problems with Win 10 update

Similar Questions

• Problems with Win 7 updates

  Hello everyone,

  For weeks I can't update my Win 7 Home Basic on an ACER PC of detail.

  I get the usual Windows Update screen, it shows the download of updates, but then it shows (0 total KB, 0% complete), while 0% does not change.

  I chose the only feature in the file of 1 MB to see if changes as the download progresses but 0% 0% does not change in 10% or more not even after 40 minutes.

  It seems that something stops the download.

  Please tell us how to make the change from 0% being downloaded.  Thank you.

  Merry Christmas!

  Hi John,.

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  According to the description, I understand that you have a problem with the Windows updates not working only not on the system.

  Certainly, I understand your concern and will try my best to help you.

  There could be a possibility that this issue would have intervened if the updates were not installed correctly on the system.

  I can really imagine the disadvantages suffered by you during the installation of Windows updates. Sometimes it is really frustrating when things do not work correctly with the machine that we are planning and wait. So, we need find the root cause of the problem and I would definitely you help solve the problems in the right direction in order to get this fixed number.

  The question arises if the Windows Update package is not configured properly, or because of incomplete installation. I would say so, you remove any external media connected to the computer and try to crash restart your computer 2 or 3 times and check if you get through this error message.

  In addition to this, I suggest you try the following methods if you are able to boot to the desktop and check if the problem persists.

  Method 1:

  I suggest you run the Windows Update Troubleshooter to check if it works. Please follow the link given below.

  Open the Windows Update troubleshooting tool

  http://Windows.Microsoft.com/en-in/Windows7/open-the-Windows-Update-Troubleshooter

  Note: The troubleshooter above checks if the network card and Windows Update services work properly.

  If the problem persists, follow method 2

  Method 2:

  I suggest you to reset manually the update of Windows components. Please follow the steps outlined in the article below and check if it works.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  Now, you can try to run the Windows updates and check if the steps above to solve the problem.

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

   

• HP cq5600f: problem with Win 10 update

  I have an old Office - cq5600f - and thinking to upgrade to Windows 7 to win 10. The video provided with the machine, NVIDFEA Geforce 6150, card is not usable with 10 victory. I called NVIDEA, and they said that I must determine if the motherboard accept an improved map.  I don't know how to determine that. Someone has an idea?

  Toni, welcome to the forum.

  You must run HP and Windows updates for you ensure that the software and drivers are up to date before you continue.

  There is a PCI Express x 16 slot on the motherboard for a discrete video card.  However, you will need to upgrade the power supply (PSU).  The existing PSU is only 250W.  Most newer video cards require at least 400W to work properly.  In addition, video cards more recent than the GT 640 series require UEFI in the motherboard instead of a standard BIOS.  HP didn't start using UEFI until mid-October 2012.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• Print problems with the recent update to Version 10.11.5

  Print problems with the recent update to the Version of El Capitan 10.11.5.  Cannot print to my Epson and Samsung printers after update to new IOS.  Print jobs get hooked on my Mac Pro.

  Roger 510 wrote:

  Print problems with the recent update to the Version of El Capitan 10.11.5.  Cannot print to my Epson and Samsung printers after update to new IOS.  Print jobs get hooked on my Mac Pro.

  Have you checked with Epson for an updated printer driver?

• seems I'm not the only one having problems with safari after update 9.3 cannot follow the links. Safari blocks. hope it gets fixed quickly. jaa shooting allows to follow the link, but the Web page is not out of good old days. any oher ideas?

  seems I'm not the only one having problems with safari after update 9.3 cannot follow the links. Safari blocks. hope it gets fixed quickly. jaa shooting allows to follow the link, but the Web page is not out of good old days. any oher ideas?

  The 'list' of relevant articles that I know, they are now

  -You can read about the problems in the present statutes and possibly find workaround solutions, particularly in the last

  If you are unable to activate your iPhone, iPad or iPod touch after installing an update - Apple Support

  Apple iOS suspension 9.3 updates for older devices, work on activation fix | IVous

  Apple launches new version of iOS for iPad users 9.3 2 affected by bricking bug | 9to5Mac

  GSM of unfixed addresses Apple iPad 2 Bug with revised Activation iOS 9.3, but the larger question remains - Mac rumors

  If you are unable to activate your iPad 2 (GSM model) update to iOS 9.3 - Apple Support

  9.3 iOS update issues

  Leave a post by: ChitlinsCC

• Anyone know if there is a problem with the "Windows Update" site? Since May 11, 2010...

  Anyone know if there is a problem with the "Windows Update" site? As of May 11, 2010 I could not access it for 2 days now.  I get an error report indicating that he has a "problem with the site '... Not sure if it's my computer or the site itself. I just need to check updates and download them. I would be grateful for any feedback...  Thank you!
  ~ Jenifer

  It is without a doubt.  There were a few patches published today, and I was able to update all my machines successfully.  This looks more like a virus problem.  Have you run a virus scan recently?  Many times, if you are infected the virus will prevent you to access Windows Update.

