problem with a block of memory in labview 2009

Similar Questions

• Problems with tdms built executable; memory.cpp write error

  Hello

  I have a problem with writing tdms files in bed which executable, that I created with the Builder application in LabView 8.2.1.

  I created a small requesting readings some channels in the DAQmx. This schould results written in a PDM file. All this happens within a while loop, even the steps open-entry-closing-PDM.

  This test in the development environment everything is fine. But if I create an executable file and try this on the same and other computer, I received an error warning.

  The error that says: error on line 342, memory.cpp

  Is there anyone who has any idea what is the problem? What I have to insert something in the creation of PDM application designer?

  best looks, T.Malec

  The problem of TDMS is special to 8.20. However, you cannot run the executable with a new runtime, because the compiled code is not compatible between major releases (example: code compiled with 8.5.0 will run on 8.5.1, but not on 8.6.x).)

  Herbert

• Problems with e250 and SD memory card?

  Basic information about the player: e250, 2 gig, version 1, 01.02.24 has

  Basic information on the SD card: Sandisk micro SD, 2 GB

  I have my sansa for a year and a half, and I have never had any major problems with it so far.  Recently, I had to remove the songs to put on the new songs due to lack of memory, so I decided to buy a memory card for it.  Getting the empty memory card I inserted and recognized my drive and everything was fine.  The problems started when I put songs on the memory card.

  I put my player in MSC mode (as indicated in the manual), it is hooked to my computer (windows XP), and everything was fine.  I used windows media player to synchronize music on the memory card, then picked up my drive.  It is restarted, as he should, and I went to listen to music I would put right on and yet once again, it was fine.  Then, I wanted to listen to my music, and he flipped out on me and wouldn't let me play it.  After determining that it was not just this song, I removed the memory card and tried to play the old music, but he would always let me.  A small red box saying 'Wrong way' just kept popping up.

  I decided to start over, so I have deleted all of the player (via the computer) and then attempted to deliver music on.  I tried a few songs, sync and play the two media of windows and my computer says that the songs were on the player.  To get the player from the computer, I went to "songs" and saw that it was always empty.  I hung up, and the computer says that these songs are on the player.

  In a nutshell: my computer says it is synchronization of the songs to the player, but in reality, it isn't.  This has only started to happen after I had the memory card.

  If someone could help me, that would be great.  Thank you!

  I don't think that Windows Media Player will work in players v1 in MSC mode. It must be in MTP mode for WMP to recognize. In addition, with the cards in players v1, you HAVE to add/remove music in MSC mode only by drag and drop from your computer to the card (read as a drive in Windows Explorer). You have to treat the reader and the card as the "separate entities", even if physically they are connected. Once music is on the map, the player will fit perfectly on both songs.

  In what concerns the "bad tracks", you need to run CHKDSK to repair corrupt files, so you can remove them properly. Answer NO when it asks you if you want to save the files "bad strings" (or something like that). Check the 'sticky' & the FAQ at the top of the body for specific instructions on running CHKDSK. While you're at it, also check out & play on your player of formatting, as you should probably next to you to go to a clean slate.

  I believe that files (songs) put on using WMP in MTP mode can ONLY be played in this mode, and MSC placed files using drag ' drop can be read in THAT mode, which can be part of your problem. Probably best to start fresh and then don't forget you must manually put the songs on the map in MSC mode.

  Another oddity of SD cards (at least with players of v1) is that you must also manually add the 'album art' to the file containing the music if you want to see the album art that song. With WMP and MTP mode on the player, it will play the album art embedded in the ID3tag. It will not do this on the SD card . You can see specific instructions on how to do it here. There is also a video showing the procedure here.

  I hope this helps...

• Problems with PCI-7811R after upgrade from LabVIEW

  Hello

  I have been using a PCI-7811R under LabVIEW 8.2 for quite awhile without difficulties. However, I just upgraded to LabVIEW 2009 and it seems to have stopped working.

  I tried to run old code (that worked before) and I get the attached error. I try and locate the PCI-7811R in MAX ver 4.7.7 and he's not here.

  Any suggestions?

  Gary

  
  

• Problems with the Display Mode target on end 2009 27 "iMac

  Used late 2009 iMac 27 "in the view target in conjunction with a Dell XPS tower with i7 processor, Windows 7 and the best graphics card I could afford at the time connected by HDMI to mini display port cable.  Worked well for years.  Set aside Dell for a few months and the update of the iMac to El Capitan OS 10.11.3.  Recently tried old setup with same Dell PC and was able to move from Mac to PC, but the PC screen resolution was at the lowest setting. I got an error message when enabling/disabling to PC who said there was a problem with the port causing mini display of the system back to the lowest resolution. Impossible to reset at a higher resolution.

