Similar Questions

• Problem with fs_clone adoption after upgrade to R12.2.3 on the instance of SCREWS

  I installed instance EBS R12.2.0 Vision on Oracle Linux Server version 6.5 x 86-64 with Unbreakable Enterprise Kernel Module 3 (3.8.13 - 16.2.2.el6uek.x86_64) and then updated to R12.2.3.  Everything went smoothly with the initial installation, the AD and T2K patches and the adoption patch cycle to 12.2.3 update.  I'm having a problem with the fs_clone running, which is the first step of the subsequent update of doc 1586214.1.  The other phases of the adoption ran OK see below.  Also here is the error I get and you want to know if anyone has experienced this or ideas?  I searched google and MOS but couldn't find a direct hit.  I'm new to adoption and struggling to solve it... any help would be appreciated. I ran to the stage of fs_clone once or twice but I got the same result.

  adoption-status-detail (it is the cycle of update R12.2.3).  Every step seems OK here.

  Current patch ID of Session: 4

  Name of node node Type Phase status started completed elapsed
  --------------- --------------- ----------- --------------- ------------------------------ ------------------------------ ------------
  HN-s-sb13 master PREPARE ENDED December 27, 13 09:27:31 - 05:00 27 December 13 09:55:35 - 05:00 0:28:04
  APPLY FULL 27 DECEMBER 13 10:11:53 - 05:00 27 DECEMBER 13 09:35:53 - 05:00 11:24
  FINALIZE ENDED 28 DECEMBER 13 09:28:46 - 05:00 DECEMBER 28, 13 09:29:52 - 05:00 0:01:06
  FAILOVER COMPLETED 28 DECEMBER 13 09:32:12 - 05:00 28 DECEMBER 13 10:05:35 - 05:00 0:33:23
  CLEANING ENDED 28 DECEMBER 13 10:25:22 - 05:00 28 DECEMBER 13 10:48:31 - 05:00 0:09:23

  
  Folder synchronization system used in this Patching Cycle: None
  Generate full ADOPTION status report to the location: /u01/oracle/VIS/fs_ne/EBSapps/log/status_20131229_120910/adzdshowstatus.out
  Please wait...
  Done...!

  adopted out with status = 0 (success)

  From txkADOPPreparePhaseSynchronize_Sat_Dec_28_12_40_05_2013.log:

  ---------------------------------------------------------------------------------------------

  ==========================
  SetCloneStatus() inside...
  ==========================

  Generation SQL file: /u01/oracle/VIS/fs_ne/EBSapps/log/adop/5/fs_clone_20131228_123623/VIS_hn-s-sb13/TXK_SYNC_create_Sat_Dec_28_12_40_05_2013/5_DEREGISTER-ORACLE-HOMES.sql
  SQL command: UPDATE ad_adop_session_patches SET clone_status = "cancel the REGISTRATION-ORACLE-HOMES ' WHERE State = ' no AND numero_de_bogue = 'CLONE' AND node_name = 'hn-s-sb13' AND adop_ses
  sion_id = 5;
  Run the SYSTEM command: sqlplus * @/ u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20131228_123623/VIS_hn-s-sb13/TXK_SYNC_create_Sat_Dec_28_12_40_05_2013/5_DEREGI
  STER-ORACLE - HOMES.sql
  EXIT STATUS: 1
  SQL execution went through successfully.
  LOG FILE: / U01/ORACLE/SCREWS/FS_NE/EBSAPPS/LOG/ADOPTION/5/FS_CLONE_20131228_123623/VIS_HN-S-SB13/TXK_SYNC_CREATE_SAT_DEC_28_12_40_05_2013/5_DEREGISTER-ORACLE-HOMES. OUT.
  FATAL ERROR *.
  PROGRAM: (/ u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOPPreparePhaseSynchronize.pl)
  TIME: Sat Dec 28 12:42:54 2013
  FUNCTION: main::runFSCloneApply [level 1]
  ERRORMSG: /u01/oracle/VIS/fs2/EBSapps/comn/clone/bin/adclone.pl does not pass successfully.