  You can also use Microsoft Fix It to reset the Windows Update components: http://support.microsoft.com/kb/971058.  This could also be your problem.

  Let me know how it goes,

  Barbara

• I am also having the same problem with the same updates. I have Windows XP SP3 and it's updates with the problem.

  I am also having the same problem with the same updates. I have Windows XP SP3 and it's updates with the problem.

  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2572073)
  A security update for .NET Framework 2.0 SP2 and 3.5 SP1 on Windows Server 2003 and Windows XP x 86 (KB2518864)
  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2633880)

  They all install properly but switches back to windows update to install. It's some kind of loop.

  Hi billy73,

  In addition, if you still have questions, please take a look at the thread similar here with a solution as possible.

  I hope this helps!

• Problems with Windows VISTA update (error code: 9 c 47 of the 800070002, D 80024200)

  original title: problems with Windows VISTA update

  I'm using Windows Vista (SP2). Windows update is not able to update the following updates on my system. Whenever I get these error messages.

  1. 9 47 code
  2. Code 800070002
  3. Code D 80024200.

  Is there a resolution to do the same thing?

  Hello

  Did you change your computer?

  I suggest you to follow the methods and check.

  Method 1:

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  Method 2:

  If you have installed a security software on the computer, then I suggest you try to disable temporary and check to see if the same problem happens. Make sure that you enable security software back once the diagnosis is made to prevent the computer from virus attacks.
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Method 3:

  How to troubleshoot Windows Vista and Windows Server 2008 service pack installation issues

  http://support.Microsoft.com/kb/947366

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• problem with win 7 and 8 of 32-bit

  Mr President, I have a PC with win 8 running. It has 4 GB of ram and processor Intel dg41cn. I installed win 8 after watching win 7 ultimate crash suddenly and lose the whole unsaved data. I thought it was a problem with win 7. but the same problem occurs with win 8 pro 32-bit. now a new problem 8 victory also blocks the same way and when we start it shows 'no operating system found... "but when we shake the cables attached to cpu it starts... now what conclusion do this? What can I do to fix this

  Hardware problems, shorts and/or bad connectors...

  Solution is to repair/replace the material once the short exact question / connector is located.

• Satellite Pro L850 1DR - problems with Windows 7 update KB2887069

  I have problems to install the KB2887069 update.

  It seems to install OK... prompt me to restart... when I do it, says it configures... GETS to 7%, then starts rebooting... watch it configures again... up to 7 or 9%... and then reports it is defect and restoring... restarts again... and it is quite... not installed and reference to Windows Update confirms it failed.

  All the other updates I had installed today very well once I realised KB2887069 was the problem and failed to update.

  I am running Win 7 Prof Serv Pack 1 64 - bit on a Toshiba Satellite Pro L850 1DR. I use my AV Microsoft Security Essentials software.

  For now I had to hide the update... but all of the bright ideas how overcome the problem. I tried the Microsoft site, but there is still no answers who brought a solution for me.

  Thanks in anticipation!

  I googled around for KB2887069 update and it seems that you are not alone with this problem to Microsoft Update. I also found your request in the forum, Ms.

  In other words, that's not a problem of mobile by this must be resolved by Microsoft.

  I read in the MS forum on this issue and this issue is still under investigation.

• Problems with videodriver after update BIOS on my SP4600

  Hello
  I did a bios update and installed win 2000 on my satellite pro 4600...
  He was working before the bios update, also with win 2000.
  When I installed the video driver, my laptop didn't work anymore. With safe mode I ve uninstalled the video driver, and the system worked again, but only with 16 colors.
  Is there someone who has recognized this and has a solution for this problem?
  Help please, if possible in Dutch!

  (Sorry for the bad English)

  Kind regards

  Arthur

  Hello, Arthur

  It's very strange question. It's really not known drivers me the BIOS update can do some influence on some installed.

  Have you tried to install the Toshiba established the Toshiba download page 5.8.12.522 driver version?

• Problems with Win 7: lost internet connection and downloads

  Hello

  I'm not sure that the two problems are related... I don't know what topic to choose.

  I have a custom, with Win 7 machine, and I install all required updates. But for a while (months? I turn it off every night) it says 15 updates are available every time that I reboot, and I see no updates installed (I search for installed updates today).

  Anyway, let them go all the way, and when I restart, I have no connection. It's happened several times (everytime I reboot). Maybe that I had the chance to solve the problem by restarting (and reinstalling :)) 15 updates, but today I can't. I am connected by wire to a modem. Our all other computers work.

