affected.
    • Custom preferences are not affected.
    • All extensions are disabled.
    • The default theme is used, without a character.
    • userChrome.css and userContent.css are ignored.
    • The layout of the default toolbar is used.
    • The JIT Javascript compiler is disabled.
    • Hardware acceleration is disabled.

    If this is not the case, see this:

    http://support.Mozilla.com/en-us/KB/troubleshooting+extensions+and+theme...

  • Satellite C670 problems start after upgrade of Windows 10

    Hi all

    I made an upgrade of Windows 10 but after that my notebank satellite C670 has problems starting. It is always after the Windows updates were installed. It displays the logo of Win, followed of a blue screen. After several ignitions and extinctions I can once again the password login screen. Have already reinstalled Windows 10 because I did not come to the login screen more. But the problems are still there with ignition and extinction attempts it works. But this isn't a solution. You have ideas - drivers for Win10 or bios? Thanks for help

    Hello, I have the problem of the grandmother after the installation of Windows 10 I have nothing white screen
    Impossible to do a spanking Granny restore F8 or F12 nothing to do
    If someone gives you the solution I'm interested
    Thank you, CDT


    Validation has been translated by Google Translator

  • My iPad has been slow and unstable. What can I do if this is caused by a virus from the Internet because that is what I suspect. The problem started after a message like "scripts to run.

    My iPad has been slow and unstable - it actually seems to be hung when I use it. Once I put it, a blue line with four faces (which forms a rectangle or square) appears on the display and moves as he tries to anticipate my next actions or touch on the scree. All started about four days ago while I was downloading of articles in google scholar. A message that reflects something as "run scripts" or "scripts to run" appeared just before the problem started. Please advise on what I can do.

    Try resetting your device. This will not erase your data stored on that device.

    • Press and hold the sleep/wake button
    • Press and hold the Home button
    • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

    Alternatively, you can go to settings - general - reset - Reset all settings

    If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

    Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

  • Qosmio F60 - hibernation of freezing and problems starting

    Hello...

    The problems started when my computer goes into hibernation mode and when I press the power button to launch once again, it remains frozen.
    I then press the switch to turn on it works again.
    Option just to start normally or in safe mode.
    Either way comp freezes in the middle of loading and I must push the switch down to the Tower model

    Then the new restart msg saying there is a problem in the start menu and asks me if I want to solve the problem
    I click Yes and a number of things have happened several times:
    (1) computer sets and loads normally
    (2) computer says he can not solve the problem and continues to load correctly
    (3) the computer freezes in the middle of loading or during the process of setting
    (4) computer sets and restarts but crashes in the middle of reloading

    I often have to go through this time half a dozen before I can load normally

    either way my norton antivirus has been come with messages saying I need to reactivate (my subscription is not exhausted) or an error has occurred
    have done a full virus scan - none found

    is this a virus problem? I do a system restore? any other advice?
    help much appreciated

    Hi kkle4,

    You use the preinstalled version of Windows 7 in Toshiba? I can t find any information in your posting on OS :(

    Otherwise I agree with Akuma and you should check the BIOS version and probably an update would be useful. Before you begin to update of the BIOS here are some useful tips:
    -Close all running programs (also, antivirus, firewall, etc.)
    -Make sure that you are logged on as an administrator
    -Unzip all files from zip archive
    -Connect the AC adapter before you can update the BIOS and make sure the battery is fully charged

  • Problem starting Equium L40

    Hello

    I use F1 to start my Equium L40 every time I tun turn it on. It will then start ok but he forgot the time and date, as soon as I update time / date, the computer works perfectly I can access all my email etc accounts without having to put anything.

    The problem started after the replacement of the battery because of that being almost completely dead. I noticed that the computer will not work on AC only without mounted battey but is still charging the battery ok. (if the adapter is ok)

    I love the computer and do not really want to buy a new, but it is very frustrating and tedious when I turn it on.

    Maybe there is a battery backup I can change to fix the problem?

    Any help would be appreciated?

    Hello

    Laptop should also work without battery but connected to the power adapter
    So I guess that your motherboard is affected in some way.

