Problem with SlingTV through Airport Extreme?

Similar Questions

• Can I use old time capsule for storage only with a new airport extreme (standard want latest HQ)?

  I have a time Capsule elders (802.11n). I would like to know if I can still use this time Capsule only as a network storage device, if I decide to build my network with a new Airport Extreme (802.11ac). If I can do that, how would I set up the network to continue automatic backups with a router to update?

  To do what you want, the new AirPort Extreme 802.11ac would be installed as the "main" network router The time Capsule would be connected to the AirPort Extreme, using a wired Ethernet cable connection, and the time Capsule should be configured to run in bridge with the service Mode Wireless off.

  Any Mac you want to save in the time Capsule would need to have Time Machine preferences on each Mac adjusted to ensure that the time Capsule has been set as the target for backup.

  If you decide to add the AirPort Extreme, post back for more information at this time, if you need installation instructions step by step.

• Solve a problem by getting an Airport Extreme to join my network.

  Greetings,

  I have a WiFi network, consisting of a router TimeMachine (primary Base Station), the AirPort Extreme Base Station and expansion of the Airport Express network

  I receive notification messages for these devices utility AirPort (Enter Password) - probably updates lately.  I do not know the passwords for these devices because I've had them so long and after initial installation and many updates of OS X I couldn't find entries for them in Keychain Access.

  Today, I made an attempt to reset the Airport Extreme to try and go through the installation routine and have the opportunity to create a new password and save it.  First of all, I did a soft reset and then tried a hard reset.  The results were the same for either - one error as follows...  Airport Extreme fits factory currently.  It is plugged in and running with a light orange blinking.  She appears in the WiFi menu as a new Airport base station.  Selecting menu launches Airport utility and a dialog box drop-down connection.  The dialog box States "collecting information on your network - preparation, Joining Airport Extreme and finally"an unexpected error has occurred, try again"there is a very brief message (.5sec) before the last error - try again.»  In my view, that it is said 'Extreme Base Station on your network'.  This could mean that because the TimeMachine works as the main base station, the Airport Extreme Base cannot be joined so that I can Setup/modify it.

  Ultimately I'd like to get the issue resolved for all three devices password, but I'm a little gushy now after this attempt

  Someone has an idea how to proceed.

  Thanks Dave

  There are several things going on, but you can fix pretty quickly is the password. It is a piece of information that you should really have - now and for the future. You can reset your password by sticking the end of a paper clip in the back of the airport for more than ten seconds. You will see the configuration on the Airport utility screen. Do not forget your password in the future.  At the end of this operation, you can see a firmware view - to take care of that.

  Once your airport is reset, and the password is updated and updates, you can see if there are any problems - if any. If there are additional questions, you can include a photo of the Airport utility screen.

• What should I wear to the front with ATT and Airport Extreme?

  I have AT & T Uverse with an Airport Extreme.

  EI is implemented as a bridge, because it wouldn't work otherwise.

  I went into the game/NAT on the router/modem ATT layout and tried to activate some ports to forward.  Then I check the port and find that it is always closed.

  Someone here would be able to offer assistance with problems?

  I do this to try to send large files to a friend VIA files torrent based, although it does not seem to allow me to seed.

  Before ATT I got time warner and my own modem and router combo, and it works wonderfully in this configuration, so I can only the assertion that the issue is somewhere in the new place from the material.

  Now, if I try to download a standard torrent, I have no problem, but try to make my own with the trackers who have worked before, there is no dice.

  Thanks in advance for any help.