  From adop_20131228_123623.log:

  -----------------------------------------------

  ADOPTION Session ID: 5
  Phase: fs_clone
  [BEGINNING 2013/12/28 12:39:57] fs_clone phase
  [EVENT]     [BEGINNING 2013/12/28 12:40:01] Clone BY following the steps
  [EVENT]     [BEGINNING 2013/12/28 12:40:02] Patch CLONE of the file system to perform file system
  [EVENT]     The call: /u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOPPreparePhaseSynchronize.pl
  [STATEMENT] Output directory: / u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20131228_123623/VIS_hn-s-sb13
  [UNEXPECTED] Error occurred during execution of < perl /u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOPPreparePhaseSynchronize.pl - contextfile = / u01/oracl
  e/VIS/fs2/inst/apps/VIS_hn-s-sb13/appl/admin/VIS_hn-s-sb13.xml-patchcontextfile=/u01/oracle/VIS/fs1/inst/apps/VIS_hn-s-sb13/appl/admin/VIS_hn-s-sb13.xml - promptmsg = hide - co
  mark = off - mode = create - sessionid = 5 - timestamp = 20131228_123623 - outdir = / u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20131228_123623/VIS_hn-s-sb13 >
  [UNEXPECTED] Error occurred while CLONE Patch File System to run file system using the command: perl /u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOP
  PreparePhaseSynchronize.pl-contextfile=/u01/oracle/VIS/fs2/inst/apps/VIS_hn-s-sb13/appl/admin/VIS_hn-s-sb13.xml - patchcontextfile = / u01/oracle/SCREWS/fs1/inst/apps/VIS_hn-s-sb1
  3/appl/Admin/VIS_hn-s-SB13.XML - promptmsg = hide - console = off - mode = create - sessionid = 5 - timestamp = 20131228_123623 - outdir = / u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20
  131228_123623/VIS_hn-s-sb13 >.
  [PROCEDURE] [BEGINNING 2013/12/28 12:42:55] Check and stop Patch Server Admin
  [STATEMENT] select count (1) of ad_adop_session_patches
  where applied_file_system_base = ' / u01/oracle/SCREWS/fs2 ' and
  patch_file_system_base = ' / u01/oracle/SCREWS/fs1 "and
  numero_de_bogue IN ('CLONE', 'CONFIG_CLONE') and
  status (', 'F')

  [STATEMENT] There is a clone session waiting for/u01/oracle/SCREWS/fs1.
  [STATEMENT] Jumping to check and stop the Patch Server Admin step.
  [PROCEDURE] [END 2013/12/28 12:43:01] Check and stop Patch Server Admin
  [UNEXPECTED] fs_clone phase completed with errors/warnings. Check the log files
  [PROCEDURE] [BEGINNING 2013/12/28 12:43:03] Unlock sessions table
  [STATEMENT] SQL stmt: start
  AD_ZD_ADOP. UNLOCK_SESSIONS_TABLE('hn-s-sb13',60,2);
  end;
  >

  [PROCEDURE] [END 2013/12/28 12:43:07] Unlock sessions table
  Log file: /u01/oracle/VIS/fs_ne/EBSapps/log/adop/5/adop_20131228_123623.log

  Randy,

  Looks like you need to add more space to the directory/tmp, I see the following entries in the CLONE*.error file.

  CLONE2013-12-28_12-41-01 PM .error:

  =================================

  SEVERE: 28 December 2013 12:42:46 - ERROR - CLONE-20275 not enough space to create/tmp/CLONINGCLIENT8522798570339051663.

  SEVERE: 28 December 2013 12:42:46 - CAUSE - CLONE-20275 minimum required space was at '1 798' Mo, but only '1 737' MB was available for use.

  SEVERE: December 28, 2013 12:42:46 - ACTION - CLONE-20275, make sure that the minimum required space is available for use.

  GRAVE: 28 December 2013 12:42:46 - ERROR - CLONE-20233 restoration Middleware House for sourceid 'mwhome1@FMW_Home' failed.

  GRAVE: 28 December 2013 12:42:46 - CAUSE - CLONE-20233 an internal operation failed.

