Problem to start 10 PSE after it closed

Similar Questions

• Problems to start the iPad after the charge.

  I have left the iPad charging outside the area during the night and have had start-up problems. I have a screen black and white and on pressing them and holding the sleep/home button an image of a battery. I release the buttons and finally after pressing the buttons, I get my home screen indicating a 100% charge. Has happened twice in the last few days when I greeted the battery power to reduce to 5%. My question is - this problem occurs when the battery power is authorized to reduce equal to or less than 5% before recharging or is the battery dying and requiring a replacement?

  Without knowing at what age the iPad is, it would be difficult to blame it on the battery dying. I never let my battery get too low before I reload them iOS devices. In fact, I put my Air 2 iPad and iPhone 5s on the charger all night in order to get a full charge overnight. I use the iPad all day at work, so I need to reload or to take the charger and cable with me, I prefer not to do. I prefer to load the day after.

  Why don't experiment you a little and do not let the unit run as low. Maybe that load when it gets to 25% left and see if that makes a difference.

• ThinkPad 10: Someone else has problems with start-up after a stop?

  I noticed repeatedly that after I closed my tablet, and then click the power button again (briefly, for 3 seconds, 5 seconds for 10 seconds and required for even longer), the Tablet starts. If I come back 5-10 minutes later, and then press the power button, then it powers on the property.

  Everyone ran through this?

  OK, so it IS an error checking, which is simply not the same as before. The updated wireless NETWORK card drivers seem to have resolved this particular issue where 9f error checking as a result of one of the broadcom drivers. I crossed the dump and debugged it...

  In this case, it's always a 9f error checking, but it's the driver for power management native in Windows (acpi.sys) which was originally the error checking this time around.

  The fix was to install the Lenovo power management driver. After the verification of error no longer occurs, but Lenovo power management driver offers other errors of startup time. Without going into a long list, it causes delays in reconnection bluetooth keyboards after startup, as well as the player delays the NFC from start (which will be the litter to the event log).

• After the last updates of windows have problems with start up and now drivers

  Hello

  After the last updates of windows have problems with start up and now drivers. I get an error code 21 when I try to install the drivers AMD apparently missing.

  May 14, last night I had several (automatically) downloaded windows update

  Today, I was unable to boot my computer with Windows - tried the disk check, start checks etc, and eventually had to use System Restore (for help before the critical update to restore).

  Perfection, everything works, but knowing that windows will attempt to redo an automatic update, tried to check online - no one seemed to have a problem and (naivly) thinking I could always do another restore of the system, I rebooted again.

  Same thing worse. Could not do a sys restore either just before restarting or last night. Chose a date earlier (last week) but then lost the USB drivers and pilots display. Downloaded updated but refuses to let my AMD driver install Windows I have a very unpleasant screen... and I must now stop the installation of this update "critical."

  Would appreciate advice how do my installed display driver or whether anyone else has problems following this update

  Thank you

  Hi Jane,

  You have a disk to install Windows 7 with you?

  I suggest you to check the event viewer for error details report.

  Open event viewer.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

• After I open a document using Adobe reader DC and want to save it with the help of Save as when I try to open this operation all I get is an empty windo saying save as. This problem just started, note I'm on Windows 7 Prof

  After I open a document using Adobe reader DC and want to save it with the help of Save as when I try to open this operation all I get is an empty windo saying save as. This problem just started, note I'm on Windows 7 Prof

  Hi sgodwin2468,

  Make sure that Acrobat Reader DC is updated Release Notes | Adobe Acrobat, Reader.

  If the problem persists, try the solution below.

  The default "save under" Acrobat/Reader DC dialog box is different from the dialogue box you had in earlier versions of Acrobat/Reader, it also allows you to record in the clouds and previous locations that you saved the files. It is possible that when Acrobat/Reader tries to connect to the 'cloud', it runs into problems. You can try to disable this feature to see if this brings your backup in the back of the box: open Acrobat Preferences, then go to the "General" category and uncheck "show the online storage when you save files:

  

  Kind regards

  Nicos

• Cannot start CF 10 after upgrade Mountain Lion

  Hello

  ... was just curious to know if anyone cannot start ColdFusion 10 after update to OSX (10.8.2) Mountain Lion? Someone at - it not to be able to start it?