  I tested the Dell PC on another monitor, and it works very well at higher resolution (2560 X 1440). Now, when I reconnected it to the iMac (which works fine), the screen becomes black.

  Is it possible that the operating system upgraded (El Capitan) is not compatible with the targets using mini display port Display Mode?  Any ideas?

  Use your iMac as a display with the target - Apple Support Display Mode , also consider having a bad cable or connection. Does not hurt to try different cables, they can and will the bad!

• Problem with 16 GB Sandisk memory card

  Hi all

  I just bought a Clip Zip and use a Sandisk memory card to use with it. Unfortunately, while most of the library, there are a few artists who don't. I tried moving them on the player's memory, and then they operate, so it seems to be a problem reading the card, rather than the tags of the files. I bought the card from Amazon, so I eliminated the possibility that it might be a fake card. Does anyone have any suggestions as to what may be the problem?
  Thank you very much for your help!

  How many records you on the drive? Keep inmind that the zip has a database of song 8000 limit. anything above 8000 will not be crawled and appear not in the menu. If you have less than 8000 files can you put some of the bad files so we can take a look?

• Problem with variables stored in memory/cookies.

  I'm not really sure what's going on, but that's what happens.

  I have a swf file that connects to a server through a file, but that seems to hold some variables in memory or something to make it works fine the first time it is loaded, when I load the page again, either the browser or the drive is not compensation on the previous values. I don't know if there is a way to ensure that the swf file when it loads ensures don't not to keep the values in the cache.  In fact, it seems that the only way to get around my problem is to erase cookies from my site and then recharge.

  Any ideas?

  site: http://condechi.com/test/movieTest.html

  Thank you

  O

  generally speaking, adding a query with changing value string will prevent items being retrieved in the browser cache.

• a problem with an installation of memory

  Hello

  I have trouble to install memory in addition to my currnt one card.

  When I use the old one only it workes very well. When I use both my cmputer won't turn on. Instead, I hear 5 sound "beep". It lights when I use my new single memory as well.

  I want to know what I'm doing wrong and what I should look for in a memory if mine does not fit my computer.

  I use:

  Win7 starter

  computer pentium 4 32-bit.

  the memory I have installed on my computer is:

  DDR2
  512 MB
  PC-2 4300 (266 Mhz)

  the new memory I bought is:
  Kingston 512 MB DDR2 533 mhz pc2-4300 NON ECC Unbuffered Desktop PC RAM memory

  My motherboard model:
  HP-09f0h
  Since its an old computer, I have not found an answer to my problom.

  If you need more info, here is my cpu and motherboad info:

  motherboard Info

  CPU - info

  Thank you!

  Whenever you do an upgrade of RAM in the future and you want to it works as expected the first time it is turned on:

  Always purchase compatible memory modules guaranteed

  upgrade only pairs of identical memory modules.

  What you are experiencing, it's what I expected to happen because you do not follow these two rules "" upgrade memory in PCs and laptops. Mixing memory you made generally results in failure at startup or in an unstable operating system.

  I can't tell you what should work, because you have not identified your PC. This is not the same as upgrading a self built PC. Manufactured of PC memory upgrades are always executed by matching the name of the manufacturer of the model to the list on the site in the configuration utility or the manufacturer of memory by the manufacturer. Find a serial number on the side or rear. Post here the number of full product in the wire.

  If I want to add memory to my motherboard ASUS Crosshair V Formula-Z, I look in the manual of the motherboard memory compatibility list. It is quite different with a manufactured as your desktop PC.

• How to solve the problem with the blocking of my hotmail account?

  I can not connect to hotmail. He say, I've been blocked, wants me to put in info in order to restore, but nothing happens. It also allowed me to change my password, but can't always get to my ACCT. I give the e-mail address of my spouse for a response from you.

  You could start with the Windows Live Solution Center, take a look at:

  http://windowslivehelp.com/solution.aspx?SolutionID=f172cbee-3c73-4506-8a1d-4e6e82adb846

• Hi, I have a problem with my computer laptop memory

  I have HP Pavilion laptop g6 with windows 7 ultimate 32 bit, my laptop has only 4 GB of RAM chip, but when I check my windows system properties, installed memory is 4 GB but only 932 MB is usable!

  Kindly how can I fix this and increase the size of the windows usable memory?

  Thank you

  -Go back to msconfig and click on the Startup tab > Advanced Options and clear the check box
  next to 'maximum memory', if it has been checked.

  -If you don't the have not already, update the BIOS of your motherboard can also help. See the download page from HP for the updates to the BIOS (can check motherboard driver updates as well).

  If the fixes above do not help, you can find something in the article below.

  http://support.Microsoft.com/kb/978610

  Hope this helps-

• Problem with less available graphics memory.