  ATT system is the NVG599 of ARRIS

• Please help me with my Apple Airport Extreme

  Aabout 2 weeks ago, we had a storm really come through the East Texas up to this point my router was working fine. The first week, I called and my ISP said that we had a power outage in the area and I thought that I thought this would happen so I waited a week so that they could get that clears up and the fact that I was always getting internet was slow, but I was still getting service.  Next week I continues to check the speed of the internet, and it was still slow so I called the ISP and they said everything was good at the end there are so I hooked my book mac ylthe modem and tested it and I was getting high speed but when I connected it to my router it was lamentable, once again. Now, here's where it gets weird in the morning as around 05:00, I get great service, but when I come home it's crap. I called apple and talked to technical support and just tried what they suggested that they sent me a replacement and it does the same thing, I am at a loss and do not know what could do this I changed the network name where only my Mac has been on the network and no dice. I put in Bridge mode with Mac connected directly to the airport and he did good but as soon as it went wireless was not good! So guys and girls I know this is a long post and it is typed on my iPhone but do I just go and buy a new router or I can save this one, because I don't really like it. Thanks for your help, sincerely Josh

  We need more details.

  Who is your ISP? Cox in particular is having problems with IPv6. There is a long thread to here about it.

  This modem do you have?

  You can test the direct connection to the modem after you come home and give us the real speed test. Then, put the airport back and test again... show the actual speed.

  Even in the morning when the airport looks ok.

• Gigabit Ethernet through AirPort Extreme

  I just got a gigabit home connection. If I connect my iMac via ethernet to gigabit municipal internet provider modem, II can get about 800 Mbps download based on the file netspeed.com. Nice.

  However, when I use my Airport Extreme as a router ethernet (put the extreme between the iMac and the modem) my speed drops to about 1/10 of that.

  None of the devices that I currently own are capable of handling 802.11 ac, so I know I could not anywhere near gigabit wireless speeds. But it would be nice to have the fastest speeds on the one machine I intend to connect via ethernet, then connecy to the extreme wireless.

  Airport Extreme really limit the ethernet so? Is there a setting I can adjust for more fast ethernet routing?

  If the AirPort Extreme 802.11ac is configured as a DHCP and NAT router, then the WAN to LAN speed will be limited to about 300-400 Mbps.  Check the results here:

  http://www.SmallNetBuilder.com/tools/charts/router/view

  If the AirPort Extreme is configured in Bridge Mode, then you would expect to see 600 - 700 MB/s speed this way.

  http://www.SmallNetBuilder.com/tools/charts/router/bar/75-LAN-to-Wan

  If you don't see results, then the AirPort Extreme is not to negotiate properly with your modem speeds.  Unfortunately, Apple has removed all the settings to manually adjust WAN port on the AirPort Extreme 802.11ac speed, so there is not much you can do others try a few unusual things...

  One of them would be to insert a Gigabit Ethernet switch between modem and AirPort Extreme to see if it will negotiate better speeds like that

  Another would be to try an Ethernet cable between the modem and AirPort Extreme cross.

  If none of these things help, then you should ask Apple to replace the AirPort Extreme to you and hope for more luck in the next test.

• Sporadic problems with pdf through Citrix session

  We run Citrix XenApp 6.5 with the installed 15.10.20056 CD player.  Sporadically when we launch a PDF through our session, data will not show, but this is.  If you take the mouse and you're trying to highlight, it will then appear and be seen.  If this isn't the case, then the user does not know it is there.  This does not always happen however, and the text will appear without having to highlight something.  We have tried to disable scrolling smoothly and some other items made, but it doesn't seem to make a difference, unless there is a setting I'm missing somewhere?  Any ideas are appreciated.

  Hello

  We did some checking and looked for a solution.

  Finally, we found this setting here in the image:

  

  In our area is the problem with the display of PDF files in Citrix Envirement

  much better (.. maybe went) if we change this setting on "Immer" (always).

  Can check you in your area too?

  Thanks for your comments!

• Problem with Blackmagic DeckLink HD Extreme 3D and Premiere Pro CS 5.5.1

  Hello

  I'm having a problem with the first and Blackmagic DeckLink HD Extreme 3D. When I create a timeline of Blackmagic of any sort and I import a film and start working on it, everything works as expected and are quite fast. I can see the image in the window of my monitor and the output to the external display of JVC is excellent (SDI). If I create another new project and in there I create a regular first screening chronology (in this case to edit Canon 5 d MKII footage) I can also change without problem (and with even better named Update).

