problems with wireless after the motherboard, cpu and ram upgrade adapters

As the title says, I have recently updated my card mother, cpu and ram (increased from Asrock extreme6 z77/i7 3770 k/Kingston 8 gb hyperx for EVGA ftw/i5 z97 4670 k/g. Skill ripjaw x 16 gb). I always use the same installation of Windows 7 64 via the same SSD. After I was installing new equipment, I used the disc that comes with the motherboard and installed all the drivers that were available (twice, just to be safe). All the features of the OS I had before seem to be there except to exit Device Manager to correctly install the drivers for my wireless (Linksys AE1000 and TP Link N900) adapters. I downloaded the current driver for the Linksys Web site and I have the disc for the TP-Link and I tried several times to install, but keep the same message ' Windows found driver software for your device, but has encountered an error trying to install it. Device Manager recognizes the device and it is not any question of State symbol (IE yellow triangle, etc.) that is displayed in conjunction with an adapter. I tried disable/re-enabling and uninstall/re-installing times and keep having the same problem. I tried to search in several forums of people with similar problems, but none of the resolutions seem to work or are suitable for my situation. Any help that can be provided would be greatly appreciated. Thank you.

Hello

When you upgrade your motherboard, cpu and ram, drivers for particular devices may not be related to other drivers. That's why I suggest you to install all the drivers for the chipset from the manufacturers website and see if that helps.

Tags: Windows

Similar Questions

  • Diagnostics Windows network, the error reads 'Problem with wireless adapter or access point' and fails to solve the problem.

    «Problem with access point or wireless adapter»

    Hi, I just bought a new laptop & I have the extreme difficulty to stay connected to the internet. When I run Windows Network Diagnostics, error reads 'Problem with wireless adapter or access point' and fails to solve the problem. Help, please... Thank you, Maria

    HI Maria,

    ·         What operating system is installed on your computer?

    ·         You have installed the latest drivers for wireless network card?

    Follow the suggestions below for a possible solution:

    Method 1: Start your computer in a clean boot state in order to check if the applications of third parties or startup items is the origin of the problem.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

     

    Note: After troubleshooting, make sure that you configure the computer to start as usual as mentioned in step 7 in the above article.

    Method 2: See these articles for solve wireless problems:

    Why can't I connect to the Internet?

    http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

     

    How can I troubleshoot network card?

    http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

     

    Windows wireless and wired network connection problems

    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Let us know if that helps.

  • Change of motherboard, cpu and ram by using the version of upgrade of windows 7

    I plan on upgrading my motherboard, cpu and ram. I am using windows 7 Home premium that I have updated from xp using a retail upgrade disc that I bought from a company of national computer supplies. Should I have any problems activating this the wrench that came with the drive. I have read several posts on this but can't seem to find a definitive answer. Help, please!

    Well, Windows XP and Windows 7 are versions of upgrade as you claim, that means XP used a qualifying version of Windows that is pre-installed with the system used the upgrade of the command.

    This means, Windows XP and Windows 7 are both related to this version of Windows that came with the system. Because the copy of the original Windows supplied with the system would have been an OEM license, which means, Windows 7 and XP have more rights to transfer if you change the motherboard.

    You can always try a clean install with upgrade.

    How to do a clean install with upgrade disc:

    Boot from the Windows 7 DVD

    Click Install now

    Accept the license agreement

    When the option is displayed to select a type of installation, click (Custom advanced)

    Click on drive Options

    Select the disc/s click on Delete

    Click new

    Click on apply

    Click OK

    Click Format, and then click next to proceed with the installation

    Skip entering your product key Windows 7 and complete the installation.

    When you reach the desktop, click Start, right-click on computer

    Click on properties

    Scroll down to the Windows Activation

    Click the link x days before activation.

    Click on the link that says: "show me other ways to activate.

    Enter the product key

    Click next

    Select the Activation of the phone

    Click Next when you enter your key page

    Select your country

    Click Next, call the number listed

    Be sure to explain your situation to the Appeals Officer.

    Provide the installation generated when ID requested by the call agent

    They give a confirmation ID in return, enter it

    Click next to complete the activation.

    or

    How to activate Windows 7 manually (activate by phone)
     
    1) click Start and in the search for box type: slui.exe 4
     
    (2) press the ENTER"" key.
     
    (3) select your "country" in the list.
     
    (4) choose the option "activate phone".
     
