problem with the pavilion dm4 3002 laptop drivers its

Similar Questions

• I have problems with the trackpad on my laptop Pavilion g6 (2012).

  I repeated my mouse HP remotely when you use this computer because I always found difficult to use trackpad. On the use of the touchpad, he sometimes goes out of control with the scaling and scrolling text selection. I checked the driver to find she had the latest recommended driver. I walked into its configuration in the control panel with the intention to disable but can find no choice. I need two points of orientation:

  1. are there clear instructions on how to use it? (still not found)

  2. How can I disable it if the first is not successful?

  Thank you for your attention in this matter.

  Hello

  Find your product on a laptop number:
  http://support.HP.com/us-en/document/c00033108

  Find your operating system:
  http://Windows.Microsoft.com/en-CA/Windows/which-operating-system

  In some models,.
  On your TouchPad, you will see a light in the upper left corner of your keyboard. The light is usually orange. If it is on, this means that the TouchPad has been disabled.
  If you look to the top left of your trackpad, there is a dash of small circle.
  Press twice on the circle to lock/unlock your trackpad.

  Below you will find a link on the troubleshooting of the TouchPad. Click on "Disable TouchPad" and see if it still register as disabled.
  It is specific to Windows 8:
  Use and troubleshoot the TouchPad-
  http://support.HP.com/us-en/document/c03523373

  If this does not work, use the link below. It is similar to the link I put in my post above, but it's for Windows 7:
  Use and configure the TouchPad Windows 7-
  http://support.HP.com/us-en/document/c01876141

  Kind regards

  Visruth

• sudden problem with HP Pavilion dv6-2157wm laptop

  Hello.  About 2 weeks ago, my laptop (a HP Pavilion dv6 model) worked very well.  It has been plugged in the power cord and adapter at the time.  One day, I went to check my emails and the laptop suddenly acted like it has been restarted, then it turns off completely.

  I waited a few minutes for re - turn on the laptop, but it does at all.  I unplugged the power cord and plugged in the power cord into the computer slot, but the led next to the power cord housing doesn't appear as it normally does when it is plugged.

  Also, when I pressed the power button to turn my phone back on, it lights.  Instead of this, a light in the front of the laptop (under the symbol of lightning bolt) flashes 3 times and then stopped flashing.  I took the battery and put it again after a few seconds, but it won't always turn.

  I noticed that the cord of the power box was nice and warm when the laptop shut down suddenly, as it was the laptop (despite the use of a laptop to refresh at the bottom of the laptop fan). The model number of the cord is WASGV0CL9YIVCU.

  What is happening with my laptop?  I use this unit to my secular Ministry work and need to work as soon as POSSIBLE!  I don't know if it's the power cord which broke or the battery needs to be replaced.  I bought the laptop in early 2010 and kept in good condition since then.  Help, please!

  Jessie

  Hey @prettykittyabc ,

  Welcome to the HP Forums!

  I understand you're Pavilion dv6 laptop does not light.

  The symptoms you have described would indicate the AC adapter or power cord no longer works. The laptop flashing lightning bolt symbol is the BIOS say you there is not enough power to turn on the laptop. If the adapter is connected, then it would be safe to say that the adapter is not power to the laptop, which would mean that the battery cannot be recharged.

  You can order online a replacement adapter, but I would say to contact the HP support by phone to order a replacement card for your laptop by phone in order to ensure the right adapter is purchased. Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click on the following link to get help from your region number: phone help around the world.

  Thank you!

• Problem with the Gateway using Vista laptop battery

  Hi all

  I've had this laptop Gateway for a year now and I have had this strange problem with it probably a good 3 months to own. Basically the little thing of battery indicator on the bottom right of the task bar will say "plugged in, not charging" while the laptop is plugged. So this is my little ghetto rig which leads me to believe that is not the battery or the charger which gives me the trouble.

  While the laptop is plugged in, and moan about there is no life left blah blah, I pop the battery and back in. Hop, I magically have full battery and be able to unplug the laptop for mobile use.