  Thank you

  Hussein

• Problem with desktop/taskbar after upgrading Fusion 4 to 6 - Windows 7 VM

  I got a few problems after upgrading to Fusion 4 to 6 with my Win 7 x 64 bit VM Fusion. I use a Mac Pro with the Mavericks. While I managed to resolve most of the issues with a manual installation of the VMWare Tools and reconstruction/reactivate a certain number of broken programs, there is suddenly a new which is serious enough. My office is not displayed, nor is my bar of the shortcut icons for the launch of the program tasks. I can access my desktop to the user manually folder and all the "stuff" is there. " If I run a program from the icon appears in the taskbar, but it cannot be pinned. When I access more nothing, I get this popup (see image). I'm sure that's the issue. Anyond can suggest a solution, please?

  Hello

  The network error is gone I hope?

  You have to set up folders mirrored under sharing with OS X? (Menu-> Virtual Machine-> settings-> sharing-> mirrored folders). If you use mirrored folders there, then what happens if you turn off this feature to test and see?

  I don't use this feature myself, but imagine that allowing a case mirrored for Office could eventually hide something on the side of windows.

  --

  Wil

• Anyone having problems with WiFi connectivity after upgrade to Sierra?

  I was wondering if anyone else knows issues with WiFi connectivity since the upgrade to Sierra 10.12? I have not had any problems with connectivity WiFi previously on El Capitan. Now I have regular randomly loose connectivity. My internet is cable and when it is connected I have a 100% connection. My details of iMac and I have used only 10% of my storage.

  

  No problem with my iphone 6.

  Hello AspDesigns,

  I understand that, since the upgrade to Mac OS Sierra, your Mac seems to have trouble staying connected to Wi - Fi. Fortunately the diagnosis built-in wireless can help identify the source of so much trouble.

  Search for Wi - Fi using your Mac problems

  See you soon!

• TouchSmart HP ENVY 15-j040us Notebook PC-problem with internet gambling after upgrade to 8.1 windows

  I have a HP Envy 15-j040us Notebook PC Touchsmart is currently using 8.1 64-bit windows.  I play 2 Farmville on Facebook.  I started having problems after installing Windows 8.1.  My mouse hesitates and reluctant game and I can barely move on the screen.  I am not real computer savy but can follow directions if you can just tell me what I need to do to correct this.  Everything on the screen is just very slow and the mouse does not seem to want to go where I'm pointing to it.

  Hello @aodom ,

  Welcome to the HP Forums!

  I see that you have any questions, play Farmville 2 since the update to Windows 8.1.

  First, update the drivers for your graphics (GPU) with the following download: driver Intel graphics high definition (HD).

  Once you have done this, update Adobe Flash player plugin with the following download: Adobe - Flash Player

  Once you have updated the GPU and the Flash Player, disable hardware acceleration for Flash on your laptop:

  1. Right click any where on the Farmville game once it has loaded.
  2. Select settings.
  3. Make sure that you are on the tab display/graph (see image below).
  4. Clear the check box to enable hardware acceleration if it is available. If you are prompted to activate the control of your webcam or microphone that these steps do not apply because the game is not trying to use the acceleration.

  

  Let me know if it helps.

• Problem with PCI-6704 after upgrade

  I recently upgraded from labview 7.1 to 8.6, at the same time I've upgraded to the latest version of the driver NOR-DAQmx, MAX and the existing drivers (7.4.4). After upgrading my PCI-6704 Board has stopped working. When I try to run the test panels I get a message "the device is not the test. Do you want to continue? "If I click on Yes, the test Panel opens and I get the message error in 10461. I tried to reinstall both daqmx drivers existing. I tried to uninstall both drivers and remove cards, restarting the computer, and then reinstall the new. I tried to install only the existing drivers and I get the same error. The pilots reset has no effect. I also tried switching PCI slots. I have a card PCI-MIO-16-1 and it works very well, and it works in a pci slot. Is there anything else I can try?

  I uninstalled the NOR-DAQ traditional 7.4.4 and installed instead of NOR-traditional DAQ 7.1 and everything works well again. Apparently there is something in the 7.4.4 update that did not like the PCI-6704.

• Problems with mail imap after upgrade of Sierra

  After the upgrade to Sierra, I can't sync my hotmail account in Mail.

  Before even the upgrade, I always had to change my account after each restart settings, as required for authentication SMTP and IMAP user name has been deleted. The same thing happens after the upgrade, but now when I enter the user name and press save I have error message say: A IMAP account already exists.  Only one IMAP account is allowed to be saved.

