Problem UZ2715H monitor: current input synchronization is not supported...

Similar Questions

• currently connected adapter is not supported. system will continue on battery

  currently connected adapter is not supported. system will continue on battery

  BIOS is a newer A12. try to drain, but same problem. tried a different wall jack, same problem

  I don't have the battery connected more since its broken. I tried a different power adapter and its giving the same error. It only happens when I play games, meaning when it requires more power then my FPS fall and I can't play the game anymore. I think that its my motherboard. Help, please.

  Solved the problem. I swapped the video card in my m17x r4 (7970 m) friends

  No error message, no more FPS drop, reinstall the FANS.

• What does that mean? -This problem occurred because your graphics card does not support the required version of DirectX. This version of Windows requires a DirectX 9.0 compatible video card or newer.

  I tried viewing a presentation power point and got to page 2 and my computer crashed.  Thought on... what he did previously trying to display a PPP file, but I thought that it was not my computer to the actual file.  now I have my doubts and also this time an error message came that said... This problem occurred because your graphics card does not support the required version of DirectX. This version of Windows requires a DirectX 9.0 compatible video card or newer.  can someone tell me what I should do next?

  You left out which version of DirectX has been shown.

  As far as I know, your Intel 945GM should support DirectX 9 and because you have XP sp3, you must have at least DirectX 9 installed.

  I met the following, but it shouldn't apply to Powerpoint:

  Some such as the Intel 945 GM Intel video cards have a design limitation which may cause problems when you try to run the Source Engine games. 3D graphics kernel does not support transformation of material, light and the vertex shader to similar technologies, which is an important part of the pipeline of 3D acceleration. Instead, this functionality is emulated in software that can reduce the compatibility and performance with 3D games.

  I don't have a solution for you (assuming that DXDIAG, in fact, reports to have DirectX 9 or higher).  You can see if you install a new driver support, but if it were me, I would be first contact Acer technical support or ask your question in another forum as one of the following conditions:

  Intel graphics Forum: http://communities.intel.com/community/tech/graphics
  Forum PowerPoint: http://answers.microsoft.com/en-us/office/forum/powerpoint (select the corresponding forum for your version of Powerpoint).  Include the results of DxDiag, including the version of DirectX.  If there is something unusual about the image that causes the crash, include this info as well.

  Normally, for notebook/laptop computer, it is better to get the drivers of the mfr of computer rather than the manufacturer of the device.

  Acer drivers for your computer are here: http://support.acer.com/us/en/product/default.aspx?tab=1&modelId=535 (you want the Intel VGA for XP driver)

  Intel has a newer driver: http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Internet+Devices&ProductLine=Netbooks&ProductProduct=Mobile+Intel%C2%AE+945GM+Express+Chipset+Family
  It's the main Intel support page: http://www.intel.com/p/en_US/support/highlights/graphics/945gm

• How to disable the Message box 'the current compatibility setting is not supported. Turn off compatibility view before you run this web page.

  Hi all

  Since a few days, we are on 11.1.2.3.500 and using IE 11. In IE 11, we can use Oracle EPM Suite only in Enterprise Mode, otherwise only "Bindows" appears. Now, my question is how can I disable (or remove) the Popup Message "the current compatibility setting is not supported. Turn off compatibility view before you run this web page. "because it's really embarrassing that this message whenever I start a planning application, Manager of calc or what ever.

  Thanks a lot for your help.

  Kind regards

  André

  You can go to tools > compatibility view settings and you should be able to remove the Web site / uncheck compatibility view so that you won't get this message

  HTH

  Amarnath

  ORACLE | Essbase

• As the pipeline input channels are not supported.

  Guys, I have this script to add a vDisk to each virtual computer via one loop for each...

  $VMNames = get-Content "E:\Code\Scripts\VMware-VM-UpgradevHardware\VM_Batch-1.txt".

