Similar Questions

• Problem with VPN compatibility between 2811 and 2911

  Hello

  I would ask anyone had problems with the implementation of a VPN tunnel between 2811 and 2911?

  The IPSec VPN is established, but for some reason, I cannot ping the side LAN across LAN to the other end of the VPN router?

  All experience would be highly appreciated

  Thank you

  IPSec VPN can be smoothly between routers cisco (and not nesesserely cisco) set up, so there should be no problem in your case.

  If you say that this tunnel is established successfully, then the problem most likely related to routing problems between sites or incorrect configured crypto-acl. Check if the hosts located on both sites have correct routing information on how to get to subnets on the other site.

  Make more accurate assumptions, it would be helpful that you provide config on both sites and describe your topology.

• I have a problem with synchronize them between (summary) video and slides in IPADs, HTML5. Please, help me!

  I have a problem with synchronize them between (summary) video and slides in IPADs, HTML5. Please, help me!

  I have an idea, I think that what's happening is the fact that the video is not charged, it cannot find the video, he goes to the last downloaded part.

• Problem with IPSEC tunnel between Cisco PIX and Cisco ASA

  Hi all!

  Have a strange problem with one of our tunnel ipsec for one of our customers, we can open the tunnel of the customers of the site, but not from our site, don't understand what's wrong, if it would be a configuration problem should can we not all up the tunnel.

  On our side as initiator:

  Jan 14 13:53:26 172.27.1.254% PIX-7-702208: ISAKMP Phase 1 Exchange started (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702210: Exchange of ISAKMP Phase 1 is complete (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% 6-PIX-602202: ISAKMP connected session (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-6-602201: Phase 1 ISAKMP Security Association created (local 1.1.1.1/500 (initiator), 2.2.2.2/500 remotely, authentication = pre-action, encryption = 3DES-CBC, hash = SHA, group = 2, life = 86400 s)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702209: ISAKMP Phase 2 Exchange started (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702201: ISAKMP Phase 1 delete received (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-6-602203: ISAKMP disconnected session (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:56 172.27.1.254% PIX-7-702303: sa_request, CBC (MSG key in English) = 1.1.1.1, dest = 2.2.2.2, src_proxy = 172.27.1.10/255.255.255.255/0/0 (type = 1), dest_proxy = 192.168.100.18/255.255.255.255/0/0 (type = 1), Protocol is ESP transform = lifedur hmac-sha-esp, esp-3des 28800 = s and 4608000 Ko, spi = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 4004

  The site of the customer like an answering machine:

  14 jan 11:58:23 172.27.1.254% PIX-7-702208: ISAKMP Phase 1 Exchange started (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-7-702210: Exchange of ISAKMP Phase 1 is complete (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% 6-PIX-602202: ISAKMP connected session (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-6-602201: Phase 1 ISAKMP Security Association created (local 1.1.1.1/500 (answering machine), distance 2.2.2.2/500, authentication = pre-action, encryption = 3DES-CBC, hash = MD5, group = 1, life = 86400 s)

  14 jan 11:58:23 172.27.1.254% PIX-7-702209: ISAKMP Phase 2 Exchange started (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-6-602301: its created, (his) sa_dest = 2.2.2.2, sa_prot = 50, sa_spi = 0x9de820bd (2649235645) sa_trans = sa_conn_id of hmac-sha-esp, esp-3des = 116

  14 jan 11:58:23 172.27.1.254% PIX-7-702211: Exchange of ISAKMP Phase 2 is complete (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  Jan 14 12:28:54 172.27.1.254% PIX-6-602302: SA deletion, (his) sa_dest = 2.2.2.2, sa_prot = 50, sa_spi = 0x9de820bd (2649235645), sa_trans = esp-3desesp-sha-hmac, sa_conn_id = 116

  Kind regards

  Johan

  From my experience when a tunnel is launched on one side, but it is not on the other hand, that the problem is with an inconsistency of the isakmp and ipsec policies, mainly as ipsec policies change sets and corresponding address with ASA platform when a tunnel is not a statically defined encryption card he sometimes use the dynamic tag to allocate this vpn connection. To check if this is the case go ahead and make a "crypto ipsec to show his" when the tunnel is active on both sides, see on the SAA if the corresponding tunnel is the static encryption card set or if it presents the dynamic encryption card.

  I advise you to go to the settings on both sides and ensure that they are both in the opposite direction.

