Problem with setting window of acquisition on 1429 PCIe capture card

Hi all

Recently, I am using the Basler A504k camera with card PCIe-1429 of goodwill for the acquisition of images at high speed. I found problems with setting the acquisition window in the capture card using Measurement & Automation Explorer.

1. for example, if the size of the original image is 1280 * 500, if I put the window of acquisition with left 0 and width 1280, everything is OK, but if I set the width to 1279, there will be an error (error 0xBFF6002C FIFO overflow caused the acquisition of stop), if I set the width multiple of 8, there was no error. Could someone tell me why in this case, is it because the packet data transfer for acquisition card rule?

2. the window of acquisition is set according to the camera image, right? If the camera has also a function of area of interest, the acquisition window setting is always the image coming from the camera.

Attachment is my setting a MAX software.

Thank you very much

Hi xiaochunfly,

My bet is 1280 pixels image size is aligned on 32 bytes, and the material may actually go from line to line without breaking the transfers. With the width of the non-aligned countries, he needs to start a new transfer on each line, and this has an additional load on the PCIe bus and the system memory bus. Currently infrastructure IMAQ trying to adjust to any size of border/size possible image regardless of efficiency, it take the material and changes in recent processor Intel chipsets have reduced effectiveness with system memory bus performs under these conditions. So, you can get much better performance if you use line widths. You can also get the latest IMAQ driver because there was changes in the latest few transfer more effective under some of these conditions.

AOI is usually under the framegrabber. If you reduce the AOI who sends the camera, it seems often identical to the framegrabber as if you just had a camera with a smaller sensor. Thus, your AOI in IMAQ must be set to the size of that the camera is sending, unless for some reason you want to capture less of what the camera is able to set up on its own.

Eric

Tags: NI Hardware

Similar Questions

  • iTunes update errors with the following message appears: there is a problem with this Windows Installer package. A program run as part of the set up did not complete as expected.

    iTunes error update

    I am trying to install an update to iTunes on my laptop and find the folowing part-way through the installation error:

    "There is a problem with this Windows Installer package. A program run as part of the set up did not complete as expected. Contact your provider to support personal or package. »

    I got iTunes for 3-4 years now and have always been able to install updates successfully, so don't not sure what is the problem.

    I tried msconfig and changed the boot process, so it includes all of the non-Windows elements, as suggested on the Microsoft Web site, but that has not worked.

    Can anyone help?

    Thank you

    The instructions were to contact the vendor of the package. This isn't iTunes, Microsoft.

    Ask the question in the Apple Forums:
    https://discussions.Apple.com/index.jspa

  • Windows Installer error there is a problem with this windows package install. a program run as part of the set up did not complete as expected "during the installation of Itunes

    Original title: problem WIndows Installer to install the latest version of i tunes

    When I try to install the latest I tunes version 10, I get a message "there is a problem with this windows package installer. a program run as part of the set up did not complete as expected "the downloads version, but will not be installed."  How can I fix?  I have an earlier version, but I need to update to use my i pad.

    Hello

    You can try the steps of troubleshooting provided in the link below and check if the problem persists.

    Problem installing iTunes or QuickTime for Windows

    http://support.Apple.com/kb/HT1926

    To get help on the issue, you can get in touch with support for ITunes.

    http://www.Apple.com/support/iTunes/

  • Error 1720. There is a problem with this windows package install.

    Can I uninstall the Ask.com a toolbar script

    Philip black [09:46]: Error 1720. Contact technical support staff or the seller-impossible packaging run vbisff open uninstall script error-not found script path?
    There is a problem with this windows package install.
    I can't uninstall the Ask.com toolbar script and program icon I
    E-mail address is removed from the privacy *.

    Hey Thechiflows,

    Welcome to the Microsoft Answers Forum!

    Step 1:

    To get rid of this error, I suggest you to install the latest version of Windows Installer, which you can download from the link:

    http://www.Microsoft.com/downloads/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

    Step 2:
     
    Start the Windows Installer service.
     
    1. Click Start, type Services.msc and press [ENTER]

    2. double-click on Windows Installer.

    3. set the Windows Installer to Manual startup type.

    4. Click Start to start the service. Note the error message, if any.

    5. click on OK.

    Step 3:

    The Windows Installer CleanUp utility deletes all files and registry settings associated with the configuration of Windows Installer of a program.

    Read the following article which talks about the description of the Windows Installer CleanUp utility:

    http://support.Microsoft.com/kb/290301

    Let us know if the steps above will help.
     
    We look forward to hearing from you.

    Kind regards

    Manasa P-Microsoft Support

  • There is a problem with this Windows Installer package.

    There is a problem with this Windows Installer package. A program run as part of the set up did not complete as expected. Contact your provider to support personal or package. I received this error when you try to install the software for a Scanner to deposit check fast Chase Bank.

    Hello

    I suggest you try the steps below and check if it helps:

    Step 1: Verify that the Windows Installer service is running or not

    Start the Windows Installer service.
    1. Click Start, type services.msc and press to enter.
    2. from the list of objects, double-click Windows Installer service.
    3. change the startup type to automatic and click on the Start button to start the service.
    4. click on apply and then click ok.