  The problem appears when I try to have a timeline for Blackmagic and a predefined regular creation timeline in the same project. If I create the chronology of Blackmagic first, I can import and edit, but at the moment I have create a first preselection timeline screen goes black for a second (which always happens btw) and then comes back again. So I can edit the first timeline screening perfectly but the chronology of Blackmagic image stopped appearing in the monitor window. I can play, I can hear and I can see it in the external monitor of JVC. But on the computer screen the only thing I see are images that paint on it and somehow stuck in there get it looks like some sort of overlay problem. After that if I close first he won´t close properly. I have to force it out. If I first create a first timeline preset that works just fine but when I create a timeline of Blackmagic this work won´t (the first timeline works fine)

  So, my guess would be that first pass to a certain color depth or space when creating a first screening chronology and for some reason any the Blackmagic card won´t adapt or update so I find myself with no picture and the remains of some images that I place on the monitor window area. I can see the scopes and all waveforms but not the video. Also perhaps monitors and display port adapters have something to do. I'll change soon so monitors would be nice to know if it's part of the problem.

  Any idea? Waiting to hear from Blackmagic too.

  My specs:

  MS Windows 7 64 bit SP1

  Card mother TYAN S7025

  Two-processor Intel Xeon X 5650 @ 2.67 GHz

  32.0 GB Triple-Channel DDR3 @ 533 MHz (7-7-7-20)

  Graphics NVIDIA Quadro 5000

  System drive: 125 GB KINGSTON ATA (SATA) Device

  The data disks: Seagate 2X1954GB (SATA)

  Seagate 2x977GB (SATA)

  External Lacie RAID 5 TB (for backups)

  My monitors are 2 Apple Cinema HD 1920 X 1200, connected via 2 ports of graphics cards.

  BTW, this problem appeared before the named Update.

  Thanks in advance.

  Sergio Rozas

  www.usert38.com

  http://blog.usert38.com/

  I had a similar problem with a Matrox card.  The solution was to turn on the composition of the bureau.  It is under properties - TAB, show - system on the 4th in the advanced settings list.  Some programs (for example AVID) insist on this being extinguished, but with CS5.5 I needed active.  I have not tested this with dark magic devices.  It don't has not caused me a problem with CS5,

• Problem with LAN Express airport

  Hello

  I recently bought an Apple AirPort Express router and I have several problems using the Ethernet with the most active airport. The thing is with my old router, I could have been connected to the ethernet cable, while at the same time connected with a LAN cable to my Macbook (end of 2015). The old router would have generated a wifi connection, but at the same time, would have enabled internet connection by cable to my Macbook without the active WiFi. People could use WiFi at home, but the Macbook would be connected to the internet by cable (lan cable connected to the router)

  My question is how to turn on a cable connection on my Macbook using the AirPort Express LAN cable, while at the same time, keep WiFi active. Currently, I have the ethernet cable connected to the airport and cable Lan also connected to the airport and the Macbook, but the internet will not work unless the WiFi is active. I would like to turn off the WiFi on the Macbook and always have an internet connection through the LAN cable that is connected between the AirPort Express device and Macbook.

  Thank you

  My question is how to turn on a cable connection on my Macbook using the AirPort Express LAN cable, while at the same time, keep WiFi active.

  Is the Terminal AirPort Express the only router in the current configuration of your network? No matter, what is the brand and model of the modem Internet you have the Express directly connected by Ethernet? ... or is the Express connected by Wi - Fi to the modem?

• Cat left on Xbox 1 with Cox and Airport Extreme

  Hi all

  I can't use the group chat.  He said "the only way to get my router to work with Cox had to define the link local IPv6 and to have a self assigned IP."  My NAN is set to OPEN, so it's not the problem.  I get this error code:

  0 x 89231806

  Configuration of the network block you chat away

  I opened the recommended ports and still does not work.  My router is set to DHCP and NAT. Can someone please?  Beyond frustrated!  Does anyone else have this problem?