    (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
     
    (6) explain your problem clearly to the support person.
     
    http://support.Microsoft.com/kb/950929/en-us

  • Updated the motherboard, processor and RAM and upgraded to Windows 7 Ultimate 64 bit, after upgrade the external hard drive encrypted with bitlocker will not enter the password.

    Original title: bitllocker Windows 7 issue

    Hello

    I recently updated my motherboard, processor and RAM, but I kept my original 500 GB hard drive, and equipped with a hard drive 2 TB extra, after the upgrade, I downloaded windows 7 ultimate 64-bit. After the upgrade I plugged my external hard drive (which has all my stuff important on it, that is to say the photo, video etc.) to realize that I had he encrypted with bitlocker on my old sysem. It allows Me to enter my password, it looks for a USB flash drive key, I did not. My question is:

    Can I replace my old system with the old motherboard, hard drive and the original RAM to remove the external hard drive for bitlocker?

    I still have the file windows.old on my hard drive, I have to restore it and remove the most recent version of windows 7 off the drive. I do this before I rebuild my old PC? I'm stuck here and would not lose all my photos (the wife would kill me!) I would appreciate your help.

    Hello

    Reassembly of the old computer won't help. You will always need the key to open the Bitlocker.

    You can read the articles and check:

    What is the difference between BitLocker Drive encryption and EFS file system?

    Protect your files using BitLocker Drive encryption

    In Windows 7 BitLocker Drive Encryption: frequently asked Questions

    Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

  • Windows Vista Home Premium does not start after mother, CPU and RAM upgrade card

    I recently updated my PC Windows Vista Home Premium. I changed the motherboard, CPU, RAM and video card. When I booted the machine, it has not started Windows. Windows tried to recover, but could not. Is it possible to get this machine to start without doing a new install? The new facility will lose important files.

    Hello

    It's a normal reaction after replacing the hardware that you have replaced.

    The hard drive with the installed operating system contains the old motherboard drivers, etc..

    They must be replaced with the new motherboard, drivers etc.

    You will need to reinstall the operating system and then install the new drivers of motherboard (you should have a diskette of drivers for it), if the new installation does not probably them, that it will not...

    To backup your data > buy a hard drive USB enclosure > put your hard drive in it > plug it into another computer > read and copy your data from it in this way.

    See you soon.

  • Problem with vibrations of the Iphone 5 and SE

    Hello, my name is Alexander, im of the Brazil and I speak very well English. I owned an Iphone 5 purchased in Italy in September 2012 and I used it until today 02/08/16 when I decided to buy a SE 64 GB my iphone because Iphone 5 was a problem that could not be resolved. I used it and noticed the battery was swelling and suddenly the Iphone 5 continues to vibrate in all operations. I took it to the interview and they changed the vibrating motor and the power cable, cable, but does not work. I thought it might be a problem with the motherboard by the blown battery occurried. So I decided to buy a SE 64 GB and when I restored the Iphone 5 in SE, it runs with the same problem. The store give me another a 64 and after the restored backup, the same problem occuried. They had upgraded the operating system, but the only way to solve it was a complete reset of fabric and make a backup of restore contacts and photos through the Icloud

    Can someone help me?

    There are a few app couldn't stop the iphone vibrates? without all my applications and files, the SE Iphone works fine

    I don't know if you want vibration on or off. Anyway, this is the setting you are looking for...

    Settings > general > accessibility > vibrations

  • Problems with aero after the latest updates

    Hello

    Someone had a problem with the latest Microsoft security updates
    touching the aero desktop theme.

    Since I downloaded the updates my aero as a theme stopped working.
    I did a roll windows back but I still have the same problems.

    The updates are #KB971029 and #KB971029 the
    updates have been downloaded on 03/17/11

    I hope someone can help with this problem.

    All the best

    Philip Davies

    Hello

    OK try to remove these updates to see if that helps. Sometimes manually
    install the updates one at a time will prevent topics such as this one (if the)
    mises_a_jour have been the question).

    Control Panel - Windows Updates - lower left Installed Updates - uninstall or change

    Or

    Remove an update
    http://Windows.Microsoft.com/en-us/Windows-Vista/remove-an-update

    Or

    The problems with the removal of updates
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-removing-updates

    Or

    How to uninstall updates in Windows Vista
    http://www.vista4beginners.com/how-to-uninstall-Windows-Vista-updates

    Disable or hide optional updates on Windows Vista
    http://www.howtogeek.com/HOWTO/Windows-Vista/disable-or-hide-optional-updates-on-Windows-Vista/

    AFTER removal of updates, do a system restore to before
    updates have been applied to the origin. Therefore, affect the total amount of
    updates are deleted.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
    =======================================================

    If necessary:

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    ======================================================

    If necessary try a repair Installation which allows to keep the programs and data however
    redundant backups are always a good idea.