• Problem with WISN LAP-1131 and Cisco

  Hello

  I have a Cisco WISN running the 7.0.116.0 version and it works very well with a lot of access Cisco 1131/1232/1242 points. But with one I have a problem. He has worked and loaded the flash image and got the ip address controller and began to show the below error:

  * 12:26:40.001 June 8: % CAPWAP-5-CHANGED: CAPWAP changed State to

  * 12:26:41.386 June 8: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.23.2.244 peer_port: 526

  * 12:26:41.388 June 8: % CAPWAP-5-SENDJOIN: send request to join 172.23.2.244

  * 12:26:41.388 June 8: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE

  * 12:26:41.577 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state CFG

  * 12:26:41.583 June 8: % DTLS-5-ALERT: WARNING received: close notify alert from 172.23.2.244

  * 12:26:41.583 June 8: % DTLS-5-PEER_DISCONNECT: Peer 172.23.2.244 has closed the connection.

  * 12:26:41.583 June 8: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.23.2.244:5246

  * 12:26:42.270 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY

  * 12:26:42.271 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY

  * 12:26:42.340 June 8: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively

  * 12:26:42.340 June 8: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively

  * 12:26:42.341 June 8: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to

  * 12:26:42.370 June 8: State of WLC voice_diag_test is false

  * 12:26:42.371 June 8: % LINK-3-UPDOWN: Interface Dot11Radio1, changed State to

  * 12:26:42.372 June 8: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to down

  * 12:26:42.377 June 8: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset

  * 12:26:42.398 June 8: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to

  * 12:26:53.000 June 8: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.23.2.244 peer_port: 5246

  * 12:26:53.001 June 8: % CAPWAP-5-CHANGED: CAPWAP changed State to

  * 12:26:54.389 June 8: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.23.2.244 peer_port: 526

  * 12:26:54.390 June 8: % CAPWAP-5-SENDJOIN: send request to join 172.23.2.244

  * 12:26:54.390 June 8: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE

  * 12:26:54.577 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state CFG

  * 12:26:54.584 June 8: % DTLS-5-ALERT: WARNING received: close notify alert from 172.23.2.244

  * 12:26:54.584 June 8: % DTLS-5-PEER_DISCONNECT: Peer 172.23.2.244 has closed the connection.

  * 12:26:54.584 June 8: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.23.2.244:5246

  * 12:26:54.642 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY

  * 12:26:54.642 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY

  * 12:26:54.738 June 8: State of WLC voice_diag_test is false

  * 12:27:05.000 June 8: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.23.2.244 peer_port: 5246

  * 12:27:05.001 June 8: % CAPWAP-5-CHANGED: CAPWAP changed State to

  * 12:27:06.384 June 8: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.23.2.244 peer_port: 526

  * 12:27:06.385 June 8: % CAPWAP-5-SENDJOIN: send request to join 172.23.2.244

  * 12:27:06.385 June 8: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE

  * 12:27:06.569 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state CFG

  * 12:27:06.574 June 8: % DTLS-5-ALERT: WARNING received: close notify alert from 172.23.2.244

  * 12:27:06.574 June 8: % DTLS-5-PEER_DISCONNECT: Peer 172.23.2.244 has closed the connection.

  * 12:27:06.575 June 8: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.23.2.244:5246

  * 12:27:06.635 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY

  * 12:27:06.636 June 8: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY

  * 12:27:06.704 June 8: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively

  * 12:27:06.705 June 8: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively

  * 12:27:06.706 June 8: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to

  * 12:27:06.735 June 8: State of WLC voice_diag_test is false

  * 12:27:06.735 June 8: % LINK-3-UPDOWN: Interface Dot11Radio1, changed state

  Thank you, Vincent a.

  Edit:

  When I look on the controller message logs, I see this line:

  * apfMsConnTask_0: 16:04:47.822 Jun 08: % LOG-6-Q_IND: spam_lrad.c:1517 application discovery elements in LWAPP 00:23:33:78:df:80 AP supporting CAPWAP

  Hi Vincent,.

  in this case, if the regulatory domain of the APs is different, consider that the WLC accept associations from the country set APs:

  http://www.Cisco.com/en/us/docs/wireless/controller/7.0/Configuration/Guide/c70lwap.html#wpxref84219

  You will see this in him debugs I sent you before.

  So, if you manage APs EI (ETSI, European) and - a (FCC, US) APs on the same WLC, you need to enable at least two country codes, one for each regulatory domain.

