Problem with signal sony z2

Similar Questions

• Problems with signal followed during sampling of the signal

  Hello

  I'm relatively new to LabVIEW 8.0 and I'm having a problem with being able to monitor the signals that I am gaining two simultaneous analog signals.  I have the user to input the frequency of sampling and the length of the sample, and then I starts the scan, but when running the analysis, I don't see no result on the chart if the duration of the sample is passed, at which point all data comes.  Previously, I could see the acquisition of real-time data and I don't know what I've done since then have possibly that stop working.  I tried to introduce a kind of late for may allow the software to apply the data to the graphics, but I had no success.

  I have attached the VI of the data acquisition component.

  Thank you so much for reading this.

  Hello

  I suggest you try these two options:

  1. in each iteration of the while loop, add your data to the data of the previous iteration, IE use a shift register to create an Adrien to data that you have acquired. When you save the data in a file, read data from the table and not the current value of the waveform. You can read the data in the table by using a queue, or by using any simple method to pass data between the blocks.

  When you use a local variable of the waveform card, you only read the current value in the array, not its history.

  2. use a property of waveform graphs node to read the history of the ranking, convert the picture from picture to picture 1 d 2D using cluster of waveform ungroup functions and write to the file, click on "Save".

• Problem with the Sony Bravia KLV-32T550A color

  My Sony Bravia KLV-32T550A (Serial No. 6165091) which is about one and a half years began to have problems with color. When you turn it on, it turns red and then the colors are all stripped top and blurred. After now for a few minutes, the color is back to normal, and then it goes bad again after a few minutes. An authorized Sony technician came to my place and told me immediately that this is a problem with B motherboard and it must be replaced costing me about 5500 rupees as well as Service charges. Please indicate if the technician diagnosed the problem correctly and this card cannot be fixed first to solve this problem of color instead of such a costly replacement.

  Thank you for your message and welcome discussion of the user forums.
  According to the description of your problem, the B-board (motherboard) is normally the root cause of the problem.

• Problems with webcam Sony Vaio S series?

  I was on Skype and my camera suddenly stopping.  I thought it was the other camera people, but it was definitely mine.  And now even the program Silverlight do not recognize.  Anyone else had problems with the webcam?  Someone at - it solutions?

  Jman187,

  If you want to do a restore of Windows, follow this here.  If you want full restoration factory (deletion of data), then follow this link using F10 or this link using the Assist on Windows 8 unit button.  As a precaution, you should backup your data...

  If my post answered your question, please mark it as "accept as a Solution.

• Satellite L670-153: problem with a SONY 4 GB mass storage

  I have a portable satellite L670-153 with Windows 7 64 bit. When I conect a 4 GB SONY USB mass storage, Windows install the USB mass storage. But after a few minutes, the USB mass storage is disassemble and assemble and disassemble some indefinitely.
  I update the bios and the driver from the chipset, but I still have the problem.

  And what now?
  You can test the functionality with the other 4 GB USB key? Just to see if other brands will be recognized correctly. The problem when used on another PC with the same operating system?

  I have 2 SanDisk and 1 stick USB Toshiba and each of them are recognized properly on different laptops?

• Only problem with VISTA (sony vaio VGN-FW375J)

  Hi guys... I hav a unique problem... I have sony vaio (VGN-FW375J) with drive HARD 320 GB, partitioned into C: (108 GB) drive, drive (60 GB) D: and E: (GB 118) drive, just around 286 GB... This means that I've lost almost 34 GB (I dono how to recover the 2 rear)... share form what I have 3 folders on all drives (autorun.inf, comment.htt, and desktop.ini) which am not able to remove 2... Thirdly, I have a unique problem, where in my free space (30 GB) in C: drive only 15 GB... I dono what happened to the other 15 GB... KINDLY HELP...

  Hi shiva55,

  Check to see if the following is useful.

  Method 1: Try to perform a disk cleanup and check if it helps.

  Delete files using disk cleanup

  Some of the files you are referring are system files that are required by the operating system, and you will not be able to remove them. But there may be malware infection as well.

  Method 2: Perform an online scan to find any infections on the computer.

  For Windows Vista and Windows 7 security scanning

  Malicious software removal tool | Protect your computer

• New Dell Inspiron 1764: Problems with signal low connection to wireless networks.

  I have a new laptop Dell Inspiron 1764 I received on 25 June. It is "replace" a Dell Inspiron 9100, who has learned to be too slow and too bulky for my needs. For the purposes of support, the two laptops are running on Windows 7.