  # START the foreach loop

  {foreach ($vm to $VMnames)

  #Perform paraSCSI update

  Write-Host $VM

  Write-Host "Adding new CCG virtual disk..." »

  # Get - Vm $vm | New-harddisk - CapacityKB 2048 - persistent persistence

  $vm | New-harddisk - CapacityKB 2048 - persistent persistence

  Read-Host «allows to pause and check...» »

  . but when I run it, I get this error.

  New hard drive: cannot process the transformation of argument on the parameter "VM". As the pipeline input channels are not supported.

  E:\code\Scripts\VMware-VM-UpgradevHardware\pvSCSIUpdate3.ps1:55 char: 7

  + $vm | New-harddisk - CapacityKB 2048 - persistent persistence

  +       ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  + CategoryInfo: InvalidData: (EDM-SNEC - DBTEST:PSObject) [new-harddisk], ParameterBindingArgumentTransformationException

  + FullyQualifiedErrorId: ParameterArgumentTransformationError, VMware.VimAutomation.ViCore.Cmdlets.Commands.VirtualDevice.NewHardDisk

  Allows to pause and check...:

  Any suggestions?

  You should have an object VirtualMachine (output of Get - VM) on the hose, if you want to send it to the cmdlet New-hard drive.

  The concept of object by name (OBN) does not work for the channelling of entry here.

  You can do

  # START the foreach loop

  foreach ($vm in (Get-VM-name (Get-Content "E:\Code\Scripts\VMware-VM-UpgradevHardware\VM_Batch-1.txt"))) {}

  #Perform paraSCSI update

  Write-Host $VM. Name

  Write-Host "Adding new CCG virtual disk..." »

  New-disk-hard - VM $vm CapacityKB - 2048 - persistent persistence

  Read-Host «allows to pause and check...» »

  }

• Skype problem; Error "your current security settings do not allow this file to download.

  When I try to download Skype, I get "your current security settings do not allow this file to download.  Help, I need to be a speaker at a meeting using Skype.

  Where did you download Skype, it's here - http://www.skype.com ?  If not, download it here.

  Check your AntiVirus package or firewall to ensure that it does not obstruct Skype or the download site.

  What browser you download it with? If it is, try a test temporarily lower the security settings for the internet zone, and then see if you can download it. After the test, restore it to its original position. IE - tools - internet options - [security] tab - click on the globe (internet zone) and lower the slider. It downloads then? Don't forget to set the cursor when finished.

  Try to download it with another browser such as firefox or opera and see if that can download it.

• I just came to the new current version that does not support toolbar Google... lost all my favorites Googl and really piss me off the power! How can I switch back?

  To summarize, when I switched to this new version, I lost my Google toolbar that also included the different bookmarks for bookmarks in the toolbar at the top, or Firefox bookmarks. The two reflect each other and so I lost vital bookmarks that I had stored in the Google Bookmark program. I want to go back to the previous version.

  You are welcome.

  Please click the button solved it next to the answer that solved your problem of Firefox support, it appears when you are connected, so this thread is marked as resolved to help other users who may have this same problem.

• Message problem "version of NI-VISA, which is not supported on this operating system has been detected... »

  Good night!

  Recently, I want to install the driver NI-VISA on my PC because I needed for arduino. I checked the versions available for my operating system (Windows 8 not 8.1) I tried with 5.01, 5.2, 5.3, but in all cases send me the same message, I look in programs and features in the software section OR for uninstall (if I have) the older version of VISA, but I have found that I Don t have any version. Also I Don t have any version of the software NOR-488 or something like that on my PC (I Don t know if I have to install for installation of NI-VISA) and send me the same message again, I Don t know what to do, if uninstall labview 2010 or get a new version or uninstall 2010 and install NI-VISA and then install LV Please help me...

  Like I said I have Windows 8, I7 Proccesor, LabView 2010 installed with this product: Circuit design, lego mindstorms, engine performance, OR measurement and automation,-configuration system, TDM Excel and update service (all this United Nations programs and features in the software section of OR).

  Best regards and thanks!

  
  

• portable computer does not support. Yet battery monitor says "plugged in, not support.» What are some options?

  my laptop is connected, and yet power monitor says "plugged in, does not support." What are some solutions?