  Please also remember that the APs should be used on the countries they have been approved to in order to comply with local regulations.

  Thank you

  Federico

• Problem with DHCP broadcast between VLAN

  Hello

  I trying to solve the lab that I set up, I have a problem with broadcast between VLANS with my DHCP. I looked around the vmware community to find my answer, but I did not who is right why I post here!

  So here's my situation :

  • ESX with 2 race of VM:
    • An R2 of 2012 Windows running a DHCP server with a configured scope
      • This virtual machine is assigned to the vmnic4 with the port VLAN 100 group
    • A Windows 7, which I use as a customer
      • This virtual machine is assigned to the vmnic4 with the port VLAN 110 group
  • Switch Cisco with a simple configuration:

  interface FastEthernet0/1

  Description LINK FOR ESX

  switchport mode trunk

  switchport nonegotiate

  interface FastEthernet0/24

  Description OF LINK ROUTER

  switchport mode trunk

  • Configuration of the Cisco "router on the stick:

  interface FastEthernet0/0.100

  encapsulation dot1q 100

  10.1.1.254 IP address 255.255.255.0

  interface FastEthernet0/0,110

  encapsulation dot1q 110

  IP 10.1.2.254 255.255.255.0

  IP helper 10.1.1.0

  
  

  The resolution of the problems that I did:

  • Affecting the client static IP and that both virtual machine can ping each other
  • Moving from the client to the same VLAN as DHCP server, and the DHCP server is to give the client an IP address.
  • Sniffing the packet:
    • I can see the client DHCPDiscover
    • I can see the router with the command "debug ip dhcp server packet" package passed on the 10.1.1.0.
    • I am not able to see the packets from the router to DHCP perspective

  That's why I guess miss me something ESX configuration.

  Thanks in advance for reading this post!

  
  

  PS: I've linked a vswitch configuration screenshot
  

  I think that you have configured an incorrect address of IP support, take a look at the following line:

  IP helper 10.1.1.0

  
  

  Your DCHP server is really 10.1.1.0? I think not, since 10.1.1.0 corresponds to the ID of the network 10.1.1.0/24 network.
  

• Problems with dynamic links between Premiere Pro and After Effects

  Hello

  dynamic binding (insertion of After Effects compositions on a Premiere Pro schedule) rarely worked properly since it was introduced. Problems vary (for example "media disconnected" made plates, old versions of comps rendered).

  What's worse, is that you can never tell what will be ultimately made out of Premiere Pro. Thus, a typical professional workflow to several projects together to finish during the day and batch overnight rendering can cause a catastrophe.

  Of course, the option is to not use dynamic link. Which makes then less competitive whole adobe.

  This subject has been widely discussed for years has been a dynamic links. I'm not the only one having this problem, and the problem is far from new.

  My only question is:

  Adobe: have you ever fix dynamic links?

  I don't really understand how you focus on software development in your company. The vast majority of the features of CC is little or not useful. The most important thing in a professional environment is consistent and reliable - performance can you please focus on that?

  I'm inspired to write this post because I just arrived in my edit at 07:00 only to find that my night makes is the wrong versions. All bed very well in the body and AE, damage the final rendering off Media Encoder used an older version of one of my compositions, and that I have nothing to send to my client.

  Janne

  Title edited by Kevin Monahan.

  Management of files Adobe seems to rely on the names and the last path of known files. Body loses links Dynamics (and other files) with frightening regularity in a situation where nothing has changed in the hierarchy of files, the files.

  16, when a hard disk of 8 GB was a huge drive, Pro Tools has been littering files on several disks because, as was the creation of audio files in real time, she had to. Digidesign introduced into a system which incorporated a unique program generated number in each file. Since that day I have never had a problem with lost files or correlate. I can move them anywhere, on any system and any PT session concludes that they are with total reliability - and we are talking about a lot of projects with thousands of files, through several studios. If you are looking for files, you can choose to use the identification number, the name of the file, the length of the file, or any combination of these. Which allows for the substitution of file.

  Until Adobe address this problem with a solution similar to that of Pro Tools, we'll be constantly beset by problems.

• Font problem with the publication between Animate and HTML?

  Hello!

  I have a problem with the publication of my animated movie in CC to animate. Some computers don't recognize the font on Google Chrome that I chose in my animation. Firefox never recognize.

  I don't know how to fix.