  Overall, I love my new Inspiron 1764. However, I noticed the connection/signal strength seriously degraded, with wireless (Dell Wireless 1397 WLAN Mini card) card, compared to my Inspiron 9100 (Dell Wireless 1350 WLAN Mini-PCI card).

  In areas of my home that my 9100 can obtain the power of the complete signal (5 bars), my new 1764 bars 2 or less. This behavior is not as limited to only my house as I have tested in my work and in an area of less than 10 feet away from the wireless router, I have 'Internet connectivity problems.

  I tried twice this morning talk with Dell technical support. The first person I talked to tried to be helpful and initiated at least a DellConnect session with me so that he can check out some of my settings and such (However, why they went twice in my sharing settings I could not determine as they have absolutely nothing to do with the intensity of the signal).

  Unfortunately, I was disconnected from the session when I went to a place that had less signal than just next to my wireless router.

  I then go on the chat support with Dell and received another technician to speak with. I explained my problem, told them that I was in a DellConnect session with the other technician, and they looked to the top of my support contract.

  They then told me that my warranty does not cover software issues and referred me to the software Department and said it would be a supplement. I told them that I did not believe that it is a problem of software in any way, shape, or form. They told me that it must be a matter of adjustment. I spent several hours scouring the internet forums on Dell and other sites check those who have had similar problems. Some of their questions were certainly the software settings, but I still don't yet to find anything that tells me I have an incorrect setting of software.

  So far, I'm standing in my kitchen, tapping on my Inspiron 9100 with a full 5 bars, while my Inspiron 1764 is sitting next to me with a skinny 2 bars, and I am literally standing 7 feet above the room which houses my Linksys WRTU54G-TM router.

  Personally, I suspect a faulty wireless card, but how to convince Dell to hear my case and replace it instead of trying to bilk me for support of useless software?

  I hope Dell Tech Support bed actually this post, or people with the same problem can Dell refer to my previous post describing the problem and the fix.

  It IS a PROBLEM of MATERIAL WITH the ANTENNA, AND VERY PROBABLY THE DIFFERENCE BETWEEN a DECK CONNECTION at the ANTENNA of the PLATE, from connections TAPE FOIL INDIVIDUAL at the ANTENNA of the PLATE, THAT DELL MUST HAVE RESPONSE BETWEEN WHAT MINE PORTABLE has BEEN CARRIED OUT AND THE SPARE ROOM WAS MADE. THE PROBLEM IS NOT SOFTWARE, PROVIDER OR ROUTER, IT IS THE PLASTIC WITH THE ANTENNA CASE!

  Dell is in fact losing more money with the hours of technical support through software patches and sending technicians with new wireless cards that does not solve the problem. They need to send and replace the plastic case behind the LCD screen with the updating of antenna and connections.

  Good luck!

• Problem with signals TTL metering: confused with counting

  Hello

  I use a TTL of 0.2 Hz signal to synchronize two devices. I use a Usb-6210 card to count the pulses TTL. The meter goes off when it detects the edges increase. In my case, the meter was sometimes triggered at low altitude, which causes wrong results (see attached pictures, the TTL signal is sampled at 20 Hz and the dots represent an increment of the counter). How can I solve this problem?

  In addition, the cable that connects the TTL output was welded by myself, would that be a problem of bad contact?

  Thank you very much

  K-X

  What is the nature of the device producing the TTL trigger signal?  Is it possible, for example, that it could produce a 1 microsecond pulse (which might not be visible on your signal ground) that would trigger the meter?  You really produce a digital pulse (i.e. your something circuit which is 'on' or 'off' as opposed to 'product analog voltage in the range of 0 to 5 volts')?  Are there any other devices around that could produce the impulses that are "picked up" by your meter?  The cable connecting the TTL is armored pulse for the meter?  The shield is based at one end?

  These questions (and the previous) suggest that the problem may be 'electronic' rather than 'LabVIEW '...

• Problem with the Sony ARW in CS2 files

  I have a Sony A350 and have recently decided to switch between using the camera ARW files in my Photoshop CS2.  Unfortunately when I try to open them I get this message "could not complete your request because it is not the right kind of document.  I had the 'Help' menu and ran "updates... "The first time that I have updated I did so that the box asking if I wanted to update Camera Raw 3.7 has been activated (which, I understand, should have set).  So, even after installation of the update are why my ARW files is still not recognized?  I am very confused and would appreciate any help.

  Unfortunately for you the ARW files from your camera need ACR 4.4 or higher.

  It will not work with CS2.