  HI all, I have Mobile Intel(r) 945 Express Chipset Family on my laptop ACER ASPIRE 9410-4317, have the 160 GB HARD drive and 1 GB of RAM. the report on my graphics card is

  Intel(r) Graphics Media Accelerator Driver for Mobile report

  Date of report: 11/18/2009
  Report time [hr:mm:ss]: 18:11:59
  Driver version: 6.14.10.4926
  Operating system: Windows XP * Professional, Service Pack 3 (5.1.2600)
  Default language: English
  DirectX * Version: 9.0
  Physical memory: 1014 MB
  Minimum graphics memory: 8 MB
  Maximum graphics memory: 224 MB
  Used graphics memory: 11 MB
  Processor: x 86 family 6 model 8 Stepping 14
  Processor speed: 1596 MHZ
  Vendor ID: 8086
  Device ID: 27A 2
  Revision of the device: 03

  * Accelerator information *.

  Accelerator in use: Mobile Intel(r) 945 Express Chipset Family
  Video BIOS: 1264
  Current-mode graph: 1 440 x 900 true colors (60 Hz)

  I want to know, can I extend memory graph, it is very less compared to the total available memory, and I think that because of that I can't play most of the games. Please tell me is this the reason of not running games or I need some other additional graphics card or I can increase the graphics memory?

  Memory setting will not help. You have an integrated video card that is not designed to play 3D games. Since you have a laptop, you can't change that. MS - MVP - Elephant Boy computers - don't panic!

• Problem with NQS_PASSWORD_CLAUSE block of initialization

  I try to use the NQS_PASSWORD_CLAUSE in my block of session for authentication of the user's initialization. I query a table called bi_auth_table, which contains the bi_user and bi_user_pw columns.
  
  Here are my source of block initialization code:
  
  Select bi_user from global_admin.bi_auth_table
  "where bi_user = ': the USER"
  NQS_PASSWORD_CLAUSE (and bi_user_pw = ": PASSWORD '") NQS_PASSWORD_CLAUSE
  
  When I test the block of initialization in offline mode, I am prompted for USER and PASSWORD. When I enter values and run the test, I get this error:
  
  [nQSError: 17001] Oracle error code: 933, message: ORA-00933: SQL command not properly finished the call of the OCIStmtExecute OIC.
  [nQSError: 17010] Prepare the SQL statement failed.
  
  Any ideas?

  Try without space after the clause NQS_PASSWORD_CLAUSE as stated in the Manual:

  NQS_PASSWORD_CLAUSE (and pwd = ": PASSWORD '") NQS_PASSWORD_CLAUSE

• Table of waveform LabVIEW 2009

  I have a problem with the table of waveform in LabVIEW 2009, the chart will not poster on the table after a few iterations. This is a bug that appeared in LabVIEW 2009. The same program worked well with LV 8.6. Does anyone know a work around for this problem? I am currently using Version 9.0f2

  See the attached diagram

  It's strange...

  I checked that save this return to 8.6 does indeed.

  If you replace the function Merge signals with a bundle of things function seem to work fine.

  There is also something weird happens with the property node. If you start with a pnode for active track, then drag it down to add another element, then change this new element to draw colors, you get an error on the property node.

  

  "Interesting."

  Steve

• problems with my Tungsten E2 Palm reading is not my memory card more

  I have a Palm Tungsten E2 and I now have problems with him reading the memory cards and I don't understand why because it was very good.  I didn't give up, nothing happened.

   

  I have a 1 GB memory card that I use.  It's a SD Impact memory card

   

  When I insert card it makes no noise and if I try to format the card it says No card inserted.

   

  I also tried a new card, it's a 2 GB Sandisk card (did not know at the time that it would use only a 1 GB card).

   

   

  Hope that was enough information for you help out me.

  My only other suggestion right now would be to try another 1gig or smaller card to determine if the card is at fault.

  I had 100% success with SanDisk cards.

  WyreNut

  Message relates to: Centro (AT & T)

• Problem with VeriStand deployment on cRIO-9074

  Hi all

  I'm playing with VeriStand 2010 and my cRIO-9074. I'm just trying to deploy a very simple application of VeriStand on the cRIO, but I can't get VeriStand to connect properly to the cRIO. I get error 63. Would it be a problem that the cRIO is configured using LabVIEW 2009 and I use VeriStand 2010? Glancing at the MAX software on the cRIO contained NOR-RIO 3.4.0 (minimal) that contains time LabVIEW Real 9.0.1.

  Any other ideas?

  Concerning

  Martin

  In the Add/Remove programs for your cRIO in MAX dialog, you will also need to select custom Setup to see the installation component VeriStand engine.