  Thank you

  Heather

  Hello

  Your Question is beyond the scope of this community...

  I suggest that repost you in the Xbox Forums.

  "Xbox a Preview program FAQ.

  http://support.Xbox.com/en-us/Xbox-one/system/Xbox-update-preview-FAQ

  'Home'

  http://forums.Xbox.com/

  "Xbox forums.

  http://forums.Xbox.com/xbox_forums/general_discussion/f/3817.aspx

  _________________________________________________

  "Xbox Forums directory.

  http://www.Xbox.com/en-us/forums

  General

  • Home/FAQ/Forum policy

  • Community general discussion

  Material & Discussion Services

  • Equipment & Services

  Xbox support
  Agent hours: M - F 09:00-17:00 PT

  • Xbox 360 support

  • Xbox 1 support

  • Xbox on supported mobile devices

  • Xbox on Windows support

  • Networking of hardware information

  • Material information TV

  Law enforcement forums

  • Xbox 360 account Suspensions & Console bans

  • Account Xbox one & measures Console application

  • Announcement
    PLEASE READ. Introducing changes of case review & forum

  Technical support of Xbox Live rewards
  Xbox Live rewards Squad hours: M - F 09:00-17: 00 PST

  • Xbox Live rewards program announcements

  • Xbox Live rewards Questions

  See you soon.

• OfficeJet 8500 wireless printing through Airport Extreme = 'offline', how to fix?

  I know this question has been asked below, but it seems that everyone's situation is a little different.

  I have a MacBook using OS X 10.5.8.  I had this printer the other day & everything seems to go well except wireless printing (I can print with USB connected to the computer).

  The printer appears in Airport utility (and I even tried the remove all printers & add this a trick I've seen suggested in other posts) and in my programs as an option for printing but when I try to print wireless it says "offline".

  The printer is not 'asleep' or into hibernation or anything like that.

  Can anyone offer a solution that is not too technical? I know not all the computer jargon. Thank you! I intend to return it for the one with the wireless built in so I can't fix this pretty soon.

  Oh, the 909 a doesn't have wireless.  You plug it into your airport with an Ethernet cable.  It will automatically get an IP address when you plug it in.

• Problem with persistence through scenes

  I have a student who has created some code - see below. At the present time, this code is in Scene 5 - but the blocks will also appear on other scenes.

  1. How it not limit this code for just one scene?
  2. It can replicate this to be used on other scenes, but from fees.

  Currently, 50 blocks spawn above the other. They are used for teaching addition or multiplication. When they were dragged in a model, we do we want the model to another scene, that they on top of the other.

  The code is not too elegant, but it works except no repeats through scenes.

  Block =]

  This function creates a block at a given location and adds it to a table

  new identifiers are block30 and so on

  function spawnBlock() {}

  blockSpawn = attachMovie ("block", "block" + _root.getNextHighestDepth (), _root.getNextHighestDepth (), {50, _y:300}) _x:5;})

  Block.push (blockSpawn._name);

  }

  Does the funtion spawnBlock 50 times create 50 new blocks

  replace 50 the number of blocks as you want

  for (i = 0; i < 50; i ++) {}

  spawnBlock();

  trace (Block [i]); test if the funtion worked

  }

  function dragSetup (clip) {//this is used to assign a clip to funtion that can be reused with each block is created}

  clip.onPress = function() {}

  startDrag (this);

  }

  clip.onRelease = clip.onReleaseOutside = function () {//same as above}

  stopDrag();

  }

  }

  This allows each block that is necessary to drag

  Add more lines to let blocks more get dragged

  dragSetup (block0);

  dragSetup (block1);

  dragSetup (block2);

  dragSetup (block3);

  dragSetup (block4);

  dragSetup (block5);

  dragSetup (block6);

  dragSetup (block7);

  dragSetup (block8);

  dragSetup (block9);

  remains removed for brevity.