    Check whether the problem is resolved.

    Step 2: Unregister and register the Windows Setup program again

    1. click on Start Orb, in the search box of start, type MSIEXEC /Unregister. and then click OK.

    2. click on Start Orb, in the search box to start, type MSIEXEC/REGSERVER, and then click OK. After you run this command, the operation is complete.

    3. now try again to your installation.

    More information: How to troubleshoot issues that may occur when you install, uninstall, or upgrade one program on a Windows computer

    Hope this information is useful.

  • Impossible to uninstall Apple Software Update program, get the error "there is a problem with this Windows package install."

    I need to uninstall the Apple software update program, but cannot.  Message reads as follows: "there is a problem with this Windows package install."  A requirement of the program to complete this installation could not be executed. Contact your provider to support personal or package.  I have Windows 7 Professional.

    I need to uninstall the Apple software update program, but cannot.  Message reads as follows: "there is a problem with this Windows package install."  A requirement of the program to complete this installation could not be executed. Contact your provider to support personal or package.  I have Windows 7 Professional.

    Hi, CA Bill.

    Start the Windows Installer service.

    1. Click Start, type Services.msc and press [ENTER]

    2. double-click on Windows Installer.

    3. set the Windows Installer to Manual startup type.

    4. Click Start to start the service. Note the error message, if any.

    5. click on OK.

    Start uninstalling software Apple

    If the above fails, use CCleaner uninstaller

    http://www.Piriform.com/CCleaner/screenshots

    See the help link - below
    To remove, and then reinstall iTunes to windows 7.

    http://support.Apple.com/kb/HT1923

    Web site support Contact Apple for additional assistance on the issue:
    http://discussions.info.Apple.com/index.jspa

    OR http://www.Apple.com/support

  • When I try to install an update to iTunes on my Windows 7 computer I get the following message: "there is a problem with this Windows Installer package. A program required for this install to complete could not be run. "Help, please.

    When I try to install an update to iTunes on my Windows 7 computer I get the following message: "there is a problem with this Windows
    Installation package. A program required for this install to complete could not be run. "Help, please.

    Hello..

    Try this support article > If you see an error message "Windows package install" when you try to uninstall iTunes from your PC

  • I am trying to install an update to iCloud on my Win 7 PC and I get an error message that there is a problem with my windows install. How can I solve this problem?

    I am trying to install an update to iCloud on my Win 7 PC and I get an error message that there is a problem with my windows install. How can I solve this problem?

    Hello grandpa_bill,

    Thank you for your participation in the communities of Support from Apple.

    If you get an error when you install an update to iCloud for Windows, try to download the latest version of download iCloud for Windows.

    For more information, see get help using iCloud for Windows.

    All the best.

  • There is a problem with this Windows Installer package. A program required for this install to complete could not be run Windows 10

    There is a problem with this Windows Installer package. A program required for this install to complete, could not be executed. This appears when trying to update

    Repair Apple Software Update of programs and features, Control Panel, and then try again.

    If not for general advice see troubleshooting problems with iTunes for Windows updates.

    The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach. Review other cases and a list of documents to support further down the page, in which case one of them applies.

    More information area has direct links with the current and recent if you have problems to download, need to revert to a previous version or try the version iTunes for Windows (64-bit-for old video cards) as a workaround for the problems of performance or compatibility with third-party software.

    Your library must be affected by these measures, but it is also related to backup and recovery advice if necessary.

    TT2

  • I tried to update iTunes on Windows 10, now, I get the error "there is a problem with this Windows Installer Package".

    Hello

    I tried to update iTunes on Windows 10 and now I get the message error "there is a problem with this Windows Installer Package".
    I tried to fix it too, but it has not helped, so I uninstalled and tried to reinstall but there has not helped either. I tried almost everything I've seen in other posts.
    I use a laptop Asus series k55VJ with an original copy of Windows and has never had this problem before.

    Any of you have an idea what can do?
    Thank you!

    Try to repair the Apple Software Update of the programs and features Control Panel, then uninstall it and then reinstall iTunes.

    For general advice, see troubleshooting problems with iTunes for Windows updates.

    The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

    Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

    More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

    Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

    TT2

  • Anyone know if there is a problem with the "Windows Update" site? Since May 11, 2010...

    Anyone know if there is a problem with the "Windows Update" site? As of May 11, 2010 I could not access it for 2 days now.  I get an error report indicating that he has a "problem with the site '... Not sure if it's my computer or the site itself. I just need to check updates and download them. I would be grateful for any feedback...  Thank you!
    ~ Jenifer

    It is without a doubt.  There were a few patches published today, and I was able to update all my machines successfully.  This looks more like a virus problem.  Have you run a virus scan recently?  Many times, if you are infected the virus will prevent you to access Windows Update.

    You can also use Microsoft Fix It to reset the Windows Update components: http://support.microsoft.com/kb/971058.  This could also be your problem.

    Let me know how it goes,

    Barbara

  • have a problem with my Windows Services.