  I've read a lot online that it is a Vista problem, that I am running, and not a hardware problem. I would really like to know if this is true, because I am a student and prefer not spend the precious material fixing money when this is not the problem. As stated earlier, cell phone charges when it is plugged in, it SAID only that it does not load. When I pop the battery, it works fine until the next time that the battery is exhausted and then I plug it in and have to redo the same platform of ghetto.

  It's just a little a downside to keep popping up that darn battery in and out, and frankly, I don't think it's good for the laptop to keep doing this, even if it's worked for me for about 7-8 months now.

  Can someone please offer information about this weird issue?

  Thank you very much.

  Why my battery portable MD Gateway or Gateway MC series doesn't load at 100%?
  http://gateway-us.custhelp.com/app/answers/detail/A_ID/2624/kW/battery%20not%20charging/session/L3NpZC9UKjJBcnNsaw%3D%3D

  Also in this forum:
  Gateway Laptop: plugged in, does not support
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/6db4fe50-D318-44DA-a938-2fc58f4bbe7b
  on one of the post of Leaky.

  I hope I could help

• I have the problem with the time in my laptop

  Hello everyone,

  I have issue with the time, whenever I stop my laptop for 2-3 hours. He return to date 01/01/2006 12:00 AM

  What should I do?

  Hello

  Did your laptop more than a few years old?

  The symptom you describe occurs when the battery that powers the CMOS BIOS chip wears.

  The CMOS battery is responsible for providing voltage to the CMOS chip so that he remembers actually all parameters, including the time and date, that have been defined.

  Replacing the CMOS battery is pretty simple in a standard OEM desktop PC. Unplug the unit. Open the case locate the quarter size battery. Remove the old battery and replace it with a new one. Plug in power and start the PC and set the time and date and accept the default settings. That's about all there is to it.

  Replacing the CMOS battery in a laptop requires generally a bit of disassembly of sequential parts just to get to the battery. Not all laptops are, but most are like this.

  I recommend that you have the CMOS battery, replaced by a HP authorized repair center.

  Kind regards

  ERICO

• Huge problem with the system on my laptop Acer s7-391 acer recovery disk

  Hi all, I'm really desperate as my laptop have stopped working for the weeks and I need it back

  First question: I installed the window 10 free upgrade successfully, however, I decided to restore the laptop through the window 10 plant factory restore Start menu because there were a lot of unnecessary files and after the window factory restore, I am unable to start again under the window and I get an error message says "no bootable device detected" and the computer goes into a reboot loop no way to factory restore to new outside the window. I try to reset the battery several times and nothing works!

  Second question: I received my acer restore disk that I got from the acer site because I didn't not create recovery media to when my window was working. So I pop the disk with a usb CD-ROM and I was able to get into recovery by the disc menu. However, when I try to choose the option of disk factory restore, he said to start from legacy mode. However, when I go to legacy mode he gave me an 0xc0000017 error code saying: not enough memory to create the virtual disk. If does not work reinstall drive

  Anyway to solve the above problems, should I do it before I jump into the Acer restore with legacy mode disc? Should I send it to Acer for repair? I really need this phone in working condition.

  Thank you guys!

  A live bootable CD is probably the best option for your situation:
  http://www.partitionwizard.com/Partition-Wizard-bootable-CD.html
  Download the .iso file
  then use a software to burn CD/DVD or USB flash drive and burn the .iso file
  Once completed, put the CD/DVD/USB on your PC, boot from CD/USB (maybe you need to start under the legacy if you have the UEFI BIOS)
  Press F12 on startup and choose the CD or USB
  at the level of the Office
  Select your HARD drive
  Right-click on the icon for your HARD disk, and then choose Remove all xxxx and click Yes, and then apply
  http://www.partitionwizard.com/help/delete-all-partitions.html#HOWTO
  or wipe your HARD drive completely (it will erase any GPT or MBR at the disk), choose the first option after selecting the clear function.
  Exit the wizard partition, boot from the BIOS, UEFI return of the Legacy (if you have the UEFI BIOS) and boot from media erecovery.

• Windows 7 problem with the Dell XPS 15 laptop (L502x)

  Dear friends,

  Greetings!