  Hi Joseph,.

  Something similar just happened to me. The first time they fixed it, they have replaced the adapter and the problem is solved. 5 months later it started to happen again and this time they replaced the battery, the motherboard and the milling table (thanks to heaven, it is still under warranty). Fortunately, thanks to the new adapters, battery started to load and the experience does not seem to damage it in any way (but you should keep your eyes on it anyway just in case).

  How they were able to say on my laptop - a Dell E1705 (other than just experience and common sense) was to go into the BIOS (starts, it should be a brief Flash on the screen telling you how to enter the BIOS setup or menu of the BIOS (usually F2) and check the battery information. He showed that the power adapter 'unidentified' instead "90W" list which should be when it is working properly and that the battery was not complete and not charging well plugged. They changed the motherboard and the roll the second time because it could also cause the adapter is not being recognized by the battery (or battery not not recognize the adapter).

  The beep is caused by power and its configured settings to warn you of a low and critical battery condition. In a normal situation, the computer will work right next to the power adapter and does not the battery (it is a way to help maintain the battery life is to run periodically and refill if we leave normally plugged in most of the time). If you remove the batttery entirely, the laptop will power? If this isn't the case, it is certainly at least the adapter or the motherboard. Eventually the battery will get if low, that he's going to sleep or hibernation, or the system stops (you should shut down normally before him to cold shutdown like that). If If, then I expect the tone to go further because it will detect is no longer a low battery charge, because there is no battery - but then you'll want to be sure to use either a battery backup UPS, or at least a surge protector otherwise already in place because if you lose the laptop battery will crash hard and this is not good for her.

  I'm using 32 bit Vista Business SP2 and in Control Panel / sounds / Sounds there is an option for low battery alert. The default to have this. In this case, you can turn off to avoid the beep. In addition, you can go into Control Panel / Power Options, click the plan settings and click on battery. It will provide you with levels of low battery and critical battery and you provide measures to be taken in such a case. If you are unable to operate the system without battery and it is so weak that the alerts began, you probably fell to 11-5% remaining. You can adjust actions to nothing for bass and stop to criticism that 5% is about as close as you want to get to the point where you can hang. Then, you just need to wait until it is repaired and the appropriate parts are replaced.

  Even if you have still some life in it, it is best to contact the manufacturer (they the some have the right parts) or a computer of reputable workshop to get a good diagnosis (perhaps by phone at first), a determination of what must be fixed, the applicable fees, schedule, if it is still under any kind of warranty , and what needs to be done in which order of repair. They can find the adapter is OK and it is just the battery (or vice-versa or two or more). But that's essentially where you need start.

  I hope this helps.

  Good luck!

• Graphics card does not support the required version of DirectX 9.0

  Problem message: this problem occurred because your graphics card does not support the required version of DirectX. This version of Windows requires a DirectX 9.0 compatible video card or newer.  My question is what that update of video card do I download to fix this problem and where can I find.

  Problem message: this problem occurred because your graphics card does not support the required version of DirectX. This version of Windows requires a DirectX 9.0 compatible video card or newer.  My question is what that update of video card do I download to fix this problem and where can I find.

  =========================================
  It may be interesting to try to go to support
  site Web of MFG. your video card and
  search for course Windows XP Compatible
  drivers.

  (FWIW... If your computer is a laptop... check
  the manufacturer of the comput4er one
  updated video driver)

  If you do not know the make and model of
  your video card... check documentation
  supplied with the computer.

  Also, you can try the following steps...
  Reach... Start / run... type...
  Msinfo32... Press on enter.

  On screen Information System... Choose...
  Components / display...

  You should find the make and model of your
  adapter display as well as the version of the driver.

  If the driver on the Web site is no longer
  current than you run...
  Download and install it. Also, you should find
  and follow the installation instructions on the
  support site. John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Display card/video card does not support DirectX

  First of all, I thank you in advance for any help I receive...