    I have a problem with my Windows Services.
    Every time when I run the Windows Services window, I get a warning:

    One or more activex controls could not be displayed because that is:
    1. your current security settings prohibit running activex
    the controls on this page, or
    2. you have blocked an editor of one of the controls.
    for example, the page may not display correctly.

    The warning popup opens only when I click on the extended tab.
    The problem has nothing to do with the security of IE, because I can open pages with ActiveX controls on them and so.

    I installed the Spybot spyware/malware removal tool. Then uninstalled.
    I don't know if this is the cause of the problem. But I assume that it is.

    So, maybe someone faced the same problem and knows the cause for it.

    Thank you.

    Hi faisalzaman,

    Check out the link below to put on with similar problem and check if it helps.

    http://social.technet.Microsoft.com/forums/en-us/w7itprosecurity/thread/90c3202c-448B-42b7-ACF7-dab8dba7b000/

  • When I try to load Quicktime I get "Quicktime for Windows. There is a problem with this Windows Installer package.

    Original title: I'm loading Quciktime.

    When I try to load Quicktime I get "Quicktime for Windows. There is a problem with this Windows Installer package. A program required for this install to complete could not be run. "How to do this?

    Hi Tonyb13apb,

    ·         The issue is limited only during the installation of QuickTime?

    ·         Did you do changes on the computer before the show?

    Follow the suggestions below for a possible solution:

    Method 1: Uninstall and reinstall QuickTime and check.

    http://support.Apple.com/kb/HT1925

     

    Method 2: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

     

    Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    a. click Start, select run.

    b. type msconfigand click OK.

    c. the system dialog Configuration utility appears.

    d. click on the general tab, click Normal startup - load all services and device drivers and then click OK.

    e. When prompted, click on restart to restart the computer.

    If the problem persists, you can contact Apple support for more help and information.

    http://support.Apple.com/kb/HE57

    Let us know if it helps.

  • Disabled the HTTPS option in Hotmail and problems with the Windows Firewall, Microsoft Security Essentials and Windows updates.

    Original title: Windows Live Hotmail only opens a new window links e-mail composition!

    I recently put my Windows Live Hotmail account to my default e-mail client in Internet Explorer 8 on my Windows XP SP3 System. Unfortunately, whenever I click on a link to e-mail on a Web page to open a new message, Hotmail tells me, "Sorry, there seems to be a problem with Hotmail right now", and a new/compose message window does not open. I disabled the HTTPS option in Hotmail, which fixed the problem. However, when I went to do a manual update of Windows, I am nailed with a Trojan horse! Apparently, the Windows Firewall and Microsoft Security Essentials have been affected by turning off HTTPS in Hotmail! It's 2012, and it's terribly disappointing that Microsoft only has not ironed out all the imperfections in these services now. If anyone can give me a solution (in simple terms), I would appreciate it!

    Thank you

    Ryan

    Hi Ryan,

    1. you receive messages or error codes when you access Windows updates?

    2. what happens exactly with the Windows Firewall and Microsoft Security Essentials?

    About the update of Windows, the Windows Firewall and Microsoft Security Essentials issues, you may try to launch the FixIt and see if it helps:

    Method 1:

    Resolve security issues to protect and secure Windows automatically

    The problem with Microsoft Windows Update is not working

    Method 2:

    You can also refer to article and perform a full scan on your computer by using the Microsoft Safety Scanner.

    Microsoft safety scanner

    Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

    On the Windows Live Hotmail account, you can publish your request in instances of Windows Live to get help:

    http://answers.Microsoft.com/en-us/windowslive

  • When installing iTunes I get a message error "there is a problem with this Windows Installer package. A program required for this install to complete could not run. »

    Windows Installer package error

    When installing iTunes I get a message error "there is a problem with this Windows Installer package. A program required for this install to complete could not run. "I downloaded Windows Installer 4.5, rebooted and tried again with the same results.  How can I fix?

    Hello

    Important The Windows Installer Cleanup (MSICUU2.exe) utility that was previously referred to as in this article has been abandoned. Although the Windows Installer Cleanup utility solved a few problems installing, it sometimes damaged other components that have been installed on the computer. For this reason, the tool has been removed from the Microsoft Download Center. program install and uninstall problem solving

    (http://support.microsoft.com/mats/Program_Install_and_Uninstall)

    is a replacement for this utility.

    "The problems with programs that cannot be installed or uninstalled.

    http://support.Microsoft.com/mats/Program_Install_and_Uninstall

    @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

    And see if this information helps you install iTunes:

    "Not to install iTunes or QuickTime for Windows"

    http://support.Apple.com/kb/HT1926

    «Remove and reinstall iTunes, QuickTime, and other software components for Windows Vista or Windows 7»

    http://support.Apple.com/kb/HT1923

    If the advice already given does not, please contact Apple for assistance.

    "iTunes support-how to use iTunes.

    http://www.Apple.com/support/iTunes/

    "Contact iTunes Support.

    http://www.Apple.com/support/iTunes/contact/

    Or ask in the community Apple iTunes:

    https://discussions.Apple.com/community/iTunes

    See you soon.

Maybe you are looking for