  Some pictures of the problem:

  -This is the image of Google Chrome with melting Source without Pro. It works normally (on some computers).

  

  -This is on Firefox. The police has not been integrated.

  

  What is going on?

  Thank you!!

  Hello

  You can try to use the type of static text in HTML5 Canvas document for WYSIWYG experience and see if that helps?

  PS: The static text in the document of the canvas is converted to outlines when publishing to preserve the WYSIWYG experience. If you have a requirement that you need to preserve the text in the js to output file, then use a dynamic text with Typekit web font for experience of consistency.

  Thank you!

  Mohan

• Problem with IPsec VPN between ASA and router Cisco - ping is not response

  Hello

  I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):

  my network topology data:

  LAN 1 connect ASA - 1 (inside the LAN)

  PC - 10.0.1.3 255.255.255.0 10.0.1.1

  ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0

  -----------------------------------------------------------------

  ASA - 1 Connect (LAN outide) R1

  ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252

  R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252

  ---------------------------------------------------------------------

  R1 R2 to connect

  R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252

  R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252

  R2 for lan connection 2

  --------------------------------------------------------------------

  R2 to connect LAN2

  R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0

  PC - 10.0.2.3 255.255.255.0 10.0.2.1

  ASA configuration:

  1 GigabitEthernet interface
  nameif inside
  security-level 100
  IP 10.0.1.1 255.255.255.0
  no downtime
  interface GigabitEthernet 0
  nameif outside
  security-level 0
  IP 172.30.1.2 255.255.255.252
  no downtime
  Route outside 0.0.0.0 0.0.0.0 172.30.1.1

  ------------------------------------------------------------

  access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
  object obj LAN
  subnet 10.0.1.0 255.255.255.0
  object obj remote network
  10.0.2.0 subnet 255.255.255.0
  NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static

  -----------------------------------------------------------
  IKEv1 crypto policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 3600
  Crypto ikev1 allow outside
  crypto isakmp identity address

  ------------------------------------------------------------
  tunnel-group 172.30.2.2 type ipsec-l2l
  tunnel-group 172.30.2.2 ipsec-attributes
  IKEv1 pre-shared-key cisco123
  Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1

  -------------------------------------------------------------
  card crypto ASA1VPN 10 is the LAN1 to LAN2 address
  card crypto ASA1VPN 10 set peer 172.30.2.2
  card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
  card crypto ASA1VPN set 10 security-association life seconds 3600
  ASA1VPN interface card crypto outside

  R2 configuration:

  interface fastEthernet 0/0
  IP 10.0.2.1 255.255.255.0
  no downtime
  interface fastEthernet 0/1
  IP 172.30.2.2 255.255.255.252
  no downtime

  -----------------------------------------------------

  router RIP
  version 2
  Network 10.0.2.0
  network 172.30.2.0

  ------------------------------------------------------
  access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
  access-list 102 permit esp 172.30.1.2 host 172.30.2.2
  access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
  interface fastEthernet 0/1
  IP access-group 102 to

  ------------------------------------------------------
  crypto ISAKMP policy 110
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 42300

  ------------------------------------------------------
  ISAKMP crypto key cisco123 address 172.30.1.2

  -----------------------------------------------------
  Crypto ipsec transform-set esp - aes 128 R2TS

  ------------------------------------------------------

  access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255

  ------------------------------------------------------

  R2VPN 10 ipsec-isakmp crypto map
  match address 101
  defined by peer 172.30.1.2
  PFS Group1 Set
  R2TS transformation game
  86400 seconds, life of security association set
  interface fastEthernet 0/1
  card crypto R2VPN

  I don't know what the problem

  Thank you

  If the RIP is not absolutely necessary for you, try adding the default route to R2:

  IP route 0.0.0.0 0.0.0.0 172.16.2.1

  If you want to use RIP much, add permissions ACL 102:

  access-list 102 permit udp any any eq 520

• Problem with routing/circuits between SG300-10 and Dell Powerconnect 5224

  Hello

  I just bought a SG300-10 switch and loaded new firmware 1.27 on it.  Configure my VLAN and trunks, but I have a weird problem that I can't seem to understand.  It may be something small, I'm missing, but no matter, I have been scratching at it all day and I kicked in the butt.  If anyone can point me in the right direction or maybe something that someone see in my config which is wrong, I can get the terminology/theory wrong, after all, I just spent my CCNA :)

  My configuration:

  I have the SG300-10 as my switch and changed over to L3, so it may be my core of my small network.  On port 1, vlan 200 is configured as my unidentified native PVID and I put it to 210(LAN network) to trunk VLANs, 220 (management vlan) on the tag to the Dell powerconnect 5224 24port switch.  On port 1 of the Dell switch, I install as a trunk it as well with the same configuration (vlan native of PVID unidentified 200, 210 and 220 tag trunking).