  When running a game program, on occasion, the program is interrupted by a blue screen with a message something very long fault and then my computer shuts down. When I reboot, I get the error message statement, I send and the message...

  To upgrade your

  This problem occurred because your graphics card does not support the required version of DirectX. This version of Windows requires a DirectX 9.0 compatible video card or newer

  If someone can point me in the right direction, until the card video and/or display adapter that I need, I would appreciate it. I don't run a daily automatic updates... don't know if it's important. Thank you, once again.

  Hello

  ·         What is the exact blue screen error that you are experiencing?

  ·         Game in which you try to read?

  ·         Which version of DirectX is installed on the system?

  Method 1:

  If you do not know the version of DirectX that is installed on the system, then, I suggest you follow the steps mentioned in the article below.

  How to determine the Version of DirectX using the DirectX Diagnostic tool

  http://support.Microsoft.com/kb/157730

  Method 2:

  I suggest to download DirectX on the system from the link below and then install it on the system and check if the problem is resolved.

  End-user Runtime Web install DirectX

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=2da43d38-DB71-4C1B-bc6a-9b6652cd92a3&displaylang=en

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.

• drivers NVIDIA for B560 (does not support IE9)

  I have lenovo B560 computer laptop windows 7 ultimate 32 bit with sp1

  downloaded the latest drivers Lenovo web site, but I have problems with final IE9 that it does not support hardware acceleration. We then see only blank white.

  can I put driver from nvidia website?

  Optimus works again after that?

  Maybe lenovo will release new drivers?

  you have treid to re - install it IE?

  You can download/install the drivers from nvidia. If everything goes wrong, restore your computer to the restore point previous.

• 'Input not supported' with Acer AL2216W monitor

  I use Windows Vista Home Premium with Service Pack 2 in a system with an Intel D946GZIS motherboard and an ACER AL2216W LCD display panel. This system has worked well for over a year, but recently in a battle of two months with a problem of code 10, the screen would occasionally drain and display "Input not supported" in a small floating window. As a first step, start with F8 would allow the system to boot in a 640 x 480 window which would quickly find its native resolution of 1680 x 1050. But now it starts directly from the screen to 640 x 480 to the State banned in normal mode, make possible adjustments to display.

  I can still use this display Mode without failure, but find that Safe Mode display adjustments do not affect the display in normal mode. In addition, a panel of HDTV used as a monitor instead of the Acer works wonderfully in normal mode in 1920 x 1080, but display settings to a lower resolution made with it do not persist when Acer Board is restored. Finally, my system is no longer recognizes the Acer AL2216W, but use a "default monitor.instead." And I can not install the Acer in the Mode panel without failure!

  You can try to uninstall your display driver in Device Manager, then reboot. Check if the monitor is listed under Device Manager. Your monitor should be below or try to reinstall the driver using the procedure on the link in my first answer.

  You can then go to the support site for your computer manufacturer and download the latest display driver specific to your operating system. Look for instructions on how to uninstall previous drivers and install the latest driver.

• Not supported input message appears on the monitor

  "Input not supported" message appears on the monitor whenever I try to watch a DVD or video stored on my hard drive

  What could be the cause of the problem? The monitor is an Acer x193w. I got this computer for over a year and I've never been able to watch a DVD in its entirety because after so long as the message arrives and the only way out of the said message is to manually cut the power goes to food. I tried the alternative media such as VLC players to see if it works, but it seems to be something else the cause. This happens only when I run the videos that have a considerable length (20 minutes or more)

  Hi CheerleaderMelissaFan,

  Through my research, I noticed that users with similar problem have solved this problem by changing the screen resolution, I suggest you to change the display resolution and make sure that the refresh rate is adapted to your monitor.

  Follow the steps mentioned in the link below

  Screen resolution-change

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-screen-resolution

   

  Change the refresh rate

  http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

  (You can see the documentation for the monitor to the native display resolution and refresh rate)

  Now test to see if the problem is resolved, after back if you have any questions

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  Apparently, you're trying to use AirPlay to display content that is protected in a way that not only allows the copy.