  use:

  function clear_blockF (): Void {}

  for (var i: Number = block.length - 1; i > = 0; i--) {}

  This [Block [i]] .removeMovieClip ();

  }

  Block.Length = 0;

  }

• Connection printer square with Hotspot and Airport Extreme

  Hello

  My family has a joint small pizza and I'm looking to switch our POS system instead. We do not have WiFi, so I was wondering if there is a work around to use the personal hotspot feature, set the AXE to "Join a wireless network" and then connect the printer to the back of the AXE to print receipts and also to use the cash register. This is the kit of POS of the place...

  https://squareup.com/shop/bar-restaurant-iPad-mini

  Maybe get WiFi would be the best solution, but I just wanted to see if this is possible. I have connected the AXE to the personal hotspot, but can not get the printer to be visible by the Setup program in the dashboard square app.

  Any suggestion is appreciated.

  Thank you!

  Your link does not work for me.

  You should be aware that Apple has removed 'join a wireless network' option... it no longer works in all utilities V6 later.

  Even if you use later hardware will not work...

  It works on older when equipment... It has an unpleasant effect...

  The airport becomes a silent client on the network... the ethernet ports have been disabled... the only access was wireless.

  I have connected the AXE to the personal hotspot, but can not get the printer to be visible by the Setup program in the dashboard square app.

  Nothing is plugged in by ethernet will work in this configuration. (USB might work if.)

  Apple authorizes the express be used as a wireless bridge. It is called client mode.

  AirPort Express: How to join an existing client mode - Apple Support Wi - Fi network

  However, you can buy any other brand wireless bridge... There is no reason in this situation to buy apple products.

• Problems with the Wi - Fi (Airport Extreme and At &amp; t Uverse questions)

  Hello

  We used an Airport Extreme with AT & T Uverse to our network wireless successfully since 2010. Recently Uverse sent me a new modem, and our wireless service has taken a turn for the worse. The network has two different wireless Internet for our House. Please let know us how we can solve this problem. We use a Mac, mac laptop 2, iPad 2 & all Iphones 2 are up-to-date with the latest version of the software.

  Mike

  The AT & T device is a modem/router that provides a signal of wireless network with a name something like ATTa1b3c3d, for example. Your AirPort Extreme also provides a wireless signal by using a wireless network name that you have assigned to the device.

  Thus, it would be normal for you to be able to 'see' the two wireless networks.

  If you don't want to not use the ATT Wireless, just ignore it... or... If you think that it is at the origin of the conflict with the wireless AirPort Extreme, it is possible to turn off wireless on ATT modem/router, so that you only 'sees' the AirPort Extreme network.

  AT & T support can help you in the task of turning off the wireless... or... If you have the number of brand and practical model of modem/router, AT & T, we can try to find an online configuration guide which could provide instructions for this task.

  If you encounter a different kind of problem, please provide details on the problem.

• Roaming network 3 Airport extreme

  Hello, this is my second post on the forum.  I have a roaming network 3 AirPort Extreme ACs.  (1) in the basement in the medium floor and a first floor on.

  Now middle and basement floor gives off a strong wireless signal and the home is wired with cat 5e if I have devices plugged into the extremes of import and everything works great.  However the AirPort Extreme is only releasing one, 9 Mbps wireless speed when other airports are clearing of 50-150 MB/s.

  I read on these forums that maybe my channels is getting mixed, but all adverse events are set to automatic for the channels so should I change that?

  Also when my new MacBook Pro connects to what is also a device to AC it still hangs to 9 mob/s.  Now it was getting a few days before when I had my time capsule base station wireless (n) with speed of 50-60, I know this isn't my Ethernet cable in the wall. all the recommendations I would appreciate your

  From your description of the problem, it seems that AirPort Extreme in question, is either misconfigured or is defective.

  I suggest that you first try a 'default' reset on this base station and then use AirPort Utility to set up your mobile network. If this fails to solve the problem, it may be defective and you need to replace.