  I have installed virtual interfaces on the SG300 for each VLAN (vlan 210 = 192.168.210.1/24, vlan 220 = 192.168.220.1/24) and on the Dell, since this is a feature of L2, I changed the vlan 1 to 220 management and assign the IP 192.168.220.2/24.

  Now, since the SG300 web interface, I ping IP management Dell (192.168.220.2/24)successfully and vice versa, can ping from Dell web interface to one of the IP of the bridge VLAN (210.1 & 220.1) successfully so that test, to me, looks like the Dell communicates with the SG300.)  I also have the default gateway of the Dell 192.168.220.1 printer value.

  Server IP: 192.168.220.10/24

  Workstation IP: 192.168.210.80/24

  Now the dilemma:

  I have a server plugged into switch port Dell 2 (configured as 'hybrid' because there is no option to access, value 220 PVID, vlan, worth 220 Untagged) and from the server, I can ping IP management dell very well switch and can ping the IP of the gateway of great SG300 so.  On the SG300 switch, on port 2, I plugged in a workstation (configuration is in access mode, vlan 210 unidentified) who can not ping the server plugged into the dell switch.  The workstation, I can ping all the SG300 interfaces and also the IP management dell but I can't ping the server.

  Any ideas anyone can provide is much appreciated!

  Edition of VLAN.

  Lenell, thank you for the call tonight. It seems that we have found the problem. The SIN, although it is configured with a default gateway, the gateway that brings 0.0.0.0. We also checked the NAS works from the same subnet to connect but fails outside of the subnet. Conversely, we checked 2 computers have no problem to connect through the VLAN level 3.

  I hope we got the right direction.

  -Tom
  Please evaluate the useful messages

• Problem with RADIUS and VRF in Cisco 6500

  Hello

  I have the following config of the radius authentication:

  AAA new-model

  AAA authentication login default local radius group

  AAA authorization exec default local radius group

  AAA - the id of the joint session

  IP source-interface Vlan31 vrf LEGACY RADIUS

  Server RADIUS auth-port host 10.10.4.18 1645 1646 acct-port-key 7 XXXXXXXX

  Server RADIUS auth-port host 10.10.5.15 1812 1813 acct-port-key 7 XXXXXXXX

  RADIUS vsa server send accounting

  RADIUS vsa server send authentication

  The work of Don t of authentication

  The sniffer radius server does not detect the Cisco 6500 packages, but the 6500 icmp packets do very well.

  # Ping vrf LEGACY 10.10.4.18 SOUrce VLAN 31 C6500

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 10.10.4.18, wait time is 2 seconds:

  Packet sent with a source address of 10.10.5.254

  !!!!!

  Success rate is 100 per cent (5/5), round-trip min/avg/max = 1/1/1 ms

  interface Vlan31

  XXXX description

  IP vrf forwarding LEGACY

  IP 10.10.5.254 255.255.254.0

  no ip redirection

  no ip proxy-arp

  no ip mroute-cache

  end

  It has fix my configuration?

  Can you help me?

  What IOS version you run on your 6500?

  Try the following:

  AAA new-model

  !

  RADIUS AAA server group RADLegacy

  10.10.4.18 server host

  10.10.5.15 server host

  IP vrf forwarding LEGACY

  !

  Group AAA authentication login default local RADLegacy

  default AAA authorization exec RADLegacy local group

  !

• Problems with unwanted spaces between sentences

  I am updating our website for work and I'm trying to add information on a single page. Whenever

  I hit enter after an entry he adds a huge space between each sentence linked below:

  Lee County
  Population 2000-115 092

  
  Population 2010-140 247
  1990-2000 change - 21.9% increase

  I don't want a space between the two Populations, but no matter what I do, it adds a he. Any advice? Thank you!