  You must upgrade PS CS5 or use the DNG Converter * to create editable in you files earlier.

  http://www.Adobe.com/products/DNG/

• Problem with my Sony DSLR A100

  I don't know if this is the right place to post this, but here goes.

  My camera won't take pictures when I press the button and the display flashes when I try.

  Is it broken, what I have to do to fix it?
  I have also restarted the camera, and who did nothing.

  If you can help that would be great, thanks.

  Hello
  Welcome to the forums.
  If you see a flash (image disappears briefly) when looking through the viewfinder, it is most likely a speed of slow shutter or collage. You may need service. Please contact support for deeper troubleshooting.
  http://eSupport.Sony.com/us/Perl/suppor... l = DSLRA100

• am having problems with my sony vaio to adapt, there are circles on the touchscreen messing around.

  for some reason, there are circles on my sony vaio, made the touchscreen does not work as usual. I think I activated some kind of contact for assistance. How can I disable it?

  Hi shameo

  When was the last time it worked correctly? Have your tried to calibrate your touch screen?  You can try to

  Remove the display driver from the Device Manager, and then restart your computer.  When the computer restarts, the operating system will find the device and re install the appropriate driver.

  If my post answered your question, please mark it as "accept as a Solution.

• Problem with signals slots ToggleButton

  Trying to connect a signal to a slot:

  connect(myToggleButton, SIGNAL(checkChanged(bool)), myDataClass, SLOT(setMyValueOn(bool)));
  

  In myDataClass.hpp:

  public slots:
    void setMyValueOn(bool valueOn);
  

  In the cpp file:

  void MyDataClass::setMyValueOn(bool valueOn)
  {
    // never called
  }
  

  I have the MyDataClass is a subclass of QObject and Q_OBJECT at the appropriate place in the file of the hpp.

  I think that I incorrectly use the toggle switch.

  The signal is called checkedChanged (bool).

  BTW, I suggest using Qt Creator, if you develop mostly in C++. It has the very practical signals AutoComplete functionality.

• problems with signal activeTabChanged

  Hello

  Ive tried to trigger an action when some tabs are launched for this that I though "Hey the activeTabChanged signal is perfect!", but for some reason any (I may implement the wrong way) it ever triggers the signal.

  That's how I apply:

  QObject::connect (tabbedPane, SIGNAL (activeTabChanged(Tab*)), this, SLOT (sectionTriggered(Tab*)));

  void App: {sectionTriggered (bb::cascades:Tab * activeTab)}

  activeListURL = activeTab-> objectName();

  getList();

  }

  Am I missing something? I have debug and put a breakpoint in the slot, but he never reached the point...

  OK, I found that the solution just had to connect the signal like this:

  QObject::connect (tabbedPane, SIGNAL (activeTabChanged(bb::cascades::Tab*)), this, SLOT (sectionTriggered(bb::cascades::Tab*)));)

  (including the "bb::cascades:" part) even though the qde described it as an error...

• I have a problem with the touch screen of Sony.

  Original title: "Sony touchscreen issues."

  I am running Windows 7 Home Premium on a Sony All In One with touchscreen. For about 4 weeks, I got a problem with weird things happening on the screen. For example, I can use any application and it will automatically become minimized and I'm now looking at the level of the office. Other times on keyboard screen will appear in itself. Do not know what is happening, but it sure is frustrating the heck out of me. Answer from Sony is that I put the computer back to factory settings, thus losing my files and programs. Is there a way I can back up the system and retrieve my programs from the backup. I don't know if I can find my original downloads, including Office 2010.

  Thanks a lot for your help.

  Dennis

  Hello

  IAM having the same problem with my Sony all in one touch with Windows 7 home Premium edition running, did you get your problem solved, please let me know what I need to fix, it is very annoying to use the computer now that the application itself minimizes every minute.

  Help, please

  -Irshad

• Z3 problem with WIFI

  Hi guys,.

  for two days now I m having a problem with my sony Z3

  whenever I connect my phone to the WIFI chip of the speed of the internet to all other devices connected to the wifi (telephone, laptop, satellite receiver)

  Once I have disconnected my phone's WIFI everything back to normal

  I tried to check if there is any application that puts internet buffer in memory but cannot find anything

  Please guys I need help

  EDIT: both bad guys I solved the problem

  I restarted the phone on safe MODE and everything went well so I knew that it is one of the applications that I have installed so I dsintall some of them and boom the beautiful hope work someone found this useful

  @uliwooly
  Just try to restart in safe mode and test the wifi
  If all goes well then you can have an app of malware causing the buffering of the Internet
  Uninstall the last app u just installed and it can solve the problem