    You can use another DVD that aren't copy protected but you you need to own
    Product key. It must be the same version 32 or 64 BIT Vista OEM. Also the system
    machine to usually sell the cheap disk since you already own Windows. Don't forget to make a
    good backup or 3 (security in redundancy).

    On-site upgrade
    http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

    How to perform a repair for Vista Installation
    http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

    I hope this helps.

  • problems with rv042g after the software upgrade

    After the software upgrade it reboot the router on every 45 seconds

    I tried this tool from Cisco RV0xxV3_FirmwareRescueUtility_v4.0.0.7 Web site without success, the problem is there, is one way that you can get the router up and running again?

    Can I run a TFTP server and download new software, or I ther a FirmwareRescueUtility for rv042g?

    Mogens Demmark

    The first firmware comes with RV042G is 4.2.0.03, so the firmware utility rescue v4.0.0.7 would not work.

    Given that your will to power cycle automatically RV042G every 45 seconds, and the problem has not disappeared after that you did a reset to factory default, the unit needs a new firmware downloaded. Please, try the following steps.

    1. disconnect the power cable to the unit.

    2. hold the reset (using a paperclip) button, while plugging in the power cable.

    3 look at the DIAG LEDS.

    4. release the reset button when you see the DIAG led are flashing.

    5. a flashing DIAG indicates that the unit runs in start mode, and a server tftp on the device is waiting for a picture of fresh firmware to the address 192.168.1.1.

    6. set up your PC with an IP address in the subnet 192.168.1.x, e.g. 192.168.1.100 and specify as default gateway 192.168.1.1.

    7. try to ping the unit with 192.168.1.1, and you should see a response from the unit.

    8. run a program client tftp (with a command line) and push an image good firmware, for example

    TFTP-I 192.168.1.1

    If the procedure above does not resolve the problem, contact the support center for RMA.

  • Problems with images after the subclips

    Hey there

    Today I woke up to see all subelements, I made my most recent project. Just today, footage looked more pixelated and blurry.

    What might of happened? When I stop the image the quality is exactly as it was before. But when played his more pixelated.

    Some of the images was shot at a lower resolution, but when I put the size of the screen to the appropriate resolution quality always looks bad.

    Would this have something to do with the manufacture of the subitems? Even go back and see the clips that came the subclips: the film is even more 'pixely '.

    Any help appreciated

    @

    Hi pavalanche11,

    Sorry for the problem. If it is fixed?

    Please consider these points for this problem:

    1. it looks in any case related to subitems.

    2 as you mentioned after a break the clips, they look very good, but not the same case playing; It could be linked to the resolution Pause and play in the monitor Panel.

    You can get these settings, either by clicking the exit button in the lower right of the monitor Panel or by right clicking on the items in the monitor Panel.

    3. you also said that you pulled these clips at a lower resolution. By changing the values in the resolution of reading as suggested above, they may work properly.

    Here is the text of pdf help Prelude:

    Some formats are difficult to display in full motion by reason of their high compression or broadband playback. A lower resolution playback faster but at the expense of the quality of the image. This compromise is particularly visible when you view the other H.264 and AVCHD-based codec of the media. Less than full resolution these formats have turned off error correction, and artifacts are common during playback. These artifacts, however, do not appear in the exported media.

    Use separate reading and resolutions of break to better control the monitoring experience. With images high resolution, resolution of the reading to a lower value (for example, 1/4) for smooth playback and the resolution of the break in full. These settings allow you to check the quality of the details of development or the edge when you stop playing. Cleaning put the monitor resolution of reading, stop no resolution.

    I hope it helps. Customer feedback is important to us. Continue to write in the case of any confusion.

    Thank you

    Mayjain

  • The problem with SQL after the migration of the database to another machine

    Having a SQL strange problem trying to extract a database being moved from one machine to the other.  Both machines are running SQL 2008 32-bit and are both Windows 2008 servers.  When I try to backup the database using the SQL tools and restore the. BAK file on the new SQL Server, I get the following error:

    Restore failed for server 'servername' (Microsoft.SqlServer.Smo)
    Additional information:
    System.Data.SqlClient.SqlError: RESTORE detected an error on the page (44:2097184) in database 'RestoreDBName' read from the backup set.