  Reming the account and recreate it does not help because I find myself in the same situation where the username is missing. Does anyone have any suggestions?

  

  The username field must my work email address and when I enter it and press on save, the error message comes.

  I am facing a problem as well with Mail on macOS Sierra: account sync not IMAP.

  I see that there are a lot of similar questions autour... hope they will fix soon!

  Even that when troubleshooting your...

• Problem with Microsoft Office, after upgrade Windows 8.1

  Simple and straight to the point.  After the upgrade to Windows 8.1 my Office Home and Student 2010 will only work for 15 minutes after the installation, and then after that the logo for Word or Excel screen rises, opens ever, not useful to insert the disc, the execution of repairs, which reuqires reboot of the system, whenever I need to use Word or Excel.  Someone please tell me there is a simple solution for this problem.

  Victorymarketin, welcome to the forum.

  Since they are two Microsoft programs, I suggest to contact MS Service customer assistance.  They always took me and running in short order.  It's always my solution when I have MS related problems.  They if anyone can solve your problem.

  If your problem is solved, please click "accept as a Solution.

• Problems with global.licenses after upgrading to 5.5

  Just updated to 5.5 and started using the web client instead of the old local customer... Time to learn new things...

  Well, after the upgrade, I am not able to manage some things, open console a virtual machine or access the different tabs etc..

  I get this error (under Administration licenses - licenses)

  The Global.Licenses privilege is required on the server vCenter selected system. Give a Global.Licenses on the selected vCenter Server system to see the licensing information

  No idea what to do, tried to look on the web and look round in the web client, but nothing. !

  Found the solution here.

  vCenter Server error you do not have a permission. When you try to connect to vcenter server 5.5 via Customer Center v

  For some reason anyone else the local administrator had permission on the object of data center.

  Administrator local and added our Domain Admins group with administrator permissions and voila!

• Problem with server HQ after upgrade

  Just going through the process of upgradeing our current working installation.
  
  We have server HQ upgrades of version 3.1.4 who was running successfully under windows 2003 server by using the postgre database integrated in version 4.1.0 on the same server.
  
  The upgrade process seems to happen unhindered. Then we have configured the option "Run as service" went to windows services and the service started.
  
  We waited 2 hours and whenever we try to connect to the site we get the message.
  
  The HQ server is always from.  The database is a bit more than 5 GB in size.
  
  Should expect us start to have finished now?
  
  Is there something in particular, that I must look in the newspapers?
  
  I noticed that there was a previous post with a link to the ports required for HQserver.
  I have checked and I can say none of the ports are used by other programs.  Firewall Windows is not lit on this machine.
  
  concerning
  
  Spencer

  It is indeed a redundant index, don't know why it is added here.  Search for db - upgrade.xml in the installer and modify it.  Find the following section:

  
     
  precision = columnType "512" = "VARCHAR2" / >

  
       
  targetDB 'postgresql' = >
  CREATE INDEX cresp_err_idx ON EAM_CONFIG_RESPONSE USING btree (validationerr)
       
     
   

  Remove the creation of the index:

  
       
  targetDB 'postgresql' = >
  CREATE INDEX cresp_err_idx ON EAM_CONFIG_RESPONSE USING btree (validationerr)
       
     

  Restart your upgrade.  He will have to investigate why it was put there in the first place.

  Charles

• Problems with PCI-7811R after upgrade from LabVIEW

  Hello

  I have been using a PCI-7811R under LabVIEW 8.2 for quite awhile without difficulties. However, I just upgraded to LabVIEW 2009 and it seems to have stopped working.

  I tried to run old code (that worked before) and I get the attached error. I try and locate the PCI-7811R in MAX ver 4.7.7 and he's not here.

  Any suggestions?

  Gary

  
  

• Problem with the touchpad after upgrade to Windows Vista

  After that I've upgraded to windows vista I had problem with the touchpad, that I'm not?

  Can U help me!