  Thanks in advance,

  Rich

  ... OK, with no. through Adobe or Apple (they have both pointed fingers toward each other, how to let your faithful between your contest pssing) here is what I did to solve this problem:

  I ran the installer in CF10 and the first thing that appears, it is that "..." CF needs a different version of Java to install this program, download it now? "I downloaded and installed the Java version and closed the CF10 Installer. Of course, CF10 began. I really hope this helps someone as this will leave many people swinging in the air...

  Rich

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• Since the update of 9.3.2 I have problems to start my iphone

  I updated my iPhone to ios 9.3.2 6s.

  Since then, I started having trouble when I start the phone.

  When the battery percentage shows something close to 37% or less, I always have trouble when I starts the iPhone after a stop down.

  I started with the iPhone, it starts normally and when the phone boot up completely, it stops immediately.

  I reboot but the battery symbol appears and I have to connect to the grid as it was completely empty.

  After this operation, the phone boots correctly and the battery shows the correct percentage and everything works fine.

  Trying to solve this I have reset the factory conditions and failed to restore the backup image, but nothing has changed. The problem remains.

  I must point out that everything began with the update to the latest ios version (9.3.2)

  If someone knows something about it, please advice.

  Thxs

  Try to download the free 'autonomy' of the App Store app. It will test your battery and let you know if you have a problem with it. Sometimes the hardware problems with an update, sometimes it's just a coincidence.

  Edit: Factory reset you did a full restore of the system like that? If you've done this from the phone itself, it did install a new copy of iOS.

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod settings - Apple Support

• ENVY of HP dv7 w / Win 8.1 freezes after the closing and re-opening of lid

  Computer: HP dv7 ENVY

  Processor: Intel Core i7-3820 QM 2.7 GHz

  OS: Windows 8.1

  Graphics Card & Driver: NVIDIA GeForce GT 650 M (worm 331.82)

  Since the passage of Win 8.0 to 8.1, my laptop does not respond to the new entry after the closing and reopening of the cover.  As an attempt to circumvent the problem, in Control Panel (Control Panel > hardware and sound > Power Options > System Settings) I selected 'doing nothing' for preferences "when I close the lid.  After having opened the lid, tab browser fail to loa, windows cannot be enabled/disabled and CTRL-ALT-DEL gives no answer (preventing access to even the Task Manager).  The computer must be restarted to continue in force.

  This solution seems to have worked, even if I do not know why the four actions that were "resolved" by the resolution of the problems of power would cause the issue.

  Thank you!

• I'm having a problem reinstalling Windows XP. After formatting the disk and create partitions, it will not complete the installation.

  Problem reinstalling Windows XP

  I'm having a problem reinstalling Windows XP.  After formatting the disk and create partitions, it will not complete the installation.  He goes back and reinstall Windows again.  I go through the installation of 39 minutes, the computer restarts to complete and it loops back and start the installation again. Why it does this and what I can do to move beyond this?

  Go into the BIOS and make sure that you your hard drive is not set to off, and that is the first priority boot CD and your second HD.

  Don't push when it restarts anything just to let him do what he does and report back if anything I'm sorry I have no idea.

• Starting slow/delayed after logging...

  I have a 9 year old, desktop pc Dell Dimension 4500, works under Windows XP.  Problem: When starting to shutdown or reboot pc, there is at least a delay time of 10-15 minutes until I can go online or open some programs.  By the Manager of Windows taskbar-> the 'Users' tab, I realize "User" is strangely empty - despite being connected.  After said time my "user" name appears, followed immediately by an access internet and other orders that have been requested.  I would be grateful for any suggestions how to get my "User" name to load / appear faster.  Thank you!

  Hi Nevets1901,

  User name that appears empty in the Manager of tasks could be related to performance on the computer problems.