    Similarly, when I am trying to copy the. MDF and. LDF files to the new server and tie them, I get the following error:

    Attach the database failed for the server 'servername '.
    Additional information:
    An exception occurred during the execution of a Transact-SQL statement or batch.
    A system assertion failed.  An assertion failure is usually caused by a corruption of data or software bug.  To check the database, consider running DBCC CHECKDB.  If you have agreed to send images to Microsoft during installation, a mini dump will be sent to Microsoft.  An update can be an available from Microsoft in the latest Service Pack or a QFE from Technical Support.
    Could not open new database 'NewDatabaseName' create a DATABASE is dropped.
    "" Location: "logmgr.cpp": 3277
    Expression: lfh-> lfh_startOffset is startOffset
    SPID:55
    PID: 292876 (Microsoft SQL Server, error: 3624)

    Everything I've read, these errors usually indicate some sort of database corruption.  However when I run DBCC CHECKDB on the database on the source server, it is up to perfectly don't own... None detected corruption.  In fact, this server hosts 8 different databases.  Departure from all the correct DB on the source server, none of them will restore however to a new server using one of the methods above.  I'm having a hard time to believe that each of them could be corrupted when they show absolutely no indication of a problem.

    Anyone have any ideas?

    Try to make the backup and restore via SQLCMD (or via a query in SQL Server MS window).

    The backup will be the following (obviously, change "MaBase" and "D:\BACKUPS" to some database and the location you wish to save - just using for example):

    BACKUP DATABASE MyDatabase

    TO DISK = 'D:\BACKUPS\MyDatabase.bak. '

    WITH NOFORMAT, NOINIT,.

    NAME = 'Database MyDatabase - Full Backup',

    NOREWIND, NOUNLOAD, STATS = 10, SKIP

    Copy your backup to the other server and file make:

    RESTORE the DATABASE to MyDatabase

    FROM DISK = 'E:\Backups\MyDatabase.bak' WITH FILE = 1,

    GO to "MyDatabase_Data" to "E:\SQLDATA\MyDatabase_Data.mdf,"

    GO to "MyDatabase_Log" to "E:\SQLLOG\MyDatabase_Data.ldf,"

    NOUNLOAD, STATS = 10 REPLACE

    Again, change your names and locations in function.

    If this does not work, try to restore a database by third-party tools. You can find them in Google. If you don't want to spend the time to research, you can try a tool SQL Server Recovery Toolbox. All the details about this program on the link. http://www.oemailrecovery.com/sql_repair.html

  • problem with ' law of the administrator. type' and cannot be changed to the user Act.

    (this is a PC at HOME, I'm the only person to use it) - after change to the administrator account, problems arise.  I can't click and open Excel or Word files on the desktop, I open Excel or Word first, and then recover my files there.  So I want to change my administrator account to the normal user account, but it does not allow me to do.  I click, click standard - it does not.

    I can't find any advantage by using the law of the administrator.

    I also tried some methods of Forum - they do not work

    So, what can I do to restore my normal user account administrator account.

    WaiHar

    After change of [my account] to the administrator account, problems arise. I can't click and open Excel or Word files on the office. 

    -> What exactly happens when you try?

    I also tried some methods of Forum - they do not work

    -> What methods could they have been?

    So, what can I do to restore my normal user account administrator account.

    -> There is no need to change your administrator user account.

    -> What really makes you think that your account has administrative privileges?

  • Problems with masks after the sequence first SpeedGrade back (CC)

    Hello

    I'm color ranking a clip in SpeedGrade CC using the new direct link function. For calibration of the colors I used masks and also the different layers. Once I'm done, I sent my sequence back to first Pro CC.

    I see, first shows me exactly the color correction, I did in SpeedGrade, except for one thing:
    The places where I used the masks in SpeedGrade to illuminate their for example a little until now are filled with lines pixeled...
    I thought it's just a problem with the preview, so I exported it. Slept pixeled lines.

    Once again: in SpeedGrade is all fine, but when I send the return sequence to the first there are those pixels.

    It's really irritating because one day before it worked fine with no problems and I was virtually the same as now.

    Please help me if you can! Thank you!

    Ok.

    The GPU acceleration is turned on?  Have you tried to turn it off?  You have a card AMD or nVidia?