    If the RTC battery (bios) is empty, the time and date in the BIOS menu would be reset to the default value. But in my opinion, this shouldn't be a problem to use the laptop with AC adapter.

    However, the RTC battery can be charged to do that you need to connect the main battery and power adapter and the laptop must be turned on for a longer period of time (18-20 hours).

    Check it out!

  • HP27-k350xt:. On each startup, I get this message. "There was a problem starting C:\Users\bulldog2u\AppData.

    . On each startup, I get this message.

    "There was a problem starting C:\Users\bulldog2u\AppData\Local\callBuilder\xBin\CallBuilder.dll.

    Can someone tell me where to find this file?

    Thank you - BULLDOG2U

    BULLDOG2U wrote:

    . On each startup, I get this message.

    "There was a problem starting C:\Users\bulldog2u\AppData\Local\callBuilder\xBin\CallBuilder.dll.

    Can someone tell me where to find this file?

    Thank you - BULLDOG2U

    You don't want in this file.  Ads by Call Builder is malware that opens the ads on your computer.  If you encounter this error, then it is likely that you have an antivirus/antimalware program which was removed from your computer, but left the startup item.  More information on Call Builder, and how to remove can be found here.

    To remove this item from your startup list, follow these steps:

    System (Windows 7) Configuration utility

    1. In the start search box, type MSCONFIG and press ENTER.
    2. Click the Startup tab.
    3. Uncheck the items you want to run at startup.
    4. When you have finished your selections, click OK.
    5. In the box that appears, click on restart to restart your computer.

  • ATTENTION EXPERTS - Compaq 6720 s Reinstall xp without floppy disk

    How can I clean installed xp on a Compaq 6720 s without a disk so I can move to windows 8.

    I am running windows 8.1 the trial which expires

    Hello:

    Use this guide to find out how to integrate the Intel SATA drivers... read article from Intel and then read the downloadable document on how to integrate all the sata drivers.

    http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/SATA-drivers-for-XP-solution-on-0x0000007B-BSOD/m-p/114120#M17758

  • Re: Problem starting L300

    Hello. I'm having a problem starting my L300 - it works very well up until now and has suddenly developed this problem.

    When turned on it, - very slowly - boots for the logo toshiba with the message "F2 for the Setup utility, F12 for Boot Manager" standard, but does not spent there - if left for a while it's just back to the blank black screen, the cursor in the upper corner of flasher for turn a little and then out. F2 or F12 do anything.

    Anyone got any ideas, what could go wrong? :(

    Hello

    Sorry, if I do not understand you correctly. You have a message like, Manager of boot is damaged?

  • HP all-in-one 4620: uninstalled 4620 printer but getting 'problem starting HPStatusBl.dll' notice at startup.

    I uninstalled the printer software HP 4620 on my HP computer running Windows 8.1. When you start the computer, I get the message "error loading c:\programfiles\hp\hpofficejet4620series\bin\hpstatusbl.dll" window message

    Hey @SteveJG,

    I would like to help you today to solve the 'problem starting HPStatusBL.dll' message that you get on your computer Windows 8.1. I understand that the uninstall your HP Officejet 4620 e-all-in-one printer has not made a difference. Just so you know, this error message is for a 'service' that Windows is trying to start it's related to the HP device. I just go and delete this file manually. Please follow the steps below.

    1. Open the Start screen by selecting the Windows button in the bottom left of your computer screen, or by clicking the Windows button in the bottom left of the keyboard, to the right of the Ctrl key.
    2. When the splash screen opens, type computer (can show that This PC)
    3. Click on the computer (or PC) to start the window
    4. When the computer window opens, click on the Drive C
    5. Click on users
    6. Click on your user name
    7. Select AppData
    8. Select roaming
    9. Select Microsoft
    10. Select Windows
    11. Select the Start Menu
    12. Select programs
    13. Finally, click Start
    14. You will see a shortcut here to monitor alerts - ink HP xxxxx. Right click on this and 'Remove' it.

    Once the file monitor ink Alters has been removed, restart your computer to verify that the problem has been resolved.

    Please reply to this message with the result of your troubleshooting. Good luck!

Maybe you are looking for