  ·         Since when are you facing this problem?

  ·         There were no significant changes made on the computer before the show?

  Check to see if the following is useful.

  Method 1: Start the computer in safe mode and check the number. Report of the results.

  Method 2: Check to see if this article helps you.

  Increase the speed of the PC: optimize your computer, help your PC run faster

  See also:

  How to set performance options in Windows XP

• After I closed my XP pc I now only have a user account

  After I closed my pc I now only have one user. The other 4 have disappeared. A user who is available is my daughter and she is not a qualification. How can I get other accounts? I can't restore the old system because my daughter is not an administrator. Help, please

  * original title - lost account users *.

  Hi MyridianEdwards,

  1. did you of recent changes on the computer?

  2. do you have security software installed on the computer?

  I suggest that you try to start in safe mode and then try to log on to Windows by using the default Administrator account.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  If you are able to boot into Windows from safe mode then try System Restore to the point while it was working fine.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

• laptop won't restart after being closed briefly

  After being closed for a short period, when I opened my pavilion g6 - 1 b 60 I have a flashing light on the cover lock and my wireless light is orange and the scren stay black.

  Hi @hawkeye440 ,

  Thank you for visiting the Forums HP's Support and welcome. I read on your HP Pavilion g6-1b60us Notebook and get a white or black screen at startup. Try perform a reset.

  When you perform a hard reset note remove all USB devices. Disconnect all non-essential devices because they can cause problems.

  You can do a System Restore. System Restore will help if something is automatically updated and wasn't on the laptop.

  Hope this helps you.

  Thank you.

• Toshiba laptop start registry error after manual stop

  original title: Toshiba laptop start registry error after manual stop - HELP!

  Hello, I have a Toshiba laptop with Windows Vista.  Yesterday it froze completely upward and I had to manually close (hold the power button until stop you him) twice.  The second time when I tried to restart the came Toshiba screen, then the screen with the little scroll down bar, and then it went black, waited for a while, then flashes a bluescreen with a written up VERY quickly and cycles back to the Toshiba screen.  This time after the scroll bar it gives me white saying the writing system could not restart, and I want to start normally or startup repair. If I restart it through loading files, trying to fix it and said then he wasn't able to fix it and when I look at the details there something on a registry error.

  I really need to solve this problem quickly and desperately want to save all my files if possible because it's our main Mobile family that has all our digital photos on it and they are not saved. (I know, terrible of us).  Can someone help me?

  Thank you

  Charity

  Follow these steps to try to solve your problems of boot.

   

   

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• How can I reset my laptop to Nov.2010 - I have problems opening and send emails after January 2011

  I had problems opening and sending emails after January 2011 so I wanted to turn my back on Nov.2010

  Hello

  You cannot use the system back restore more than you have Restore Points. The only one
  Another option would be to return the system to its out of the box, as it was when
  you received. So, it would be better reset your e-mail settings and check with
  the support of your email provider.

  How to create a System Restore Point in Windows 7
  http://www.SevenForums.com/tutorials/697-system-restore-point-create.html

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  ============================================================

  These can help with system related issues:

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  =============================================================

  This is Hotmail:

  Windows Live Solution Center - HotMail - HotMail Forums Solutions
  http://windowslivehelp.com/

  Hotmail - Forums
  http://windowslivehelp.com/forums.aspx?ProductID=1

  Hotmail - Solutions
  http://windowslivehelp.com/solutions.aspx?ProductID=1

  How to contact Windows Live Hotmail Support
  http://email.about.com/od/hotmailtips/Qt/et_hotmail_supp.htm

  -------------------------

  And Windows Mail

  Windows Live Mail - Forums
  http://windowslivehelp.com/forums.aspx?ProductID=15

  Windows Live Solution Center - Solutions mail - Mail Forums
  http://windowslivehelp.com/

  Windows Live Mail - mail Solutions
  http://windowslivehelp.com/solutions.aspx?ProductID=15

  I hope this helps.