  • HP ENVY 15: Problem with audio after the Windows 8.1 update

    Hi, I'm on HP ENVY 15 notebook PC and I updated my windows 8 to 8.1. Until a few days back, everything was fine. However, now, I have no audio through speakers or head phones. Can someone help me please to solve this. Thank you.

    Product number: E4N80EA #ABZ

    Hello

    Try the following.

    Download IDT Audio Installer on the link below and save it in your downloads folder.

    http://ftp.HP.com/pub/SoftPaq/sp63501-64000/sp63555.exe

    One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

    When you are finished, download and reinstall the Chipset driver from the link below.

    http://ftp.HP.com/pub/SoftPaq/sp63001-63500/sp63408.exe

    Once the reinstallation is complete, shut down the laptop by pressing the SHIFT key when you click Shutdown to temporarily prevent a hybrid boot.  Then disconnect the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

    Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f5 to load the default values (sometimes it's f9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

    Allow Windows to fully - charge it will automatically load an audio driver, but let just this complete.  Then open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.  Once this done, do a right-click the speaker icon in the taskbar and select playback devices.  'Speakers and headphones' left click once to highlight, and then click the Set Default button - check if you now audio.

    Kind regards

    DP - K

  • Will there be proactive with moderation after the 10 June 7 to upgrade?

    This is my first post on this topic (or any other) Oracle Forum.

    I want to know if my messages and responses here will be immediately available for others to view, or they will be subject to a delay caused by the need for a "moderator" approve my presentation.

    I looked at the FAQ for this forum, and I understand that it is subject to moderation after the fact (which is understandable and good).

    Thank you!

    Breck

    Addendum: When I posted this question, a message appears saying that there is a "slight delay" before she was visible... but the delay was very short. She says some kind of automatic process of moderation before the fact, or he says there is a huge room full of human moderators responding with wonderfully inhuman speed?

    Published by: 1008875 on May 30, 2013 06:35

    1008875 wrote:
    This is my first post on this topic (or any other) Oracle Forum.

    I want to know if my messages and responses here will be immediately available for others to view, or they will be subject to a delay caused by the need for a "moderator" approve my presentation.

    All messages are immediately available for all people who are recorded in this forum.

  • Overclocking CPU and RAM upgrades!

    Hello, first of all thanks for the beautiful vostro 230 desktop I bought it its been 3 years. Not a single problem with it. Its good for the last year, but now a day I am not satisfied of its speed and reliability. Lack of funds, I can just build or buy a new desktop computer, so I was wondering if I can overclock the processor to make my pc faster.
    So here are my questions:

    1. can I overclock the precessor of VOSTRO 230 pc (Intel core 2 duo E7500 2.93 Ghz processor)? If yes how?

    2. I want to improve my RAM. I know that the maximum support for vostro 230 is 4 GB. But I do not understand that it supports 4 GB single slot or 2 GB in slot double? What is the value maximum frequency this motherboard supports?

    Please help me with this problem. I look forward to your response... response as soon as POSSIBLE...

    Thank you

    Lenora Patra

    Sorry to say, the Vostro 230 cannot be overclocked.

    The maximum RAM supported, is 4 GB (2 x 2 GB modules).

    http://www.crucial.com/USA/en/compatible-upgrade-for/Dell/Vostro-230-Mini-Tower

    Bev.

Maybe you are looking for

  • Uninstall conversations TB add-on

    I tried the Conversations of Thunderbird Add-on, but has decided to disable and uninstall, but it seems to always work, grouping my emails by conversation. How can I get rid of this feature? Thank you

  • Qosmio F60 - no sound

    Qosmio F60 - no sound. Can not read the CD or DVD. Help please. It must be something so simple... but I'm stuck

  • Are there benefits thanks to apple to reach Advisor top-level posts

    I work for a retailer of Verizon and the benefits to get knowledge and experience helping people solve problems, I see even a potential for maybe even get some business out of it. But this is what apple offers to put in the time and helping at this r

  • Pulse width depends on the number of pulses (pci-6602)

    Hello I'm trying to generate samples done with pci-6602. I use CO Pulse ticks + implicit options External impulses is 1ms 1PPS pulse from the trimble GPS receiver If I set the number of pulses = 1, then I had to pulse length (high ticks - 1) = If I s

  • TestStandPersistedOptions

    Hello What is TestStandPersistedOptions? Thank you Rafi