  I have a job in the process and need my internet connection (easier to work on a desktop computer with large screen of a laptop) and I can't.

  In network and sharing Center, there is a cross between 'Several networks' and the internet. I have the message if I 'connect or disconnect' "no Internet access.

  I did ipconfig, and I get media disconnected. I did not unplug anything!

  I would be very grateful for your help.

  Thank you very much

  Hi Allwyna,

  Thanks for the reply.

  As you said, there are 16 updates that never completed the installation. There could be opportunities updates are at the origin of the problem. So before solve us the connection problem. We should go ahead and first to solve the problem of updates.

  I would like to know you have installed any Security Antivirus software on your computer, if so I first suggest you temporarily disable the Antivirus software install on your computer and check if that helps.

  Warning: Antivirus software helps protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you have to temporarily disable it to install other software and/or any relevant issue, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks by malicious software.

  Try the methods.

  Method 1:

  I suggest following the steps listed in the article and check if it works.

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows/troubleshoot-problems-installing-updates#1TC=Windows-7

  Method 2:

  I suggest you to manually reset windows update components.

  http://support.Microsoft.com/en-us/KB/971058

  NOTE: This section, method, or task contains steps that tells you how to change the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/ )

  How to back up and restore the registry in Windows

  I hope this helps. Please let us know the results. We will be happy to help you further.

   

• Problems with scrolling after update

  IM currently using the BlueJ ide and after updating to the new system / update (macOS Sierra) there is significant lag / jitter when scrolling. This problem only occurs when you use the scrolling with two fingers with the touch pad. When I use a mouse / or click the scroll bar on the side, it seems to go well. Not sure if there is a problem with BlueJ or the new OS. Would be very interested for some suggestions on how to fix this very annoying problem. (Using a Macbook pro 13, 2015).

  Thanks a lot to all the answers

  The obvious question would be if you see the problem of scrolling in Mac OS standard applications such as Mail, Notes and Safari.

  If this isn't the case, it is likely BlueJ.

• Problem with the new update

  Any browser looks graphically unstable and content is empty with the new update, is it just me or is just the update which is unstable?

  Hello

  Try disabling graphics hardware acceleration. You will have to perhaps restart Firefox for it to take effect, so save any work first (e.g. you compose mail, documents online that you are editing, etc.).

  Then perform the following steps:

  1. Click the menu button

     

     then select Options Preferences on Mac or Linux, or Windows.

  2. In the window of Firefox Options (or preferences), click on the Advanced tab, and then select general.
  3. You will find in the list of parameters, the checkbox use hardware acceleration when available . Clear this check box.
  4. Now restart Firefox and see if the problems persist.

  In addition, please check the updates for your graphics driver by following the steps in the following knowledge base articles:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox
  • Update your graphics drivers to use hardware acceleration and WebGL

  This solve your problems? Please report to us!

  Thank you.

• Problem with Safari, after update

  I use a MacBook Pro, OS X Yosemite, 10.10.5 - and after the last update, I have problems with Safari (version 9.1). Some Web pages I visit every day is more responsible (I get the message that the page needs to be recharged because she failed the first time, but this does not work then either). This problem started just after the last update. Does anyone else have this problem? What I have to go back to the previous version or can I fix this problem?

  If you have problems to open Web pages, take a look at these techniques proposed by Apple of troubleshooting.

  https://support.Apple.com/en-us/HT204098

  Go to the Safari menu (at the top right of your screen next to the Apple icon), choose 'Quit Safari'

  Press the "Shift" key and while holding this button on your unique keyboard, click the icon of Safari on your Dock.

  Open Safari - Preferences - Privacy - data to remove any Web site.

  Open the menu to go with the Option (Alt) key - library - key locate Safari folder and place it on your desktop. Restart your Mac, open Safari and delete the file from your desktop.

  Also, try the following steps:

  Restart your Mac.

  Try to start:

  -Stop your Mac

  -Wait until your computer turns off and after that press the power button

  -Just after you hear the startup tone, press in and hold the SHIFT key

  -Release the SHIFT key when you see a gray Apple sign and the progress under this sign bar

  -Once your Mac boot, restart dhcpd as you usually do.

  If this does not help, follow the instructions below:

  -Stop your Mac

  -Wait until your computer turns off and after that press the power button

  -Just after you hear the startup tone, press in and hold the SHIFT key

  -Release the SHIFT key when you see a gray Apple sign and the progress under this sign bar

  -Once you see office, start a scan Disk Utility to detect and repair file system errors (remember to choose your primary hard drive)

  -Click on the disc to check, then, if requested to solve the problems on the repair disk

  -After that click on verify disk permissions, and then click Repair disk permissions

  -Once the process is complete, stop your Mac and turn it on again after 30 seconds

  I hope this helps!