  The Enter key is treated as a paragraph break.  So, if you look at your code you will see:

  Lee County
  
  Population 2000-115 092

  Population 2010-140 247
  
  1990-2000 change - 21.9% increase

  If you want just a line break down a single line, you can hit CMD / CTRL + ENTER, entering in the
  pause in your code if it ends with:

  Lee County
  

  Population 2000-115 092
  

  Population 2010-140 247
  

  1990-2000 change - 21.9% increase

  Or alternatively you can put the information in a table of 1-column 4 rows then each cell of the table will give you space.

• Problems with the space between the lines

  My problem is basically this: space keeps appearing between the rows in my table when I saw my page in a browser. The Dreamweaver design view displays without space (I like), but when I take a glance in Firefox or Internet Explorer, unwanted space appear.

  I spent hours scouring the internet looking for the solution to my problem, and none of them does not seem to do the trick. I cellpadding = "0" cellspacing = "0" inside the tag table, which proved to be the answer for others when they have had this same problem, but he has not yet fixed my problem. My CSS specifies also no margin at the top or bottom of the ul and li.

  Anyway, if you could take a look and give me some advice, I would really appreciate it.

  Thank you.

  Here's the html code:

  Home On Work Blog Shop Contact
  	Welcome to the all new amoterocreative.com Title of news Insert brief comments, images and other news here.		Twitter feed here
  	Let's Talk. Phone: 417.622.7432 Electronics: address (at) website Contact form: click here	Let's network. < / h5 > Facebook Twitter LinkedIn

  And the CSS:

  <style type="text/css">
  /*NAVIGATION*/ 
  ul
  {
  list-style-type:none;
  line-height: 1;
  margin-top:0;
  margin-bottom:0;
  }
  
  
  
  /* li */.navli
  {
  display:inline;
  margin-top:0;
  margin-bottom:0;
  }
  
  /* h1 */.nav 
  {
  font-family:Helvetica, sans-serif;
  background-color:#006738;
  text-align:center;
  }
  
  .nav:link {color:#ffffff;text-decoration:none;} /* unvisited link */    
  .nav:visited {color:#ffffff;text-decoration:none;} /* visited link */
  a:hover {background-color:#4D9574;} /* mouse over link */
  .nav:active {color:#4D9574;} /* selected link */
  
  /* Body Text*/
  h2 
  {
  font-family:Helvetica, sans-serif;
  font-size:1.875em;
  text-indent;0px;
  color:#000000;
  }/* 30px/16=1.875em */
  
  h3 
  {
  font-family:Helvetica, sans-serif;
  font-size:24px;
  text-indent;0px;
  color:#000000;
  }/* 30px/16=1.875em */
  
  /* p */.bodytxt
  {
  font-family:"Trebuchet MS", sans-serif;
  font-size:14px;
  text-indent:20px;
  color:#7E7E7E;
  }
  
  /* Sidebar */.side
  {
  background-color:#006738;
  font-family:"Trebuchet MS", sans-serif;
  font-size:14px;
  text-indent:20px;
  color:#ffffff;
  }
  
  .ftnav:link {color:ffffff;text-decoration:none;} /*unvisited link*/
  .ftnav:visited {color:ffffff;text-decoration:none;} /*visited link*/
  
  /* Body Background */ 
  .bdy
  {
  background-color:#d1d1d1;
  }
  
  /* footer */.foot
  {
  background-color:#4C4C4C;
  font-family:"Trebuchet MS", sans-serif;
  font-size:14px;
  text-indent:20px;
  color:#ffffff;
  }
  
  </style>
  

  Hello.. I am a beginner... I don't know if I understand your question... Maybe you could try adding a universal selector(the * symbol) and then to zero the padding of the cell and the margin.

• I'm having a problem with a transition between two clips in the first.

  I put a transition between two clips, but it works only in a single clip. my project is almost done except to fix those errors.

  

  The handles are how you have before and after the section of the video images you removed in the timeline.

  Imagine you put a video in your editing and you use the clip (from the beginning to the end). Then you try and add a second 2 cross dissolve between the shots. First will have to at least 1 second image to prior to the shooting to make the transition, but because that there are no images more to use is unable to dissolve it in the middle of the Cup.

  You can do it all on a track just like FCP of Vegas, but you must have the images it to dissolve in.

• Problem with extra space between vertical li in IE7

  I have developed a CSS site in Dreamweaver. The left menu displays correctly without spaces between list items, in Firefox and Safari, but IE7 puts a space between them. I'm not sure if it's the padding or margin or something else. Here is my CSS code.