  I need your assistance related to a problem, I was confronted with my Dell XPS laptop computer L502x purchased in the United Kingdom a couple of years back. In fact, I tried to update my system for windows-10 de-windows 7 Home Premium (originally installed) via windows update. Later, due to some display problems driver I had to return to the former. But, as soon as I returned my windows for windows 7 HP, it stopped at day no more and I was constantly receives the message from windows update that always ends with a constant error message; so the update process has failed every time.

  Therefore, I want to restore my laptop to factory through the restore partition settings that already exist in my machine, the "repair" option does not appear (snapshot attached) when I hit the F8 key. I wonder if there is another option available to use this recovery partition to recover my laptop to factory State. Please suggest me the solution so that I can do what is necessary to restore my machine to the factory settings.

  I can't wait to have an encouraging response from you.

  Best,

  Adnan!

  If the Ctrl key pressed, while pressing the F11 key repeatedly (about once per second) at startup does not work, it means that the recovery partition no longer exists.  If this is the case, you cannot restore to the factory.

  This would also be the case if the hard drive has been replaced.

• Have problems with the graphics card in laptop Amilo pa 1510 when you use the Windows 7 operating system

  Original title: ATI display driver my supposed UN stops and restoring it automatically when it Enmodepleinecran screen mode, why?

  When he restores it does in normal screen mode frozen, exit full screen running in background.

  What can be done to prevent this. I updated the driver software, but it had no effect

  So, what is the make and model PC?

• Problems with the speed of execution on my T420

  I'm not very tech savvy, so bear with me please if I have forgotten something or doing something wrong.

  Just to clarify, my laptop is a Lenovo ThinkPad T420i, Type 4178. It is about 2 years old.

  I have Windows 7 64 bit.

  My laptop takes about 2-5 minutes to turn on, sometimes it turn on at all. The screen freezes every 15 seconds, but I'm still able to move my cursor. He accused some too. For example, type 'how to download google chrome' will take me sometimes a whole minute, because the only parts of the sentence will be displayed on the screen at once. My keyboard responds very well. The problem is not with wireless internet, because even if the wireless is off the laptop computer is still incredibly slow. It is impossible to watch videos because the screen freezes so.

  I had this problem with the speed of my laptop for about 2 months now. I had finished it wiping back to factory settings, downloaded every scanner malware and virus known to man (none of them found no problems with it) and updated all my drivers.

  I don't really know how to do much on my laptop other than the use of the internet. I would really appriciate instructions step by step.

  Thank you.

  Hello. I did it all at once (up to 8 GB, SSD of RAM HARD disk and reinstall Windows), that's why I can't answer you, how did each of them, but after all, my absolutely BRILLIANT T420 representation!
  Chip graphic is now the weak link, and, unfortunately, it cannot be replaced.

• I have a problem with the resolution of Photoshop 6.

  I have a problem with the resolution on my laptop my laptop Lenove userface has a resolution of 3200 x 1800, my 2560 external monitor x 1440, and on two monitors of the user, the interface is so low that I can't read anything. What I am doing wrong.

  On my screen, that the same thing is happening with Bridge and Lightroom, on my laptop, these 2 programs are ok. I use on my Lenovo Windows 8, on my second laptop, I am running Windows 7 and here, I have no problems. I would really appreciate the help.

  There is nothing to do. CS6 does not support displays high-resolution.

  Mylenium

• Problem with the HP Pavilion e033tx-15 Notebook shutdown/restart/sleep

  I had windows 8 OS 64-bit working fine with my HP Pavilion Notebook 15-e033tx.

  I had problems, so I decided to update my drivers. I already had BIOS VersionF.08 and the hp support page has shown that there is an update of the bios to VersionF.21.

  After updating the bios the problem started when I stop lighting and the laptop into sleep mode kindof. I have to hold the switch down to foce him close. If I restart it, it says "reboot pc", goes blank and then all power off, and it's not stopped.  and if I SLEEP, he's not waking up.

  I rolled back the bios and it fixed the issue.

  Then I freshly installed win pro 8.1, and it has only VersionF.21 of the bios available.  Same problem again.