  Maybe when you tell us what model of laptop you have. ;)

• Problems with the touch screen of HP all-in-One after upgrading Windows

  I recently updated my version of Windows (64-bit) with system updates and then a full version updated to version 8.0 version 8.1.  After the update is complete, I started to experience a strange problem with the touch screen on my HP Envy Rove.  The screen would flash repeatedly one set of points in the right lower quadrant of the screen as if the simulation random screen button.  There is no way to stop this.  If the screen on a keyboard was pulled up, letters in the place of the flashes would be broadcast in the fields on the screen.

  The only way to stop the flashes of screen has been to go into the Device Manager and disable the HID-Compliant device driver.  It stopped (system generated keys) flashes, but also disabled my touch screen input.  So now the system is usable, but without the benefit of the touchscreen.

  Here is the information on the driver:

  HID-Compliant device

  Date: 21/06/2006

  Version: 6.2.9200.16851

  (input.inf)

  I tried updating the driver, but this seems to be the latest version available.  Go back to the previous version of the driver, could solve the problem, but I could not locate on the support web site.

  Any suggestions on how to solve this problem and re-enable the ability of my touch screen?

  Hello

  Downloaded drivers from the manufacturer will be the most tested and up to date available. The best place to download a driver is directly from the manufacturer of the equipment.

  So I suggest you to install the driver that is available on the HP website for your model.

  Troubleshooting of touch screen in Windows 8

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&DLC=en&docName=c03488148

  Just reply with the results.

• I can not install Lightroom 6 after a problem with the pc and upgrade to Windows 10. "Errors occurred on your installation.

  Hello

  I am a user of Lightroom 4 since it came out and it worked fine.

  My system is based on a motherboard Asus Maximus III, the Intel Core i7 875K 2.93 GHz processor, card EVGA Geforce GTX 960 Graphics, Corsair Vengeance 8 GB of RAM.

  I used to have Windows 7 Home Eng 64 bit on it.

  After installing Lightroom 6 everything is fine again, but then the evil came:

  There was a problem with the pc, so I had to use the restore before installing Lightroom 6 point, bringing back me to Lightroom 4

  The problem is that somehow my internetbrowsers stopped working one by one. A virus? Norton was running, so it shouldn't.

  The restoration of an early version did not help the problem

  I needed the PC for work so I installed the free update for Windows 10

  Now, I can not install my Lightroom 6 more: it keeps giving me the following box:

  

  Of course stop the firewall did not help. Looks like a standard sentence as well.

  How to solve this?

  Thank you for reading.

  Settle in the right forum.

• Problem with the Conexant HDAudio after installing x 86 Vista SP1

  I didn't want to start a new thread, but it seems that my problem is quite unique.
  
  When the first x 86 Vista install my speakers/headphones worked great. After Vista SP1 installed, my speakers/headphones went silent, but the pilot was still there and working properly. I uninstalled the driver and let Windows automatically install a different driver. (No Rollback was available) I could get the sound from my speakers. Speakers are the only thing that works if I plug into the headphone jack or not.

  When connected to the plug headphones I have test the headphones feature in playback devices and receive nothing in the helmet.
  
  Drivers of HP support only cut my speakers while doing my reading helmet camera disappear. Even with the updated driver.
  
  I like to use it as a TV computer and would like the sound of the TV via the headphone jack.
  
  I searched EVERYWHERE on the internet and found no resolution. Any help would be appreciated.
  
  HP pavilion dv6748us

  Conexant Audio
  
  Hardware ID:

  HDAUDIO\FUNC_01 & VEN_14F1 & DEV_5051 & SUBSYS_103C30CF & REV_1000

  HDAUDIO\FUNC_01 & VEN_14F1 & DEV_5051 & SUBSYS_103C30CF

  Have encountered problems with the card drivers its me on vista & 7 even when driver installation correct support downloaded installers.

  Only solution I found was to download a range of versions of different driver bought research google & trials, tedious but sometimes only way to get the result.

  If you uninstall the driver & restart it installs a generic driver audio Conexant or Windows!

  I also use my laptop with TV & hifi so work taken audio is a must (card input jack usb audio can be an option if)

  Also never rule out the fault of Council helmet as have a Pavilion & after that OS installed on a new drive HARD had no audio for headphones, pilot presumed linked, but after fiddling fuond twist got jack sound, turned Ribbon glued on card Board failed.