  @import url("./whitespace-reset.css");
  @charset "UTF-8";
  {body
  background: #c0b7b2 repeat;
  margin: 0;
  padding: 0;
  text-align: center;
  Color: #000000;
  do-family: Verdana, Arial, Helvetica, without serif.
  }
  #container {}
  Width: 761px;
  background: #FFFFFF;
  border: 0;
  text-align: left;
  height: 871px;
  margin: 0 auto;
  }
  #header {}
  height: 148px;
  Width: 761px;
  padding: 0px 0px 0px 0px;
  margin: 0px 0px 0px 0px;
  }
  {#leftside}
  Width: 158px;
  float: left;
  margin-top:-41px;
  padding: 0px 0px 0px 0px;
  }
  #leftside ul.menu {}
  padding: 0px 0px 0px 0px;
  make-style: none;
  margin: 0;
  }
  #leftside ul.menu li {}
  display: inline;
  list-style: none;
  padding: 0;
  margin: 0;
  height: 1%;
  }
  #leftside {low}
  bottom: auto;
  }
  {#leftspacer}
  Width: 31px;
  float: left;
  height: 723px;
  margin-top:-41px;
  padding-right: 10px;
  background-image: url(images/home_spacer_left.jpg);
  background-repeat: no-repeat;
  }
  #top {}
  margin-top: 0px;
  height: 38px;
  padding: 0px 0px 0px 0px;
  }
  #top ul.menu {}
  margin-top: 0px;
  margin left: 189px;
  float: left;
  padding: 0px 0px 0px 0px;
  margin-right: 0px;
  margin-bottom: 0px;
  list-style: none;
  }
  #top ul.menu li {}
  display: inline;
  list-style: none;
  float: left;
  margin: 0;
  padding: 0;
  }
  {#bottom}
  height: 22px;
  left: 468px;
  }
  #bottom ul.menu {}
  top of the margin: 300px;
  right margin:-23px;
  float: left;
  left margin:-61px;
  list-style: none;
  }
  #bottom ul.menu li {}
  display: inline;
  list-style: none;
  float: left;
  }
  #mainContent {}
  margin: 10px 5px;
  padding: 0 0 0 0;
  }
  #footer {}
  padding: 0; /
  background: #c0b7b2;
  height: 22px;
  }
  {#threepix}
  margin left: 189px;
  margin-right: 0px;
  height: 114px;
  }
  {#col1}
  position: relative;
  }
  #col1-a {}
  position: absolute;
  Width: 275px;
  right: 0px;
  Top: 0px;
  }
  {#col1-b}
  position: absolute;
  right: 0px;
  Width: 275px;
  Top: 0px;
  }
  {#pixcopyleft}
  margin left: 189px;
  do-size: 1em;
  do-family: Arial, Helvetica, without serif.
  margin-top: 10px;
  }
  {#pixcopyright}
  do-size: 1em;
  margin left: 189px;
  do-family: Arial, Helvetica, without serif.
  margin-top: 10px;
  }
  #footer ul.menu {}
  margin left: 189px;
  margin-right: 0px;
  margin-top:-22px;
  padding: 0px 0px 0px 0px;
  float: left;
  }
  #footer ul.menu li {}
  display: inline;
  list-style: none;
  padding: 0px 0px 0px 0px;
  float: left;
  }
  #footer p {}
  margin: 0;
  Padding: 0 10;
  }
  {img.imageleft}
  float: left;
  left margin: 0px;
  padding: 5px 5px 5px 5px;
  }
  {img. ImageRight}
  float: right;
  padding: 5px 5px 5px 5px;
  text-align: right;
  }
  {.imagecenter}
  text-align: center;
  }
  {.fltrt}
  float: right;
  left margin: 0px;
  padding: 5px 5px 5px 5px;
  }
  {.fltlft}
  right margin: 8px;
  }
  {.clearfloat}
  Clear: both;
  height: 0px;
  font size: 1px;
  line-height: 0px;
  }
  H1 {}
  do-family: Arial, Helvetica, without serif.
  do-size: 1em;
  make-weight: bold;
  margin-bottom: 3px;
  }

  Here is a link to the site http://www.Elixir.biz/core/index.html

  starsavage wrote:

  I have developed a CSS site in Dreamweaver. The left menu displays correctly without spaces between list items, in Firefox and Safari, but IE7 puts a space between them. I'm not sure if it's the padding or margin or something else. Here is my CSS code.

  Add the bottom of your css stylesheet:

  #leftside .menu img {}
  display: block;
  }