  HP Support Assistant showed that a new bios update Insyde F.22. But the problem is still there.

  I searched other posts with similar problem and I can't seem to solve this problem. Help, please.

  Henrico Hello and welcome on the HP Forum!

  I understand that you have a problem with the BIOS.  I'll try my best to help you solve this problem. I suggest following the procedure described in this document for the restoration of the BIOS .

  If this does not resolve this problem then restores the version F.08 http://support.hp.com/us-en/document/c02693833 driver it should always work for Windows 8.1.  Here is a document for more information of the device to Windows 8 Manager which explains how to roll back the driver. It will be the same steps for Windows 8.1.

  I suggest Using HP Support Assistant (Windows 8) to change your settings for manual update. This allows you to choose what you want updates.

  I hope that this information help, please let me know how it goes.

  Thank you and have a great day!

• HP 15 laptop: problem with the touchpad and the key "stuck."

  Hello!
   
  Last weekend, I have an irritating problem with my HP 15 laptop. Bought two years ago and upgrades to Windows 10 a year ago.
   
  First of all, my touchpad started to not work properly. It "freezes" and I can't use it until I click the ESC key, but it doesn't last and "freezes" again a few seconds later. Then, everytime I open a window where there is a text box (Start menu, edge browser, Control Panel, etc.), the number 5 is entered automatically and permanently, as if the button 5 has been blocked. I did a quick check and button 5 do not seem physically stuck.
   
  Yesterday, I restored the system to the factory settings, so I'm back to 8.1 for Windows and then upgraded to Windows 10. Everything seems to work fine, but this morning, the problem was back. Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.
   
  Thank you in advance for your help!

  Welcome to the HP support community @gouch3.

  I understand that you have a problem with the keyboard and the touchpad on your laptop from HP 15.

  Have you tried to use a keyboard external and mouse at all?

  Have you tried to go to Safe Mode to see if the problems persist in there?

  Have you tried to perform a material or forced reset Reset?

  Did you do a test of material?

  Have you updated your drivers?

  gouch3 wrote:

  ... Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.

  It could be a driver problem to be able to look at that for you, I need your model number. I wish I could give you an answer or not, but at this point without the troubleshooting results and the model number, it is difficult for me to say.

  I can say that if everything works in point 8.1 of Windows without problem, the driver TROUBLESHOOTING is a great place to start. Please try to follow these steps for the keyboard and the touchpad of troubleshooting:

  • Beginning
  • Search for Device Manager
  • Search results, open Device Manager.
  • Click on display
  • Show hidden devices.
  • Click the arrow next to keyboards.
  • Right click on the name of the keyboard device.
  • Select uninstall.
  • Continue deleting the names of devices in the category keyboards until the feature of all the names have been uninstalled.
  • Restart the laptop twice.

  Touchpad:

  • Type of research, "Device Manager."
  • Click on Device Manager,
  • Expand mice and other pointing devices.
  • Right click on the TouchPad,
  • Click on uninstall.
  • Restart the computer laptop twice,
  • Reinstall the TouchPad card.

  I found a document of troubleshooting for you to try also called Portable keyboard troubleshooting. Please be sure to follow the steps described in this document.

  The best document I have for TouchPad problems is the use and troubleshooting of the TouchPad and ClickPad document. 

  Here is a link to the HP Support Assistant, if you need it. Just download and run the application and it will help with the software and drivers that need to put up-to-date.

  This is a great question other clients may also be questioned. When we came to a resolution, please share what has worked for you with others by marking this post as an acceptable Solution. If you want to show appreciation for my efforts today, please take a second to click the Thumbs Up button below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems. Could you please also provide your model number (How can I find my model number or product number?)

  Thank you!

• HP pavilion dv6-2150us: problems with the upgrade of processor for an i7-720qm on a hp pavilion dv6-2150us

  Hi all

  My friend recently bought an i7-720qm processor used to upgrade hp pavilion dv6 2 1 5 0 US and I

  summer giving a helping hand by making the upgrade.

  Since the 10 Windows running Google Chrome used up to 70% of the processing of an i3 - 330 m power

  processor, it seemed to be good upgrade to improve the performance of the laptop.

  We checked that the new i7 processor is compatible with the laptop (it is listed as supported by the)

  ( interview guide , page 108), and the seller assured us he tested the CPU on some different

  HP pavilion and it worked fine.

  But when I replaced the processor with the i7 processor i3 and tried to boot up the laptop, only the LED lights

  on the front and the setting of the power and volume buttons would light up periodically. The screen was black

  All the time.

  Thinking I might have made a mistake during the reassembly of the laptop I put the original i3 processor back in

  and it starts fine.

  I updated the BIOS of the F.1C version I found on the internet and once replaced the i3 with the i7 with the

  same results - display off, flashes periodically LEDs. The BIOS updated smoothly, and the correct version is displayed in the main menu of the BIOS.

  I am confused on what could be the problem with the upgrade, everything should work. Is there a BIOS update I have

  missed, or the problem elsewhere?

  Disassembly and reassembly are made with care, and we took care to avoid static electricity. All the rest

  on the laptop works well - I am writing this post on the laptop in question with the original i3 processor in place.

  Any help, advice or general guidelines as to what should be done would be really appreciated.

  Thank you for your attention.

  Hello:

  The problem is that if you look in Chapter 3 of the manual, pp 22-23, there are maps of separate used for the dual core and quad core processors system.

  In other words, you cannot install a quad core processor in a Board that originally had a dual core processor and vice versa.

• Pavilion 15-e070sl: problem with the key "cancelled."

  Hi guys,.

  I have some problems with the key "cancelled." It does not work for a few months. But the more serious problem is that sometimes when I double click on a file or a folder with my mouse compares the window cancellation asking me to confirm moving the file to the trash. This window disappears until I have restart the system. He thus annoyng. It seems that the key 'cancelled' suddenly to work again when I double click on something.

  I hope you find a solution

  With the availability!

  Hi @MichaelMazz ,

  Thank you for visiting the Forums HP's Support and welcome. I looked in your question about your HP Pavilion Notebook 15-e070sl and the keys does not properly.  Select an on-screen keyboard layout using this document , as this could be the problem.

  If this is not enough, try this document on troubleshooting the keyboard. You can watch the laptop marked key stuck section.

  Here is a link to uninstall the keyboard. Restart the computer after the uninstall, it must be reinstalled automatically.

  Have you tried to clean the key or use air to blow the key there could be debris in the key itself?

  I hope this helps.

  Thank you.

• problem with the drivers for the card microsoft virtual wifi miniport... problems with PnP devices

  He said to reinstall the drivers for this problem, but they don't reinstall... also he says hardware changes have been detected... can someone explain in easy to understand words what the problem is and how to fix it... pleaseeeeee... Thank you... The convenience store said: THERE IS A PROBLEM WITH THE DRIVER of MICROSOFT VIRTUAL WIFI MINIPORT ADAPTER... DRIVERS MUST BE REINSTALLED... it won't reinstall... also: PROBLEM WITH PnP DEVICES HARDWARE CHANGES HAVE BEEN DETECTED? CAN SOMEONE HELP ME UNDERSTAND, IN EASY WORDS, EXACTLY WHAT I NEED TO DO TO FIX THIS... CD-ROM... IM USING A SAMSUNG LAPTOP MODEL NPR 519 RUNNING WINDOWS 7... Thank you... Update on the microsoft Web site says: this DEVICE no IS NOT WORKING PROPERLY BECAUSE WINDOWS cannot LOAD THE DRIVERS REQUIRED for THIS DEVICE (code 31)... im not computer savvy please someone help

  Hi MAGIC,

  It seems that you may need to update your BIOS firmware.

  You may need to contact Samsung for more information, if the update is available for download on their Web site.

  When started this issue is happening?

  You can disable the virtual WiFi adapter, as it essentially works as a tool of development at the moment:

  http://msdn.Microsoft.com/en-us/library/dd815243%28VS.85%29.aspx

  What is the device that has the problem?

  Reinstall the drivers to fix the problem?

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.